Commit Graph

214 Commits

Author SHA1 Message Date
Benoît Thébaudeau
4a6e19ed38 cc2538: pwm: Automatically disable PM1+ if running
The peripheral core clocks of the PWM timers are gated in PM1+, so these
power modes must be disabled if a PWM timer is running. Use
lpm_register_peripheral() to handle this automatically and dynamically.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-12-13 02:39:55 +01:00
Benoît Thébaudeau
9c6d9a7fe0 cc2538: pwm: Fix clock
The peripheral core clock of the general-purpose timers used by the PWM
driver is the system clock, not the I/O clock.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-12-13 02:39:39 +01:00
Benoît Thébaudeau
5b1457e4ab cc2538: Fix stack alignment
According to the Procedure Call Standard for the ARM Architecture
(AAPCS) - ABI r2.09 [1], §5.2.1.2, the stack pointer must be
double-word-aligned at a public interface. The stack implementation
being full-descending, this requires that the top of stack be
double-word-aligned too.

[1] http://infocenter.arm.com/help/topic/com.arm.doc.ihi0042e/IHI0042E_aapcs.pdf

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-12-12 22:33:05 +01:00
Benoît Thébaudeau
648b6926b5 Merge pull request #1102 from bthebaudeau/cc2538-build-without-contiki-target-library
cc2538: Build without the Contiki target library
2015-12-05 00:42:31 +01:00
Antonio Lignan
e47b309536 Added note in PWM driver and example about PM0 2015-11-30 09:43:35 +01:00
Antonio Lignan
37fcb927be Added PWM driver for the Zolertia Zoul module and CC2538 platforms 2015-11-25 23:56:29 +01:00
Benoît Thébaudeau
5d98cb71e2 cc2538: Add support for Coffee
Coffee is placed by default at the beginning of the flash memory, right
before the firmware. This avoids the memory gaps that there could be
before and after Coffee if it were placed after the firmware, because it
is unlikely that the end of the firmware is aligned with a flash page
boundary, and the CCA is not flash-page-aligned. Thanks to that, Coffee
is also always in the same flash area if its size remains unchanged,
even if the firmware changes, which makes it possible to keep the Coffee
files when reprogramming the firmware after a partial flash erase
command.

The default configuration of Coffee is set to use sensible values for a
typical usage on this SoC, i.e. for sensor data logging.

The default size of Coffee is set to 0 in order not to waste flash if
Coffee is unused.

COFFEE_CONF_CUSTOM_PORT can be defined to a header file to be used with
"#include" in order to override the default CC2538 port of Coffee. This
makes it possible to use Coffee with an external memory device rather
than with the internal flash memory, without having to alter the Contiki
files.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-11-19 01:22:58 +01:00
Benoît Thébaudeau
ee3ee049e4 cc2538: Set the entry point to the CCA
No entry point was defined, so it defaulted to the beginning of the
.text output section where the vector table is located by default in
Contiki. Actually, the vector table may be located elsewhere, and the
ROM-based boot loader first reads the CCA to find the vector table.

Consequently, this commit sets the entry point to the CCA, which fixes
both the entry point and the initial symbol reference, so this commit
also removes the now-unneeded "__used__" and "KEEP" keywords from the
CCA.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-11-19 01:18:34 +01:00
Benoît Thébaudeau
96dd24836c cc2538: Use &vectors instead of flash/.text start address
The current CC2538 linker script in Contiki places the vector table at
the beginning of the flash memory / .text output section. However, this
location is arbitrary (the only requirement is that the vector table is
512-byte aligned), and custom linker scripts may be used with Contiki,
which means that Contiki may be used with a vector table placed
elsewhere. Thus, using the flash/.text start address in the CCA and as
the default NVIC VTABLE value was wrong.

This commit rather uses the address of the vectors[] array from
startup-gcc.c, which makes it possible to freely move around the vector
table without breaking anything or having to use a custom startup-gcc.c
and to configure the NVIC driver for that. Moreover, referencing the
vectors[] array naturally prevents it and its input section from being
garbage-collected by the linker, so this commit also removes the
now-unneeded "used" and "KEEP" keywords from the vector table.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-11-19 01:18:33 +01:00
Benoît Thébaudeau
a191fcdb84 cc2538: nvic: Simplify VTABLE configuration
The only thing needed for VTABLE is the absolute address of the vector
table. Splitting it between code/SRAM base and offset complicates things
and brings nothing.

Consequently, this commit merges the NVIC VTABLE configurations into a
single one giving the vector table absolute address.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-11-19 01:18:33 +01:00
Benoît Thébaudeau
efb4b858e2 cc2538: Define the flash memory organization
Define the flash memory page and word sizes. These definitions are
grouped with the flash lock bit page and CCA definitions, so flash-cca.h
is renamed to flash.h.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-11-19 01:18:33 +01:00
Benoît Thébaudeau
790c253d6d cc2538: Define and use device features
Define the available CC2538 devices and their features, and use them to
define the linker script memory regions. The .nrdata output section is
now always defined in order to trigger an error if it is used but no
memory is available for it. The CC2538 device used by Contiki is made a
configuration option, the CC2538SF53 device being the default.

This makes more sense than defining the flash memory address and size as
configuration options like previously, all the more not all values are
possible and all the features are linked by each device.

This change also makes it possible to:
 - use the correct SRAM parameters for the CC2538NF11,
 - know at build time if the AES, SHA, ECC and RSA hardware features are
   available on the selected CC2538 device.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-11-19 01:18:33 +01:00
Simon Duquennoy
fbd78a7e3b Merge pull request #1293 from simonduq/pr/fix-warnings
Fix a number of compiler warnings and enable -Werror in Travis
2015-11-10 08:49:11 +01:00
Adam Dunkels
12a185f394 Added the WERROR=1 flag to the CC2538 and CC26xx CPUs 2015-10-20 10:11:23 +02:00
AntiCat
d631270af4 cc2538: Add PKA drivers, ECC algorithms and examples 2015-10-18 20:14:17 +02:00
Atis Elsts
2f79810b58 Use ENERGEST_SWITCH to switch between different power modes to improve energest accuracy. 2015-09-04 11:46:00 +02:00
Antonio Lignan
8cc0a12a9f Merge pull request #1097 from bthebaudeau/cc2538-examples-fix-warnings
cc2538: examples: Fix build warnings
2015-06-24 11:39:24 +02:00
Benoît Thébaudeau
0b1a0d2bd9 Merge pull request #1092 from g-oikonomou/contrib/remote_watchdog_stop
Remove CC2530 and CC2538 dummy watchdog_stop()
2015-06-18 21:56:13 +02:00
Benoît Thébaudeau
afe5d0403d cc2538: Build without the Contiki target library
The GNU linker ld searches and processes libraries and object files in
the order they are specified. Library files are archive files whose
members are object files. The linker handles an archive file by scanning
through it for members that define symbols that have so far been
referenced but not defined. But an ordinary object file is linked in the
usual fashion.

The C library is implicitly linked after all object files and libraries
specified on the command line.

Because of that, if the C library depends on the Contiki target library,
e.g. for the implementation of system calls, then these dependencies are
not linked, which results in undefined references. Actually, the Contiki
target library also needs the C library, hence a circular dependency
between these libraries, which means that explicitly adding -lc anywhere
on the command line can not help. The only solution in that case is to
pass these libraries to ld between --start-group and --end-group.
Archives grouped in this way are searched repeatedly by the linker until
no new undefined references are created.

This archive grouping option has a significant performance cost for the
linking stage. Moreover, having to use it and to pass -lc explicitly on
the command line is unusual, which is disturbing and more complicated
for users needing the C library to depend on the Contiki target library.
The same would be true for circular dependencies between the Contiki
target library and any other library.

Another issue with the Contiki target library is that it may alter the
apparent behavior of the weak vs. strong symbols, because of the way ld
handles archives, which may make it discard archive object files
containing strong versions of referenced symbols:
 - If a symbol has a weak and a strong version in this library, both
   inside the same object file, then the linker uses the strong
   definition.
 - If a weak symbol in this library has a strong counterpart in an
   object file outside, then the linker uses the strong definition.
 - If a strong symbol in this library is inside an object file
   containing other referenced symbols, and has a weak counterpart
   anywhere, then the linker uses the strong definition.
 - If a strong symbol in this library is the only symbol referenced in
   its object file, and has a weak counterpart in an object file
   outside, then the linker uses the strong definition if this library
   is linked first, and the weak one otherwise.
 - If a strong symbol in this library is the only symbol referenced in
   its object file, and has a weak counterpart in another object file in
   this library, then the linker uses the definition from the first of
   these objects added when creating this archive.
 - If a symbol has a weak and a strong version, one in this library, and
   the other in another library, then the rules are the same as if both
   were in the Contiki target library.

The existence of cases where the linker uses a weak symbol despite the
presence of its strong counterpart in the sources compiled then passed
to the linker is very error-prone, all the more this behavior depends on
the order the object and archive files are passed on the command lines,
which may just result from the order of source files in lists where it
apparently does not matter. Such cases would be needed in the future,
e.g. to define weak default implementations of some system calls that
can be overridden by platform-specific implementations, both ending up
in the Contiki target library. There was already such a case used to
define the UART and USB ISRs as weak aliases of default_handler(),
relying on this implicit unusual behavior to keep default_handler() if
the UART or USB driver was unused, which was dangerous.

Since the Contiki target library was only used as an intermediate file
during the build, the current commit fixes these issues by simply
directly using the object files instead of building an intermediate
archive from them.

The CONTIKI_OBJECTFILES make variable would be incomplete if it were
used as a simple prerequisite in the %.elf rule in Makefile.cc2538,
because other object files are added to it after this rule. That's why
.SECONDEXPANSION is used to defer its expansion. Another solution would
have been to split Makefile.cc2538, with the variable assignments kept
in it, and the rule definitions moved to Makefile.customrules-cc2538,
but this would have required to add Makefile.customrules-<target> files
to all CC2538 platforms, only to include Makefile.customrules-cc2538.
The solution used here is much simpler.

Because the UART and USB ISRs were weak aliases of default_handler(),
this change would imply that these ISRs would always be used by the
linker instead of default_handler(), even if their drivers were
configured as unused with UART_CONF_ENABLE and USB_SERIAL_CONF_ENABLE,
which would be wrong. This commit fixes this issue by removing these
weak aliases and putting either these ISRs or default_handler() in the
vector table, depending on the configuration. Weak aliases are elegant,
but Contiki's build system does not currently allow to automatically
build or not source files depending on the configuration, so keeping
these weak aliases would have required to add #if constructs somewhere
in the source code, which would have broken their elegance and made them
pointless.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-06-05 21:55:51 +02:00
Benoît Thébaudeau
0f137e4bdd cc2538: uart: Make uart_isr() static
This function is only supposed to be used by uart.c, so it should be
static.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-06-05 21:50:49 +02:00
Benoît Thébaudeau
e8a268cd15 cc2538: aes: Add support for 192- and 256-bit keys
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-06-02 21:41:56 +02:00
Benoît Thébaudeau
801315e819 cc2538: aes: Make it possible to have several keys stored at once
Several keys can be kept at the same time in the key store, and several
keys can be loaded at once. Give access to these features.

The ccm-test example is also improved to better demonstrate the use of
the key store.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-06-02 21:41:07 +02:00
Benoît Thébaudeau
b92a5afcc4 cc2538: ccm: Make it possible to use the interrupt
Using the AES interrupt allows the user process not to waste time
polling for the completion of the operation. This time can be used by
the user process to do something else, or to let the system enter PM0.

Since the system is now free to perform various operations during a
crypto operation, a protection of the crypto resource is added, and PM1+
is prohibited in order not to stall crypto operations.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-06-02 21:41:07 +02:00
Benoît Thébaudeau
117dc4e5e3 cc2538: Add crypto drivers and examples for AES-CCM and SHA-256
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-06-02 21:41:06 +02:00
Benoît Thébaudeau
66acf74612 cc2538: examples: Fix build warnings
Toolchain used:
arm-none-eabi-gcc (GNU Tools for ARM Embedded Processors) 4.9.3 20150303
(release) [ARM/embedded-4_9-branch revision 221220]

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-06-02 01:38:11 +02:00
George Oikonomou
d28eb023ef Remove CC2530 and CC2538 dummy watchdog_stop()
The CC2538 the WDT cannot be stopped once it has been started.
The CC2530/1 WDT can be stopped if it is running in timer mode,
but it cannot be stopped once it has been started in watchdog mode.

Both platforms currently provide "dummy" implementations of `watchdog_stop()`,
one does nothing and the other one basically re-maps `_stop()` to
`_periodic()`.

This was originally done in order to provide implementations for all prototypes
declared in `core/dev/watchdog.h`. In hindsight and as per the discussion
in #1088, this is bad practice since, if the build succeeds, the caller will
expect that the WDT has in fact been stopped, when in reality it has not.

Since the feature (stopping the WDT) is unsupported by the hardware, this pull
removes those dummy implementations. Thus, we will now be able to reliably
detect - at build time - attempts at using this unsupported feature.
2015-06-01 15:24:14 +01:00
Benoît Thébaudeau
1cd3c9e7e5 cc2538: Initialize .data/.bss using ROM functions
This is safer because the previous code assumed that the start and end
VMAs of .data and .bss were word-aligned, which is not always the case,
so the initialization code could write data outside these sections. The
ROM functions support any address boundary.

This is faster because the ROM functions are ultra optimized, using
realignment and the LDM/STM instructions, which is much better than the
previous simple loops of single word accesses.

This is smaller because the ROM functions don't require to add any code
to the target device other than simple function calls.

This makes the code simpler and more maintainable because standard
functions are not reimplemented and no assembly is used.

Note that this is also faster and smaller than the corresponding
functions from the standard string library.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-05-23 18:50:52 +02:00
Benoît Thébaudeau
609c615303 cc2538: Move the stack out of .bss
The initialization code clearing .bss is allowed to use the stack, so
the stack can not be in .bss, or this code will badly fail if it uses
the stack.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-05-23 18:50:52 +02:00
Benoît Thébaudeau
0de729572b cc2538: Word-align .data LMA
In order to be fast, the reset_handler() function uses word accesses to
initialize the .data output section. However, most toolchains do not
automatically force the alignment of an output section LMA to use the
maximum alignment of all its input sections. Because of that, assuming
that .data contains some words, the LMA of the .data output section was
not word-aligned in some cases, resulting in an initialization performed
using slow unaligned word accesses.

This commit forces the alignment of the LMA of the .data output section
with a word boundary in order to always use fast aligned word accesses
to read the .data load area.

Note that this solution is better than using ALIGN_WITH_INPUT, both
because the latter is a new feature incompatible with older toolchains,
and because it could create a big gap between _etext and the LMA of
.data if strongly-aligned data were added to .data, although only a word
alignment is required here.

The same considerations apply to the VMA of .data. However, it is
already automatically word-aligned, both because .data contains words,
and because the end VMA of the previous output section (.socdata) is
word-aligned. Moreover, if the VMA of .data were forcibly word-aligned,
then a filled gap could appear at the beginning of this section if
strongly-aligned data were added to it, thus wasting flash memory.
Consequently, it's better not to change anything for the VMA of .data,
all the more it's very unlikely that it does not contain any word and
that the end VMA of .socdata becomes non-word-aligned, and this would
only result in a slower initialization.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-05-23 18:12:54 +02:00
Benoît Thébaudeau
0d260f61a0 cc2538: Fix .data LMA/VMA mismatch with some toolchains
Some toolchains, like Sourcery CodeBench Lite 2013.05-23 arm-none-eabi
(http://sourcery.mentor.com/public/gnu_toolchain/arm-none-eabi/)
automatically force the alignment of an output section LMA to use the
maximum alignment of all its input sections. This toolchain uses GNU
binutils 2.23, and this automatic behavior is the same as the manual
behavior of the ALIGN_WITH_INPUT feature of GNU binutils 2.24+.

This behavior is not an issue per se, but it creates a gap between
_etext and the LMA of the .data output section if _etext does not have
the same alignment, while reset_handler() initialized this section by
copying the data from _etext to its VMA, hence an offset in the
addresses of loaded data, and missing data.

This commit fixes this issue by making reset_handler() directly use the
LMA of the .data section using LOADADDR(.data), rather than assuming
that _etext is this LMA.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-05-23 18:12:53 +02:00
Ulf Knoblich
d8efa8428c cc2538: Allow for configuration of processor speed 2015-05-19 18:55:55 +02:00
Ulf Knoblich
a388a1bcd7 CC2538: added support for SSI1 2015-05-18 10:02:55 +02:00
Benoît Thébaudeau
25532e8abf Merge pull request #754 from wwhuang/master
[CC2538] Fix SPI_FLUSH
2015-05-16 20:55:30 +02:00
Benoît Thébaudeau
d64927397f Merge pull request #968 from g-oikonomou/cc2538-contrib-on-chip-sensors
Move CC2538 VDD/3 and On-Chip Temp sensors to the CPU dir
2015-05-14 19:21:56 +02:00
Benoît Thébaudeau
71f22b1775 Merge pull request #966 from g-oikonomou/cc2538-startup-to-cpu-dir
Move cc2538 startup-gcc.c to the CPU dir
2015-05-14 18:43:39 +02:00
George Oikonomou
f7baf5aba2 Change CC2538 USB and UART handlers to weak 2015-05-13 01:31:26 +01:00
George Oikonomou
96e1647270 Move cc2538 startup-gcc.c to the CPU dir 2015-05-13 01:31:10 +01:00
George Oikonomou
3717522680 Re-work the CC2538 driver to be a driver for the Srf06 ALS only 2015-05-12 23:42:19 +01:00
George Oikonomou
06b0ee4a8b Include CC2538 sensors in the build 2015-05-12 23:42:19 +01:00
George Oikonomou
9cc800d728 Add CC2538 VDD sensor driver 2015-05-12 23:42:19 +01:00
George Oikonomou
f474514ee5 Add CC2538 tmp sensor driver 2015-05-12 23:42:19 +01:00
George Oikonomou
40716ab515 Add generic header for CC2538 sensors 2015-05-12 23:42:18 +01:00
George Oikonomou
a2d6df225e Merge pull request #967 from g-oikonomou/cc2538-contrib-rf-local-vars
Use local variable to store RF on/off state
2015-05-09 22:23:31 +01:00
George Oikonomou
2059be3a43 Merge pull request #1031 from bthebaudeau/cc2538-gpio-irqs
cc2538: gpio: Improve and fix IRQ management
2015-05-03 18:42:53 +01:00
Ulf Knoblich
8e624c750d cc2538 i2c bug in clock computation 2015-04-29 11:07:59 +02:00
Benoît Thébaudeau
3d9d52de87 cc2538: gpio: Fix missed interrupts
Only the interrupt flags that have been handled must be cleared.
Otherwise, if a new interrupt occurs after the interrupt statuses are
read and before they are cleared, then it is discarded without having
been handled. This issue was particularly likely with two interrupt
trigger conditions occurring on different pins of the same port in a
short period of time.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-04-27 01:14:51 +02:00
Benoît Thébaudeau
1a5632cba0 cc2538: gpio: Fix missed power-up interrupts
Power-up interrupts do not always update the regular interrupt status.
Because of that, in order not to miss power-up interrupts, the ISR must
handle both the regular and the power-up interrupt statuses.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-04-27 01:14:51 +02:00
Benoît Thébaudeau
1e67ab3941 cc2538: gpio: Add macros to get interrupt status
Introduce new useful GPIO macros to:
 - get the raw interrupt status of a port,
 - get the masked interrupt status of a port,
 - get the power-up interrupt status of a port.

These macros are cleaner and less error-prone than raw register access
code copied all over the place.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-04-27 01:14:51 +02:00
Benoît Thébaudeau
41d9078ed4 cc2538: gpio: Factor out duplicated ISR code
This makes the code easier to maintain, and this reduces the binary
image size.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-04-27 01:14:50 +02:00
George Oikonomou
48e987baac Merge pull request #1005 from alignan/i2c_cc2538
CC2538 I2C driver
2015-03-28 23:23:06 +00:00
Benoît Thébaudeau
19fd7a3551 Use additive offsets
OR-ing an offset to a base address instead of adding it is dangerous
because it can only work if the base address is aligned enough for the
offset.

Moreover, if the base address or the offset has a value unknown at
compile time, then the assembly instructions dedicated to 'base +
offset' addressing on most CPUs can't be emitted by the compiler because
this would require the alignment of the base address against the offset
to be known in order to optimize 'base | offset' into 'base + offset'.
In that case, the compiler has to emit more instructions in order to
compute 'base | offset' on most CPUs, e.g. on ARM, which means larger
binary size and slower execution.

Hence, replace all occurrences of 'base | offset' with 'base + offset'.
This must become a coding rule.

Here are the results for the cc2538-demo example:
 - Compilation of uart_init():
    * before:
        REG(regs->base | UART_CC) = 0;
        200b78:	f446 637c 	orr.w	r3, r6, #4032	; 0xfc0
        200b7c:	f043 0308 	orr.w	r3, r3, #8
        200b80:	2200      	movs	r2, #0
        200b82:	601a      	str	r2, [r3, #0]

    * now:
        REG(regs->base + UART_CC) = 0;
        200b7a:	2300      	movs	r3, #0
        200b7c:	f8c4 3fc8 	str.w	r3, [r4, #4040]	; 0xfc8

 - Size of the .text section:
    * before:	0x4c7c
    * now:	0x4c28
    * saved:	84 bytes

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
2015-03-28 17:28:15 +01:00
William Huang
1e39c9a454 fixed SPI_FLUSH. current implementation waits for rx buffer to fill first. Thus, if we call SPI_FLUSH to make sure the rx fifo is empty when the rx fifo is already empty, we enter an infinite loop 2015-03-26 14:17:06 -04:00
Antonio Lignan
22be9fd8b7 I2C driver taken from PR #677, uncrustified, made functions static and added burst modes 2015-03-25 16:44:12 +01:00
George Oikonomou
5288725af7 Use local variable to store RF on/off state
Fixes #823
2015-02-18 09:05:02 +01:00
George Oikonomou
6bd8bb05f6 Improve wording 2015-02-16 10:17:58 +01:00
George Oikonomou
72914369e8 Re-structure CC2538 doxygen module hierarchy 2015-02-16 10:17:58 +01:00
George Oikonomou
8751e55c94 Improve wording, fix warnigs in the SSI/SPI docs 2015-02-16 10:17:58 +01:00
George Oikonomou
a93a8912c2 Clarify GPIO read and write macros 2015-02-16 10:17:57 +01:00
George Oikonomou
4100cbc9c0 Fix doxygen warning in the CC2538 uDMA driver's header 2015-02-16 10:17:57 +01:00
George Oikonomou
88e190103c Fix doxygen warning in the CC2538 SPI driver 2015-02-16 10:17:57 +01:00
George Oikonomou
b6bd556805 Fix clock.h warnings caused by multiple, conflicting documentation blocks of clock functions 2015-02-15 21:48:30 +01:00
Michael Karlsson
62fc6f2f07 corrected code style error 2015-02-13 13:46:57 +01:00
Michael Karlsson
be9879cf18 fixed error in saving status 2015-01-21 22:35:30 +01:00
Michael Karlsson
37def294ce fixed bug that made radio die after error when not using default channel and/or not using a RDC protocol 2015-01-21 22:28:31 +01:00
Jelmer Tiete
b088326b5e Corrected the register offset value of ANA_REGS_IVCTRL. TI was using the address offset instead of the physical address in their header file. 2014-12-19 04:14:34 -05:00
George Oikonomou
9d7c3b9866 Improve documentation for the CC2538 IEEE address re-ordering 2014-06-06 18:33:28 +01:00
George Oikonomou
5acc20fc47 Improve code style 2014-06-06 18:32:58 +01:00
George Oikonomou
623d6084e7 Make the CC2538 secondary IEEE address location configurable 2014-06-06 18:15:07 +01:00
LudovicW
66edb5b263 Fix incorrect IEEE address byte re-ordering 2014-06-06 17:22:33 +01:00
George Oikonomou
2e166a83c7 Merge pull request #691 from hexluthor/rts-cts
CC2538: Add hardware flow control (RTS/CTS) support on UART1.
2014-06-04 09:22:58 +01:00
George Oikonomou
ba9c2d40eb Merge pull request #682 from g-oikonomou/watchdog-cc2538
Confine CC2538 WDT on/off conf inside the driver
2014-06-03 22:05:08 +01:00
Adam Dunkels
64f65b4e45 Merge pull request #617 from nfi/extended-radio-api
Extended radio API with support for setting channel, pan id, addressing modes, etc
2014-06-03 21:32:53 +02:00
Ian Martin
274b3dcd0b CC2538: Add hardware flow control (RTS/CTS) support on UART1. 2014-06-03 12:38:24 -04:00
George Oikonomou
807ee624e4 Confine CC2538 WDT on/off conf inside the driver
Instead of requiring all calls to `watchdog_start` to be
wrapped inside `#if WATCHDOG_CONF_ENABLE` guards, we control
things from within the WDT driver itself.

This commit also includes some minor documentation and
indentation cleanups
2014-05-18 14:12:16 +02:00
George Oikonomou
b864ec2b71 Merge pull request #661 from hexluthor/watchdog-enable
CC2538: Add WATCHDOG_CONF_ENABLE to optionally disable the watchdog timer
2014-05-18 14:11:49 +02:00
Ian Martin
2abaeaa8cc CC2538: Add FLASH_CONF_ORIGIN and FLASH_CONF_SIZE config parameters. 2014-05-02 11:35:58 -04:00
Ian Martin
7081440eff CC2538: Add WATCHDOG_CONF_ENABLE to optionally disable the watchdog timer. 2014-05-02 10:28:30 -04:00
George Oikonomou
08c884afa0 Improve the CC2538 extended RF API implementation
* Decouple 64-bit address from LINKADDR_SIZE
* get and set object from/to the start/end of the src/dest buffer
* We expect size == 8 (rather than size < 8) for both get_ and set_object. Error otherwise
* The RF no longer sets parameters by itself. We let the platform do this, using the extended API.
2014-04-23 12:20:16 +01:00
George Oikonomou
6028c0765f Don't hardcode min and max TX power values 2014-04-23 12:16:50 +01:00
George Oikonomou
b0f1199202 Merge pull request #636 from g-oikonomou/fix-random-init-lockup
Fix CC2538 random_init lockup
2014-04-18 13:28:40 +01:00
George Oikonomou
49bf7cc241 Merge pull request #616 from hexluthor/listing
CC2538: Add a Makefile rule to generate a final assembly listing.
2014-04-17 22:13:52 +01:00
Benoît Thébaudeau
d93d129da6 cc2538: uart: Make it possible to use several UARTs simultaneously
This avoids the limitation of having a single UART available at runtime, without
duplicating code.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2014-04-17 18:53:44 +02:00
Brad Campbell
af27d2d252 [CC2538-SPI] Implement SPI_FLUSH, spi mode, !CS
Because the CC2538 has a multi-byte SPI RX FIFO, flushing the buffer
requires more than just a single read. This adds a loop that empties the
entire RX buffer on a FLUSH().

Different SPI chips needs different SPI settings. This commit adds a
function that allows chip drivers to configure the SPI peripheral before
using it.

The frame pin the driver was using as a chip select does not work as
most devices expect it to. It toggles after every byte, and most chips
interpret that as end of message. To make drivers more reliable, each
chip driver should setup a GPIO and assert it as needed.
2014-04-15 14:07:10 -04:00
George Oikonomou
0ec1eda75e Implement extended RF API for the CC2538 2014-04-14 15:25:30 +02:00
George Oikonomou
602f834caf Merge pull request #472 from ADVANSEE/cc2538-clock-adjust-etimer-poll
cc2538: clock: Fix clock / timer issues with PM1/2
2014-04-13 16:35:17 +01:00
George Oikonomou
eed1352282 Fix CC2538 random_init lockup
Contiki sometimes fails to boot correctly and locks up in
random_init()

This problem only manifests itself for specific versions
of the arm-gcc toolchain and then again only for specific
levels of optimisation (-Os vs -O2, depending on the
value of the SMALL make variable)

The lockup is caused when we write an RFCORE XREG before
the RF clock ungating has taken effect, which in turn
only occurs depending on the assembly generated for those
two instructions:

  REG(SYS_CTRL_RCGCRFC) = 1;

  REG(RFCORE_XREG_FRMCTRL0) = 0x00000008;

This commit makes the RNG wait for the ungating to take
effect before attempting to write the register
2014-04-13 14:38:00 +01:00
George Oikonomou
33abe26ec8 Merge pull request #411 from ADVANSEE/cc2538-adc
cc2538: Add adc driver and example
2014-04-13 03:05:12 +01:00
Niclas Finne
a98e153e23 Added stub for extended radio API for cc2538 2014-04-03 13:38:23 +02:00
Ian Martin
56d0dfdc7a CC2538: Add a Makefile rule to generate a final assembly listing. 2014-04-02 18:17:49 -04:00
Ian Martin
336224633a Eliminate UART_CONF_IBRD and UART_CONF_FBRD. 2014-03-22 10:26:03 -04:00
Ian Martin
ee45fc7533 Change uart_set_baudrate() to a do-while statement. 2014-03-22 10:22:11 -04:00
Ian Martin
1ceb8ae358 Fix rounding error in baudrate calculation. 2014-03-22 10:21:54 -04:00
Ian Martin
e3c19714d4 cc2538: Support any UART baudrate. 2014-03-14 16:06:24 -04:00
George Oikonomou
5675e688a8 Merge pull request #562 from Noolitic/CC2538_UART
CC2538: add support for UART baudrate 9600, 38400 and 57600
2014-03-08 23:41:52 +00:00
Brad Campbell
d14f0d5eed CC2538: add secondary location to ieee address
The CC2538 currently has two addressing options: a hardcoded address set
at compile time or the address stored in primary address section of the
info page. This commit adds the option to choose the secondary location
of the ieee address from the info page, or any memory address.

To use, define `IEEE_ADDR_CONF_USE_SECONDARY_LOCATION` in `project-conf.h`
or similar.

For example:

    #define IEEE_ADDR_CONF_USE_SECONDARY_LOCATION 1
2014-03-06 10:31:30 -05:00
LudovicW
d979e5b096 CC2538: add support for UART baudrate 9600, 38400 and 57600 2014-02-11 16:01:36 +01:00
George Oikonomou
332d56ac11 Make some CC2538 CFLAGS and LDFLAGS common
Some CFLAGS and LDFLAGS previously only enabled with SMALL=1 have
now been enabled for all builds, regardless of the value of SMALL.

Therefore, from now on, SMALL only chooses between -Os and -O2
2014-01-31 20:02:43 +00:00
George Oikonomou
a63376f8be Use -Os for CC2538 builds
As discussed in #503, -Os was broken with one of the toolchains
recommended in the platform's README and for that reason we were
using -O2 by default.

This commit sets the default to -Os and updates the README to no
longer recommend the toolchain in question
2014-01-31 20:02:43 +00:00
George Oikonomou
c8fbf8ca6e Merge pull request #503 from ADVANSEE/cc2538-nrdata-noload
cc2538: Clean up link stage
2014-01-30 07:58:55 -08:00
Nicolas Tsiftes
4e6bed24f9 Merge pull request #547 from adamdunkels/push/rimeaddr-linkaddr
Rename the rimeaddr module to linkaddr
2014-01-29 12:57:44 -08:00