TommyPROM/docs/hardware.md

title	description	has_children	nav_order
Hardware Design	TommyPROM Arduino 28C256 programmer hardware design	false	3

Hardware Design

Basic Hardware Version

The hardware uses an Arduino to write data and to toggle control lines with the appropriate timing to access the PROM. A pair of 74LS164 serial to parallel shift registers latch the address lines. Use of the shift registers allows the Arduino to control up to 16 address lines using only 3 output ports. This design will read and program the 28C series chips and can read most other parallel ROM chip families.

The basic circuit is as follows:

• Pins D2..D9 are wired to the data lines on the target PROM.
• Pins A0..A2 are wired to the WE, CE, and OE control lines on the target PROM.
• Pins A3..A5 control shift registers to produce the address lines.
• Pins D10..D12 control A16..A18 for chips larger than 64K bytes.

Note that the existing design uses 74LS164 shift registers, but another 8-bit parallel out shift register, like the 74LS595, could be used instead with some pin changes.

When using the 74LS595 instead of the 74LS164, there is an additional output latch that needs to be pulsed to put the contents of the shift register on the output lines. The code supports this by uncommenting the #define SHIFT_REGISTER_IS_595 line in Configure.h. The D13 line from the Arduino controls the RCLK latch on the '595. The table below shows the connections when using either the 74LS164 or the 74LS595 for the address shift registers. USR refers to the Upper Shift Register (A₈..A₁₅) and LSR refers to the Lower Shift Register (A₀..A₇).

Arduino	74LS164	74LS595
A0	ROM WE	ROM WE
A1	ROM CE	ROM CE
A2	ROM OE	ROM OE
A3	USR CLK	USR SRCLK
A4	LSR CLK	LSR SRCLK
A51	LSR+USR A	LSR+USR SER
D2..D9	ROM D0..D7	ROM D0..D7
D10..D122	ROM A16..A18	ROM A16..A18
D133	--	LSR+USR RCLK

Notes:

1. The data pin on A5 is connected to both the Upper Shift Register (USR) and the Lower Shift Register (LSR).
2. The upper address lines are not needed for 28C64 and 28C256 chips, but are used for larger chips like the 27C040.
3. The D13 pin controls the output register on the '595 shift registers. The code for this must be enabled in Configure.h. This pin is not connected when using the 74LS164.

The two shift registers can produce a sixteen bit address, although the 28C256 only needs 15 addresses. Chips larger than 64K are supported by using the shift registers for A₀..A₁₅ and connecting Arduino pins D10..D12 to the chip's A₁₆..A₁₈

NOTE: The schematic does not show the Vcc and ground pins for the 74LS164 shift registers. These must be connected to +5 and ground, respectively. It is also good practice to place a decoupling capacitor (0.1uF or 0.01uF is good) on the power rails near the Vcc connections.

Ben Eater EEPROM Programmer

If you are here because you built the Ben Eater EEPROM Programmer, note that the designs are similar, but the TommyPROM code will not run on that hardware without some significant changes. If you just need to unlock the Software Data Protection (SDP) on a chip, then see the unlock-ben-eater-hardware sketch for a solution. That sketch is purpose-built to run on the Ben Eater hardware directly and it will not work with the TommyPROM hardware.

If you want the functionality of the TommyPROM software on the Ben Eater hardware, the easiest path is probably to modify the hardware to match the TommyPROM software rather than trying to change the pin assignments in software. There are a few reasons for this:

• The Ben Eater hardware uses D13 to control the ROM's Write Enable pin and it ties the Chip Enable pin to always be active. The D13 pin is connected to the Arduino's built-in LED, which blinks at boot. This means that the chip is likely writing some random data at boot time. This isn't a problem for the Ben Eater sketches, because they always write their own data to the chip anyway. One use of TommyPROM is to just read data from a chip, so a random write on boot would be bad.
• The OE pin is controlled by the Address shift registers. This doesn't work well with the modular architecture of TommyPROM and it definitely would not work with 74LS164s because it would toggle the OE pin as new addresses are shifted in.
• The direct port write software is a bit complicated and is more difficult to change than just renaming a few pin #defines. This was done for performance reasons, particularly for the SDP timing, but it means that the code is not easy to change.

Changing the hardware is fairly straightforward. The data lines move 3 pins from D5..D12 down to D2..D9. Most of the ROM and shift register control lines move over to the A0..A5 pins. The upper shift register is controlled directly from the Arduino instead of being connected to the overflow of the lower shift register. All of the connections are in the chart in the section above.

Intel 8755A Hardware Version

The Intel 8755A uses a multiplexed data and address bus, plus 3 additional address lines. Most Arduino hardware has enough pins to support this directly, so no additional hardware is needed for addressing. An Arduino pin is also used to drive the ALE latch pin.

The 8755A requires the Vdd pin to be be switched between 5V and 25V during the programming of each byte. A simple transistor circuit is used for this. No voltage regulator circuit is present here for the programming voltage. Because this is designed as a quickly assembled hardware design, a triple output bench supply was used to provide the 25.5V, 5.5V and 5V outputs.

Eagle-format schematics can be downloaded from the hardware project page.