stores, make sure the load or store that accesses the higher half does not have
an alignment that is larger than the offset from the original address.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@190318 91177308-0d34-0410-b5e6-96231b3b80d8
precision loads and stores as well as reg+imm double precision loads and stores.
Previously, expansion of loads and stores was done after register allocation,
but now it takes place during legalization. As a result, users will see double
precision stores and loads being emitted to spill and restore 64-bit FP registers.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@190235 91177308-0d34-0410-b5e6-96231b3b80d8
has hard float, when you compile the mips32 code you have to make sure
that it knows to compile any mips32 routines as hard float. I need to clean
up the way mips16 hard float is specified but I need to first think through
all the details. Mips16 always has a form of soft float, the difference being
whether the underlying hardware has floating point. So it's not really
necessary to pass the -soft-float to llvm since soft-float is always true
for mips16 by virtue of the fact that it will not register floating point
registers. By using this fact, I can simplify the way this is all handled.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@189690 91177308-0d34-0410-b5e6-96231b3b80d8
These intrinsics are legalized to V(ALL|ANY)_(NON)?ZERO nodes,
are matched as SN?Z_[BHWDV]_PSEUDO pseudo's, and emitted as
a branch/mov sequence to evaluate to 0 or 1.
Note: The resulting code is sub-optimal since it doesnt seem to be possible
to feed the result of an intrinsic directly into a brcond. At the moment
it uses (SETCC (VALL_ZERO $ws), 0, SETEQ) and similar which unnecessarily
evaluates the boolean twice.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@189478 91177308-0d34-0410-b5e6-96231b3b80d8
size of floating point registers is 64-bit.
Test case will be added when support for mfhc1 and mthc1 is added.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188847 91177308-0d34-0410-b5e6-96231b3b80d8
* msa SubtargetFeature
* registers
* ld.[bhwd], and st.[bhwd] instructions
Does not correctly prohibit use of both 32-bit FPU registers and MSA together.
Patch by Daniel Sanders
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188313 91177308-0d34-0410-b5e6-96231b3b80d8
Change SelectionDAG::getXXXNode() interfaces as well as call sites of
these functions to pass in SDLoc instead of DebugLoc.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182703 91177308-0d34-0410-b5e6-96231b3b80d8
and mips16 on a per function basis.
Because this patch is somewhat involved I have provide an overview of the
key pieces of it.
The patch is written so as to not change the behavior of the non mixed
mode. We have tested this a lot but it is something new to switch subtargets
so we don't want any chance of regression in the mainline compiler until
we have more confidence in this.
Mips32/64 are very different from Mip16 as is the case of ARM vs Thumb1.
For that reason there are derived versions of the register info, frame info,
instruction info and instruction selection classes.
Now we register three separate passes for instruction selection.
One which is used to switch subtargets (MipsModuleISelDAGToDAG.cpp) and then
one for each of the current subtargets (Mips16ISelDAGToDAG.cpp and
MipsSEISelDAGToDAG.cpp).
When the ModuleISel pass runs, it determines if there is a need to switch
subtargets and if so, the owning pointers in MipsTargetMachine are
appropriately changed.
When 16Isel or SEIsel is run, they will return immediately without doing
any work if the current subtarget mode does not apply to them.
In addition, MipsAsmPrinter needs to be reset on a function basis.
The pass BasicTargetTransformInfo is substituted with a null pass since the
pass is immutable and really needs to be a function pass for it to be
used with changing subtargets. This will be fixed in a follow on patch.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@179118 91177308-0d34-0410-b5e6-96231b3b80d8
derived class MipsSETargetLowering.
We shouldn't be generating madd/msub nodes if target is Mips16, since Mips16
doesn't have support for multipy-add/sub instructions.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@178404 91177308-0d34-0410-b5e6-96231b3b80d8
The new instructions have explicit register output operands and use table-gen
patterns instead of C++ code to do instruction selection.
Mips16's instructions are unaffected by this change.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@178403 91177308-0d34-0410-b5e6-96231b3b80d8
