afterburner/afterburner.ino
2024-04-03 22:16:46 +01:00

3071 lines
80 KiB
C++

/*
(banner font: aciiart.eu)
_____________________________________________________________
| _ __ _ _ \
| / \ / _| |_ ___ _ _| |__ _ _ _ __ ___ ___ _ _ |\
| / _ \| |_| '_/ _ \| '_/ '_ \| | | | '_/ _ \/ _ \| '_/ ||
| / ___ \ _| |_| __/| | | |_) | |_| | | | | | | __/| | ||
| /_/ \_\| \__\___||_| |____/\___,_|_| |_| |_|___||_| ||
\_____________________________________________________________||
'------------------------------------------------------------'
Afterburner: GAL IC Programmer for Arduino by -= olin =-
Based on ATFblast 3.1 by Bruce Abbott
http://www.bhabbott.net.nz/atfblast.html
Based on GALBLAST by Manfred Winterhoff
http://www.armory.com/%7Erstevew/Public/Pgmrs/GAL/_ClikMe1st.htm
Based on GALmate by Yorck Thiele
https://www.ythiee.com/2021/06/06/galmate-hardware/
Supports:
* National GAL16V8
* Lattice GAL16V8A, GAL16V8B, GAL16V8D
* Lattice GAL22V10B
* Lattice GAL20V8
* Atmel ATF16V8B, ATF16V8C, ATF22V10B, ATF22V10CQZ
Requires:
* afterburner PC program to upload JED fuse map, erase, read etc.
* simple programming circuit. See: https://github.com/ole00/afterburner
* 2024-02-02 Fixed: Command 'B9' (Calibration Offset = 0,25V) doesn't work
Note: Also requires elimination of a in the PC program afterburner.c
Added: 10.0V measurement in measureVppValues(()
*/
#define VERSION "0.5.8"
//#define DEBUG_PES
//#define DEBUG_VERIFY
//ARDUINO UNO pin mapping
// GAL PIN NAME | ARDUINO UNO PIN NUMBER
//programing voltage control pin
#define PIN_VPP 11
#define PIN_SDOUT 12
#define PIN_STROBE 13
#define PIN_PV 9
#define PIN_SDIN 8
#define PIN_RA0 10
#define PIN_RA1 2
#define PIN_RA2 3
#define PIN_RA3 4
#define PIN_RA4 5
#define PIN_RA5 6
#define PIN_SCLK 7
// pin multiplex: ZIF_PIN <----> ARDUINO PIN or Shift register pin (0b1xxx)
#define PIN_ZIF3 2
#define PIN_ZIF4 0b1
#define PIN_ZIF5 0b1000
#define PIN_ZIF6 0b100
#define PIN_ZIF7 0b10
#define PIN_ZIF8 5
#define PIN_ZIF9 6
#define PIN_ZIF10 7
#define PIN_ZIF11 8
#define PIN_ZIF13 12
#define PIN_ZIF14 11
#define PIN_ZIF15 10
#define PIN_ZIF16 9
#define PIN_ZIF20 0b100000
#define PIN_ZIF21 0b10000
#define PIN_ZIF22 4
#define PIN_ZIF23 3
#define PIN_ZIF_GND_CTRL 13
//A0: VPP sense
//A3: DIGI_POT CS
#define PIN_SHR_EN A1
#define PIN_SHR_CS A2
//clk and dat is shared SPI bus
#define PIN_SHR_CLK A4
#define PIN_SHR_DAT A5
#define COMMAND_NONE 0
#define COMMAND_UNKNOWN 1
#define COMMAND_IDENTIFY_PROGRAMMER '*'
#define COMMAND_HELP 'h'
#define COMMAND_UPLOAD 'u'
#define COMMAND_DEBUG 'd'
#define COMMAND_READ_PES 'p'
#define COMMAND_WRITE_PES 'P'
#define COMMAND_READ_FUSES 'r'
#define COMMAND_WRITE_FUSES 'w'
#define COMMAND_VERIFY_FUSES 'v'
#define COMMAND_ERASE_GAL 'c'
#define COMMAND_ERASE_GAL_ALL '~'
#define COMMAND_UTX '#'
#define COMMAND_ECHO 'e'
#define COMMAND_TEST_VOLTAGE 't'
#define COMMAND_SET_GAL_TYPE 'g'
#define COMMAND_ENABLE_CHECK_TYPE 'f'
#define COMMAND_DISABLE_CHECK_TYPE 'F'
#define COMMAND_ENABLE_SECURITY 's'
#define COMMAND_ENABLE_APD 'z'
#define COMMAND_DISABLE_APD 'Z'
#define COMMAND_MEASURE_VPP 'm'
#define COMMAND_CALIBRATE_VPP 'b'
#define COMMAND_CALIBRATION_OFFSET 'B'
#define COMMAND_JTAG_PLAYER 'j'
#define READGAL 0
#define VERIFYGAL 1
#define READPES 2
#define SCLKTEST 3
#define WRITEGAL 4
#define ERASEGAL 5
#define ERASEALL 6
#define BURNSECURITY 7
#define WRITEPES 8
#define VPPTEST 9
#define INIT 100
//check GAL type before starting an operation
#define FLAG_BIT_TYPE_CHECK (1 << 0)
// ATF16V8C flavour
#define FLAG_BIT_ATF16V8C (1 << 1)
// Keep the power-down feature enabled for ATF C GALs
#define FLAG_BIT_APD (1 << 2)
// contents of pes[3]
// Atmel PES is text string eg. 1B8V61F1 or 3Z01V22F1
// ^ ^
#define LATTICE 0xA1
#define NATIONAL 0x8F
#define SGSTHOMSON 0x20
#define ATMEL16 'V'
#define ATMEL22 '1'
#define ATMEL750 'C'
typedef enum {
UNKNOWN,
GAL16V8,
GAL18V10,
GAL20V8,
GAL20RA10,
GAL20XV10,
GAL22V10,
GAL26CV12,
GAL26V12,
GAL6001,
GAL6002,
ATF16V8B,
ATF20V8B,
ATF22V10B,
ATF22V10C,
ATF750C,
LAST_GAL_TYPE //dummy
} GALTYPE;
typedef enum {
PINOUT_UNKNOWN,
PINOUT_16V8,
PINOUT_18V10,
PINOUT_20V8,
PINOUT_22V10,
PINOUT_600,
} PINOUT;
#define BIT_NONE 0
#define BIT_ZERO 1
#define BIT_ONE 2
// config bit numbers
#define CFG_BASE_16 2048
#define CFG_BASE_18 3456
#define CFG_BASE_20 2560
#define CFG_BASE_20RA 3200
#define CFG_BASE_20XV 1600
#define CFG_BASE_22 5808
#define CFG_BASE_26CV 6344
#define CFG_BASE_26V 7800
#define CFG_BASE_600 8154
#define CFG_BASE_750 14364
#define CFG_STROBE_ROW 0
#define CFG_SET_ROW 1
#define CFG_STROBE_ROW2 3
// Atmel power-down row
#define CFG_ROW_APD 59
// Naive detection of the board's RAM size - for support of big Fuse map:
// PIN_A11 - present on MEGA (8kB) or Leonardo (2.5kB SRAM)
// _RENESAS_RA_ - Uno R4 (32kB)
#if defined(PIN_A11) || defined(_RENESAS_RA_)
#define RAM_BIG
#endif
// common CFG fuse address map for cfg16V8 and cfg20V8
// the only difference is the starting address: 2048 for cfg16V8 and 2560 for cfg20V8
// total size: 82
static const unsigned char cfgV8[] PROGMEM =
{
80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,
0,1,2,3,
145,
72,73,74,75,76,77,78,79,
144,
4,5,6,7,
112,113,114,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132,133,134,135,136,137,138,139,140,141,142,143,
};
// common CFG fuse address map for cfg16V8AB and cfg20V8AB
// the only difference is the starting address: 2048 for cfg16V8AB and 2560 for cfg20V8AB
// total size: 82
static const unsigned char cfgV8AB[] PROGMEM =
{
0,1,2,3,
145,
72,73,74,75,
80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112,113,114,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132,133,134,135,136,137,138,139,140,141,142,143,
76,77,78,79,
144,
4,5,6,7,
};
// common CFG fuse address map for cfg18V10
// starting address: 3456
// total size 20
static const unsigned char cfg18V10[] PROGMEM =
{
1, 0, 3, 2, 5, 4, 7, 6, 9, 8, 11, 10, 13, 12, 15, 14, 17, 16, 19, 18
};
// common CFG fuse address map for cfg20RA10
// starting address: 3200
// total size 10
static const unsigned char cfgRA10[] PROGMEM =
{
0, 1, 2, 3, 4, 5, 6, 7, 8, 9
};
// common CFG fuse address map for cfg20XV10
// starting address: 1600
// total size 31
static const unsigned char cfgXV10[] PROGMEM =
{
30,
28, 29,
20, 21, 22,
10, 11, 12, 13, 14,
0, 1, 2, 3, 4,
27, 26,
23, 24, 25,
19, 18, 17, 16, 15,
9, 8, 7, 6, 5
};
// common CFG fuse address map for cfg22V10
// starting address: 5808
// total size 20
static const unsigned char cfgV10[] PROGMEM =
{
1,0,3,2,5,4,7,6,9,8,11,10,13,12,15,14,17,16,19,18,
};
// common CFG fuse address map for cfg26CV12
// starting address: 6344
// total size 24
static const unsigned char cfg26CV12[] PROGMEM =
{
1, 0, 3, 2, 5, 4, 7, 6, 9, 8, 11, 10, 13, 12, 15, 14, 17, 16, 19, 18, 21, 20, 23, 22
};
// common CFG fuse address map for cfg26V12
// starting address: 7800
// total size 48
static const unsigned char cfg26V12[] PROGMEM =
{
36, 24, 12, 0, 37, 25, 13, 1, 38, 26, 14, 2, 39, 27, 15, 3,
40, 28, 16, 4, 41, 29, 17, 5, 42, 30, 18, 6, 43, 31, 19, 7,
44, 32, 20, 8, 45, 33, 21, 9, 46, 34, 22, 10, 47, 35, 23, 11
};
// common CFG fuse address map for cfg6001
// starting address: 8154
// total size 68
static const unsigned char cfg6001[] PROGMEM =
{
67, 66,
25, 29, 33, 37, 41, 45, 49, 53, 57, 61,
60, 56, 52, 48, 44, 40, 36, 32, 28, 24,
62, 63, 58, 59, 54, 55, 50, 51, 46, 47,
42, 43, 38, 39, 34, 35, 30, 31, 26, 27,
2, 5, 8, 11, 14, 17, 20, 23,
0, 3, 6, 9, 12, 15, 18, 21,
22, 19, 16, 13, 10, 7, 4, 1,
64, 65
};
// common CFG fuse address map for cfg6002
// starting address: 8154
// total size 104
static const unsigned char cfg6002[] PROGMEM =
{
103, 102,
25, 29, 33, 37, 41, 45, 49, 53, 57, 61,
60, 56, 52, 48, 44, 40, 36, 32, 28, 24,
62, 63, 58, 59, 54, 55, 50, 51, 46, 47,
42, 43, 38, 39, 34, 35, 30, 31, 26, 27,
101, 100, 99, 98, 97, 96, 95, 94, 93,
92, 91, 90, 89, 88, 87, 86, 85, 84,
66, 67, 68, 69, 70, 71, 72, 73, 74,
75, 76, 77, 78, 79, 80, 81, 82, 83,
2, 5, 8, 11, 14, 17, 20, 23,
0, 3, 6, 9, 12, 15, 18, 21,
22, 19, 16, 13, 10, 7, 4, 1,
64, 65
};
// TODO: handle those:
/*
30, // 75: Security?
135, // 70: Powerdown
136, // 71: PinKeeper
137, // 72: reserved1
138, // 73: reserved2
139, // 74: reserved3
*/
static const uint8_t cfgV750[] PROGMEM = {
0, 3, 6, 9, 12, 15, 18, 21, 24, 27, // S0
1, 4, 7, 10, 13, 16, 19, 22, 25, 28, // S1
2, 5, 8, 11, 14, 17, 20, 23, 26, 29, // S2
31, 35, 39, 43, 47, 51, 55, 59, 63, 67, // S3
32, 36, 40, 44, 48, 52, 56, 60, 64, 68, // S4
33, 37, 41, 45, 49, 53, 57, 61, 65, 69, // S5
34, 38, 42, 46, 50, 54, 58, 62, 66, 70 // S6
};
// UES user electronic signature
// PES programmer electronic signature (ATF = text string, others = Vendor/Vpp/timing)
// cfg configuration bits for OLMCs
// GAL info
typedef struct
{
GALTYPE type;
unsigned char id0,id1; /* variant 1, variant 2 (eg. 16V8=0x00, 16V8A+=0x1A)*/
short fuses; /* total number of fuses */
char pins; /* number of pins on chip */
char rows; /* number of fuse rows */
unsigned char bits; /* number of fuses per row */
char uesrow; /* UES row number */
short uesfuse; /* first UES fuse number */
char uesbytes; /* number of UES bytes */
char eraserow; /* row adddeess for erase */
char eraseallrow; /* row address for erase all (also PES) */
char pesrow; /* row address for PES read/write */
char pesbytes; /* number of PES bytes */
char cfgrow; /* row address of config bits (ACW) */
unsigned short cfgbase; /* base address of the config bit numbers */
const unsigned char *cfg; /* pointer to config bit numbers */
unsigned char cfgbits; /* number of config bits */
unsigned char cfgmethod; /* strobe or set row for reading config */
PINOUT pinout;
} galinfo_t;
const static galinfo_t galInfoList[] PROGMEM =
{
// +fuses +bits +uesbytes +pesrow +cfgbase
// | +pins | +uesrow | +eraserow| +pesbytes | +cfg
// +-- type + id0 + id1 | | +rows | | +uesfuse | +eraseallrow +cfgrow | | + cfgbits +cfgmethod +pinout
// | | | | | | | | | | | | | | | | | | | |
{UNKNOWN, 0x00, 0x00, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 8, 0, 0, NULL , 0 , 0 , PINOUT_UNKNOWN},
{GAL16V8, 0x00, 0x1A, 2194, 20, 32, 64, 32, 2056, 8, 63, 62, 58, 8, 60, CFG_BASE_16 , cfgV8AB , sizeof(cfgV8AB) , CFG_STROBE_ROW, PINOUT_16V8 },
{GAL18V10, 0x50, 0x51, 3540, 20, 36, 96, 44, 3476, 8, 61, 60, 58, 10, 16, CFG_BASE_18 , cfg18V10 , sizeof(cfg18V10) , CFG_SET_ROW , PINOUT_18V10 },
{GAL20V8, 0x20, 0x3A, 2706, 24, 40, 64, 40, 2568, 8, 63, 62, 58, 8, 60, CFG_BASE_20 , cfgV8AB , sizeof(cfgV8AB) , CFG_STROBE_ROW, PINOUT_20V8 },
{GAL20RA10, 0x60, 0x61, 3274, 24, 40, 80, 40, 3210, 8, 61, 60, 58, 10, 16, CFG_BASE_20RA, cfgRA10 , sizeof(cfgRA10) , CFG_SET_ROW , PINOUT_22V10 },
{GAL20XV10, 0x65, 0x66, 1671, 24, 40, 40, 44, 1631, 5, 61, 60, 58, 5, 16, CFG_BASE_20XV, cfgXV10 , sizeof(cfgXV10) , CFG_SET_ROW , PINOUT_22V10 },
{GAL22V10, 0x48, 0x49, 5892, 24, 44, 132, 44, 5828, 8, 61, 62, 58, 10, 16, CFG_BASE_22 , cfgV10 , sizeof(cfgV10) , CFG_SET_ROW , PINOUT_22V10 },
{GAL26CV12, 0x58, 0x59, 6432, 28, 52, 122, 52, 6368, 8, 61, 60, 58, 12, 16, CFG_BASE_26CV, cfg26CV12, sizeof(cfg26CV12), CFG_SET_ROW , PINOUT_22V10 },
{GAL26V12, 0x5D, 0x5D, 7912, 28, 52, 150, 52, 7848, 8, 61, 60, 58, 12, 16, CFG_BASE_26V , cfg26V12 , sizeof(cfg26V12) , CFG_SET_ROW , PINOUT_22V10 },
{GAL6001, 0x40, 0x41, 8294, 24, 78, 75, 97, 8222, 9, 63, 62, 96, 8, 8, CFG_BASE_600 , cfg6001 , sizeof(cfg6001) , CFG_SET_ROW , PINOUT_600 },
{GAL6002, 0x44, 0x44, 8330, 24, 78, 75, 97, 8258, 9, 63, 62, 96, 8, 8, CFG_BASE_600 , cfg6002 , sizeof(cfg6002) , CFG_SET_ROW , PINOUT_600 },
{ATF16V8B, 0x00, 0x00, 2194, 20, 32, 64, 32, 2056, 8, 63, 62, 58, 8, 60, CFG_BASE_16 , cfgV8AB , sizeof(cfgV8AB) , CFG_STROBE_ROW, PINOUT_16V8 },
{ATF20V8B, 0x00, 0x00, 2706, 24, 40, 64, 40, 2568, 8, 63, 62, 58, 8, 60, CFG_BASE_20 , cfgV8AB , sizeof(cfgV8AB) , CFG_STROBE_ROW, PINOUT_20V8 },
{ATF22V10B, 0x00, 0x00, 5892, 24, 44, 132, 44, 5828, 8, 61, 62, 58, 10, 16, CFG_BASE_22 , cfgV10 , sizeof(cfgV10) , CFG_SET_ROW , PINOUT_22V10 },
{ATF22V10C, 0x00, 0x00, 5892, 24, 44, 132, 44, 5828, 8, 61, 62, 58, 10, 16, CFG_BASE_22 , cfgV10 , sizeof(cfgV10) , CFG_SET_ROW , PINOUT_22V10 },
{ATF750C, 0x00, 0x00, 14499, 24, 84, 171, 84,14435, 8, 61, 60,127, 10, 16, CFG_BASE_750 , cfgV750 , sizeof(cfgV750) , CFG_STROBE_ROW2, PINOUT_22V10 }, // TODO: not all numbers are clear
};
galinfo_t galinfo __attribute__ ((section (".noinit"))); //preserve data between resets
#ifdef RAM_BIG
// for ATF750C
// MAXFUSES = (((171 * 84 bits) + uesbits + (10*3 + 1 + 10*4 + 5)) + 7) / 8
// (14504 + 7) / 8 = 1813
#define MAXFUSES 1813
#else
// Boards with small RAM (< 2.5kB) do not support ATF750C
// MAXFUSES calculated as the biggest required space to hold the fuse bitmap
// MAXFUSES = GAL6002 8330 bits = 8330/8 = 1041.25 bytes rounded up to 1042 bytes
//#define MAXFUSES 1042
//extra space added for sparse fusemap (just enough to fit erased ATF750C)
#define MAXFUSES 1332
#define USE_SPARSE_FUSEMAP
#endif
GALTYPE gal __attribute__ ((section (".noinit"))); //the gal device index pointing to galInfoList, value is preserved between resets
static short erasetime = 100, progtime = 100;
static uint8_t vpp = 0;
char echoEnabled;
unsigned char pes[12];
char line[32];
short lineIndex;
char endOfLine;
char mapUploaded;
char isUploading;
char uploadError;
unsigned char fusemap[MAXFUSES];
unsigned char flagBits;
char varVppExists;
uint8_t lastShiftRegVal = 0;
static void setFuseBit(unsigned short bitPos);
static unsigned short checkSum(unsigned short n);
static char checkGalTypeViaPes(void);
static void turnOff(void);
static void printFormatedNumberHex2(unsigned char num) ;
#include "aftb_vpp.h"
#include "aftb_sparse.h"
// share fusemap buffer with jtag
#define XSVF_HEAP fusemap
#include "jtag_xsvf_player.h"
// print some help on the serial console
void printHelp(char full) {
Serial.println(F("AFTerburner v." VERSION));
// indication for PC software that the new board desgin is used
if (varVppExists) {
Serial.println(F(" varVpp "));
}
#ifdef RAM_BIG
Serial.println(F(" RAM-BIG "));
#endif
if (!full) {
Serial.println(F("type 'h' for help"));
return;
}
Serial.println(F("commands:"));
Serial.println(F(" h - print help"));
Serial.println(F(" e - toggle echo"));
Serial.println(F(" p - read & print PES"));
Serial.println(F(" r - read & print fuses"));
Serial.println(F(" u - upload fuses"));
Serial.println(F(" w - write uploaded fuses"));
Serial.println(F(" v - verify fuses"));
Serial.println(F(" c - erase chip"));
Serial.println(F(" t - test & set VPP"));
Serial.println(F(" b - calibrate VPP"));
Serial.println(F(" m - measure VPP"));
}
static void setFlagBit(uint8_t flag, uint8_t value) {
if (value) {
flagBits |= flag;
} else {
flagBits &= ~flag;
}
}
static void setPinMuxUnused(uint8_t pin, uint8_t pm) {
// set to OUTPUT during active GAL operation and to INPUT when GAL is inactive
pinMode(pin, pm);
digitalWrite(pin, LOW);
}
static void setPinMux(uint8_t pm) {
// ensure pull-up is enabled during reading and disabled when inactive on DOUT pin
uint8_t doutMode = pm == OUTPUT ? INPUT_PULLUP: INPUT;
switch (gal) {
case GAL16V8:
case ATF16V8B:
pinMode(PIN_ZIF10, INPUT); //GND via MOSFET
pinMode(PIN_ZIF11, INPUT);
pinMode(PIN_ZIF13, INPUT);
pinMode(PIN_ZIF14, INPUT);
pinMode(PIN_ZIF16, doutMode); //DOUT
// ensure ZIF10 is Grounded via transistor
digitalWrite(PIN_ZIF_GND_CTRL, pm == OUTPUT ? HIGH: LOW);
break;
case GAL18V10:
pinMode(PIN_ZIF10, INPUT); //GND via MOSFET
pinMode(PIN_ZIF11, INPUT);
pinMode(PIN_ZIF13, INPUT);
pinMode(PIN_ZIF14, INPUT);
pinMode(PIN_ZIF9, doutMode); //DOUT
// ensure ZIF10 is Grounded via transistor
digitalWrite(PIN_ZIF_GND_CTRL, pm == OUTPUT ? HIGH: LOW);
//pull down unused pins when active
setPinMuxUnused(PIN_ZIF15, pm);
setPinMuxUnused(PIN_ZIF16, pm);
break;
case GAL20V8:
case ATF20V8B:
pinMode(PIN_ZIF10, pm);
pinMode(PIN_ZIF11, pm);
pinMode(PIN_ZIF13, pm);
pinMode(PIN_ZIF14, pm);
pinMode(PIN_ZIF15, doutMode); //DOUT
pinMode(PIN_ZIF16, pm);
// ensure ZIF10 GND pull is disabled
digitalWrite(PIN_ZIF_GND_CTRL, LOW);
//pull down unused pins when active
setPinMuxUnused(PIN_ZIF14, pm);
setPinMuxUnused(PIN_ZIF16, pm);
setPinMuxUnused(PIN_ZIF23, pm);
break;
case GAL20RA10:
case GAL20XV10:
case GAL22V10:
case GAL26CV12:
case GAL26V12:
case ATF22V10B:
case ATF22V10C:
case ATF750C:
pinMode(PIN_ZIF10, pm);
pinMode(PIN_ZIF11, pm);
pinMode(PIN_ZIF13, pm);
pinMode(PIN_ZIF14, doutMode); //DOUT
pinMode(PIN_ZIF15, pm);
pinMode(PIN_ZIF16, pm);
// ensure ZIF10 GND pull is disabled
digitalWrite(PIN_ZIF_GND_CTRL, LOW);
//pull down unused pins when active
setPinMuxUnused(PIN_ZIF15, pm);
setPinMuxUnused(PIN_ZIF16, pm);
setPinMuxUnused(PIN_ZIF22, pm);
setPinMuxUnused(PIN_ZIF23, pm);
break;
case GAL6001:
case GAL6002:
pinMode(PIN_ZIF10, pm);
pinMode(PIN_ZIF11, pm);
pinMode(PIN_ZIF13, pm);
pinMode(PIN_ZIF14, doutMode); //DOUT
pinMode(PIN_ZIF15, pm);
pinMode(PIN_ZIF16, pm);
// ensure ZIF10 GND pull is disabled
digitalWrite(PIN_ZIF_GND_CTRL, LOW);
//pull down unused pins when active
setPinMuxUnused(PIN_ZIF3, pm);
setPinMuxUnused(PIN_ZIF15, pm);
setPinMuxUnused(PIN_ZIF16, pm);
setPinMuxUnused(PIN_ZIF22, pm);
break;
}
}
static void setupGpios(uint8_t pm) {
// Serial input of the GAL chip, output from Arduino
pinMode(PIN_SDIN, pm);
pinMode(PIN_STROBE, pm);
pinMode(PIN_PV, pm);
pinMode(PIN_RA0, pm);
pinMode(PIN_RA1, pm);
pinMode(PIN_RA2, pm);
pinMode(PIN_RA3, pm);
pinMode(PIN_RA4, pm);
pinMode(PIN_RA5, pm);
pinMode(PIN_SCLK, pm);
pinMode(PIN_VPP, pm);
if (varVppExists) {
pinMode(PIN_ZIF_GND_CTRL, OUTPUT);
//disconnect shift register pins (High Z) when pm == Input
digitalWrite(PIN_SHR_EN, pm == INPUT ? HIGH : LOW);
setPinMux(pm);
}
}
#define SHR_SET_BIT(X) digitalWrite(PIN_SHR_CLK, 0); \
digitalWrite(PIN_SHR_DAT, (X) ? HIGH : LOW); \
digitalWrite(PIN_SHR_CLK, 1)
static void setShiftReg(uint8_t val) {
lastShiftRegVal = val;
//assume CS is high
//ensure CLK is high (might be set low by other SPI devices)
digitalWrite(PIN_SHR_CLK, 1);
// set CS low
digitalWrite(PIN_SHR_CS, 0);
SHR_SET_BIT(val & 0b10000000);
SHR_SET_BIT(val & 0b1000000);
SHR_SET_BIT(val & 0b100000);
SHR_SET_BIT(val & 0b10000);
SHR_SET_BIT(val & 0b1000);
SHR_SET_BIT(val & 0b100);
SHR_SET_BIT(val & 0b10);
SHR_SET_BIT(val & 0b1);
digitalWrite(PIN_SHR_CS, 1);
}
// setup the Arduino board
void setup() {
// initialize serial:
Serial.begin(57600);
isUploading = 0;
endOfLine = 0;
echoEnabled = 0;
mapUploaded = 0;
lineIndex = 0;
setFlagBit(FLAG_BIT_TYPE_CHECK, 1); //do type check
//check & initialise variable voltage (old / new board design)
varVppExists = varVppInit();
// shift register
pinMode(PIN_SHR_EN, OUTPUT);
// Serial output from the GAL chip, input for Arduino
pinMode(PIN_SDOUT, INPUT);
// Set all GPIO pins to Input to prevent accidents when
// inserting the GAL IC into socket.
setupGpios(INPUT);
printHelp(0);
if (varVppExists) {
// reads the calibration values
if (varVppCheckCalibration()) {
Serial.println(F("I: VPP calib. OK"));
}
// set shift reg Chip select
pinMode(PIN_SHR_CS, OUTPUT);
digitalWrite(PIN_SHR_CS, 1); //unselect the POT's SPI bus
}
Serial.println(">");
}
static void sparseSetup(char clearArray){
// Note: Sparse fuse map is ignored on MCUs with big SRAM
if (gal == ATF750C) {
sparseInit(clearArray);
} else {
sparseDisable();
}
}
//copy galinfo item from the flash array into RAM backed struct
static void copyGalInfo(void) {
memcpy_P(&galinfo, &galInfoList[gal], sizeof(galinfo_t));
sparseSetup(0);
}
// read from serial line and discard the data
void readGarbage() {
while (Serial.available() > 0) {
Serial.read();
}
}
// Reads input from the serial terminal and returns the command
// which is the first character of the entered text.
char handleTerminalCommands() {
char c;
while (Serial.available() > 0) {
c = Serial.read();
line[lineIndex] = c;
if (c == '\n' || c == '\r') {
endOfLine = 1;
}
//echo input to output
else {
if (!isUploading && echoEnabled) {
Serial.print(c);
}
}
if (lineIndex >= sizeof(line)- 2) {
lineIndex = 0;
readGarbage();
Serial.println();
Serial.println(F("Error: line too long."));
} else {
lineIndex++;
}
}
if (endOfLine) {
c = COMMAND_NONE;
//single letter command entered
if (lineIndex == 2) {
c = line[0];
} else if (lineIndex > 2) {
c = line[0];
if (!isUploading || c != '#') {
// prevent 2 character commands from being flagged as invalid
if (!(c == COMMAND_SET_GAL_TYPE || c == COMMAND_CALIBRATION_OFFSET || c == COMMAND_JTAG_PLAYER)) {
c = COMMAND_UNKNOWN;
}
}
}
if (!isUploading) {
Serial.println();
line[lineIndex] = 0;
lineIndex = 0;
}
endOfLine = 0;
return c;
}
return COMMAND_NONE;
}
// Parses decimal integer number typed as 4 or 5 digits.
// Returns the number value.
unsigned short parse45dec(char i, char five) {
unsigned short v = 0;
if (five) { //containts 5 digits
v = (line[i++] - '0') * 10000;
}
v += (line[i++] - '0') * 1000;
v += (line[i++] - '0') * 100;
v += (line[i++] - '0') * 10;
v += line[i] - '0';
return v;
}
// Converts textual hex value 0-9, A-F to a number.
unsigned char toHex(char c) {
if (c >= '0' && c <= '9') return c - '0';
if (c >= 'A' && c <= 'F') return c - 'A' + 10;
if (c >= 'a' && c <= 'f') return c - 'a' + 10;
return 0;
}
// Parses hexdecimal integer number typed as 2 digit.
// Returns the number value.
unsigned short parse2hex(char i) {
if (line[i] == '\r' || line[i] == 0 || line[i] == ' ') {
return -1;
}
unsigned short v = toHex(line[i++]) << 4;
return v + toHex(line[i]);
}
// Parses hexdecimal integer number typed as 4 digit.
// Returns the number value.
unsigned short parse4hex(char i) {
unsigned short v;
if (line[i] == '\r' || line[i] == 0 || line[i] == ' ') {
return -1;
}
v = toHex(line[i++]);
v <<= 4;
v |= toHex(line[i++]);
v <<= 4;
v |= toHex(line[i++]);
v <<= 4;
v |= toHex(line[i]);
return v ;
}
// Parses a line fed by the serial connection.
// This hnadles a primitive upload protocol that
// expects a programatic data feed - not suitable
// for human interaction.
// Data: each command on its own line
// line starts with '#' character followed by a command
// and a space. Then a command specific data follow.
// Commands:
// t <gal index>: gal type index to the GALTYPEE enum
// f <fuse index> <row>: row of fuse-map data starting on fuse bit index
// c <checksum> : checksum of the whole fuse map
// e : end ofthe upload transfer - returns to terminal
void parseUploadLine() {
switch (line[1]) {
case 'e': {
if (uploadError) {
Serial.print(F("ER upload failed"));
} else {
Serial.print(F("OK upload finished"));
}
isUploading = 0;
} break;
// gal type
case 't': {
short v = line[3] - '0';
if (v > 0 && v < LAST_GAL_TYPE) {
gal = (GALTYPE) v;
copyGalInfo();
Serial.print(F("OK gal set: "));
Serial.println((short) gal, DEC);
} else {
Serial.println(F("ER unknown gal index"));
uploadError = 1;
}
} break;
//fusemap data
case 'f': {
char i = 8;
char j;
unsigned short addr;
short v;
char fiveDigitAddr = (line[7] != ' ') ? 1 : 0;
addr = parse45dec(3, fiveDigitAddr);
i += fiveDigitAddr;
do {
v = parse2hex(i);
if (v >= 0) {
for (j = 0; j < 8; j++) {
// if fuse bit is set -> then change the fusemap
if (v & (1 << j)) {
setFuseBit(addr);
}
addr++;
}
i += 2;
}
} while (v >= 0);
//any fuse being set is considered as uploaded fuse map
mapUploaded = 1;
Serial.print(F("OK "));
Serial.println((short) addr, DEC);
} break;
//checksum
case 'c': {
unsigned short val = parse4hex(3);
unsigned char apdFuse = (flagBits & FLAG_BIT_APD) ? 1 : 0;
unsigned short cs = checkSum(galinfo.fuses + apdFuse);
if (cs == val) {
Serial.println(F("OK checksum matches"));
// Conditioning jed files might not have any fuse set, so as long as
// they supply empty checksum (C0000) the upload is OK.
mapUploaded = 1;
} else {
uploadError = 1;
Serial.print(F("ER checksum:"));
Serial.print(cs, HEX);
Serial.print(F(" expected:"));
Serial.println(val, HEX);
}
} break;
// PES
case 'p': {
uint8_t i = 0;
uint8_t j = 3;
while (i < 8) {
pes[i] = parse2hex(j);
i++;
j+=3; //AB:00:... - 3 characters per one PES byte
}
} break;
default:
uploadError = 1;
Serial.println(F("ER unknown upload cmd"));
}
lineIndex = 0;
}
// *********************************************************
// set/reset individual pins of GAL
static void setVCC(char on) {
//no control for turning the voltage on of
//it is assumed the voltage is always on
}
static void setVPP(char on) {
// new board desgin
if (varVppExists) {
uint8_t v = VPP_11V0;
// when PES is read the VPP is not determined via PES
if (on == READPES) {
if (gal == ATF16V8B || gal == ATF20V8B || gal == ATF22V10B || gal == ATF22V10C || gal == ATF750C) {
v = VPP_10V5;
} else {
v = VPP_11V5;
}
#if 0
Serial.print(F("VPP index="));
Serial.println(v);
#endif
} else {
//safety check
if (vpp < 36) {
vpp = 36; //9V
} else
if (vpp > 66) {
vpp = 48; //12V
}
v = (vpp >> 1) - 18; // 18: 2 * 9V, resolution 0.5V (not 0.25V) hence 'vpp >> 1'
#if 0
Serial.print(F("setVPP "));
Serial.print(vpp);
Serial.print(F(" index="));
Serial.println(v);
#endif
}
varVppSet(on ? v : VPP_5V0);
delay(50); //settle the voltage
}
// old board design
else {
//programming voltage is controlled by VPP_PIN,
//but the programming voltage must be set manually by user turning a Pot
digitalWrite(PIN_VPP, on ? 1 : 0);
//Serial.print(F("VPP set to:"));
//Serial.println( on ? "12V": "5V");
delay(10);
}
}
static void setSTB(char on) {
if (varVppExists) {
const PINOUT p = galinfo.pinout;
uint8_t pin = PIN_ZIF13;
if (p == PINOUT_16V8) {
pin = PIN_ZIF15;
} else
if (p == PINOUT_18V10) {
pin = PIN_ZIF8;
}
digitalWrite(pin, on ? 1:0);
} else {
digitalWrite(PIN_STROBE, on ? 1:0);
}
}
static void setPV(char on) {
if (varVppExists) {
const PINOUT p = galinfo.pinout;
uint8_t pin = PIN_ZIF23;
if (p == PINOUT_22V10) {
pin = PIN_ZIF3;
} else
if (p == PINOUT_20V8) {
pin = PIN_ZIF22;
}
digitalWrite(pin, on ? 1:0);
} else {
digitalWrite(PIN_PV, on ? 1:0);
}
}
static void setSDIN(char on) {
if (varVppExists) {
const PINOUT p = galinfo.pinout;
if (p == PINOUT_18V10) {
if (on) {
lastShiftRegVal |= PIN_ZIF7;
} else {
lastShiftRegVal &= ~PIN_ZIF7;
}
setShiftReg(lastShiftRegVal);
} else {
const uint8_t pin = (p == PINOUT_16V8) ? PIN_ZIF9 : PIN_ZIF11;
digitalWrite(pin, on ? 1:0);
}
} else {
digitalWrite(PIN_SDIN, on ? 1:0);
}
}
static void setSCLK(char on){
if (varVppExists) {
const PINOUT p = galinfo.pinout;
if (p == PINOUT_18V10) {
if (on) {
lastShiftRegVal |= PIN_ZIF6;
} else {
lastShiftRegVal &= ~PIN_ZIF6;
}
setShiftReg(lastShiftRegVal);
} else {
uint8_t pin = (p == PINOUT_16V8) ? PIN_ZIF8 : PIN_ZIF10;
digitalWrite(pin, on ? 1:0);
}
} else {
digitalWrite(PIN_SCLK, on ? 1:0);
}
}
// output row address (RA0-5)
static void setRow(char row)
{
if (varVppExists) {
uint8_t srval = 0;
const PINOUT p = galinfo.pinout;
if (p == PINOUT_16V8) {
digitalWrite(PIN_ZIF22, (row & 0x1)); //RA0
digitalWrite(PIN_ZIF3 , (row & 0x2)); //RA1
if (row & 0x4) srval |= PIN_ZIF4; //RA2
if (row & 0x8) srval |= PIN_ZIF5; //RA3
if (row & 0x10) srval |= PIN_ZIF6; //RA4
if (row & 0x20) srval |= PIN_ZIF7; //RA5
} else
if (p == PINOUT_18V10) {
digitalWrite(PIN_ZIF22, (row & 0x1)); //RA0
if (row & 0x2) srval |= PIN_ZIF21; //RA1
if (row & 0x4) srval |= PIN_ZIF20; //RA2
digitalWrite(PIN_ZIF3 , (row & 0x8)); //RA3
if (row & 0x10) srval |= PIN_ZIF4; //RA4
if (row & 0x20) srval |= PIN_ZIF5; //RA5
} else
if (p == PINOUT_22V10 || p == PINOUT_600) {
if (row & 0x1) srval |= PIN_ZIF4; //RA0
if (row & 0x2) srval |= PIN_ZIF5; //RA1
if (row & 0x4) srval |= PIN_ZIF6; //RA2
if (row & 0x8) srval |= PIN_ZIF7; //RA3
digitalWrite(PIN_ZIF8, (row & 0x10)); //RA4
digitalWrite(PIN_ZIF9, (row & 0x20)); //RA5
} else { //PINOUT_20V8
if (row & 0x1) srval |= PIN_ZIF21; //RA0
digitalWrite(PIN_ZIF3 , (row & 0x2)); //RA1
if (row & 0x4) srval |= PIN_ZIF4; //RA2
if (row & 0x8) srval |= PIN_ZIF5; //RA3
digitalWrite(PIN_ZIF8, (row & 0x10)); //RA4
digitalWrite(PIN_ZIF9, (row & 0x20)); //RA5
}
setShiftReg(srval);
} else {
digitalWrite(PIN_RA0, (row & 0x1));
digitalWrite(PIN_RA1, ((row & 0x2) ? 1:0));
digitalWrite(PIN_RA2, ((row & 0x4) ? 1:0));
digitalWrite(PIN_RA3, ((row & 0x8) ? 1:0));
digitalWrite(PIN_RA4, ((row & 0x10) ? 1:0));
digitalWrite(PIN_RA5, ((row & 0x20) ? 1:0));
}
}
// serial data out form the GAL chip -> received by Arduino
static char getSDOUT(void)
{
if (varVppExists) {
const PINOUT p = galinfo.pinout;
uint8_t pin = PIN_ZIF16;
if (p == PINOUT_22V10 || p == PINOUT_600) {
pin = PIN_ZIF14;
} else
if (p == PINOUT_20V8) {
pin = PIN_ZIF15;
} else
if (p == PINOUT_18V10) {
pin = PIN_ZIF9;
}
return digitalRead(pin) != 0;
} else {
return digitalRead(PIN_SDOUT) != 0;
}
}
// GAL finish sequence
static void turnOff(void)
{
delay(100);
setPV(0); // P/V- low
setRow(0x3F);// RA0-5 high
setSDIN(1); // SDIN high
setVPP(0); // Vpp off (+12V)
setPV(1); // P/V- high
delay(2);
setVCC(0); // turn off VCC (if controlled)
setupGpios(INPUT);
delay(100); //ensure VPP is low
}
// GAL init sequence
static void turnOn(char mode) {
setupGpios(OUTPUT);
if (mode == READPES) {
mode = 2;
} else
if (
mode == WRITEGAL ||
mode == ERASEGAL ||
mode == ERASEALL ||
mode == BURNSECURITY ||
mode == WRITEPES ||
mode == VPPTEST ||
mode == READGAL
) {
mode = 1;
} else {
mode = 0;
}
// setVPP(mode);
setVPP(0); // VPP off
setPV(0); // P/V- low
setRow(0x3F); // RA0-5 high - erase sequence ?
//setRow(0); // RA0-5 low
setSDIN(1); // SDIN high
setSCLK(1); // SCLK high
setSTB(1); // STB high
setVCC(1); // turn on VCC (if controlled)
delay(100);
setSCLK(0); // SCLK low
setVPP(mode);
delay(20);
}
// clock and receive a bit in from GAL SDOUT
static char receiveBit(void)
{
char b = getSDOUT();
setSCLK(1);
setSCLK(0);
return b;
}
// read n number of bits
static void discardBits(short n)
{
while (n-- > 0) {
receiveBit();
}
}
// clock a bit and send it out to GAL SDIN
static void sendBit(char bitValue, char skipClkLow = 0)
{
setSDIN(bitValue);
setSCLK(1);
// For some reason ATF20V8B needs a slower clock
if (gal == ATF20V8B) {
delay(1);
}
if (!skipClkLow) {
setSCLK(0);
}
}
// send n number of bits to GAL
static void sendBits(short n, char bitValue)
{
char skipClkLow = flagBits & FLAG_BIT_ATF16V8C;
while (n-- > 0) {
sendBit(bitValue, skipClkLow && n == 0);
}
}
// send row address bits to SDIN
// ATF22V10C MSb first, other 22V10 LSb first
static void sendAddress(unsigned char n, unsigned char row)
{
switch (gal) {
case ATF22V10C:
while (n-- > 1) {
sendBit(row & 32); // clock in row number bits 5-1
row <<= 1;
}
setSDIN(row & 32); // SDIN = row number bit 0
break;
case ATF750C:
while (n-- > 1) {
sendBit(row & 1); // clock in row number bits 0-5
row >>= 1;
}
setSDIN(row & 1); // SDIN = row number bit 6
break;
default:
while (n-- > 0) {
sendBit(row & 1); // clock in row number bits 0-5
row >>= 1;
}
setSDIN(0); // SDIN = low
}
}
// pulse STB pin low for some milliseconds
static void strobe(unsigned short msec)
{
setSTB(0);
delay(msec);
setSTB(1);
}
// 16V8, 20V8 RA0-5 = row address, strobe.
// 22V10 RA0-5 = 0, send row address (6 bits), strobe.
// setBit: 0 - do not set bit, 1- set bit value 0, 2 - set bit value 1
static void strobeRow(char row, char setBit = BIT_NONE)
{
unsigned char nBits = 6;
switch(gal) {
case GAL16V8:
case GAL20V8:
case ATF20V8B:
case ATF16V8B:
setRow(row); // set RA0-5 to row number
if (setBit) {
sendBits(1, setBit - 1);
}
strobe(2); // pulse /STB for 2ms
break;
case ATF750C:
nBits = 7;
//fall through
case GAL18V10:
case GAL20RA10:
case GAL20XV10:
case GAL22V10:
case GAL26CV12:
case GAL26V12:
case ATF22V10B:
case ATF22V10C:
setRow(0); // set RA0-5 low
sendAddress(nBits, row); // send row number (6 or 7 bits)
setSTB(0);
setSTB(1); // pulse /STB
setSDIN(0); // SDIN low
break;
case GAL6001:
case GAL6002:
setRow(0);
sendBits(95, 0);
sendBit(1);
sendAddress(7, row);
sendBits(16, 0);
strobe(2); // pulse /STB for 2ms
break;
}
}
static void strobeConfigRow(char row)
{
switch(gal) {
case ATF750C:
setRow(0); // set RA0-5 low
setRow(galinfo.cfgrow);
sendAddress(7, row); // send row number (6 bits)
setSDIN(1); // SDIN high
setSTB(0);
setSTB(1); // pulse /STB
break;
}
}
// read PES: programmer electronic signature (ATF = text string, others = Vendor/Vpp/timing)
static void readPes(void) {
unsigned short bitmask;
short byteIndex;
#ifdef DEBUG_PES
Serial.print(F("testing gal "));
Serial.print(gal, DEC);
Serial.println();
#endif
turnOn(READPES);
strobeRow(galinfo.pesrow);
if (gal == ATF16V8B) {
setPV(1); //Required for ATF16V8C
}
if (gal == GAL6001 || gal == GAL6002) {
discardBits(20);
}
for(byteIndex = 0; byteIndex < galinfo.pesbytes; byteIndex++) {
unsigned char value = 0;
for (bitmask = 0x1; bitmask <= 0x80; bitmask <<= 1) {
if (receiveBit()) {
value |= bitmask;
}
}
pes[byteIndex] = value;
}
turnOff();
}
static void writePes(void) {
uint8_t rbit;
uint8_t b, p;
if (gal == ATF16V8B || gal == ATF20V8B || gal == ATF22V10B || gal == ATF22V10C) {
Serial.println(F("ER write PES not supported"));
return;
}
turnOn(WRITEPES);
setPV(1);
switch(gal) {
case GAL6001:
case GAL6002:
setRow(0);
sendBits(20, 0);
for (rbit = 0; rbit < 64; rbit++) {
b = pes[rbit >> 3];
p = b & (1 << (rbit & 0b111));
sendBit(p);
}
sendBits(11, 0);
sendBit(1);
sendAddress(7, galinfo.pesrow);
sendBits(16, 0);
setSDIN(0);
break;
default:
setRow(galinfo.pesrow);
for (rbit = 0; rbit < 64; rbit++) {
b = pes[rbit >> 3];
p = b & (1 << (rbit & 0b111));
sendBit(p);
}
break;
}
strobe(progtime);
turnOff();
}
static const unsigned char PROGMEM duration[] = {
1, 2, 5, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 200
};
static unsigned char getDuration(unsigned char index) {
if (index > 13) {
return 0;
}
return pgm_read_byte(&duration[index]);
}
static void setGalDefaults(void) {
if (gal == ATF16V8B || gal == ATF20V8B || gal == ATF22V10B || gal == ATF22V10C || gal == ATF750C) {
progtime = 20;
erasetime = 100;
vpp = 42; /* 10.5V */
} else {
progtime = 80;
erasetime = 80;
vpp = 48; /* 12V */
}
}
void parsePes(char type) {
unsigned char algo;
if (UNKNOWN == type) {
type = gal;
}
#ifdef DEBUG_PES
Serial.print(F("Parse pes. gal="));
Serial.println(type, DEC);
#endif
switch (type) {
case ATF16V8B:
case ATF20V8B:
case ATF22V10B:
case ATF22V10C:
case ATF750C:
progtime = 20;
erasetime = 100;
vpp = 48; /* 12.0V */
break;
default:
algo = pes[1] & 0x0F;
if (algo == 5) {
erasetime = (25 << ((pes[4] >> 2) &7)) / 2;
progtime = getDuration(((((unsigned short)pes[5] << 8)| pes[4]) >> 5) & 15);
vpp = 2 * ((pes[5] >> 1) & 31) + 20;
}
else switch(type) {
case GAL16V8:
case GAL20V8:
erasetime=100;
goto more;
case GAL6001:
case GAL6002:
erasetime=50;
more:
switch(algo) {
case 0:
vpp = 63; // 15.75V
progtime = 100;
break;
case 1:
vpp = 63; // 15.75V
progtime = 80;
break;
case 2:
vpp = 66; // 16.5V
progtime = 10;
break;
case 3:
vpp = (pes[3] == NATIONAL) ? 60 : 58; // 15.0V or 14.5V
progtime = 40;
break;
case 4:
vpp = 56; // 14V
progtime = 100;
break;
}
break;
default:
erasetime = (pes[3] == NATIONAL) ? 50 : 100;
switch(algo) {
case 0:
vpp = 66; // 16.5V
progtime = 10;
break;
case 1:
vpp = 63; // 15.75V
progtime = 100;
break;
case 2:
vpp = (pes[3] == NATIONAL) ? 60 : 58; // 15.0V or 14.5V
progtime = 40;
break;
case 3:
vpp = 56; // 14V
progtime = 100;
break;
}
}
}
//Afterburnes seems to work with programming voltages reduced by 1V
vpp -= 4; // -1V
}
// print PES information
void printPes(char type) {
Serial.print(F("PES info: "));
//voltage
if (pes[3] == ATMEL16 || pes[3] == ATMEL22 || pes[3] == ATMEL750) {
//Serial.print(" ");
} else {
if (pes[1] & 0x10) {
Serial.print(F("3.3V "));
} else {
Serial.print(F("5V "));
}
}
//manufacturer
switch (pes[3]) {
case LATTICE: Serial.print(F("Lattice ")); break;
case NATIONAL: Serial.print(F("National ")); break;
case SGSTHOMSON: Serial.print(F("ST Microsystems ")); break;
case ATMEL750:
case ATMEL16:
case ATMEL22: Serial.print(F("Atmel ")); break;
default: Serial.print(F("Unknown GAL, "));
}
// GAL type
switch (type) {
case GAL16V8: Serial.print(F("GAL16V8 ")); break;
case GAL18V10: Serial.print(F("GAL18V10 ")); break;
case GAL20V8: Serial.print(F("GAL20V8 ")); break;
case GAL20RA10: Serial.print(F("GAL20RA10 ")); break;
case GAL20XV10: Serial.print(F("GAL20XV10 ")); break;
case GAL22V10: Serial.print(F("GAL22V10 ")); break;
case GAL26CV12: Serial.print(F("GAL26CV12 ")); break;
case GAL26V12: Serial.print(F("GAL26V12 ")); break;
case GAL6001: Serial.print(F("GAL6001 ")); break;
case GAL6002: Serial.print(F("GAL6002 ")); break;
case ATF16V8B: Serial.print(0 == (flagBits & FLAG_BIT_ATF16V8C) ? F("ATF16V8B "): F("ATF16V8C ")); break;
case ATF20V8B: Serial.print(F("ATF20V8B ")); break;
case ATF22V10B: Serial.print(F("ATF22V10B ")); break;
case ATF22V10C: Serial.print(F("ATF22V10C ")); break;
case ATF750C: Serial.print(F("ATF750C ")); break;
}
//programming info
if (UNKNOWN != type) {
Serial.print(F(" VPP="));
Serial.print(vpp >> 2, DEC);
Serial.print(F("."));
Serial.print((vpp & 3) * 25, DEC);
Serial.print(F(" Timing: prog="));
Serial.print(progtime, DEC);
Serial.print(F(" erase="));
Serial.print(erasetime / 4, DEC);
} else {
Serial.print(F(" try VPP=10..14 in 1V steps"));
}
Serial.println();
}
// sets a fuse bit on particular position
// expects that the fusemap was cleared (set to zero) beforehand
static void setFuseBit(unsigned short bitPos) {
uint16_t pos;
if (sparseFusemapStat) {
pos = sparseSetFuseBit(bitPos);
} else {
pos = bitPos >> 3; //divide the bit position by 8 to get the byte position
}
fusemap[pos] |= (1 << (bitPos & 7));
}
// gets a fuse bit from specific fuse position
static char getFuseBit(unsigned short bitPos) {
uint16_t pos;
if (sparseFusemapStat) {
pos = sparseGetFuseBit(bitPos);
if (pos >= 0xFF00) {
return pos & 0x1;
}
} else {
pos = bitPos >> 3;
}
return (fusemap[pos] & (1 << (bitPos & 7))) ? 1 : 0;
}
static void setFuseBitVal(unsigned short bitPos, char val) {
if (val) {
setFuseBit(bitPos);
}
}
// generic fuse-map reading, fuse-map bits are stored in fusemap array
static void readGalFuseMap(const unsigned char* cfgArray, char useDelay, char doDiscardBits) {
unsigned short cfgAddr = galinfo.cfgbase;
unsigned short row, bit;
unsigned short addr;
if (flagBits & FLAG_BIT_ATF16V8C) {
setPV(0);
}
for(row = 0; row < galinfo.rows; row++) {
strobeRow(row); //set address of the row
if (flagBits & FLAG_BIT_ATF16V8C) {
setSDIN(0);
setPV(1);
}
for(bit = 0; bit < galinfo.bits; bit++) {
// check the received bit is 1 and if so then set the fuse map
if (receiveBit()) {
addr = galinfo.rows;
addr *= bit;
addr += row;
setFuseBit(addr);
}
}
if (useDelay) {
delay(useDelay);
}
if (flagBits & FLAG_BIT_ATF16V8C) {
setPV(0);
}
}
// read UES
strobeRow(galinfo.uesrow);
if (flagBits & FLAG_BIT_ATF16V8C) {
setSDIN(0);
setPV(1);
}
if (doDiscardBits) {
discardBits(doDiscardBits);
}
for(bit = 0; bit < galinfo.uesbytes * 8; bit++) {
if (receiveBit()) {
addr = galinfo.uesfuse;
addr += bit;
setFuseBit(addr);
}
}
if (useDelay) {
delay(useDelay);
}
if (flagBits & FLAG_BIT_ATF16V8C) {
setPV(0);
}
// read CFG
if (galinfo.cfgmethod == CFG_STROBE_ROW2) { //ATF750C
const uint8_t cfgstroberow = 96;
const uint8_t cfgrowlen = 10;
const uint8_t cfgrowcount = (galinfo.cfgbits + (cfgrowlen - 1)) /cfgrowlen;
uint8_t i;
for(i = 0; i < cfgrowcount; i++) {
strobeConfigRow(cfgstroberow + i);
for(bit = 0; bit < cfgrowlen; bit++) {
uint8_t absBit = (cfgrowlen * i) + bit;
if (absBit >= galinfo.cfgbits)
break;
if (receiveBit()) {
unsigned char cfgOffset = pgm_read_byte(&cfgArray[absBit]);
setFuseBit(cfgAddr + cfgOffset);
}
}
if (useDelay) {
delay(useDelay);
}
}
} else {
if (galinfo.cfgmethod == CFG_STROBE_ROW) {
strobeRow(galinfo.cfgrow);
if (flagBits & FLAG_BIT_ATF16V8C) {
setSDIN(0);
setPV(1);
}
}
else {
setRow(galinfo.cfgrow);
strobe(1);
}
for(bit = 0; bit < galinfo.cfgbits; bit++) {
if (receiveBit()) {
unsigned char cfgOffset = pgm_read_byte(&cfgArray[bit]); //read array byte flom flash
setFuseBit(cfgAddr + cfgOffset);
}
}
}
//check APD fuse bit - only for ATF16V8C or ATF22V10C
if ((flagBits & FLAG_BIT_ATF16V8C) || gal == ATF22V10C) {
setPV(0);
if (gal == ATF22V10C) {
setRow(0);
sendAddress(6, CFG_ROW_APD);
strobe(1);
} else { //ATF16V8C
setRow(CFG_ROW_APD);
strobe(1);
setPV(1);
}
setFlagBit(FLAG_BIT_APD, receiveBit());
}
#if 0
if (sparseFusemapStat) {
sparsePrintStat();
}
#endif
}
static void readGalFuseMap600(const unsigned char* cfgArray) {
unsigned short row, bit;
unsigned short addr;
for (row = 0; row < 78; row++)
{
strobeRow(row);
discardBits(20);
for (bit = 0; bit < 11; bit++)
setFuseBitVal(7296 + 78 * bit + row, receiveBit());
for (bit = 0; bit < 64; bit++)
setFuseBitVal(114 * bit + row, receiveBit());
discardBits(24);
}
for (row = 0; row < 64; row++)
{
sendBits(31, 0);
for (bit = 0; bit < 64; bit++)
sendBit(bit != row);
sendBits(24, 0);
setSDIN(0);
strobe(2);
for (bit = 0; bit < 20; bit++)
setFuseBitVal(78 + 114 * row + bit, receiveBit());
discardBits(83);
for (bit = 0; bit < 16; bit++)
setFuseBitVal(98 + 114 * row + bit, receiveBit());
}
// UES
strobeRow(galinfo.uesrow);
discardBits(20);
addr = galinfo.uesfuse;
for (bit = 0; bit < 72; bit++)
setFuseBitVal(addr + bit, receiveBit());
// CFG
setRow(galinfo.cfgrow);
strobe(2);
addr = galinfo.cfgbase;
for (bit = 0; bit < galinfo.cfgbits; bit++) {
unsigned char cfgOffset = pgm_read_byte(&cfgArray[bit]); //read array byte flom flash
setFuseBitVal(addr + cfgOffset, receiveBit());
}
}
// generic fuse-map verification, fuse map bits are compared against read bits
static unsigned short verifyGalFuseMap(const unsigned char* cfgArray, char useDelay, char doDiscardBits) {
unsigned short cfgAddr = galinfo.cfgbase;
unsigned short row, bit;
unsigned short addr;
char fuseBit; // fuse bit received from GAL
char mapBit; // fuse bit stored in RAM
unsigned short errors = 0;
#ifdef DEBUG_VERIFY
Serial.print(F("rot f:"));
Serial.println(rotatedFuseMap, DEC);
#endif
if (flagBits & FLAG_BIT_ATF16V8C) {
setPV(0);
}
// read fuse rows
for(row = 0; row < galinfo.rows; row++) {
strobeRow(row);
if (flagBits & FLAG_BIT_ATF16V8C) {
setSDIN(0);
setPV(1);
}
for(bit = 0; bit < galinfo.bits; bit++) {
addr = galinfo.rows;
addr *= bit;
addr += row;
mapBit = getFuseBit(addr); //bit from RAM
fuseBit = receiveBit(); // read from GAL
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.print(F("f a="));
Serial.print(addr, DEC);
#endif
errors++;
}
}
if (useDelay) {
delay(useDelay);
}
if (flagBits & FLAG_BIT_ATF16V8C) {
setPV(0);
}
}
// read UES
strobeRow(galinfo.uesrow);
if (flagBits & FLAG_BIT_ATF16V8C) {
setSDIN(0);
setPV(1);
}
if (doDiscardBits) {
discardBits(doDiscardBits);
}
for(bit = 0; bit < galinfo.uesbytes * 8; bit++) {
addr = galinfo.uesfuse;
addr += bit;
mapBit = getFuseBit(addr);
fuseBit = receiveBit();
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.print(F("U a="));
Serial.println(bit, DEC);
#endif
errors++;
}
}
if (useDelay) {
delay(useDelay);
}
if (flagBits & FLAG_BIT_ATF16V8C) {
setPV(0);
}
if (galinfo.cfgmethod == CFG_STROBE_ROW2) { //ATF750C
const uint8_t cfgstroberow = 96;
const uint8_t cfgrowlen = 10;
const uint8_t cfgrowcount = (galinfo.cfgbits + (cfgrowlen - 1)) /cfgrowlen;
uint8_t i;
for(i = 0; i < cfgrowcount; i++) {
strobeConfigRow(cfgstroberow + i);
for(bit = 0; bit < cfgrowlen; bit++) {
uint8_t absBit = (cfgrowlen * i) + bit;
if (absBit >= galinfo.cfgbits) {
break;
}
mapBit = getFuseBit(cfgAddr + pgm_read_byte(&cfgArray[absBit])); // cfgAddr + cfgOffset
fuseBit = receiveBit();
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.print(F("C a="));
Serial.println(absBit, DEC);
#endif
errors++;
}
}
if (useDelay) {
delay(useDelay);
}
}
} else {
if (galinfo.cfgmethod == CFG_STROBE_ROW) {
strobeRow(galinfo.cfgrow);
if (flagBits & FLAG_BIT_ATF16V8C) {
setSDIN(0);
setPV(1);
}
} else {
setRow(galinfo.cfgrow);
strobe(1);
}
for(bit = 0; bit < galinfo.cfgbits; bit++) {
unsigned char cfgOffset = pgm_read_byte(&cfgArray[bit]); //read array byte flom flash
mapBit = getFuseBit(cfgAddr + cfgOffset);
fuseBit = receiveBit();
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.print(F("C a="));
Serial.println(bit, DEC);
#endif
errors++;
}
}
}
//verify PD fuse on Atmel's C GALs
if ((flagBits & FLAG_BIT_ATF16V8C) || gal == ATF22V10C) {
setPV(0);
if (gal == ATF22V10C) {
setRow(0);
sendAddress(6, CFG_ROW_APD);
strobe(1);
} else { //ATF16V8C
setRow(CFG_ROW_APD);
strobe(1);
setPV(1);
}
mapBit = (flagBits & FLAG_BIT_APD)? 1 : 0;
fuseBit = receiveBit();
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.println(F("C pd"));
#endif
errors++;
}
}
return errors;
}
static unsigned short verifyGalFuseMap600(const unsigned char* cfgArray) {
unsigned short row, bit;
unsigned short addr;
char fuseBit; // fuse bit received from GAL
char mapBit; // fuse bit stored in RAM
unsigned short errors = 0;
for (row = 0; row < 78; row++)
{
strobeRow(row);
discardBits(20);
for (bit = 0; bit < 11; bit++) {
mapBit = getFuseBit(7296 + 78 * bit + row);
fuseBit = receiveBit();
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.print(F("f a="));
Serial.println(7296 + 78 * bit + row, DEC);
#endif
errors++;
}
}
for (bit = 0; bit < 64; bit++) {
mapBit = getFuseBit(114 * bit + row);
fuseBit = receiveBit();
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.print(F("f a="));
Serial.println(114 * bit + row, DEC);
#endif
errors++;
}
}
discardBits(24);
}
for (row = 0; row < 64; row++)
{
sendBits(31, 0);
for (bit = 0; bit < 64; bit++)
sendBit(bit != row);
sendBits(24, 0);
setSDIN(0);
strobe(2);
for (bit = 0; bit < 20; bit++) {
mapBit = getFuseBit(78 + 114 * row + bit);
fuseBit = receiveBit();
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.print(F("f a="));
Serial.println(78 + 114 * row + bit, DEC);
#endif
errors++;
}
}
discardBits(83);
for (bit = 0; bit < 16; bit++) {
mapBit = getFuseBit(98 + 114 * row + bit);
fuseBit = receiveBit();
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.print(F("f a="));
Serial.println(98 + 114 * row + bit, DEC);
#endif
errors++;
}
}
}
// UES
strobeRow(galinfo.uesrow);
discardBits(20);
addr = galinfo.uesfuse;
for (bit = 0; bit < 72; bit++) {
mapBit = getFuseBit(addr + bit);
fuseBit = receiveBit();
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.print(F("f a="));
Serial.println(addr + bit, DEC);
#endif
errors++;
}
}
// CFG
setRow(galinfo.cfgrow);
strobe(2);
addr = galinfo.cfgbase;
for (bit = 0; bit < galinfo.cfgbits; bit++) {
unsigned char cfgOffset = pgm_read_byte(&cfgArray[bit]); //read array byte flom flash
mapBit = getFuseBit(addr + cfgOffset);
fuseBit = receiveBit();
if (mapBit != fuseBit) {
#ifdef DEBUG_VERIFY
Serial.print(F("f a="));
Serial.println(addr + cfgOffset, DEC);
#endif
errors++;
}
}
return errors;
}
// main fuse-map reading and verification function
// READING: reads fuse rows, UES, CFG from GAL and stores into fusemap bit array RAM.
// VERIFY: reads fuse rows, UES, CFG from GAL and compares with fusemap bit array in RAM.
static void readOrVerifyGal(char verify)
{
unsigned short i;
unsigned char* cfgArray = (unsigned char*) cfgV8;
//ensure fusemap is cleared before READ operation, keep it for VERIFY operation.
if (!verify) {
for (i = 0; i < MAXFUSES; i++) {
fusemap[i] = 0;
}
sparseSetup(1);
}
turnOn(READGAL);
switch(gal)
{
case GAL16V8:
case GAL20V8:
if (pes[2] == 0x1A || pes[2] == 0x3A) {
cfgArray = (unsigned char*) cfgV8AB;
}
//read without delay, no discard
if (verify) {
i = verifyGalFuseMap(cfgArray, 0, 0);
} else {
readGalFuseMap(cfgArray, 0, 0);
}
break;
case ATF16V8B:
case ATF20V8B:
case GAL18V10:
case GAL20RA10:
case GAL20XV10:
case GAL26V12:
case GAL26CV12:
cfgArray = (unsigned char*) galinfo.cfg;
//read without delay, no discard
if (verify) {
i = verifyGalFuseMap(cfgArray, 0, 0);
} else {
readGalFuseMap(cfgArray, 0, 0);
}
break;
case GAL6001:
case GAL6002:
cfgArray = (gal == GAL6001) ? (unsigned char*) cfg6001 : (unsigned char*) cfg6002;
//read without delay, no discard
if (verify) {
i = verifyGalFuseMap600(cfgArray);
} else {
readGalFuseMap600(cfgArray);
}
break;
case GAL22V10:
case ATF22V10B:
case ATF22V10C:
//read with delay 1 ms, discard 68 cfg bits on ATFxx
if (verify) {
i = verifyGalFuseMap(cfgV10, 1, (gal == GAL22V10) ? 0 : 68);
} else {
readGalFuseMap(cfgV10, 1, (gal == GAL22V10) ? 0 : 68);
}
break;
case ATF750C:
//read with delay 1 ms, discard 107 bits on ATF750C
if (verify) {
i = verifyGalFuseMap(galinfo.cfg, 1, galinfo.bits - 8 * galinfo.uesbytes - 1);
} else {
readGalFuseMap(galinfo.cfg, 1, galinfo.bits - 8 * galinfo.uesbytes - 1);
}
}
turnOff();
if (verify && i > 0) {
Serial.print(F("ER verify failed. Bit errors: "));
Serial.println(i, DEC);
}
}
// fuse-map writing function for V8 GAL chips
static void writeGalFuseMapV8(const unsigned char* cfgArray) {
unsigned short cfgAddr = galinfo.cfgbase;
unsigned char row, rbit;
unsigned short addr;
unsigned char rbitMax = galinfo.bits;
const unsigned char skipLastClk = (flagBits & FLAG_BIT_ATF16V8C) ? 1 : 0;
setPV(1);
// write fuse rows
for (row = 0; row < galinfo.rows; row++) {
setRow(row);
for(rbit = 0; rbit < rbitMax; rbit++) {
addr = galinfo.rows;
addr *= rbit;
addr += row;
sendBit(getFuseBit(addr), rbit == rbitMax - 1 ? skipLastClk : 0);
}
strobe(progtime);
}
// write UES
setRow(galinfo.uesrow);
for (rbit = 0; rbit < 64; rbit++) {
addr = galinfo.uesfuse;
addr += rbit;
sendBit(getFuseBit(addr), rbit == 63 ? skipLastClk : 0);
}
strobe(progtime);
// write CFG (all ICs use setRow)
rbitMax = galinfo.cfgbits;
setRow(galinfo.cfgrow);
for(rbit = 0; rbit < rbitMax; rbit++) {
unsigned char cfgOffset = pgm_read_byte(&cfgArray[rbit]); //read array byte flom flash
sendBit(getFuseBit(cfgAddr + cfgOffset), rbit == rbitMax - 1 ? skipLastClk : 0);
}
strobe(progtime);
setPV(0);
// disable power-down if the APD flag is not set (only for ATF16V8C)
if (skipLastClk && (flagBits & FLAG_BIT_APD) == 0) {
setPV(1);
strobeRow(CFG_ROW_APD, BIT_ZERO); // strobe row and send one bit with value 0
setPV(0);
}
}
// fuse-map writing function for V10 GAL chips
static void writeGalFuseMapV10(const unsigned char* cfgArray, char fillUesStart, char useSdin) {
unsigned short cfgAddr = galinfo.cfgbase;
unsigned char row, bit;
unsigned short addr;
unsigned short uesFill = galinfo.bits - galinfo.uesbytes * 8;
setRow(0); //RA0-5 low
// write fuse rows
for (row = 0; row < galinfo.rows; row++) {
for (bit = 0; bit < galinfo.bits; bit++) {
addr = galinfo.rows;
addr *= bit;
addr += row;
sendBit(getFuseBit(addr));
}
sendAddress(6, row);
setPV(1);
strobe(progtime);
setPV(0);
}
// write UES
if (fillUesStart) {
sendBits(uesFill, 1);
}
for (bit = 0; bit < galinfo.uesbytes * 8; bit++) {
addr = galinfo.uesfuse;
addr += bit;
sendBit(getFuseBit(addr));
}
if (!fillUesStart) {
sendBits(uesFill, 1);
}
sendAddress(6, galinfo.uesrow);
setPV(1);
strobe(progtime);
setPV(0);
// write CFG
setRow(galinfo.cfgrow);
for(bit = 0; bit < galinfo.cfgbits - useSdin; bit++) {
unsigned char cfgOffset = pgm_read_byte(&cfgArray[bit]); //read array byte flom flash
sendBit(getFuseBit(cfgAddr + cfgOffset));
}
if (useSdin) {
unsigned char cfgOffset = pgm_read_byte(&cfgArray[19]); //read array byte flom flash
setSDIN(getFuseBit(cfgAddr + cfgOffset));
}
setPV(1);
strobe(progtime);
setPV(0);
if (useSdin && (flagBits & FLAG_BIT_APD) == 0) {
// disable power-down feature (JEDEC bit #5892)
setRow(0);
sendAddress(6, CFG_ROW_APD);
setPV(1);
strobe(progtime);
setPV(0);
}
}
// fuse-map writing function for ATF750C chips
static void writeGalFuseMapV750(const unsigned char* cfgArray) {
unsigned short cfgAddr = galinfo.cfgbase;
unsigned char row, bit;
unsigned short addr;
unsigned short uesFill = galinfo.bits - (galinfo.uesbytes * 8) - 1;
uint8_t cfgRowLen = 10; //ATF750C
uint8_t cfgStrobeRow = 96; //ATF750C
// write fuse rows
setRow(0); //RA0-5 low
delayMicroseconds(20);
for(row = 0; row < galinfo.rows; row++) {
for (bit = 0; bit < galinfo.bits; bit++) {
addr = galinfo.rows;
addr *= bit;
addr += row;
sendBit(getFuseBit(addr));
}
sendAddress(7, row);
setPV(1);
delayMicroseconds(20);
strobe(progtime);
delayMicroseconds(100);
setPV(0);
delayMicroseconds(12);
}
setRow(0); //RA0-5 low
sendBits(uesFill, 0); //send X number of 0 bits between fuse rows and UES data
//write UES
for (bit = 0; bit < (8 * galinfo.uesbytes); bit++) {
addr = galinfo.uesfuse;
addr += bit;
sendBit(getFuseBit(addr));
}
//set 1 bit after UES to 0
sendBits(1, 0);
row = galinfo.uesrow;
sendAddress(7, row);
setPV(1);
strobe(progtime);
setPV(0);
delay(progtime);
// write CFG
uint8_t cfgrowcount = (galinfo.cfgbits + (cfgRowLen - 1)) / cfgRowLen;
for(uint8_t i = 0; i < cfgrowcount; i++) {
setRow(0);
delayMicroseconds(10);
setRow(galinfo.cfgrow);
for(bit = 0; bit < cfgRowLen; bit++) {
uint8_t absBit = bit + (i * cfgRowLen);
//addr = galinfo.cfgbase - (galinfo[gal].bits * rangeStartRow) + cfgArray[absBit];
addr = galinfo.cfgbase + pgm_read_byte(&cfgArray[absBit]);
uint8_t v = getFuseBit(addr);
sendBit(v);
}
sendAddress(7, i + cfgStrobeRow);
delayMicroseconds(10);
setPV(1);
delayMicroseconds(18);
strobe(progtime); // 20ms
delayMicroseconds(32);
setPV(0);
delayMicroseconds(12);
setRow(0);
delayMicroseconds(12);
}
//TODO - read the power down fuse bit state from the fuse map and set it only if needed
if (1) {
// disable power-down feature (JEDEC bit #5892)
setRow(0);
sendAddress(7, 125);
setPV(1);
strobe(progtime);
setPV(0);
delay(progtime);
}
}
// fuse-map writing function for 600x GAL chips
static void writeGalFuseMap600(const unsigned char* cfgArray) {
unsigned short cfgAddr = galinfo.cfgbase;
unsigned char row, bit;
unsigned short addr;
setRow(0);
for (row = 0; row < 78; row++)
{
sendBits(20, 0);
for (bit = 0; bit < 11; bit++)
sendBit(getFuseBit(7296 + 78 * bit + row));
for (bit = 0; bit < 64; bit++)
sendBit(getFuseBit(114 * bit + row));
sendBit(1);
sendAddress(7, row);
sendBits(16, 0);
setSDIN(0);
setPV(1);
strobe(progtime);
setPV(0);
}
for (row = 0; row < 64; row++)
{
for (bit = 0; bit < 20; bit++)
sendBit(getFuseBit(78 + 114 * row + bit));
sendBits(11, 0);
for (bit = 0; bit < 64; bit++)
sendBit(bit != row);
sendBits(8, 0);
for (bit = 0; bit < 16; bit++)
sendBit(getFuseBit(98 + 114 * row + bit));
setSDIN(0);
setPV(1);
strobe(progtime);
setPV(0);
}
// UES
sendBits(20, 0);
addr = galinfo.uesfuse;
for (bit = 0; bit < 72; bit++)
sendBit(getFuseBit(addr + bit));
sendBits(3, 0);
sendBit(1);
sendAddress(7, galinfo.uesrow);
sendBits(16, 0);
setSDIN(0);
setPV(1);
strobe(progtime);
setPV(0);
// CFG
setRow(galinfo.cfgrow);
for (bit = 0; bit < galinfo.cfgbits; bit++)
{
unsigned char cfgOffset = pgm_read_byte(&cfgArray[bit]); //read array byte flom flash
sendBit(getFuseBit(cfgAddr + cfgOffset));
}
setSDIN(0);
setPV(1);
strobe(progtime);
setPV(0);
}
// main fuse-map writing function
static void writeGal()
{
unsigned short i;
unsigned char* cfgArray = (unsigned char*) cfgV8;
turnOn(WRITEGAL);
switch(gal)
{
case GAL16V8:
case GAL20V8:
if (pes[2] == 0x1A || pes[2] == 0x3A) {
cfgArray = (unsigned char*) cfgV8AB;
}
writeGalFuseMapV8(cfgArray);
break;
case ATF16V8B:
case ATF20V8B:
writeGalFuseMapV8(cfgV8AB);
break;
case GAL6001:
case GAL6002:
cfgArray = (unsigned char*) galinfo.cfg;
writeGalFuseMap600(cfgArray);
break;
case GAL18V10:
case GAL20RA10:
case GAL20XV10:
case GAL26CV12:
case GAL26V12:
cfgArray = (unsigned char*) galinfo.cfg;
writeGalFuseMapV10(cfgArray, 0, 0);
break;
case GAL22V10:
case ATF22V10B:
case ATF22V10C:
writeGalFuseMapV10(cfgV10, (gal == GAL22V10) ? 0 : 1, (gal == ATF22V10C) ? 1 : 0);
break;
case ATF750C:
writeGalFuseMapV750(cfgV750);
}
turnOff();
}
// erases fuse-map in the GAL
static void eraseGAL(char eraseAll)
{
turnOn(ERASEGAL);
setPV(1);
setRow(eraseAll ? galinfo.eraseallrow : galinfo.eraserow);
if (gal == GAL16V8 || gal == ATF16V8B || gal==GAL20V8) {
sendBit(1);
}
strobe(erasetime);
setPV(0);
turnOff();
}
// sets security bit - disables fuse reading
static void secureGAL(void)
{
turnOn(WRITEGAL);
setPV(1);
strobeRow(61, BIT_ONE); // strobe row and send one bit with value 1
setPV(0);
turnOff();
}
static char checkGalTypeViaPes(void)
{
char type = UNKNOWN;
#ifdef DEBUG_PES
char i;
Serial.println(F("PES raw bytes:"));
for (i = 0; i < 10; i++) {
printFormatedNumberHex2(pes[i]);
Serial.print(F(" "));
}
Serial.println();
#endif
setFlagBit(FLAG_BIT_ATF16V8C, 0);
if (pes[7] == 'F' && pes[6]== '2' && pes[5]== '2' && (pes[4]== 'V' || pes[4]=='L') && pes[3]== '1' && pes[2]=='0') {
if (pes[1] == 'B') {
type = ATF22V10B;
} else {
type = ATF22V10C;
}
}
else if (pes[6] == 'F' && pes[5] == '2' && pes[4]== '0' && pes[3] == 'V' && pes[2]=='8' && pes[1] == 'B') {
type = ATF20V8B;
}
else if (pes[6] == 'F' && pes[5] == '1' && pes[4]== '6' && pes[3] == 'V' && pes[2]=='8') {
type = ATF16V8B;
if (pes[1] == 'C' || pes[1] == 'Z') { // ATF16V8C, ATF16V8CZ
setFlagBit(FLAG_BIT_ATF16V8C, 1);
}
}
else if (pes[8] == 'F' && pes[7] == 'V' && pes[6] == '7' && pes[5] == '5' && pes[4] == '0' && pes[3] =='C') {
// complete string at beginning of row 127: "300C057VF100"
type = ATF750C;
}
else if (pes[2] != 0x00 && pes[2] != 0xFF) {
for (type = (sizeof(galInfoList) / sizeof(galinfo_t)) - 1; type; type--) {
uint8_t id0 = pgm_read_byte(&galInfoList[type].id0);
uint8_t id1 = pgm_read_byte(&galInfoList[type].id1);
if (pes[2] == id0 || pes[2] == id1) break;
}
} else if (pes[3] == SGSTHOMSON && pes[2] == 0x00) {
type = GAL16V8;
}
return type;
}
// checks whether gal type corresponds to PES information on the IC
// note: PES must be read beforehand
static char testProperGAL(void)
{
char type = checkGalTypeViaPes();
if (type == 0) {
//Unknown or illegal PES,
goto error;
}
else if (type != gal) {
//PES indicates a different GAL type than selected. Change to detected GAL type?
goto error;
}
return 1;
error:
Serial.println(F("ER unknown or wrong GAL type (check Power ON)"));
return 0;
}
// prints a hexadecimal number - 2 digits with a leading zero
static void printFormatedNumberHex2(unsigned char num) {
if (num < 16) {
Serial.print(F("0"));
}
Serial.print(num, HEX);
}
// prints a hexadecimal number - 4 digits with a leading zero
static void printFormatedNumberHex4(unsigned short num) {
if (num < 0x10) {
Serial.print(F("000"));
} else
if (num < 0x100) {
Serial.print(F("00"));
} else
if (num < 0x1000) {
Serial.print(F("0"));
}
Serial.print(num, HEX);
}
// prints a decimal number - 4 digits with a leading zero
static void printFormatedNumberDec4(unsigned short num) {
if (num < 1) {
Serial.print(F("0000"));
return;
}
if (num < 10) {
Serial.print(F("000"));
} else
if (num < 100) {
Serial.print(F("00"));
} else
if (num < 1000) {
Serial.print(F("0"));
}
Serial.print(num, DEC);
}
// adds a formated decimal number with a leading zero to a line buffer at position 'i'
static unsigned char addFormatedNumberDec4(unsigned short num, unsigned char i) {
char cnt = 3;
while (cnt >= 0) {
line[i + cnt] = '0' + (num % 10);
num /= 10;
cnt--;
}
return i + 4;
}
// calculates fuse-map checksum and returns it
static unsigned short checkSum(unsigned short n)
{
unsigned short c, e, i;
unsigned long a;
c = e= 0;
a = 0;
for (i = 0; i < n; i++) {
e++;
if (e == 9) {
e = 1;
a += c;
c = 0;
}
c >>= 1;
if (getFuseBit(i)) {
c += 0x80;
}
}
return (unsigned short)((c >> (8 - e)) + a);
}
static void printGalName() {
switch (gal) {
case GAL16V8: Serial.println(F("GAL16V8")); break;
case GAL18V10: Serial.println(F("GAL18V10")); break;
case GAL20V8: Serial.println(F("GAL20V8")); break;
case GAL20RA10: Serial.println(F("GAL20RA10")); break;
case GAL20XV10: Serial.println(F("GAL20XV10")); break;
case GAL22V10: Serial.println(F("GAL22V10")); break;
case GAL26CV12: Serial.println(F("GAL26CV12")); break;
case GAL26V12: Serial.println(F("GAL26V12")); break;
case GAL6001: Serial.println(F("GAL6001")); break;
case GAL6002: Serial.println(F("GAL6002")); break;
case ATF16V8B:
if (flagBits & FLAG_BIT_ATF16V8C) {
Serial.println(F("ATF16V8C"));
} else {
Serial.println(F("ATF16V8B"));
}
break;
case ATF20V8B: Serial.println(F("ATF20V8B")); break;
case ATF22V10B: Serial.println(F("ATF22V10B")); break;
case ATF22V10C: Serial.println(F("ATF22V10C")); break;
case ATF750C: Serial.println(F("ATF750C")); break;
default: Serial.println(F("GAL")); break;
}
}
static unsigned printJedecBlock(unsigned short k, unsigned short bits, unsigned short rows) {
unsigned short i, j;
unsigned char unused;
for (i = 0; i < bits; i++)
{
unused = 1;
for (j = 0; j < rows; j++)
{
unused &= !getFuseBit(k + j);
}
if (unused) {
k += rows;
continue;
}
Serial.print('L');
printFormatedNumberDec4(k);
Serial.print(' ');
for (j = 0; j < rows; j++, k++)
{
if (getFuseBit(k)) {
unused = 0;
Serial.print('1');
} else {
Serial.print('0');
}
}
Serial.println('*');
}
return k;
}
// prints the contents of fuse-map array in the form of JEDEC text file
static void printJedec()
{
unsigned short i, j, k, n;
unsigned char unused, start;
uint8_t apdFuse = (flagBits & FLAG_BIT_APD) ? 1 : 0;
Serial.print(F("JEDEC file for "));
printGalName();
Serial.print(F("*QP")); Serial.print(galinfo.pins, DEC);
Serial.print(F("*QF")); Serial.print(galinfo.fuses + apdFuse, DEC);
Serial.println(F("*QV0*F0*G0*X0*"));
k = 0;
if (gal == GAL6001 || gal == GAL6002) {
k = printJedecBlock(k, 64, 114);
k = printJedecBlock(k, 11, 78);
} else {
k = printJedecBlock(k, galinfo.bits, galinfo.rows);
}
if( k < galinfo.uesfuse) {
Serial.print('L');
printFormatedNumberDec4(k);
Serial.print(' ');
while(k < galinfo.uesfuse) {
if (getFuseBit(k)) {
unused = 0;
Serial.print('1');
} else {
Serial.print('0');
}
k++;
}
Serial.println('*');
}
// UES in byte form
Serial.print(F("N UES"));
for (j = 0;j < galinfo.uesbytes; j++) {
n = 0;
for (i = 0; i < 8; i++) {
if (getFuseBit(k + 8 * j + i)) {
if (gal == ATF22V10C || gal == ATF750C) {
n |= 1 << (7 - i); // big-endian
}
else {
n |= 1 << i; // little-endian
}
}
}
Serial.print(' ');
printFormatedNumberHex2(n);
}
Serial.println('*');
// UES in bit form
Serial.print('L');
printFormatedNumberDec4(k);
Serial.print(' ');
for(j = 0; j < 8 * galinfo.uesbytes; j++) {
if (getFuseBit(k++)) {
Serial.print('1');
} else {
Serial.print('0');
}
}
Serial.println('*');
// CFG bits
if (k < galinfo.fuses) {
Serial.print('L');
printFormatedNumberDec4(k);
Serial.print(' ');
while( k < galinfo.fuses) {
if (getFuseBit(k++)) {
Serial.print('1');
} else {
Serial.print('0');
}
}
//ATF16V8C
if (apdFuse) {
Serial.print('1');
setFuseBit(k); // set for correct check-sum calculation
}
Serial.println('*');
} else if (apdFuse) { //ATF22V10C
Serial.print('L');
printFormatedNumberDec4(k);
Serial.println(F(" 1*"));
setFuseBit(k); // set for correct check-sum calculation
}
Serial.print(F("N PES"));
for(i = 0; i < galinfo.pesbytes; i++) {
Serial.print(' ');
printFormatedNumberHex2(pes[i]);
}
Serial.println('*');
Serial.print('C');
printFormatedNumberHex4(checkSum(galinfo.fuses + apdFuse));
Serial.println();
Serial.println('*');
}
// helper print function to save RAM space
static void printNoFusesError() {
Serial.println(F("ER fuse map not uploaded"));
}
static void testVoltage(int seconds) {
int i;
// New board design: set VPP to 16.5V and measure values
// on analogue pin A1
if (varVppExists) {
int16_t v;
uint8_t okCnt = 0;
varVppSetMax();
for (i = 0 ; i < seconds; i++) {
delay(1000);
v = varVppMeasureVpp(1); //measure and print
if (v >= 1640 && v <= 1664) {
okCnt++;
// stop early if the VPP is set correctly (still allow time for POT fine-tuning)
if (okCnt > 3) {
Serial.println(F("VPP OK"));
i = seconds;
}
} else {
okCnt = 0;
}
}
varVppSet(VPP_5V0);
}
// Legacy board design: set the VPP_EN pin "On" and check
// with multimeter the desired VPP voltage specific for GAL chip.
else {
pinMode(PIN_VPP, OUTPUT);
setVPP(1);
for (i = 0 ; i < seconds; i++) {
delay(1000);
}
setVPP(0);
pinMode(PIN_VPP, INPUT);
}
}
// returns 1 if type check if OK, 0 if gal type does not match the type read from PES
static char doTypeCheck(void) {
if (0 == flagBits & FLAG_BIT_TYPE_CHECK) {
setGalDefaults();
return 1; // no need to do type check
}
readPes();
parsePes(UNKNOWN);
return testProperGAL();
}
static void measureVpp(uint8_t index) {
varVppSet(index);
delay(150);
varVppMeasureVpp(1); //print measured value
delay(5000);
}
static void measureVppValues(void) {
if (!varVppExists) {
Serial.println(F("ER variable VPP not supported"));
return;
}
Serial.print(F("VPP calib. offset: "));
Serial.println(calOffset);
Serial.print(F("VPP: 4.2 - 5.0V : "));
measureVpp(VPP_5V0);
Serial.print(F("VPP: 9.0V : "));
measureVpp(VPP_9V0);
Serial.print(F("VPP: 10.0V : "));
measureVpp(VPP_10V0);
Serial.print(F("VPP: 12.0V : "));
measureVpp(VPP_12V0);
Serial.print(F("VPP: 14.0V : "));
measureVpp(VPP_14V0);
Serial.print(F("VPP: 16.0V : "));
measureVpp(VPP_16V0);
varVppSet(VPP_5V0);
}
static void calibrateVpp(void) {
if (!varVppExists) {
Serial.println(F("ER variable VPP not supported"));
return;
}
if (varVppCalibrate()) {
Serial.println(F("Calibration OK"));
}
}
static void startJtagPlayer(uint8_t vpp) {
jtag_port_t jport;
//assign jtag pins
jport.tms = 12;
jport.tdi = 2;
jport.tdo = 4;
jport.tck = 3;
jport.vref = 10;
//Serial.println(vpp ? F("JTAG VPP 1"): F("JTAG VPP 0"));
// ensure PC app is ready
delay(200);
// set VPP if required
if (varVppExists) {
varVppSet(vpp ? VPP_11V0 : VPP_5V0);
}
// start XSVF player / processor
jtag_play_xsvf(&jport);
// unset VPP
if (varVppExists) {
varVppSet(VPP_5V0);
}
}
// Arduino main loop
void loop() {
// read a command from serial terminal or COMMAND_NONE if nothing is received from serial
char command = handleTerminalCommands();
// any unexpected input when uploading fuse map terminates the upload process
if (isUploading && command != COMMAND_UTX && command != COMMAND_NONE) {
Serial.println(F("ER upload aborted"));
isUploading = 0;
lineIndex = 0;
}
// handle commands received from the serial terminal
switch (command) {
// print some help
case COMMAND_HELP: {
printHelp(1);
} break;
case COMMAND_IDENTIFY_PROGRAMMER : {
printHelp(0);
} break;
// verify fuse-map bits and bits read from the GAL chip
case COMMAND_VERIFY_FUSES: {
if (mapUploaded) {
if (doTypeCheck()) {
readOrVerifyGal(1); //just verify, do not overwrite fusemap
}
} else {
printNoFusesError();
}
} break;
// handle upload command - start the download of fuse-map
case COMMAND_UPLOAD: {
short i;
// clean fuses
for (i = 0; i < MAXFUSES; i++) {
fusemap[i] = 0;
}
sparseSetup(1);
isUploading = 1;
uploadError = 0;
} break;
// command of the upload protocol
case COMMAND_UTX : {
parseUploadLine();
} break;
// read and print the PES
case COMMAND_READ_PES : {
char type;
readPes();
type = checkGalTypeViaPes();
parsePes(type);
printPes(type);
} break;
case COMMAND_WRITE_PES : {
char type;
type = checkGalTypeViaPes();
parsePes(type);
writePes();
} break;
// read fuse-map from the GAL and print it in the JEDEC form
case COMMAND_READ_FUSES : {
if (doTypeCheck()) {
readOrVerifyGal(0); //just read, no verification
printJedec();
}
} break;
// write current fuse-map to the GAL chip
case COMMAND_WRITE_FUSES : {
if (mapUploaded) {
if (doTypeCheck()) {
writeGal();
//security is handled by COMMAND_ENABLE_SECURITY command
}
} else {
printNoFusesError();
}
} break;
// erases the fuse-map on the GAL chip
case COMMAND_ERASE_GAL: {
if (doTypeCheck()) {
eraseGAL(0);
}
} break;
// erases PES and the fuse-map on the GAL chip
case COMMAND_ERASE_GAL_ALL: {
if (doTypeCheck()) {
eraseGAL(1);
}
} break;
// sets the security bit
case COMMAND_ENABLE_SECURITY: {
if (doTypeCheck()) {
secureGAL();
}
} break;
// keep atmel power-down feature enabled during write
case COMMAND_ENABLE_APD: {
setFlagBit(FLAG_BIT_APD, 1);
Serial.println(F("OK APD set"));
} break;
case COMMAND_DISABLE_APD: {
setFlagBit(FLAG_BIT_APD, 0);
Serial.println(F("OK APD cleared"));
} break;
// toggles terminal echo
case COMMAND_ECHO : {
echoEnabled = 1 - echoEnabled;
} break;
case COMMAND_TEST_VOLTAGE : {
testVoltage(20);
} break;
case COMMAND_SET_GAL_TYPE : {
char type = line[1] - '0';
if (type >= 1 && type < LAST_GAL_TYPE) {
gal = (GALTYPE) type;
copyGalInfo();
if (0 == flagBits & FLAG_BIT_TYPE_CHECK) { //no type check requested
setGalDefaults();
}
} else {
Serial.print(F("ER Unknown gal type "));
Serial.println(type, DEC);
}
} break;
case COMMAND_ENABLE_CHECK_TYPE: {
setFlagBit(FLAG_BIT_TYPE_CHECK, 1);
} break;
case COMMAND_DISABLE_CHECK_TYPE: {
int i = 0;
while(i < 12){
pes[i++] = 0;
}
setFlagBit(FLAG_BIT_TYPE_CHECK, 0);
} break;
case COMMAND_MEASURE_VPP: {
measureVppValues();
} break;
// calibration offset helps to offset the resistor tolerances in voltage dividers and also
// small differences in analog ref which is ~3.3 V derived from LDO.
case COMMAND_CALIBRATION_OFFSET: {
int8_t offset = line[1] - '0';
if (offset >=0 && offset <= 64) {
//0:-0.32V 1:-0.31V 2: -0.30V ... 32:0V 33:0.01V 34: 0.02V ... 64:0.32V
calOffset = offset - 32;
Serial.print(F("Using cal offset: "));
Serial.println(calOffset);
} else {
Serial.println(F("ER: cal offset failed"));
}
} break;
case COMMAND_CALIBRATE_VPP: {
calibrateVpp();
} break;
case COMMAND_JTAG_PLAYER: {
startJtagPlayer(line[1] == '1');
//flush the serial line in case the player ended abruptly
readGarbage();
} break;
default: {
if (command != COMMAND_NONE) {
Serial.print(F("ER Unknown command: "));
Serial.println(line);
}
}
}
// display prompt character - important for the PC program to check that Arduino
// finished the desired operation
if (command != COMMAND_NONE) {
Serial.println(F(">"));
}
// and that's it!
}