The name RAM doesn't make much sense in general for a memeory area because i.e. the zero page is for sure RAM but is not part of the memory area named RAM.
For disk based targets it makes sense to put the disk file more into focus and here MAIN means the main part of the file - in contrast to some header.
Only for ROM based targets the name RAM is kept as it makes sense to focus on the difference between RAM and ROM.
The way we want to use the INITBSS segment - and especially the fact that it won't have the type bss on all ROM based targets - means that the name INITBSS is misleading. After all INIT is the best name from my perspective as it serves several purposes and therefore needs a rather generic name.
Unfortunately this means that the current INIT segment needs to be renamed too. Looking for a short (ideally 4 letter) name I came up with ONCE as it contains all code (and data) accessed only once during initialization.
Moving __cwd from BSS into INITBSS does of course ;-) not only impact the CBM targets but all targets with disk I/O support.
Note: Code using `__cwd-1` may trigger an ld65 range error because __cwd may end up at the very begining of a segment. As far as I see this is an ld65 bug which I'm not try to fix - at least here.
So far the INIT segment was run from the later heap+stack. Now the INIT segment is run from the later BSS. The background is that so far the INIT segment was pretty small (from $80 to $180 bytes). But upcoming changes will increase the INIT segment in certain scenarios up to ~ $1000 bytes. So programs with very limited heap+stack might just not been able to move the INIT segment to its run location. But moving the INIT segment to the later BSS allows it to occupy the later BSS+heap+stack.
In order to allow that the constructors are _NOT_ allowed anymore to access the BSS. Rather they must use the DATA segment or the new INITBSS segment. The latter isn't cleared at any point so the constructors may use it to expose values to the main program. However they must make sure to always write the values as they are not pre-initialized.
Up to now static drivers were created via co65 from dynamic drivers. However there was an issue with that approach:
The dynamic drivers are "o65 simple files" which obligates that they start with the 'code' segment. However dynamic drivers need to start with the module header - which is written to. For dynamic drivers this isn't more than a conceptual issue because they are always contain a 'data' segment and may therefore only be loaded into writable memory.
However when dynamic drivers are converted to static drivers using co65 then that issue becomes a real problem as then the 'code' segment may end up in non-writable memory - and thus writing to the module header fails.
Instead of changing the way dynamic drivers work I opted to rather make static driver creation totally independent from dynamic drivers. This allows to place the module header in the 'data' segment (see 'module.mac').
This change was suppsed to fix the issue that the former JUMPTABLE is merked as 'ro' while it is actually written to in several scenarios. When drivers are converted using co65 and then compiled into ROMs the JUMPTABLE isn't copied to RAM and therefore the write operations in question fail.
However unfortunately I didn't succeed in changing that :-( Just setting the former JUMPTABLE to 'rw' broke the drivers. So I placed the DATA segment directly after the former JUMPTABLE segment. This made the drivers converted with co65 work again - obviously after changing libsrc/Makefile:235 from '--code-label' to '--data-label'. But the actual dynamic drivers still didn't work as the former JUMPTABLE wasn't placed as the beginning of the loaded file anymore. That effect could be changed by exchanging src/ld65/o65.c:1391 with src/ld65/o65.c:1394 but doing so broke the drivers again :-((
- make cursor character of text mode callback configurable
- change default cursor character of text mode callback from 'plus' to 'diamond'
- set P/M callback as default
Building the clean target in src or libsrc should only delete stuff created by the make in those directories. Having both separated allows the Travis CI build to replace the native binaries with cross built binaries while keeping everything else.
It seems more appropriate to trigger the inclusion of Makefile.inc via $TARGET (instead of $SRCDIR). This is btw. more consistent with extzp.s inclusion which is triggered via $TARGET too.
some time. Turn it back on when the mouse is moved again.
Since the polling interrupt runs at a rather high frequency (1kHz),
this saves many processor cycles when the mouse is inactive.
