Commit Graph

9 Commits

Author SHA1 Message Date
Michael LeMay
abeed93da5 x86: Add driver for Intel Quark X1000 built-in Ethernet
This patch adds a simple, space-efficient driver for the Ethernet
interface built into the Intel Quark X1000.  It only allocates a
single packet descriptor for each of the transmit and receive
directions, computes checksums on the CPU, and enables
store-and-forward mode for both transmit and receive directions.
2015-12-21 08:06:14 -02:00
Ricardo de Almeida Gonzaga
60f6edef80 x86: Add support for PCI BAR1
This patch adds support for PCI BAR1 and also changes
the pci_init(), instead of having one function for each `bar`
we now set the `bar` to pci_config_addr_t parameter before calling
the pci_init() function..
2015-12-21 08:06:14 -02:00
Michael LeMay
6dc27579bc x86: Extend PCI driver module with support for metadata and configuration writes
This patch adds the 'meta' field to the generic driver structure to
point to optional driver-defined metadata.  It also modifies the
associated initialization routine to populate it and updates the 16X50
UART driver to use the new initialization routine signature.  This
patch also adds a function to perform PCI configuration register
writes, definitions for the PCI Command configuration register address
and some of the bits in that register, and a function to set
additional bits in that register.  Finally, it adds macros to help
with performing MMIO to and from PCI devices.
2015-12-21 08:06:14 -02:00
Ricardo de Almeida Gonzaga
c796e270bf x86: Add Intel Quark X1000 PCI Interrupt Routing support
PCI Interrupt Routing is mapped using Interrupt Queue Agents
IRQAGENT[0:3] and aggregating the INT[A:D] interrupts for each
PCI-mapped device in the SoC.

PCI based interrupts PIRQ[A:H] are then available for consumption
by either the 8259 PICs or the IO-APIC, depending on the configuration
of the 8 PIRQx Routing Control Registers PIRQ[A:H].

More information about can be find in Intel Quark X1000 datasheet[1]
section 21.11.

[1] - http://www.intel.com/content/www/us/en/embedded/products/quark/quark-x1000-datasheet.html
2015-12-21 08:06:14 -02:00
Michael LeMay
6acdf50262 x86: Add driver for MMIO-accessible 16X50 UART
This patch adds a driver for an MMIO-accessible 16X50 UART.  It
assumes that the boot firmware assigned an MMIO range to the UART.  It
operates in polled mode with FIFOs enabled.
2015-12-21 08:06:14 -02:00
Michael LeMay
c5f9cefac7 x86: Add generic driver structure and associated initialization code
This patch adds a generic device driver structure with a field for
referencing an MMIO range.  It also provides a structure
initialization procedure that initializes the MMIO range field with
the value read from the PCI BAR0 register for a device.
2015-12-21 08:06:14 -02:00
Michael LeMay
2dccb55e15 x86: Add PCI support
This patch adds the pci.c and pci.h files, which support access to PCI
configuration registers through a function interface.  It defines the
PCI configuration register access I/O port addresses and the
pci_config_addr union and structure to assist in specifying addresses
of PCI configuration registers.  It also defines the PCI configuration
register identifier for PCI BAR0.

This patch also adds wrappers for 32-bit 'in' and 'out' port I/O
instructions.  They were placed in helpers.S, since they may be useful
to other modules besides just the PCI support module.
2015-12-21 08:06:14 -02:00
Andre Guedes
cb0510ebcf x86: Disable NMI while initializing RTC
According to [1], we should disable non-maskable and maskable interrupts
while initializing RTC. Otherwise, the RTC may be left in an undefined
state (non-functional) if an interrupt occurs. Currently, maskable
interrupts are already disabled, but NMI is not.

This patch adds helpers APIs to enable/disable non-maskable interrupts
(NMI) and changes rtc_init() to disable NMI while initializing the RTC.

NMI enable/disable code is legacy-PC specific therefore it was put in
driver/legacy_pc/ directory.

Regarding the RTC initialization changes, just calling nmi_disable() and
nmi_enable is not enough since NMI and RTC share the same IO port. So We
should also set the NMI_ENABLE bit while selecting the RTC_INDEX.

Additionally, the nmi_disable() call is not strictly required since we
set the NMI_ENABLE bit while selecting the RTC_INDEX. However, to make
clear hat we are disabling NMI and to improve readability (by matching
NMI disable/enable), the nmi_disable() call was purposely used.

[1] http://wiki.osdev.org/RTC
2015-12-21 08:06:14 -02:00
Jesus Sanchez-Palencia
23e8090257 x86: Move available drivers into drivers/legacy_pc/
All drivers implemented so far are for chips which are only available
on legacy x86 PCs. This commit moves them into a more appropriate folder,
also making the cpu/x86/drivers/ folder ready for other x86 based SoCs.
2015-12-21 08:06:14 -02:00