diff --git a/examples/zolertia/zoul/rtcc/test-rtcc.c b/examples/zolertia/zoul/rtcc/test-rtcc.c
index 9b8895c09..48068ca5d 100644
--- a/examples/zolertia/zoul/rtcc/test-rtcc.c
+++ b/examples/zolertia/zoul/rtcc/test-rtcc.c
@@ -159,8 +159,8 @@ PROCESS_THREAD(test_remote_rtcc_process, ev, data)
    * minute.  In case we would want to trigger the alarm on a specific time,
    * then we would want to set a daily repeat interval
    */
-  if(rtcc_set_alarm_time_date(simple_td, RTCC_ALARM_ON,
-                              RTCC_REPEAT_MINUTE) == AB08_ERROR) {
+  if(rtcc_set_alarm_time_date(simple_td, RTCC_ALARM_ON, RTCC_REPEAT_MINUTE,
+                              RTCC_TRIGGER_INT1) == AB08_ERROR) {
     printf("Fail: couldn't set the alarm\n");
     PROCESS_EXIT();
   }
diff --git a/platform/zoul/dev/rtcc-config.h b/platform/zoul/dev/rtcc-config.h
index de39d5ec8..cf5f92135 100644
--- a/platform/zoul/dev/rtcc-config.h
+++ b/platform/zoul/dev/rtcc-config.h
@@ -99,5 +99,4 @@ static const ab080x_register_config_t ab080x_default_setting[] =
 /**
  * @}
  * @}
- */
-
+ */
\ No newline at end of file
diff --git a/platform/zoul/dev/rtcc.c b/platform/zoul/dev/rtcc.c
index e27bdc555..0fe4284f5 100644
--- a/platform/zoul/dev/rtcc.c
+++ b/platform/zoul/dev/rtcc.c
@@ -388,10 +388,17 @@ rtcc_get_time_date(simple_td_map *data)
 }
 /*---------------------------------------------------------------------------*/
 int8_t
-rtcc_set_alarm_time_date(simple_td_map *data, uint8_t state, uint8_t repeat)
+rtcc_set_alarm_time_date(simple_td_map *data, uint8_t state, uint8_t repeat,
+                         uint8_t trigger)
 {
   uint8_t aux[4], buf[RTCC_ALARM_MAP_SIZE];
 
+  if((trigger != RTCC_TRIGGER_INT2) && (trigger != RTCC_TRIGGER_INT1) &&
+     (trigger != RTCC_TRIGGER_BOTH)) {
+    PRINTF("RTC: invalid trigger pin\n");
+    return AB08_ERROR;
+  }
+
   if(state == RTCC_ALARM_OFF) {
     if(ab08_read_reg((INT_MASK_ADDR + CONFIG_MAP_OFFSET),
                      &aux[0], 1) == AB08_ERROR) {
@@ -505,12 +512,25 @@ rtcc_set_alarm_time_date(simple_td_map *data, uint8_t state, uint8_t repeat)
   /* Clear the AIE alarm bit */
   aux[INT_MASK_ADDR] &= ~INTMASK_AIE;
 
-  /* Configure Interrupt parameters for Alarm Interrupt Mode in nIRQ pin,
-   * and fixed level until interrupt flag is cleared
+  /* Configure Interrupt parameters for Alarm Interrupt Mode in nIRQ
+   * or nAIRQ pins and fixed level until interrupt flag is cleared
+   * RTC_INT1 is connected to the CC2538
+   * RTC_INT2 is connected to the power management PIC in revision B
    */
+  if (trigger == RTCC_TRIGGER_INT2) { 
+    aux[CTRL_2_ADDR] |= CTRL2_OUT2S_NAIRQ_OUTB;
+  /* Only options left enable the INT1 interrupt pin */
+  } else {
+    GPIO_ENABLE_INTERRUPT(RTC_INT1_PORT_BASE, RTC_INT1_PIN_MASK);
+    ioc_set_over(RTC_INT1_PORT, RTC_INT1_PIN, IOC_OVERRIDE_PUE);
+    nvic_interrupt_enable(RTC_INT1_VECTOR);
+  }
 
-  /* Enable nIRQ if at least one interrupt is enabled */
-  aux[CTRL_2_ADDR] |= CTRL2_OUT1S_NIRQ_NAIRQ_OUT;
+  if (trigger == RTCC_TRIGGER_INT1) {
+    aux[CTRL_2_ADDR] |= CTRL2_OUT1S_NIRQ_NAIRQ_OUT;
+  } else if (trigger == RTCC_TRIGGER_BOTH) {
+    aux[CTRL_2_ADDR] |= (CTRL2_OUT1S_NIRQ_NAIRQ_OUT + CTRL2_OUT2S_NAIRQ_OUTB);
+  }
 
   if(repeat != RTCC_REPEAT_NONE) {
     aux[INT_MASK_ADDR] &= ~INTMASK_IM_LOW;
@@ -523,11 +543,6 @@ rtcc_set_alarm_time_date(simple_td_map *data, uint8_t state, uint8_t repeat)
     return AB08_ERROR;
   }
 
-  /* Enable interrupts */
-  GPIO_ENABLE_INTERRUPT(RTC_INT1_PORT_BASE, RTC_INT1_PIN_MASK);
-  ioc_set_over(RTC_INT1_PORT, RTC_INT1_PIN, IOC_OVERRIDE_PUE);
-  nvic_interrupt_enable(RTC_INT1_VECTOR);
-
   /* Write to the alarm counters */
   if(ab08_write_reg((HUNDREDTHS_ALARM_ADDR + ALARM_MAP_OFFSET), buf,
                     RTCC_ALARM_MAP_SIZE) == AB08_ERROR) {
diff --git a/platform/zoul/dev/rtcc.h b/platform/zoul/dev/rtcc.h
index 4bbcbfe4f..ba4ac7850 100644
--- a/platform/zoul/dev/rtcc.h
+++ b/platform/zoul/dev/rtcc.h
@@ -275,6 +275,13 @@ enum {
   RTCC_AUTOCAL_17_MIN,
   RTCC_AUTOCAL_9_MIN,
 };
+/* -------------------------------------------------------------------------- */
+enum {
+  RTCC_TRIGGER_INT1 = 0,
+  RTCC_TRIGGER_INT2,
+  RTCC_TRIGGER_BOTH,
+};
+
 /** @} */
 /* -------------------------------------------------------------------------- */
 /** \name Readable Date and time memory map implementation
@@ -337,12 +344,13 @@ int8_t rtcc_print(uint8_t value);
  * \param data date and time values (in decimal) to match against
  * \param state set on/off the alarm interruption
  * \param repeat set the frequency of the alarm (minute, hourly, daily, etc.)
+ * \param trigger interrupt trigger (INT1, INT2 or both)
  * \return
  * \           AB08_SUCCESS date/time set
  * \           AB08_ERROR failed to set time/date (enable DEBUG for more info)
  */
 int8_t rtcc_set_alarm_time_date(simple_td_map *data, uint8_t state,
-                                uint8_t repeat);
+                                uint8_t repeat, uint8_t trigger);
 
 /**
  * \brief Manually calibrate the RTCC
@@ -377,4 +385,4 @@ int8_t rtcc_init(void);
 /**
  * @}
  * @}
- */
+ */
\ No newline at end of file