Fixed an inappropriate use of BuildPairF64 when compiling for MIPS32 with FP64
which resulted in an impossible constraint on the register allocation. It now
uses BuildPairF64_64.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@195007 91177308-0d34-0410-b5e6-96231b3b80d8
accumulator instead of its sub-registers, $hi and $lo.
We need this change to prevent a mflo following a mtlo from reading an
unpredictable/undefined value, as shown in the following example:
mult $6, $7 // result of $6 * $7 is written to $lo and $hi.
mflo $2 // read lower 32-bit result from $lo.
mtlo $4 // write to $lo. the content of $hi becomes unpredictable.
mfhi $3 // read higher 32-bit from $hi, which has an unpredictable value.
I don't have a test case for this change that reliably reproduces the problem.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@192119 91177308-0d34-0410-b5e6-96231b3b80d8
precision loads and stores as well as reg+imm double precision loads and stores.
Previously, expansion of loads and stores was done after register allocation,
but now it takes place during legalization. As a result, users will see double
precision stores and loads being emitted to spill and restore 64-bit FP registers.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@190235 91177308-0d34-0410-b5e6-96231b3b80d8
The MSA control registers have been added as reserved registers,
and are only used via ISD::Copy(To|From)Reg. The intrinsics are lowered
into these nodes.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@189468 91177308-0d34-0410-b5e6-96231b3b80d8
point registers. We will need this register class later when we add
definitions for instructions mfhc1 and mthc1. Also, remove sub-register indices
sub_fpeven and sub_fpodd and use sub_lo and sub_hi instead.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188842 91177308-0d34-0410-b5e6-96231b3b80d8
load/store instructions defined. Previously, we were defining load/store
instructions for each pointer size (32 and 64-bit), but now we need just one
definition.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188830 91177308-0d34-0410-b5e6-96231b3b80d8
invalid instruction sequence.
Rather than emitting an int-to-FP move instruction and an int-to-FP conversion
instruction during instruction selection, we emit a pseudo instruction which gets
expanded post-RA. Without this change, register allocation can possibly insert a
floating point register move instruction between the two instructions, which is not
valid according to the ISA manual.
mtc1 $f4, $4 # int-to-fp move instruction.
mov.s $f2, $f4 # move contents of $f4 to $f2.
cvt.s.w $f0, $f2 # int-to-fp conversion.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182042 91177308-0d34-0410-b5e6-96231b3b80d8
This option is used when the user wants to avoid emitting double precision FP
loads and stores. Double precision FP loads and stores are expanded to single
precision instructions after register allocation.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@181718 91177308-0d34-0410-b5e6-96231b3b80d8
register.
- Define pseudo instructions which store or load ccond field of the DSP
control register.
- Emit the pseudos in MipsSEInstrInfo::storeRegToStack and loadRegFromStack.
- Expand the pseudos before callee-scan save.
- Emit instructions RDDSP or WRDSP to copy between ccond field and GPRs.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@180969 91177308-0d34-0410-b5e6-96231b3b80d8
Expand copy instructions between two accumulator registers before callee-saved
scan is done. Handle copies between integer GPR and hi/lo registers in
MipsSEInstrInfo::copyPhysReg. Delete pseudo-copy instructions that are not
needed.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@180827 91177308-0d34-0410-b5e6-96231b3b80d8
This patch initializes t9 to the handler address, but only if the relocation
model is pic. This handles the case where handler to which eh.return jumps
points to the start of the function.
Patch by Sasa Stankovic.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@178588 91177308-0d34-0410-b5e6-96231b3b80d8
physical register $r1 to $r0.
GNU disassembler recognizes an "or" instruction as a "move", and this change
makes the disassembled code easier to read.
Original patch by Reed Kotler.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@170655 91177308-0d34-0410-b5e6-96231b3b80d8
Sooooo many of these had incorrect or strange main module includes.
I have manually inspected all of these, and fixed the main module
include to be the nearest plausible thing I could find. If you own or
care about any of these source files, I encourage you to take some time
and check that these edits were sensible. I can't have broken anything
(I strictly added headers, and reordered them, never removed), but they
may not be the headers you'd really like to identify as containing the
API being implemented.
Many forward declarations and missing includes were added to a header
files to allow them to parse cleanly when included first. The main
module rule does in fact have its merits. =]
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@169131 91177308-0d34-0410-b5e6-96231b3b80d8
the temporary register that was used to load the immediate. Currently, it always
returns register $at, but this will change if, in the future, we decide to use
another register.
No changes in functionality.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@162417 91177308-0d34-0410-b5e6-96231b3b80d8
instructions that decrement and increment the stack pointer before and after a
call when the function does not have a reserved call frame.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@161093 91177308-0d34-0410-b5e6-96231b3b80d8
