contiki/platform/sensinode/Makefile.sensinode

# Sensinode CC2430 platform makefile
# Supported products: N100, N600, N601, N710, N711
# Support for N740 is experimental.

# We support defines for product models using the following format
# e.g. MODEL_N601. Run make TARGET=sensinode DEFINES=MODEL_N601 to 
# automatically configure the correct LED, button, UART etc. settings
# for that product model. If undefined, MODEL_N100 is chosen by default.
# Model settings are defined in /dev/models.h

# make sensinode.upload - Will use nano_programmer to upload file using D2xx Devboard
# make sensinode.serialdump - Will use the Contiki serialdump tool on the default UART
# make foo.model - Will copy foo.ihx to foo-XYZ.ihx (e.g. foo-n740.ihx)
PATH:=$(CONTIKI)/platform/$(TARGET)/tools/bin:$(PATH)
export PATH 

ifndef CONTIKI
  $(error CONTIKI not defined! You must specify where CONTIKI resides!)
endif

# Determine our model and (later on) add it as part of the .ihx filename
# Handy when building for various models so we can easily tell which ihx
# is for what model.
# Defaults to N100 (which is what the contiki code does as well)
MODEL_SUFFIX=n100
ifdef DEFINES
	MODEL_SUFFIX=$(patsubst MODEL_N%,n%, \
		$(filter MODEL_%,$(subst $(COMMA), ,$(DEFINES))))
endif

# Define the default UART for tools and tool commands
DEFUART = /dev/ttyUSB0
PROG = $(CONTIKI)/tools/sensinode/nano_programmer/nano_programmer -d $(DEFUART)
SERIALDUMP = $(CONTIKI)/tools/sky/serialdump-linux -b115200 $(DEFUART)

CONTIKI_TARGET_DIRS = . dev
CONTIKI_TARGET_MAIN = $(addprefix $(OBJECTDIR)/,contiki-sensinode-main.rel)

CONTIKI_TARGET_SOURCEFILES = contiki-sensinode-main.c
CONTIKI_TARGET_SOURCEFILES += leds.c leds-arch.c serial-line.c sensors.c
CONTIKI_TARGET_SOURCEFILES += sensinode-sensors.c button-sensor.c adc-sensor.c
CONTIKI_TARGET_SOURCEFILES += n740.c models.c m25p16.c slip-arch.c slip.c
CONTIKI_TARGET_SOURCEFILES += putchar.c debug.c

CONTIKI_SOURCEFILES += $(CONTIKI_TARGET_SOURCEFILES)

CLEAN += *.sensinode

ifeq ($(UIP_CONF_IPV6),1)
  CFLAGS += -DUIP_CONF_IPV6=1
  ifeq ($(OFFSET_FIRMWARE),1)
    CFLAGS += -DDISCO_ENABLED=1
    CONTIKI_TARGET_SOURCEFILES += disco.c
  endif
  CONTIKI_TARGET_SOURCEFILES += viztool.c
  CONTIKI_SOURCEFILES += rpl-of0.c
endif

FORCE:

# .sensinode target so we can behave similar to other targets
# Lastly, it will create a %-$(MODEL).ihx file
%.$(TARGET): %.hex FORCE
	cp $< $(<:.hex=.$(TARGET))
	if [ -f $(<:.hex=.ihx) ] ; then \
	cp $(<:.hex=.ihx) $(<:.hex=-$(MODEL_SUFFIX).ihx); fi
	@echo "\nReport"
	@echo "==============="
	@echo 'Code footprint:'
	@echo    'Area                                Addr        Size' \
	         '         Decimal'
	@echo    '----------------------------------  --------    --------' \
	         '     --------'
	@echo -n 'HOME,CSEG,CONST,XINIT,GS*           $(HOME_START)    '
	@egrep ',CODE\)' $(<:.hex=.map) | egrep -v '(^BANK[1-9][^=])' | uniq | \
	awk '{ SUM += $$5 } END { printf "%08X =    %8d", SUM, SUM }'
	@echo '. bytes (REL,CON,CODE)'
	@egrep '(^BANK[1-9][^=])' $(<:.hex=.map) | uniq | sort
	@egrep -A 5 'Other memory' $(<:.hex=.mem)

%.upload: %.hex
	$(PROG) -P $<

sensinode.serialdump:
	$(SERIALDUMP)

### Define the CPU directory
CONTIKI_CPU=$(CONTIKI)/cpu/cc2430
include $(CONTIKI)/cpu/cc2430/Makefile.cc2430

contiki-$(TARGET).a:# $(addprefix $(OBJECTDIR)/,symbols.rel)