Commit Graph

1118 Commits

Author SHA1 Message Date
Ian Martin
274b3dcd0b CC2538: Add hardware flow control (RTS/CTS) support on UART1. 2014-06-03 12:38:24 -04:00
George Oikonomou
b864ec2b71 Merge pull request #661 from hexluthor/watchdog-enable
CC2538: Add WATCHDOG_CONF_ENABLE to optionally disable the watchdog timer
2014-05-18 14:11:49 +02:00
George Oikonomou
026864d129 Merge pull request #665 from hexluthor/cc2538-flash-conf
CC2538: Add FLASH_CONF_ORIGIN and FLASH_CONF_SIZE config parameters.
2014-05-18 13:12:49 +02:00
Nicolas Tsiftes
73086e34f7 Merge pull request #632 from nfi/verbosity-control-stm32w
Add support for verbosity control for building STM32W-based platforms
2014-05-07 16:12:12 +02:00
Ian Martin
2abaeaa8cc CC2538: Add FLASH_CONF_ORIGIN and FLASH_CONF_SIZE config parameters. 2014-05-02 11:35:58 -04:00
Ian Martin
7081440eff CC2538: Add WATCHDOG_CONF_ENABLE to optionally disable the watchdog timer. 2014-05-02 10:28:30 -04:00
Oliver Schmidt
5829bc5159 Adjustment to cc65 change. 2014-05-01 21:32:32 +02:00
George Oikonomou
b0f1199202 Merge pull request #636 from g-oikonomou/fix-random-init-lockup
Fix CC2538 random_init lockup
2014-04-18 13:28:40 +01:00
George Oikonomou
49bf7cc241 Merge pull request #616 from hexluthor/listing
CC2538: Add a Makefile rule to generate a final assembly listing.
2014-04-17 22:13:52 +01:00
Benoît Thébaudeau
d93d129da6 cc2538: uart: Make it possible to use several UARTs simultaneously
This avoids the limitation of having a single UART available at runtime, without
duplicating code.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2014-04-17 18:53:44 +02:00
Brad Campbell
af27d2d252 [CC2538-SPI] Implement SPI_FLUSH, spi mode, !CS
Because the CC2538 has a multi-byte SPI RX FIFO, flushing the buffer
requires more than just a single read. This adds a loop that empties the
entire RX buffer on a FLUSH().

Different SPI chips needs different SPI settings. This commit adds a
function that allows chip drivers to configure the SPI peripheral before
using it.

The frame pin the driver was using as a chip select does not work as
most devices expect it to. It toggles after every byte, and most chips
interpret that as end of message. To make drivers more reliable, each
chip driver should setup a GPIO and assert it as needed.
2014-04-15 14:07:10 -04:00
Nicolas Tsiftes
19cd33664d Merge pull request #633 from nfi/verbosity-control-msp430
Add support for verbosity control for building MSP430-based platforms with the IAR compiler.
2014-04-14 16:38:07 +02:00
George Oikonomou
602f834caf Merge pull request #472 from ADVANSEE/cc2538-clock-adjust-etimer-poll
cc2538: clock: Fix clock / timer issues with PM1/2
2014-04-13 16:35:17 +01:00
George Oikonomou
eed1352282 Fix CC2538 random_init lockup
Contiki sometimes fails to boot correctly and locks up in
random_init()

This problem only manifests itself for specific versions
of the arm-gcc toolchain and then again only for specific
levels of optimisation (-Os vs -O2, depending on the
value of the SMALL make variable)

The lockup is caused when we write an RFCORE XREG before
the RF clock ungating has taken effect, which in turn
only occurs depending on the assembly generated for those
two instructions:

  REG(SYS_CTRL_RCGCRFC) = 1;

  REG(RFCORE_XREG_FRMCTRL0) = 0x00000008;

This commit makes the RNG wait for the ungating to take
effect before attempting to write the register
2014-04-13 14:38:00 +01:00
George Oikonomou
33abe26ec8 Merge pull request #411 from ADVANSEE/cc2538-adc
cc2538: Add adc driver and example
2014-04-13 03:05:12 +01:00
George Oikonomou
22554e6d72 Merge pull request #596 from hexluthor/cc2538-uart-baudrate
cc2538: Support any UART baudrate.
2014-04-13 02:51:58 +01:00
Niclas Finne
757950f87f Set the RAM and flash size based on the CPU configuration for STM32W 2014-04-11 17:41:09 +02:00
Niclas Finne
0122373fdc OBJECTDIR is defined by Makefile.include 2014-04-11 17:41:08 +02:00
Niclas Finne
4e7abb09c2 Support verbosity control when building for STM32W-based platforms 2014-04-11 17:41:06 +02:00
Niclas Finne
2c953c3346 Support verbosity control when building MSP430-based platforms with
the IAR compiler.
2014-04-11 17:36:42 +02:00
Nicolas Tsiftes
1b49b68c3b Merge pull request #606 from atiselsts/master
Fix MCU clock calibration in msp430f2xxx based platforms (e.g. Zolertia Z1)
2014-04-09 21:52:08 +02:00
Ian Martin
56d0dfdc7a CC2538: Add a Makefile rule to generate a final assembly listing. 2014-04-02 18:17:49 -04:00
Niclas Finne
279b7fd040 Added rule to autocompile mspsim if needed and show warning if submodule MSPSim has not been initialized 2014-03-28 11:11:51 +01:00
Oliver Schmidt
a630fbd5da Removed unused variable. 2014-03-27 19:24:23 +01:00
Atis Elsts
68b65e6c47 Fix CPU clock calibration in msp430f2xxx based platforms (e.g. Zolertia Z1).
The following problems were present in the existing DCO calibration algorithm:

Problem #1. In function msp430_quick_synch_dco(), the "for(i=0; i < 1000; i++) { .. }" loop is optimized away by the compiler, as i is not volatile. Making i volatile would improve the results, but would not be sufficient: see the next point.

Problem #2. According to MSP430F2617 Device Erratasheet, bug BCL12 precludes a naive implementations of "fast" calibration altogether. The bug is present on all MCU revisions up to date.

The description of the bug:
"After switching RSELx bits (located in register BCSCTL1) from a value of >13 to a value of <12 OR from a value of <12 to a value of >13, the resulting clock delivered by the DCO can stop before the new clock frequency is applied. This dead time is approximately 20 us. In some instances, the DCO may completely stop, requiring a power cycle.

Furthermore, if all of the RSELx bits in the BSCTL1 register are set, modifying the DCOCTL register to change the DCOx or the MODx bits could also result in DCO dead time or DCO hang up."

In Contiki code for msp430f2xxx @ 8MHz, the RSEL search currently typically goes from 15 down to 11, thus violating the rules.

Step-by-step RSEL change is proposed as the best possible workaround:
"[..] more reliable method can be implemented by changing the RSEL bits step by step in order to guarantee safe function without any dead time of the DCO."

Problem #3. The old Contiki code started from the highest possible calibration values: RSEL=15, DCOx=7. According to MSP430F2617
datasheet, this means that the DCO frequency is set to 26 MHz. For one, Vcc under 3V is not supported for this frequency, so this means that battery-powered nodes have a big problem. The minimal operating voltages are:
- 1.8V for RSEL <= 13
- 2.2V for RSEL = 14
- 3.0V for RSEL = 15
So the correct way is to always start calibration from RSEL <= 13, unless explicityly pre-calibred values are present.

Problem #4. Timer B should be turned off after the calibration, following the "Principles for Low-Power Applications" in MSP430 user's Guide.

The patch fixes these issues by performing step-by-step calibration and turning off Timer B afterwards. As opposed to MSP430F1xxx calibration, this algorithm does not change the ACLK divider beforehand; attempts to make calibration more precise would lead to looping in some cases, as the calibration step granularity at larger frequencies is quite big.

Additionally, the patch improves DCOSYNCH_CONF_ENABLED behavior, allowing the resynchronization to correct for more than one step.
2014-03-25 11:47:13 +01:00
Ian Martin
336224633a Eliminate UART_CONF_IBRD and UART_CONF_FBRD. 2014-03-22 10:26:03 -04:00
Ian Martin
ee45fc7533 Change uart_set_baudrate() to a do-while statement. 2014-03-22 10:22:11 -04:00
Ian Martin
1ceb8ae358 Fix rounding error in baudrate calculation. 2014-03-22 10:21:54 -04:00
Oliver Schmidt
370650baa3 Updated cc65 URL. 2014-03-15 16:55:39 +01:00
Ian Martin
e3c19714d4 cc2538: Support any UART baudrate. 2014-03-14 16:06:24 -04:00
George Oikonomou
5675e688a8 Merge pull request #562 from Noolitic/CC2538_UART
CC2538: add support for UART baudrate 9600, 38400 and 57600
2014-03-08 23:41:52 +00:00
Brad Campbell
d14f0d5eed CC2538: add secondary location to ieee address
The CC2538 currently has two addressing options: a hardcoded address set
at compile time or the address stored in primary address section of the
info page. This commit adds the option to choose the secondary location
of the ieee address from the info page, or any memory address.

To use, define `IEEE_ADDR_CONF_USE_SECONDARY_LOCATION` in `project-conf.h`
or similar.

For example:

    #define IEEE_ADDR_CONF_USE_SECONDARY_LOCATION 1
2014-03-06 10:31:30 -05:00
Oliver Schmidt
b6c9950b94 Adjust shadow register to full 8kB RX buffer. 2014-02-27 20:23:41 +01:00
Oliver Schmidt
3e5e054f2a Adjusted base address to final product. 2014-02-26 20:23:09 +01:00
LudovicW
d979e5b096 CC2538: add support for UART baudrate 9600, 38400 and 57600 2014-02-11 16:01:36 +01:00
Oliver Schmidt
9a44bafb16 Merge pull request #553 from oliverschmidt/master
Some fine tuning after the recent general modularization.
2014-02-02 11:14:17 -08:00
Oliver Schmidt
ee3050897a Some fine tuning after the recent general modularization. 2014-02-02 17:59:06 +01:00
Oliver Schmidt
4db675e259 Some fine tuning after the recent general modularization. 2014-02-02 17:47:17 +01:00
Oliver Schmidt
e16521e5c1 Merge pull request #550 from oliverschmidt/master
Avoid compiler warnings.
2014-01-31 16:22:53 -08:00
Oliver Schmidt
a94e7e63e2 Avoid compiler warnings. 2014-02-01 00:46:57 +01:00
George Oikonomou
332d56ac11 Make some CC2538 CFLAGS and LDFLAGS common
Some CFLAGS and LDFLAGS previously only enabled with SMALL=1 have
now been enabled for all builds, regardless of the value of SMALL.

Therefore, from now on, SMALL only chooses between -Os and -O2
2014-01-31 20:02:43 +00:00
George Oikonomou
a63376f8be Use -Os for CC2538 builds
As discussed in #503, -Os was broken with one of the toolchains
recommended in the platform's README and for that reason we were
using -O2 by default.

This commit sets the default to -Os and updates the README to no
longer recommend the toolchain in question
2014-01-31 20:02:43 +00:00
George Oikonomou
c8fbf8ca6e Merge pull request #503 from ADVANSEE/cc2538-nrdata-noload
cc2538: Clean up link stage
2014-01-30 07:58:55 -08:00
Nicolas Tsiftes
4e6bed24f9 Merge pull request #547 from adamdunkels/push/rimeaddr-linkaddr
Rename the rimeaddr module to linkaddr
2014-01-29 12:57:44 -08:00
Adam Dunkels
45265249fc Changed the name of the rimeaddr module to linkaddr 2014-01-29 20:12:24 +01:00
George Oikonomou
345532c559 Merge pull request #546 from ADVANSEE/cc2538-fix-disabled-lpm
cc2538: lpm: Fix build for LPM_CONF_ENABLE == 0
2014-01-29 08:40:56 -08:00
Adam Dunkels
765e9acded Merge pull request #499 from adamdunkels/bold/modularize-everything
A bold move: modularize everything
2014-01-29 08:17:10 -08:00
Benoît Thébaudeau
42c287f363 cc2538: lpm: Fix build for LPM_CONF_ENABLE == 0
lpm.c needs to #include lpm.h in order to get the definition of
lpm_periph_permit_pm1_func_t, which made the replacement macros conflict with
the function definitions for the LPM_CONF_ENABLE == 0 case. This change fixes
this issue by #if-ing out the code in lpm.c in that case. Also, the replacement
macro for lpm_register_peripheral() was missing in that case, which is fixed
here.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2014-01-28 20:21:06 +01:00
Benoît Thébaudeau
a562acb160 cc2538: Fix library linkage
If a project needs to use some libraries at link stage, then the corresponding
linker options (e.g. '-lm') have to be passed after any .o file depending on
these libraries. Hence, LDFLAGS cannot be used to add such options when invoking
$(LD) in Makefile.cc2538, or it should be moved to the correct location.
Instead, this change adds TARGET_LIBFILES to the correct location, like most
other Contiki targets.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2014-01-28 14:32:30 +01:00
Adam Dunkels
824d2047da Add the explicit list of modules, since we cannot do auto-dependency management of them 2014-01-26 23:20:47 +01:00