PAR: Place And Route Diamond (64-bit) 3.12.1.454.
Copyright (c) 1991-1994 by NeoCAD Inc. All rights reserved.
Copyright (c) 1995 AT&T Corp.   All rights reserved.
Copyright (c) 1995-2001 Lucent Technologies Inc.  All rights reserved.
Copyright (c) 2001 Agere Systems   All rights reserved.
Copyright (c) 2002-2020 Lattice Semiconductor Corporation,  All rights reserved.
Sat Jan 06 06:25:01 2024

C:/lscc/diamond/3.12/ispfpga\bin\nt64\par -f RAM2GS_LCMXO256C_impl1.p2t
RAM2GS_LCMXO256C_impl1_map.ncd RAM2GS_LCMXO256C_impl1.dir
RAM2GS_LCMXO256C_impl1.prf -gui -msgset
//Mac/iCloud/Repos/RAM2GS/CPLD/LCMXO256C/promote.xml


Preference file: RAM2GS_LCMXO256C_impl1.prf.

Cost Table Summary
Level/       Number       Worst        Timing       Worst        Timing       Run          NCD
Cost [ncd]   Unrouted     Slack        Score        Slack(hold)  Score(hold)  Time         Status
----------   --------     -----        ------       -----------  -----------  ----         ------
5_1   *      0            6.770        0            0.273        0            11           Completed
* : Design saved.

Total (real) run time for 1-seed: 11 secs 

par done!

Note: user must run 'Trace' for timing closure signoff.

Lattice Place and Route Report for Design "RAM2GS_LCMXO256C_impl1_map.ncd"
Sat Jan 06 06:25:01 2024


Best Par Run
PAR: Place And Route Diamond (64-bit) 3.12.1.454.
Command Line: par -w -l 5 -i 6 -t 1 -c 0 -e 0 -gui -msgset //Mac/iCloud/Repos/RAM2GS/CPLD/LCMXO256C/promote.xml -exp parUseNBR=1:parCDP=0:parCDR=0:parPathBased=OFF:parASE=1 RAM2GS_LCMXO256C_impl1_map.ncd RAM2GS_LCMXO256C_impl1.dir/5_1.ncd RAM2GS_LCMXO256C_impl1.prf
Preference file: RAM2GS_LCMXO256C_impl1.prf.
Placement level-cost: 5-1.
Routing Iterations: 6

Loading design for application par from file RAM2GS_LCMXO256C_impl1_map.ncd.
Design name: RAM2GS
NCD version: 3.3
Vendor:      LATTICE
Device:      LCMXO256C
Package:     TQFP100
Performance: 3
Loading device for application par from file 'mj5g10x6.nph' in environment: C:/lscc/diamond/3.12/ispfpga.
Package Status:                     Final          Version 1.19.
Performance Hardware Data Status: Version 1.124.
License checked out.


Ignore Preference Error(s):  True

Device utilization summary:

   PIO (prelim)      67/79           84% used
                     67/78           85% bonded
   SLICE             76/128          59% used



Number of Signals: 266
Number of Connections: 681

Pin Constraint Summary:
   67 out of 67 pins locked (100% locked).

The following 2 signals are selected to use the primary clock routing resources:
    RCLK_c (driver: RCLK, clk load #: 32)
    PHI2_c (driver: PHI2, clk load #: 14)

The following 1 signal is selected to use the secondary clock routing resources:
    nCRAS_c (driver: nCRAS, clk load #: 8, sr load #: 0, ce load #: 0)

No signal is selected as Global Set/Reset.
Starting Placer Phase 0.
......
Finished Placer Phase 0.  REAL time: 0 secs 

Starting Placer Phase 1.
.................
Placer score = 783987.
Finished Placer Phase 1.  REAL time: 9 secs 

Starting Placer Phase 2.
.
Placer score =  783552
Finished Placer Phase 2.  REAL time: 10 secs 



Clock Report

Global Clock Resources:
  CLK_PIN    : 1 out of 4 (25%)
  General PIO: 1 out of 80 (1%)

Global Clocks:
  PRIMARY "RCLK_c" from comp "RCLK" on CLK_PIN site "86 (PT4A)", clk load = 32
  PRIMARY "PHI2_c" from comp "PHI2" on PIO site "39 (PB3D)", clk load = 14
  SECONDARY "nCRAS_c" from comp "nCRAS" on PIO site "43 (PB4A)", clk load = 8, ce load = 0, sr load = 0

  PRIMARY  : 2 out of 4 (50%)
  SECONDARY: 1 out of 4 (25%)




I/O Usage Summary (final):
   67 out of 79 (84.8%) PIO sites used.
   67 out of 78 (85.9%) bonded PIO sites used.
   Number of PIO comps: 67; differential: 0.
   Number of Vref pins used: 0.

I/O Bank Usage Summary:
+----------+----------------+------------+------------+------------+
| I/O Bank | Usage          | Bank Vccio | Bank Vref1 | Bank Vref2 |
+----------+----------------+------------+------------+------------+
| 0        | 36 / 41 ( 87%) | 3.3V       | -          | -          |
| 1        | 31 / 37 ( 83%) | 3.3V       | -          | -          |
+----------+----------------+------------+------------+------------+

Total placer CPU time: 9 secs 

Dumping design to file RAM2GS_LCMXO256C_impl1.dir/5_1.ncd.

0 connections routed; 681 unrouted.
Starting router resource preassignment
WARNING - par: The driver of primary clock net PHI2_c is not placed on one of the PIO sites dedicated for primary clocks.  This primary clock will be routed to a H-spine through general routing resource and may suffer from excessive delay or skew.
WARNING - par: The driver of secondary clock net nCRAS_c is not placed on one of the PIO sites dedicated for secondary clocks.  This secondary clock will be routed through general routing resource and may suffer from excessive delay or skew.

WARNING - par: The following clock signals will be routed by using generic routing resource and may suffer from excessive delay and/or skew.
   Signal=nCCAS_c loads=8 clock_loads=4

Completed router resource preassignment. Real time: 10 secs 

Start NBR router at 06:25:11 01/06/24

*****************************************************************
Info: NBR allows conflicts(one node used by more than one signal)
      in the earlier iterations. In each iteration, it tries to  
      solve the conflicts while keeping the critical connections 
      routed as short as possible. The routing process is said to
      be completed when no conflicts exist and all connections   
      are routed.                                                
Note: NBR uses a different method to calculate timing slacks. The
      worst slack and total negative slack may not be the same as
      that in TRCE report. You should always run TRCE to verify  
      your design.                                               
*****************************************************************

Start NBR special constraint process at 06:25:11 01/06/24

Start NBR section for initial routing at 06:25:11 01/06/24
Level 1, iteration 1
0(0.00%) conflict; 593(87.08%) untouched conns; 0 (nbr) score; 
Estimated worst slack/total negative slack<setup>: 7.904ns/0.000ns; real time: 10 secs 
Level 2, iteration 1
0(0.00%) conflict; 592(86.93%) untouched conns; 0 (nbr) score; 
Estimated worst slack/total negative slack<setup>: 8.083ns/0.000ns; real time: 10 secs 
Level 3, iteration 1
0(0.00%) conflict; 591(86.78%) untouched conns; 0 (nbr) score; 
Estimated worst slack/total negative slack<setup>: 7.994ns/0.000ns; real time: 10 secs 
Level 4, iteration 1
13(0.11%) conflicts; 0(0.00%) untouched conn; 0 (nbr) score; 
Estimated worst slack/total negative slack<setup>: 7.278ns/0.000ns; real time: 10 secs 

Info: Initial congestion level at 75% usage is 0
Info: Initial congestion area  at 75% usage is 0 (0.00%)

Start NBR section for normal routing at 06:25:11 01/06/24
Level 4, iteration 1
7(0.06%) conflicts; 0(0.00%) untouched conn; 0 (nbr) score; 
Estimated worst slack/total negative slack<setup>: 6.770ns/0.000ns; real time: 10 secs 
Level 4, iteration 2
4(0.03%) conflicts; 0(0.00%) untouched conn; 0 (nbr) score; 
Estimated worst slack/total negative slack<setup>: 6.770ns/0.000ns; real time: 10 secs 
Level 4, iteration 3
0(0.00%) conflict; 0(0.00%) untouched conn; 0 (nbr) score; 
Estimated worst slack/total negative slack<setup>: 6.770ns/0.000ns; real time: 10 secs 

Start NBR section for setup/hold timing optimization with effort level 3 at 06:25:11 01/06/24

Start NBR section for re-routing at 06:25:11 01/06/24
Level 4, iteration 1
0(0.00%) conflict; 0(0.00%) untouched conn; 0 (nbr) score; 
Estimated worst slack/total negative slack<setup>: 6.770ns/0.000ns; real time: 10 secs 

Start NBR section for post-routing at 06:25:11 01/06/24

End NBR router with 0 unrouted connection

NBR Summary
-----------
  Number of unrouted connections : 0 (0.00%)
  Number of connections with timing violations : 0 (0.00%)
  Estimated worst slack<setup> : 6.770ns
  Timing score<setup> : 0
-----------
Notes: The timing info is calculated for SETUP only and all PAR_ADJs are ignored.



WARNING - par: The following clock signals will be routed by using generic routing resource and may suffer from excessive delay and/or skew.
   Signal=nCCAS_c loads=8 clock_loads=4

Total CPU time 10 secs 
Total REAL time: 11 secs 
Completely routed.
End of route.  681 routed (100.00%); 0 unrouted.

Hold time timing score: 0, hold timing errors: 0

Timing score: 0 

Dumping design to file RAM2GS_LCMXO256C_impl1.dir/5_1.ncd.


All signals are completely routed.


PAR_SUMMARY::Run status = Completed
PAR_SUMMARY::Number of unrouted conns = 0
PAR_SUMMARY::Worst  slack<setup/<ns>> = 6.770
PAR_SUMMARY::Timing score<setup/<ns>> = 0.000
PAR_SUMMARY::Worst  slack<hold /<ns>> = 0.273
PAR_SUMMARY::Timing score<hold /<ns>> = 0.000
PAR_SUMMARY::Number of errors = 0

Total CPU  time to completion: 10 secs 
Total REAL time to completion: 11 secs 

par done!

Note: user must run 'Trace' for timing closure signoff.

Copyright (c) 1991-1994 by NeoCAD Inc. All rights reserved.
Copyright (c) 1995 AT&T Corp.   All rights reserved.
Copyright (c) 1995-2001 Lucent Technologies Inc.  All rights reserved.
Copyright (c) 2001 Agere Systems   All rights reserved.
Copyright (c) 2002-2020 Lattice Semiconductor Corporation,  All rights reserved.