RAM2E/CPLD/RAM2E-LCMXO2.v
2023-11-21 06:55:24 -05:00

834 lines
28 KiB
Verilog

module RAM2E(C14M, PHI1, LED,
nWE, nWE80, nEN80, nC07X,
Ain, Din, Dout, nDOE, Vout, nVOE,
CKE, nCS, nRAS, nCAS, nRWE,
BA, RA, RD, DQML, DQMH);
/* Clocks */
input C14M, PHI1;
/* SDRAM clock output */
output RCLK;
ODDRXE rclk_oddr(.D0(1'b0), .D1(1'b1),
.SCLK(C14M), .RST(1'b0), .Q(RCLK));
/* Control inputs */
input nWE, nWE80, nEN80, nC07X;
/* Activity LED */
reg LEDEN = 0;
output LED;
assign LED = !(!nEN80 && LEDEN && Ready);
/* Address Bus */
input [7:0] Ain; // Multiplexed DRAM address input
/* 6502 Data Bus */
input [7:0] Din; // 6502 data bus inputs
reg DOEEN = 0; // 6502 data bus output enable from state machine
output nDOE;
assign nDOE = !(!nEN80 && nWE && DOEEN); // 6502 data bus output enable
output reg [7:0] Dout; // 6502 data Bus output
/* Video Data Bus */
output nVOE;
assign nVOE = !(!PHI1); /// Video data bus output enable
output reg [7:0] Vout; // Video data bus
/* SDRAM */
output reg CKE = 0;
output nCS;
assign nCS = 0;
output reg nRAS = 1, nCAS = 1, nRWE = 1;
output reg [1:0] BA;
output reg [11:0] RA;
output reg DQML = 1, DQMH = 1;
wire RDOE = !nEN80 && !nWE80;
inout [7:0] RD;
assign RD[7:0] = RDOE ? Din[7:0] : 8'bZ;
/* RAMWorks Bank Register and Capacity Mask */
reg [7:0] RWBank = 0; // RAMWorks bank register
reg [7:0] RWMask = 0; // RAMWorks bank reg. capacity mask
reg RWSel = 0; // RAMWorks bank register select
reg CmdRWMaskSet = 0; // RAMWorks Mask register set flag
// Causes RWBank to be zeroed next RWSel access
//reg CmdSetRWBankFFMAX = 0;
//reg CmdSetRWBankFFSPI = 0;
reg CmdSetRWBankFFMXO2 = 0;
reg CmdSetRWBankFFLED = 0;
reg CmdLEDSet = 0;
reg CmdLEDGet = 0;
/* Command Sequence Detector */
reg [2:0] CS = 0; // Command sequence state
reg [2:0] CmdTout = 0; // Command sequence timeout
/* UFM Interface */
reg wb_rst;
reg wb_cyc_stb;
reg wb_req;
reg wb_we;
reg [7:0] wb_adr;
reg [7:0] wb_dati;
wire wb_ack;
wire [7:0] wb_dato;
wire ufm_irq;
REFB ufmefb(
.wb_clk_i(C14M),
.wb_rst_i(wb_rst),
.wb_cyc_i(wb_cyc_stb),
.wb_stb_i(wb_cyc_stb),
.wb_we_i(wb_we),
.wb_adr_i(wb_adr),
.wb_dat_i(wb_dati),
.wb_dat_o(wb_dato),
.wb_ack_o(wb_ack),
.wbc_ufm_irq(ufm_irq));
/* UFM State and User Command Triggers */
//reg CmdBitbangMAX = 0; // Set by user command. Loads UFM outputs next RWSel
//reg CmdBitbangSPI = 0;
reg CmdBitbangMXO2 = 0;
reg CmdExecMXO2 = 0;
//reg CmdPrgmMAX = 0; // Set by user command. Programs UFM
//reg CmdEraseMAX = 0; // Set by user command. Erases UFM
/* State Counters */
reg PHI1reg = 0; // Saved PHI1 at last rising clock edge
reg Ready = 0; // 1 if done with init sequence (S0) and enter S1-S15
reg [15:0] FS = 0; // Fast state counter
reg [3:0] S = 0; // IIe State counter
/* State Counters */
always @(posedge C14M) begin
// Increment fast state counter
FS <= FS+16'h0001;
// Synchronize Apple state counter to S1 when just entering PHI1
PHI1reg <= PHI1; // Save old PHI1
S <= (PHI1 && !PHI1reg && Ready) ? 4'h1 :
S==4'h0 ? 4'h0 :
S==4'hF ? 4'hF : S+4'h1;
end
/* UFM Control */
always @(posedge C14M) begin
if (S==4'h0) begin
if (FS[15:14]==2'b00) wb_rst <= 1'b1;
else if (FS[15:14]==2'b01) wb_rst <= 1'b0;
else if (FS[15:14]==2'b10) begin
wb_rst <= 1'b0;
if (wb_ack || (FS[7:0]==0)) wb_cyc_stb <= 0;
else if ((FS[7:0]==1) && wb_req) wb_cyc_stb <= 1;
case (FS[13:8])
0: begin // Open frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h80;
wb_req <= 1;
end 1: begin // Enable configuration interface - command
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h74;
wb_req <= 1;
end 2: begin // Enable configuration interface - operand 1/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h08;
wb_req <= 1;
end 3: begin // Enable configuration interface - operand 2/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 4: begin // Enable configuration interface - operand 3/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 5: begin // Close frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 6: begin // Open frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h80;
wb_req <= 1;
end 7: begin // Poll status register - command
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h3C;
wb_req <= 1;
end 8: begin // Poll status register - operand 1/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 9: begin // Poll status register - operand 2/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 10: begin // Poll status register - operand 3/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 11, 12, 13, 14: begin // Read status register 1-4
wb_we <= 1'b0;
wb_adr[7:0] <= 8'h73;
wb_dati[7:0] <= 8'h3C;
wb_req <= 1;
end 15: begin // Close frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 16: begin // Open frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h80;
wb_req <= 1;
end 17: begin // Set UFM address - command
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'hB4;
wb_req <= 1;
end 18: begin // Set UFM address - operand 1/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 19: begin // Set UFM address - operand 2/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 20: begin // Set UFM address - operand 3/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 21: begin // Set UFM address - data 1/4
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h40;
wb_req <= 1;
end 22: begin // Set UFM address - data 2/4
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 23: begin // Set UFM address - data 3/4
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 24: begin // Set UFM address - data 4/4
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 190;
wb_req <= 1;
end 25: begin // Close frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 26: begin // Open frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h80;
wb_req <= 1;
end 27: begin // Read UFM page - command
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'hCA;
wb_req <= 1;
end 28: begin // Read UFM page - operand 1/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h10;
wb_req <= 1;
end 29: begin // Read UFM page - operand 2/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 30: begin // Read UFM page - operand 3/3
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h01;
wb_req <= 1;
end 31: begin // Read UFM page - data 0
wb_we <= 1'b0;
wb_adr[7:0] <= 8'h73;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
if (wb_ack) RWMask[7:0] <= wb_dato[7:0];
end 32: begin // Read UFM page - data 1
wb_we <= 1'b0;
wb_adr[7:0] <= 8'h73;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
if (wb_ack) LEDEN <= wb_dato[0];
end 33, 34,
35, 36, 37, 38,
39, 40, 41, 42,
43, 44, 45, 46: begin // Read UFM page - data 2-15
wb_we <= 1'b0;
wb_adr[7:0] <= 8'h73;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 47: begin // Close frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 48: begin // Open frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h80;
wb_req <= 1;
end 49: begin // Disable configuration interface - command
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h26;
wb_req <= 1;
end 50: begin // Disable configuration interface - operand 1/2
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 51: begin // Disable configuration interface - operand 2/2
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 52: begin // Close frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end 53: begin // Open frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h80;
wb_req <= 1;
end 54: begin // Bypass - command
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h71;
wb_dati[7:0] <= 8'hFF;
wb_req <= 1;
end 55: begin // Close frame
wb_we <= 1'b1;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h00;
wb_req <= 1;
end default: begin
wb_we <= 1'b0;
wb_adr[7:0] <= 8'h70;
wb_dati[7:0] <= 8'h00;
wb_req <= 0;
end
endcase
end else begin
wb_rst <= 1'b0;
wb_cyc_stb <= 1'b0;
wb_req <= 1'b0;
wb_we <= 1'b0;
wb_adr[7:0] <= 8'h00;
wb_dati[7:0] <= 8'h00;
end
end else begin
// UFM bitbang control
wb_rst <= 1'b0;
wb_req <= 1'b0;
if (RWSel && S==4'hC) begin
// LED control
if (CmdLEDSet) LEDEN <= Din[0];
// Set capacity mask
if (CmdRWMaskSet) RWMask[7:0] <= {Din[7], ~Din[6:0]};
// Set EFB address
if (CmdBitbangMXO2) begin
wb_adr[7:0] <= Din[7:0];
wb_dati[7:0] <= wb_adr[7:0];
end
// Excecute EFB R/W cycle
if (CmdExecMXO2) begin
wb_we <= Din[0];
wb_cyc_stb <= 1;
end else if (wb_ack) wb_cyc_stb <= 0;
end
end
end
/* SDRAM Control */
always @(posedge C14M) begin
if (S==4'h0) begin
// SDRAM initialization
if (FS[15:0]==16'hFFC0) begin
// Precharge All
nCS <= 1'b0;
nRAS <= 1'b0;
nCAS <= 1'b1;
nRWE <= 1'b0;
RA[10] <= 1'b1; // "all"
end else if (FS[15:4]==16'hFFD && FS[0]==1'b0) begin // Repeat 8x
// Auto-refresh
nCS <= 1'b0;
nRAS <= 1'b0;
nCAS <= 1'b0;
nRWE <= 1'b1;
RA[10] <= 1'b0;
end else if (FS[15:0]==16'hFFE8) begin
// Set Mode Register
nCS <= 1'b0;
nRAS <= 1'b0;
nCAS <= 1'b0;
nRWE <= 1'b0;
RA[10] <= 1'b0; // Reserved in mode register
end else if (FS[15:4]==12'hFFF && FS[0]==1'b0) begin // Repeat 8x
// Auto-refresh
nCS <= 1'b0;
nRAS <= 1'b0;
nCAS <= 1'b0;
nRWE <= 1'b1;
RA[10] <= 1'b0;
end else begin // Otherwise send no-op
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
RA[10] <= 1'b0;
end
// Enable SDRAM clock after 65,280 cycles (~4.56ms)
CKE <= FS[15:8] == 8'hFF;
// Mode register contents
BA[1:0] <= 2'b00; // Reserved
RA[11] <= 1'b0; // Reserved
// RA[10] set above ^
RA[9] <= 1'b1; // "1" for single write mode
RA[8] <= 1'b0; // Reserved
RA[7] <= 1'b0; // "0" for not test mode
RA[6:4] <= 3'b010; // "2" for CAS latency 2
RA[3] <= 1'b0; // "0" for sequential burst (not used)
RA[2:0] <= 3'b000; // "0" for burst length 1 (no burst)
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Inhibit data bus output
DOEEN <= 1'b0;
// Begin normal operation after 128k init cycles (~9.15ms)
if (FS == 16'hFFFF) Ready <= 1'b1;
end else if (S==4'h1) begin
// Enable clock
CKE <= 1'b1;
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Inhibit data bus output
DOEEN <= 1'b0;
end else if (S==4'h2) begin
// Enable clock
CKE <= 1'b1;
// Activate
nCS <= 1'b0;
nRAS <= 1'b0;
nCAS <= 1'b1;
nRWE <= 1'b1;
// SDRAM bank 0, high-order row address is 0
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Row address is as previously latched
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Inhibit data bus output
DOEEN <= 1'b0;
end else if (S==4'h3) begin
// Enable clock
CKE <= 1'b1;
// Read
nCS <= 1'b0;
nRAS <= 1'b1;
nCAS <= 1'b0;
nRWE <= 1'b1;
// SDRAM bank 0, RA[11,9:8] don't care
BA[1:0] <= 2'b00;
RA[11] <= 1'b0;
RA[10] <= 1'b1; // (A10 set to auto-precharge)
RA[9] <= 1'b0;
RA[8] <= 1'b0;
// Latch column address for read command
RA[7:0] <= Ain[7:0];
// Read low byte (high byte is +4MB in ramworks)
DQML <= 1'b0;
DQMH <= 1'b1;
// Inhibit data bus output
DOEEN <= 1'b0;
end else if (S==4'h4) begin
// Enable clock
CKE <= 1'b1;
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Inhibit data bus output
DOEEN <= 1'b0;
end else if (S==4'h5) begin
// Enable clock
CKE <= 1'b1;
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Inhibit data bus output
DOEEN <= 1'b0;
end else if (S==4'h6) begin
// Enable clock
CKE <= 1'b1;
if (FS[5:4]==0) begin
// Auto-refresh
nCS <= 1'b0;
nRAS <= 1'b0;
nCAS <= 1'b0;
nRWE <= 1'b1;
end else begin
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
end
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Inhibit data bus output
DOEEN <= 1'b0;
end else if (S==4'h7) begin
// Enable clock
CKE <= 1'b1;
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Latch row address for activate command
RA[7:0] <= Ain[7:0];
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Inhibit data bus output
DOEEN <= 1'b0;
end else if (S==4'h8) begin
// Enable clock if '245 output enabled
CKE <= !nEN80;
// Activate if '245 output enabled
nCS <= nEN80;
nRAS <= 1'b0;
nCAS <= 1'b1;
nRWE <= 1'b1;
// SDRAM bank, RA[11:8] determine by RamWorks bank
BA[1:0] <= RWBank[5:4];
RA[11:8] <= RWBank[3:0];
// Row address is as previously latched
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Inhibit data bus output
DOEEN <= 1'b0;
end else if (S==4'h9) begin
// Enable clock if '245 output enabled
CKE <= !nEN80;
// Read/Write if '245 output enabled
nCS <= nEN80;
nRAS <= 1'b1;
nCAS <= 1'b0;
nRWE <= nWE80;
// SDRAM bank still determined by RamWorks, RA[11,9:8] don't care
BA[1:0] <= RWBank[5:4];
RA[11] <= 1'b0;
RA[10] <= 1'b1; // (A10 set to auto-precharge)
RA[9] <= 1'b0;
RA[8] <= RWBank[7];
// Latch column address for R/W command
RA[7:0] <= Ain[7:0];
// Latch RAMWorks low nybble write select using old row address
RWSel <= RA[0] && !RA[3] && !nWE && !nC07X;
// Mask according to RAMWorks bank (high byte is +4MB)
DQML <= RWBank[6];
DQMH <= !RWBank[6];
// Inhibit data bus output
DOEEN <= 1'b0;
end else if (S==4'hA) begin
// Enable clock if '245 output enabled
CKE <= !nEN80;
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Inhibit data bus output
DOEEN <= 1'b0;
end else if (S==4'hB) begin
// Disable clock
CKE <= 1'b0;
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Enable data bus output
DOEEN <= 1'b1;
end else if (S==4'hC) begin
// Disable clock
CKE <= 1'b0;
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Enable data bus output
DOEEN <= 1'b1;
// RAMWorks Bank Register Select
if (RWSel) begin
// Latch RAMWorks bank if accessed
if (CmdSetRWBankFFLED ||
//CmdSetRWBankFFMAX ||
//CmdSetRWBankFFSPI ||
CmdSetRWBankFFMXO2 ||
(CmdLEDGet && LEDEN)) RWBank <= 8'hFF;
else RWBank <= Din[7:0] & {RWMask[7], ~RWMask[6:0]};
// Recognize command sequence and advance CS state
if ((CS==3'h0 && Din[7:0]==8'hFF) ||
(CS==3'h1 && Din[7:0]==8'h00) ||
(CS==3'h2 && Din[7:0]==8'h55) ||
(CS==3'h3 && Din[7:0]==8'hAA) ||
(CS==3'h4 && Din[7:0]==8'hC1) ||
(CS==3'h5 && Din[7:0]==8'hAD) ||
CS==3'h6 || CS==3'h7) CS <= CS+3'h1;
else CS <= 0; // Back to beginning if it's not right
if (CS==3'h6) begin // Recognize and submit command in CS6
//CmdSetRWBankFFMAX <= Din[7:0]==8'hFF;
//CmdSetRWBankFFSPI <= Din[7:0]==8'hFE;
CmdSetRWBankFFMXO2 <= Din[7:0]==8'hFD;
CmdSetRWBankFFLED <= Din[7:0]==8'hF0;
CmdRWMaskSet <= Din[7:0]==8'hE0;
CmdLEDSet <= Din[7:0]==8'hE2;
CmdLEDGet <= Din[7:0]==8'hE3;
//CmdBitbangMAX <= Din[7:0]==8'hEA;
//CmdBitbangSPI <= Din[7:0]==8'hEB;
CmdBitbangMXO2 <= Din[7:0]==8'hEC;
CmdExecMXO2 <= Din[7:0]==8'hED;
//if (Din[7:0]==8'hEE) CmdEraseMAX <= 1;
//if (Din[7:0]==8'hEF) CmdPrgmMAX <= 1;
end else begin // Reset command triggers
//CmdSetRWBankFFMAX <= 0;
//CmdSetRWBankFFSPI <= 0;
CmdSetRWBankFFMXO2 <= 0;
CmdSetRWBankFFLED <= 0;
CmdRWMaskSet <= 0;
CmdLEDSet <= 0;
CmdLEDGet <= 0;
//CmdBitbangMAX <= 0;
//CmdBitbangSPI <= 0;
CmdBitbangMXO2 <= 0;
CmdExecMXO2 <= 0;
end
CmdTout <= 0; // Reset command timeout if RWSel accessed
end else begin
CmdTout <= CmdTout+3'h1; // Increment command timeout
// If command sequence times out, reset sequence state
if (CmdTout==3'h7) CS <= 0;
end
end else if (S==4'hD) begin
// Disable clock
CKE <= 1'b0;
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Enable data bus output
DOEEN <= 1'b1;
end else if (S==4'hE) begin
// Disable clock
CKE <= 1'b0;
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Latch row address for next video read
RA[7:0] <= Ain[7:0];
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Enable data bus output
DOEEN <= 1'b1;
end else if (S==4'hF) begin
// Disable clock
CKE <= 1'b0;
// NOP
nCS <= 1'b1;
nRAS <= 1'b1;
nCAS <= 1'b1;
nRWE <= 1'b1;
// Don't care bank, RA[11:8]
BA[1:0] <= 2'b00;
RA[11:8] <= 4'b0000;
// Latch row address for next video read
RA[7:0] <= Ain[7:0];
// Mask everything
DQML <= 1'b1;
DQMH <= 1'b1;
// Enable data bus output
DOEEN <= 1'b1;
end
end
always @(negedge C14M) begin
// Latch video and read data outputs
if (S==4'h6) Vout[7:0] <= RD[7:0];
if (S==4'hC) Dout[7:0] <= RD[7:0];
end
endmodule