All but one TGI drivers didn't use IRQs. Especially when the TGI driver kernel was the only .interruptor this meant quite some unnecessary overhead because it pulled in the whole IRQ infrastructure.
The one driver using IRQs (the graphics driver for the 160x102x16 mode on the Lynx) now uses a library reference to set up a JMP to its IRQ handler.
All but one joystick drivers didn't use IRQs. Espsecially when the joystick driver kernel was the only .interruptor this meant quite some unnecessary overhead because it pulled in the whole IRQ infrastructure.
I was told that the one driver using IRQs (the DXS/HIT-4 Player joystick driver for the C64) can be reworked to not do it. Until this is done that driver is defunct.
So far the joy_masks array allowed several joystick drivers for a single target to each have different joy_read return values. However this meant that every call to joy_read implied an additional joy_masks lookup to post-process the return value.
Given that almost all targets only come with a single joystick driver this seems an inappropriate overhead. Therefore now the target header files contain constants matching the return value of the joy_read of the joystick driver(s) on that target.
If there indeed are several joystick drivers for a single target they must agree on a common return value for joy_read. In some cases this was alredy the case as there's a "natural" return value for joy_read. However a few joystick drivers need to be adjusted. This may cause some overhead inside the driver. But that is for sure smaller than the overhead introduced by the joy_masks lookup before.
!!! ToDo !!!
The following three joystick drivers become broken with this commit and need to be adjusted:
- atrmj8.s
- c64-numpad.s
- vic20-stdjoy.s
The constructors are _NOT_ allowed anymore to access the BSS. Rather they must use the DATA segment or the INIT segment. The latter isn't cleared at any point so the constructors may use it to expose values to the main program. However they must make sure to always write the values as they are not pre-initialized.
The name RAM doesn't make much sense in general for a memeory area because i.e. the zero page is for sure RAM but is not part of the memory area named RAM.
For disk based targets it makes sense to put the disk file more into focus and here MAIN means the main part of the file - in contrast to some header.
Only for ROM based targets the name RAM is kept as it makes sense to focus on the difference between RAM and ROM.
The way we want to use the INITBSS segment - and especially the fact that it won't have the type bss on all ROM based targets - means that the name INITBSS is misleading. After all INIT is the best name from my perspective as it serves several purposes and therefore needs a rather generic name.
Unfortunately this means that the current INIT segment needs to be renamed too. Looking for a short (ideally 4 letter) name I came up with ONCE as it contains all code (and data) accessed only once during initialization.
- Put a BASIC-language stub at the beginning.
- Removed the Autostart flag.
Those changes make it easy to give command-line arguments to a program.
* Made the Atmos configure file accept a special symbol definition on ld65's command line. We can use "__RAMEND__" to increase the amount of RAM that's available to programs.
Up to now static drivers were created via co65 from dynamic drivers. However there was an issue with that approach:
The dynamic drivers are "o65 simple files" which obligates that they start with the 'code' segment. However dynamic drivers need to start with the module header - which is written to. For dynamic drivers this isn't more than a conceptual issue because they are always contain a 'data' segment and may therefore only be loaded into writable memory.
However when dynamic drivers are converted to static drivers using co65 then that issue becomes a real problem as then the 'code' segment may end up in non-writable memory - and thus writing to the module header fails.
Instead of changing the way dynamic drivers work I opted to rather make static driver creation totally independent from dynamic drivers. This allows to place the module header in the 'data' segment (see 'module.mac').
This change was suppsed to fix the issue that the former JUMPTABLE is merked as 'ro' while it is actually written to in several scenarios. When drivers are converted using co65 and then compiled into ROMs the JUMPTABLE isn't copied to RAM and therefore the write operations in question fail.
However unfortunately I didn't succeed in changing that :-( Just setting the former JUMPTABLE to 'rw' broke the drivers. So I placed the DATA segment directly after the former JUMPTABLE segment. This made the drivers converted with co65 work again - obviously after changing libsrc/Makefile:235 from '--code-label' to '--data-label'. But the actual dynamic drivers still didn't work as the former JUMPTABLE wasn't placed as the beginning of the loaded file anymore. That effect could be changed by exchanging src/ld65/o65.c:1391 with src/ld65/o65.c:1394 but doing so broke the drivers again :-((
- No complex shell logic.
- "Source file shadowing" for all targets via vpath.
- Dependency handling.
- True incremental build.
- Don't write into source directories.
- Easy cleanup by just removing 'wrk'.
- No complex shell logic.
- "Source file shadowing" for all targets via vpath.
- Dependency handling.
- True incremental build.
- Don't write into source directories.
- Easy cleanup by just removing 'wrk'.
black-and-white driver and a color-palette driver, at the same time. That
cannot work on the Oric's architecture. This patch makes it be only a
black-and-white driver.
git-svn-id: svn://svn.cc65.org/cc65/trunk@5955 b7a2c559-68d2-44c3-8de9-860c34a00d81
