contiki/dev/enc28j60/enc28j60.c

645 lines
20 KiB
C
Raw Normal View History

2014-06-03 20:40:55 +00:00
/*
* Copyright (c) 2012-2013, Thingsquare, http://www.thingsquare.com/.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the copyright holder nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
* OF THE POSSIBILITY OF SUCH DAMAGE.
*
*/
#include "contiki.h"
#include "enc28j60.h"
#include <stdio.h>
#include <string.h>
#define DEBUG 0
#if DEBUG
#define PRINTF(...) printf(__VA_ARGS__)
#else
#define PRINTF(...)
#endif
#define EIE 0x1b
#define EIR 0x1c
#define ESTAT 0x1d
#define ECON2 0x1e
#define ECON1 0x1f
#define ESTAT_CLKRDY 0x01
#define ESTAT_TXABRT 0x02
#define ECON1_RXEN 0x04
#define ECON1_TXRTS 0x08
#define ECON2_AUTOINC 0x80
#define ECON2_PKTDEC 0x40
#define EIR_TXIF 0x08
#define ERXTX_BANK 0x00
#define ERDPTL 0x00
#define ERDPTH 0x01
#define EWRPTL 0x02
#define EWRPTH 0x03
#define ETXSTL 0x04
#define ETXSTH 0x05
#define ETXNDL 0x06
#define ETXNDH 0x07
#define ERXSTL 0x08
#define ERXSTH 0x09
#define ERXNDL 0x0a
#define ERXNDH 0x0b
#define ERXRDPTL 0x0c
#define ERXRDPTH 0x0d
#define RX_BUF_START 0x0000
#define RX_BUF_END 0x0fff
#define TX_BUF_START 0x1200
/* MACONx registers are in bank 2 */
#define MACONX_BANK 0x02
#define MACON1 0x00
#define MACON2 0x01
#define MACON3 0x02
#define MACON4 0x03
#define MABBIPG 0x04
#define MAIPGL 0x06
#define MAIPGH 0x07
#define MAMXFLL 0x0a
#define MAMXFLH 0x0b
#define MACON1_TXPAUS 0x08
#define MACON1_RXPAUS 0x04
#define MACON1_MARXEN 0x01
#define MACON2_MARST 0x80
#define MACON3_PADCFG_FULL 0xe0
#define MACON3_TXCRCEN 0x10
#define MACON3_FRMLNEN 0x02
#define MACON3_FULDPX 0x01
#define MAX_MAC_LENGTH 1518
#define MAADRX_BANK 0x03
#define MAADR1 0x04 /* MAADR<47:40> */
#define MAADR2 0x05 /* MAADR<39:32> */
#define MAADR3 0x02 /* MAADR<31:24> */
#define MAADR4 0x03 /* MAADR<23:16> */
#define MAADR5 0x00 /* MAADR<15:8> */
#define MAADR6 0x01 /* MAADR<7:0> */
#define EPKTCNT_BANK 0x01
#define ERXFCON 0x18
#define EPKTCNT 0x19
#define ERXFCON_UCEN 0x80
#define ERXFCON_ANDOR 0x40
#define ERXFCON_CRCEN 0x20
#define ERXFCON_MCEN 0x02
#define ERXFCON_BCEN 0x01
PROCESS(enc_watchdog_process, "Enc28j60 watchdog");
static uint8_t initialized = 0;
static uint8_t enc_mac_addr[6];
static int received_packets = 0;
static int sent_packets = 0;
/*---------------------------------------------------------------------------*/
static uint8_t
readreg(uint8_t reg)
{
uint8_t r;
enc28j60_arch_spi_select();
enc28j60_arch_spi_write(0x00 | (reg & 0x1f));
r = enc28j60_arch_spi_read();
enc28j60_arch_spi_deselect();
return r;
}
/*---------------------------------------------------------------------------*/
static void
writereg(uint8_t reg, uint8_t data)
{
enc28j60_arch_spi_select();
enc28j60_arch_spi_write(0x40 | (reg & 0x1f));
enc28j60_arch_spi_write(data);
enc28j60_arch_spi_deselect();
}
/*---------------------------------------------------------------------------*/
static void
setregbank(uint8_t bank)
{
writereg(ECON1, (readreg(ECON1) & 0xfc) | (bank & 0x03));
}
/*---------------------------------------------------------------------------*/
static void
writedatabyte(uint8_t byte)
{
enc28j60_arch_spi_select();
/* The Write Buffer Memory (WBM) command is 0 1 1 1 1 0 1 0 */
enc28j60_arch_spi_write(0x7a);
enc28j60_arch_spi_write(byte);
enc28j60_arch_spi_deselect();
}
/*---------------------------------------------------------------------------*/
static void
writedata(uint8_t *data, int datalen)
{
int i;
enc28j60_arch_spi_select();
/* The Write Buffer Memory (WBM) command is 0 1 1 1 1 0 1 0 */
enc28j60_arch_spi_write(0x7a);
for(i = 0; i < datalen; i++) {
enc28j60_arch_spi_write(data[i]);
}
enc28j60_arch_spi_deselect();
}
/*---------------------------------------------------------------------------*/
static uint8_t
readdatabyte(void)
{
uint8_t r;
enc28j60_arch_spi_select();
/* THe Read Buffer Memory (RBM) command is 0 0 1 1 1 0 1 0 */
enc28j60_arch_spi_write(0x3a);
r = enc28j60_arch_spi_read();
enc28j60_arch_spi_deselect();
return r;
}
/*---------------------------------------------------------------------------*/
static int
readdata(uint8_t *buf, int len)
{
int i;
enc28j60_arch_spi_select();
/* THe Read Buffer Memory (RBM) command is 0 0 1 1 1 0 1 0 */
enc28j60_arch_spi_write(0x3a);
for(i = 0; i < len; i++) {
buf[i] = enc28j60_arch_spi_read();
}
enc28j60_arch_spi_deselect();
return i;
}
/*---------------------------------------------------------------------------*/
static void
softreset(void)
{
enc28j60_arch_spi_select();
/* The System Command (soft reset) is 1 1 1 1 1 1 1 1 */
enc28j60_arch_spi_write(0xff);
enc28j60_arch_spi_deselect();
}
/*---------------------------------------------------------------------------*/
static void
reset(void)
{
PRINTF("enc28j60: resetting chip\n");
enc28j60_arch_spi_init();
/*
6.0 INITIALIZATION
Before the ENC28J60 can be used to transmit and receive packets,
certain device settings must be initialized. Depending on the
application, some configuration options may need to be
changed. Normally, these tasks may be accomplished once after
Reset and do not need to be changed thereafter.
6.1 Receive Buffer
Before receiving any packets, the receive buffer must be
initialized by programming the ERXST and ERXND pointers. All
memory between and including the ERXST and ERXND addresses will be
dedicated to the receive hardware. It is recommended that the
ERXST pointer be programmed with an even address.
Applications expecting large amounts of data and frequent packet
delivery may wish to allocate most of the memory as the receive
buffer. Applications that may need to save older packets or have
several packets ready for transmission should allocate less
memory.
When programming the ERXST pointer, the ERXWRPT registers will
automatically be updated with the same values. The address in
ERXWRPT will be used as the starting location when the receive
hardware begins writing received data. For tracking purposes, the
ERXRDPT registers should additionally be programmed with the same
value. To program ERXRDPT, the host controller must write to
ERXRDPTL first, followed by ERXRDPTH. See Section 7.2.4 Freeing
Receive Buffer Space for more information
6.2 Transmission Buffer
All memory which is not used by the receive buffer is considered
the transmission buffer. Data which is to be transmitted should be
written into any unused space. After a packet is transmitted,
however, the hardware will write a seven-byte status vector into
memory after the last byte in the packet. Therefore, the host
controller should leave at least seven bytes between each packet
and the beginning of the receive buffer. No explicit action is
required to initialize the transmission buffer.
6.3 Receive Filters
The appropriate receive filters should be enabled or disabled by
writing to the ERXFCON register. See Section 8.0 Receive Filters
for information on how to configure it.
6.4 Waiting For OST
If the initialization procedure is being executed immediately
following a Power-on Reset, the ESTAT.CLKRDY bit should be polled
to make certain that enough time has elapsed before proceeding to
modify the MAC and PHY registers. For more information on the OST,
see Section 2.2 Oscillator Start-up Timer.
*/
/* Wait for OST */
while((readreg(ESTAT) & ESTAT_CLKRDY) == 0);
softreset();
setregbank(ERXTX_BANK);
/* Set up receive buffer */
writereg(ERXSTL, RX_BUF_START & 0xff);
writereg(ERXSTH, RX_BUF_START >> 8);
writereg(ERXNDL, RX_BUF_END & 0xff);
writereg(ERXNDH, RX_BUF_END >> 8);
writereg(ERDPTL, RX_BUF_START & 0xff);
writereg(ERDPTH, RX_BUF_START >> 8);
writereg(ERXRDPTL, RX_BUF_START & 0xff);
writereg(ERXRDPTH, RX_BUF_START >> 8);
/* Receive filters */
setregbank(EPKTCNT_BANK);
/* writereg(ERXFCON, ERXFCON_UCEN | ERXFCON_CRCEN |
ERXFCON_MCEN | ERXFCON_BCEN);*/
/* XXX: can't seem to get the unicast filter to work right now,
using promiscous mode for now. */
writereg(ERXFCON, 0);
/*
6.5 MAC Initialization Settings
Several of the MAC registers require configuration during
initialization. This only needs to be done once; the order of
programming is unimportant.
1. Clear the MARST bit in MACON2 to pull the MAC out of Reset.
2. Set the MARXEN bit in MACON1 to enable the MAC to receive
frames. If using full duplex, most applications should also set
TXPAUS and RXPAUS to allow IEEE defined flow control to function.
3. Configure the PADCFG, TXCRCEN and FULDPX bits of MACON3. Most
applications should enable automatic padding to at least 60 bytes
and always append a valid CRC. For convenience, many applications
may wish to set the FRMLNEN bit as well to enable frame length
status reporting. The FULDPX bit should be set if the application
will be connected to a full-duplex configured remote node;
otherwise, it should be left clear.
4. Configure the bits in MACON4. Many applications may not need to
modify the Reset default.
5. Program the MAMXFL registers with the maximum frame length to
be permitted to be received or transmitted. Normal network nodes
are designed to handle packets that are 1518 bytes or less.
6. Configure the Back-to-Back Inter-Packet Gap register,
MABBIPG. Most applications will program this register with 15h
when Full-Duplex mode is used and 12h when Half-Duplex mode is
used.
7. Configure the Non-Back-to-Back Inter-Packet Gap register low
byte, MAIPGL. Most applications will program this register with
12h.
8. If half duplex is used, the Non-Back-to-Back Inter-Packet Gap
register high byte, MAIPGH, should be programmed. Most
applications will program this register to 0Ch.
9. If Half-Duplex mode is used, program the Retransmission and
Collision Window registers, MACLCON1 and MACLCON2. Most
applications will not need to change the default Reset values. If
the network is spread over exceptionally long cables, the default
value of MACLCON2 may need to be increased.
10. Program the local MAC address into the
MAADR0:MAADR5 registers.
*/
setregbank(MACONX_BANK);
/* Pull MAC out of reset */
writereg(MACON2, 0);//readreg(MACON2) & (~MACON2_MARST));
/* Turn on reception and IEEE-defined flow control */
writereg(MACON1, readreg(MACON1) | (MACON1_MARXEN + MACON1_TXPAUS +
MACON1_RXPAUS));
/* Set padding, crc, full duplex */
writereg(MACON3, readreg(MACON3) | (MACON3_PADCFG_FULL + MACON3_TXCRCEN +
MACON3_FULDPX + MACON3_FRMLNEN));
/* Don't modify MACON4 */
/* Set maximum frame length in MAMXFL */
writereg(MAMXFLL, MAX_MAC_LENGTH & 0xff);
writereg(MAMXFLH, MAX_MAC_LENGTH >> 8);
/* Set back-to-back inter packet gap */
writereg(MABBIPG, 0x15);
/* Set non-back-to-back packet gap */
writereg(MAIPGL, 0x12);
writereg(MAIPGH, 0x0c);
/* Set MAC address */
setregbank(MAADRX_BANK);
writereg(MAADR6, enc_mac_addr[5]);
writereg(MAADR5, enc_mac_addr[4]);
writereg(MAADR4, enc_mac_addr[3]);
writereg(MAADR3, enc_mac_addr[2]);
writereg(MAADR2, enc_mac_addr[1]);
writereg(MAADR1, enc_mac_addr[0]);
/* Receive filters */
setregbank(EPKTCNT_BANK);
writereg(ERXFCON, ERXFCON_UCEN | ERXFCON_CRCEN | ERXFCON_BCEN);
/*
6.6 PHY Initialization Settings
Depending on the application, bits in three of the PHY modules
registers may also require configuration. The PHCON1.PDPXMD bit
partially controls the devices half/full-duplex
configuration. Normally, this bit is initialized correctly by the
external circuitry (see Section 2.6 LED Configuration). If the
external circuitry is not present or incorrect, however, the host
controller must program the bit properly. Alternatively, for an
externally configurable system, the PDPXMD bit may be read and the
FULDPX bit be programmed to match.
For proper duplex operation, the PHCON1.PDPXMD bit must also match
the value of the MACON3.FULDPX bit.
If using half duplex, the host controller may wish to set the
PHCON2.HDLDIS bit to prevent automatic loopback of the data which
is transmitted. The PHY register, PHLCON, controls the outputs of
LEDA and LEDB. If an application requires a LED configuration
other than the default, PHLCON must be altered to match the new
requirements. The settings for LED operation are discussed in
Section 2.6 LED Configuration. The PHLCON register is shown in
Register 2-2 (page 9).
*/
/* Don't worry about PHY configuration for now */
/* Turn on autoincrement for buffer access */
writereg(ECON2, readreg(ECON2) | ECON2_AUTOINC);
/* Turn on reception */
writereg(ECON1, ECON1_RXEN);
}
/*---------------------------------------------------------------------------*/
void
enc28j60_init(uint8_t *mac_addr)
{
if(initialized) {
return;
}
memcpy(enc_mac_addr, mac_addr, 6);
/* Start watchdog process */
process_start(&enc_watchdog_process, NULL);
reset();
initialized = 1;
}
/*---------------------------------------------------------------------------*/
int
enc28j60_send(uint8_t *data, uint16_t datalen)
{
int padding = 0;
if(!initialized) {
return -1;
}
/*
1. Appropriately program the ETXST pointer to point to an unused
location in memory. It will point to the per packet control
byte. In the example, it would be programmed to 0120h. It is
recommended that an even address be used for ETXST.
2. Use the WBM SPI command to write the per packet control byte,
the destination address, the source MAC address, the
type/length and the data payload.
3. Appropriately program the ETXND pointer. It should point to the
last byte in the data payload. In the example, it would be
programmed to 0156h.
4. Clear EIR.TXIF, set EIE.TXIE and set EIE.INTIE to enable an
interrupt when done (if desired).
5. Start the transmission process by setting
ECON1.TXRTS.
*/
setregbank(ERXTX_BANK);
/* Set up the transmit buffer pointer */
writereg(ETXSTL, TX_BUF_START & 0xff);
writereg(ETXSTH, TX_BUF_START >> 8);
writereg(EWRPTL, TX_BUF_START & 0xff);
writereg(EWRPTH, TX_BUF_START >> 8);
/* Write the transmission control register as the first byte of the
output packet. We write 0x00 to indicate that the default
configuration (the values in MACON3) will be used. */
#define WITH_MANUAL_PADDING 1
#if WITH_MANUAL_PADDING
#define PADDING_MIN_SIZE 60
writedatabyte(0x0B); /* POVERRIDE, PCRCEN, PHUGEEN. Not PPADEN */
if(datalen < PADDING_MIN_SIZE) {
padding = PADDING_MIN_SIZE - datalen;
} else {
padding = 0;
}
#else /* WITH_MANUAL_PADDING */
writedatabyte(0x00); /* MACON3 */
padding = 0;
#endif /* WITH_MANUAL_PADDING */
/* Write a pointer to the last data byte. */
writereg(ETXNDL, (TX_BUF_START + datalen + 0 + padding) & 0xff);
writereg(ETXNDH, (TX_BUF_START + datalen + 0 + padding) >> 8);
writedata(data, datalen);
if(padding > 0) {
uint8_t padding_buf[60];
memset(padding_buf, 0, padding);
writedata(padding_buf, padding);
}
/* Clear EIR.TXIF */
writereg(EIR, readreg(EIR) & (~EIR_TXIF));
/* Don't care about interrupts for now */
/* Send the packet */
writereg(ECON1, readreg(ECON1) | ECON1_TXRTS);
while((readreg(ECON1) & ECON1_TXRTS) > 0);
if((readreg(ESTAT) & ESTAT_TXABRT) != 0) {
PRINTF("enc28j60: tx err: %d: %02x:%02x:%02x:%02x:%02x:%02x\n", datalen,
0xff & data[0], 0xff & data[1], 0xff & data[2],
0xff & data[3], 0xff & data[4], 0xff & data[5]);
} else {
PRINTF("enc28j60: tx: %d: %02x:%02x:%02x:%02x:%02x:%02x\n", datalen,
0xff & data[0], 0xff & data[1], 0xff & data[2],
0xff & data[3], 0xff & data[4], 0xff & data[5]);
}
sent_packets++;
PRINTF("enc28j60: sent_packets %d\n", sent_packets);
return datalen;
}
/*---------------------------------------------------------------------------*/
int
enc28j60_read(uint8_t *buffer, uint16_t bufsize)
{
int n, len, next, err;
uint8_t nxtpkt[2];
uint8_t status[2];
uint8_t length[2];
err = 0;
setregbank(EPKTCNT_BANK);
n = readreg(EPKTCNT);
if(n == 0) {
return 0;
}
PRINTF("enc28j60: EPKTCNT 0x%02x\n", n);
setregbank(ERXTX_BANK);
/* Read the next packet pointer */
nxtpkt[0] = readdatabyte();
nxtpkt[1] = readdatabyte();
PRINTF("enc28j60: nxtpkt 0x%02x%02x\n", nxtpkt[1], nxtpkt[0]);
length[0] = readdatabyte();
length[1] = readdatabyte();
PRINTF("enc28j60: length 0x%02x%02x\n", length[1], length[0]);
status[0] = readdatabyte();
status[1] = readdatabyte();
/* This statement is just to avoid a compiler warning: */
status[0] = status[0];
PRINTF("enc28j60: status 0x%02x%02x\n", status[1], status[0]);
len = (length[1] << 8) + length[0];
if(bufsize >= len) {
readdata(buffer, len);
} else {
uint16_t i;
err = 1;
/* flush rx fifo */
for(i = 0; i < len; i++) {
readdatabyte();
}
}
/* Read an additional byte at odd lengths, to avoid FIFO corruption */
if((len % 2) != 0) {
readdatabyte();
}
/* Errata #14 */
next = (nxtpkt[1] << 8) + nxtpkt[0];
if(next == RX_BUF_START) {
next = RX_BUF_END;
} else {
next = next - 1;
}
writereg(ERXRDPTL, next & 0xff);
writereg(ERXRDPTH, next >> 8);
writereg(ECON2, readreg(ECON2) | ECON2_PKTDEC);
if(err) {
PRINTF("enc28j60: rx err: flushed %d\n", len);
return 0;
}
PRINTF("enc28j60: rx: %d: %02x:%02x:%02x:%02x:%02x:%02x\n", len,
0xff & buffer[0], 0xff & buffer[1], 0xff & buffer[2],
0xff & buffer[3], 0xff & buffer[4], 0xff & buffer[5]);
received_packets++;
PRINTF("enc28j60: received_packets %d\n", received_packets);
return len;
}
/*---------------------------------------------------------------------------*/
PROCESS_THREAD(enc_watchdog_process, ev, data)
{
static struct etimer et;
PROCESS_BEGIN();
while(1) {
#define RESET_PERIOD (30 * CLOCK_SECOND)
etimer_set(&et, RESET_PERIOD);
PROCESS_WAIT_EVENT_UNTIL(etimer_expired(&et));
PRINTF("enc28j60: test received_packet %d > sent_packets %d\n", received_packets, sent_packets);
if(received_packets <= sent_packets) {
PRINTF("enc28j60: resetting chip\n");
reset();
}
received_packets = 0;
sent_packets = 0;
}
PROCESS_END();
}
/*---------------------------------------------------------------------------*/