mirror of
https://github.com/oliverschmidt/contiki.git
synced 2024-11-08 23:08:29 +00:00
6dc27579bc
This patch adds the 'meta' field to the generic driver structure to point to optional driver-defined metadata. It also modifies the associated initialization routine to populate it and updates the 16X50 UART driver to use the new initialization routine signature. This patch also adds a function to perform PCI configuration register writes, definitions for the PCI Command configuration register address and some of the bits in that register, and a function to set additional bits in that register. Finally, it adds macros to help with performing MMIO to and from PCI devices.
124 lines
4.6 KiB
C
124 lines
4.6 KiB
C
/*
|
|
* Copyright (C) 2015, Intel Corporation. All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
#include "uart-16x50.h"
|
|
#include <stdlib.h>
|
|
#include "helpers.h"
|
|
|
|
/* Refer to Intel Quark SoC X1000 Datasheet, Chapter 18 for more details on
|
|
* UART operation.
|
|
*/
|
|
|
|
/* Divisor Latch Access Bit (DLAB) mask for Line Control Register (LCR).
|
|
*
|
|
* When bit is set, enables access to divisor registers to set baud rate. When
|
|
* clear, enables access to other registers mapped to the same addresses as the
|
|
* divisor registers.
|
|
*/
|
|
#define UART_LCR_7_DLAB BIT(7)
|
|
/* Setting for LCR that configures the UART to operate with no parity, 1 stop
|
|
* bit, and eight bits per character.
|
|
*/
|
|
#define UART_LCR_8BITS 0x03
|
|
|
|
/* FIFO Control Register (FCR) bitmasks */
|
|
#define UART_FCR_0_FIFOE BIT(0) /*< enable FIFOs */
|
|
#define UART_FCR_1_RFIFOR BIT(1) /*< reset RX FIFO */
|
|
#define UART_FCR_2_XFIFOR BIT(2) /*< reset TX FIFO */
|
|
|
|
/* Line Status Register (LSR) Transmit Holding Register Empty bitmask to check
|
|
* whether the Transmit Holding Register (THR) or TX FIFO is empty.
|
|
*/
|
|
#define UART_LSR_5_THRE BIT(5)
|
|
|
|
/* MMIO registers for UART */
|
|
typedef struct uart_16x50_regs {
|
|
volatile uint32_t rbr_thr_dll, ier_dlh, iir_fcr, lcr;
|
|
volatile uint32_t mcr, lsr, msr, scr, usr, htx, dmasa;
|
|
} uart_16x50_regs_t;
|
|
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \brief Initialize an MMIO-programmable 16X50 UART.
|
|
* \param c_this Structure that will be initialized to represent the device.
|
|
* \param pci_addr PCI address of device.
|
|
* \param dl Divisor setting to configure the baud rate.
|
|
*/
|
|
void
|
|
uart_16x50_init(uart_16x50_driver_t *c_this,
|
|
pci_config_addr_t pci_addr,
|
|
uint16_t dl)
|
|
{
|
|
/* This assumes that the UART had an MMIO range assigned to it by the
|
|
* firmware during boot.
|
|
*/
|
|
pci_init_bar0(c_this, pci_addr, 0);
|
|
|
|
uart_16x50_regs_t *regs = (uart_16x50_regs_t *)c_this->mmio;
|
|
|
|
/* Set the DLAB bit to enable access to divisor settings. */
|
|
regs->lcr = UART_LCR_7_DLAB;
|
|
|
|
/* The divisor settings configure the baud rate, and may need to be defined
|
|
* on a per-device basis.
|
|
*/
|
|
regs->rbr_thr_dll = dl & UINT8_MAX;
|
|
regs->ier_dlh = dl >> 8;
|
|
|
|
/* Clear the DLAB bit to enable access to other settings and configure other
|
|
* UART parameters.
|
|
*/
|
|
regs->lcr = UART_LCR_8BITS;
|
|
|
|
/* Enable the FIFOs. */
|
|
regs->iir_fcr = UART_FCR_0_FIFOE | UART_FCR_1_RFIFOR | UART_FCR_2_XFIFOR;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \brief Transmit a character through a UART.
|
|
* \param c_this Initialized structure representing the device.
|
|
* \param c Character to be transmitted.
|
|
*
|
|
* This procedure will block indefinitely until the UART is ready
|
|
* to accept the character to be transmitted.
|
|
*/
|
|
void
|
|
uart_16x50_tx(uart_16x50_driver_t c_this, uint8_t c)
|
|
{
|
|
struct uart_16x50_regs *regs = (uart_16x50_regs_t *)c_this.mmio;
|
|
|
|
/* Wait for space in TX FIFO. */
|
|
while((regs->lsr & UART_LSR_5_THRE) == 0);
|
|
|
|
/* Add character to TX FIFO. */
|
|
regs->rbr_thr_dll = c;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|