unified_retro_keyboard/hardware/apple2-encoder
Dave 5e4c1ed078 Fix shunted diode footprints on encoder boards
The encoder boards (ATmega328P, Atmega2560, Apple2(2560) can accomodate
keyboard matrices with no diodes, by adding per-row diodes on the
encoder board.  For keyboards with per-key diodes (the typical use
case), the per-row diodes are not needed, and therefore the footprints
should be shunted by default, using a special shunted diode footprint.
When diodes are installed, the shunt can be cut with an x-acto knife.
Previous board revs had the correct footprint, but somehow the regular
diode footprint was substituted on the last release of each of these
PCBS.  The correct footprint has been restored.
2021-08-08 13:16:38 -05:00
..
images
apple-encoder-bom.xlsx
apple-encoder.kicad_pcb Fix shunted diode footprints on encoder boards 2021-08-08 13:16:38 -05:00
apple-encoder.pro
apple-encoder.sch Fix shunted diode footprints on encoder boards 2021-08-08 13:16:38 -05:00
README.md Update README.md 2021-01-15 22:49:34 -06:00

Apple II/II+ Encoder

This is a version of the ASCII interface wired up to be compatible with the Apple II/Apple II+ keyboard matrix. This board was broken out as a separate PCB from the Atmega2560-based interface board on which it was based, in order to keep the "custom" connector customizable on that board.

This board is otherwise identical to rev 3.4 of the ATMega2560-based ASCII interface board, and shares the same firmware and features.

Assembly Rendering

Features

  • Parallel or serial output
  • Up to 8 configuration settings via an up-to-8 position DIP switch
  • Apple 1, Apple 2, and SOL-20 compatible outputs. Other configurations can be supported by making a custom cable.
  • Can decode arbitrary keyboards up 16 rows by 8 columns.
  • Supports up to 3 keyboard LEDs
  • Supports up to 3 "special" host outputs, such as RESET, SCREEN_CLEAR, BREAK, etc.
  • Socket for custom connector

Assembly Notes

  • You may build this board as if it is a general purpose ASCII interface. In that case, you may want to avoid installing the 1x25 Apple2 keyboard header if it interferes with the target keyboard matrix.

  • This encoder is normally used with keyboards that have a diode per key. For use with a key matrix with no diodes (such as the Apple 2 key matrix), cut the PCB traces that short diodes D1-16, and install D1-16.

  • If you ARE building this board as an Apple 2 encoder, then you may OMIT:

    • Sol-20 connector J5
    • Custom connector J7
    • D17,D18,D19 - These are used for the "classic" keyboard matrix.
    • D7,D8,D15,D16 - These are diodes for rows 12-15, which are not used.
    • The serial out connector J3 if you do not plan to use a serial output.
    • The I/O connector J4, as all the I/O lines are routed through the keyboard connector.
    • If you will be using the keyboard with only an Apple 1 or Apple 2, then you do not need to install both the Apple 2 connector (J1) AND the Apple 1 connector (J2). You may install only the one you plan to use, and reduce the risk of plugging into the wrong socket (and possibly damaging the encoder).
  1. Solder the surface-mount microcontroller first. Be sure to match pin 1 to the dot on the silk-screen layer.
  2. Next, install the surface mount crystal, Y1. The orientation is not important.
  3. Next, solder in the resitor R1
  4. Install all the capacitors. Be sure to separate out the two capacitors for the XTAL circuit from the other capacitors, the rest of which are 0.1uF bypass capacitors.
  5. Install the In-circuit Serial Programming (ISP) header, J6. (right-angle, 2x3 0.100")
  6. If you will be using the Apple 1 connector, install the DIP socket J1 (16-pin dip). If you plan to insert and remove the cable many times, a dual-wipe socket may be preferable to machine-pin, since it has a lower insertion force, and you will be less likely to bend pins. If you plan to insert the cable once and leave it forever, I suggest a machine-pin DIP socket.
  7. If you will be using the Apple 2 connector, install the DIP socket J2 (16-pin dip). The note for the Apple 1 connector selection applies here as well.