mirror of
https://github.com/oliverschmidt/contiki.git
synced 2024-12-21 19:29:18 +00:00
127 lines
5.1 KiB
Plaintext
127 lines
5.1 KiB
Plaintext
/**
|
|
\addtogroup rf230mac
|
|
@{
|
|
*/
|
|
|
|
/**
|
|
* \defgroup macdoc SICSLoWMAC Implementation
|
|
* @{
|
|
|
|
\section macintro 1. Introduction
|
|
|
|
The phase1 MAC implemented to support the IPv6/6LoWPAN stack within the Contiki
|
|
project is a light weight yet adequate beginning. This phase supports point to
|
|
point data connectivity between a router device and an end device. The router is
|
|
the RZ USB stick from the ATAVRRZRAVEN kit. The end node is the AVR
|
|
Raven from the ATAVRRZRAVEN kit. The picture below shows the complete ATAVRRZRAVEN kit.
|
|
|
|
\image html raven.png
|
|
|
|
The next phases will implement a commissioning concept including scan, and
|
|
beacon generation. These kinds of primitives will allow dynamic network
|
|
formation. Additionally, routing and low power/sleep will be implemented in
|
|
following phases.
|
|
|
|
\section macprereqs 2. Prerequisites
|
|
|
|
See the \ref tutorialraven for required systems setup configuration.
|
|
|
|
\section macoverview 3. MAC Overview
|
|
|
|
This MAC follows the recommendations of RFC4944 with respect to data frames and
|
|
acknowledgements (i.e. all data frames are acknowledged). At the time of this
|
|
writing (phase 1) beacons (frames) and association events are not implemented.
|
|
Additionally, data frames always carry both source and destination addresses.
|
|
PANID compression (intra-pan) is not used so both source and destination PANID's
|
|
are present in the frame.
|
|
|
|
The SICSLoWMAC supports the IEEE 802.15.4 Data Request primitive and the Data
|
|
Request Indication primitive. The data request primitive constructs a <b>proper</b>
|
|
802.15.4 frame for transmission over the air while the data indication parses a
|
|
received frame for processing in higher layers (6LoWPAN). The source code for
|
|
the mac can be found in the sicslowmac.[c,h] files.
|
|
|
|
To assemble a frame a MAC header is constructed with certain presumptions:
|
|
-# Long source and destination addresses are used.
|
|
-# A hard coded PANID is used.
|
|
-# A hard coded channel is used.
|
|
-# Acknowledgements are used.
|
|
-# Up to 3 auto retry attempts are used.
|
|
|
|
These and other variables are defined in mac.h.
|
|
|
|
Given this data and the output of the 6LoWPAN function, the MAC can construct
|
|
the data frame and the Frame Control Field for transmission.
|
|
|
|
An IEEE 802.15.4 MAC data frame consists of the fields shown below:
|
|
|
|
\image html dataframe.png
|
|
|
|
The Frame Control Field (FCF) consist of the fields shown below:
|
|
|
|
\image html fcf.jpg
|
|
|
|
\note The MAC address of each node is expected to be stored in EEPROM and
|
|
retrieved during the initialization process immediately after power on.
|
|
|
|
\section macrelationship 4. 6LoWPAN, MAC and Radio Relationship
|
|
|
|
The output function of the 6LoWPAN layer (sicslowpan.c) is the input function
|
|
to the MAC (sicslowmac.c). The output function of the MAC is the input function
|
|
of the radio (radio.c). When the radio receives a frame over the air it processes
|
|
it in its TRX_END event function. If the frame passes address and CRC filtering
|
|
it is queued in the MAC event queue. Subsequently, when the MAC task is processed,
|
|
the received frame is parsed and handed off to the 6LoWPAN layer via its input
|
|
function. These relationships are depicted below:
|
|
|
|
\image html layers.png
|
|
|
|
\section maccode 5. Source Code Location
|
|
|
|
The source code for the MAC, Radio and support functions is located in the path:
|
|
- \\cpu\\avr\\radio
|
|
- \\rf230
|
|
- \\mac
|
|
- \\ieee-manager
|
|
|
|
-# The \\rf230 folder contains the low level HAL drivers to access and control
|
|
the radio as well as the low level frame formatting and parsing functions.
|
|
-# The \\mac folder contains the MAC layer code, the generic MAC initialization
|
|
functions and the defines mentioned in section 3.
|
|
-# The \\ieee-manager folder contains the access functions for various PIB
|
|
variables and radio functions such as channel setting.
|
|
|
|
The source code for the Raven platforms is located in the path:
|
|
- \\platform
|
|
- \\avr-raven
|
|
- \\avr-ravenlcd
|
|
- \\avr-ravenusb
|
|
-# The \\avr-raven folder contains the source code to initialize and start the
|
|
raven board.
|
|
-# The \\avr-ravenlcd folder contains the complete source code to initialize
|
|
and start the ATmega3209P on raven board in a user interface capacity. See the
|
|
Doxygen generated documentation for more information.
|
|
-# The \\avr-ravenusb folder contains the source code to initialize and start
|
|
the raven USB stick as a network interface on either Linux or Windows platforms.
|
|
Note that appropriate drivers are located in the path:
|
|
- \\cpu\\avr\\dev\\usb\\INF
|
|
|
|
\section macavrstudio 6. AVR Studio Project Location
|
|
|
|
There are two projects that utilize the Logo Certified IPv6 and 6LoWPAN layers
|
|
contributed to the Contiki project by Cisco. These are ping-ipv6and webserver-ipv6
|
|
applications. They are located in the following paths:
|
|
- \\examples\\webserver-ipv6
|
|
and
|
|
- \\examples\\ping-ipv6
|
|
|
|
The ping-ipv6 application will allow the USB stick to ping the Raven board while
|
|
the webserver-ipv6 application will allow the raven board to serve a web page.
|
|
When the ravenlcd-3290 application is programmed into the ATmega3290P on the
|
|
Raven board, the Raven board can ping the USB stick and it can periodically update
|
|
the temperature in the appropriate web page when served.
|
|
|
|
|
|
*/
|
|
/** @} */
|
|
/** @} */ |