contiki/cpu/cc2538/dev/pka.h

872 lines
52 KiB
C

/*
* Original file:
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
* All rights reserved.
*
* Port to Contiki:
* Copyright (c) 2014 Andreas Dröscher <contiki@anticat.ch>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* 3. Neither the name of the copyright holder nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
* OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/**
* \addtogroup cc2538
* @{
*
* \defgroup cc2538-pka cc2538 PKA engine
*
* Driver for the cc2538 PKA engine
* @{
*
* \file
* Header file for the cc2538 PKA engine driver
*/
#ifndef PKA_H_
#define PKA_H_
#include "contiki.h"
#include <stdint.h>
/*---------------------------------------------------------------------------*/
/** \name PKA memory
* @{
*/
#define PKA_RAM_BASE 0x44006000 /**< PKA Memory Address */
#define PKA_RAM_SIZE 0x800 /**< PKA Memory Size */
#define PKA_MAX_CURVE_SIZE 12 /**< Define for the maximum curve
size supported by the PKA module
in 32 bit word. */
#define PKA_MAX_LEN 12 /**< Define for the maximum length of
the big number supported by the
PKA module in 32 bit word. */
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA register offsets
* @{
*/
#define PKA_APTR 0x44004000 /**< PKA vector A address During
execution of basic PKCP
operations, this register is
double buffered and can be
written with a new value for the
next operation; when not
written, the value remains
intact. During the execution of
sequencer-controlled complex
operations, this register may
not be written and its value is
undefined at the conclusion of
the operation. The driver
software cannot rely on the
written value to remain intact. */
#define PKA_BPTR 0x44004004 /**< PKA vector B address During
execution of basic PKCP
operations, this register is
double buffered and can be
written with a new value for the
next operation; when not
written, the value remains
intact. During the execution of
sequencer-controlled complex
operations, this register may
not be written and its value is
undefined at the conclusion of
the operation. The driver
software cannot rely on the
written value to remain intact. */
#define PKA_CPTR 0x44004008 /**< PKA vector C address During
execution of basic PKCP
operations, this register is
double buffered and can be
written with a new value for the
next operation; when not
written, the value remains
intact. During the execution of
sequencer-controlled complex
operations, this register may
not be written and its value is
undefined at the conclusion of
the operation. The driver
software cannot rely on the
written value to remain intact. */
#define PKA_DPTR 0x4400400C /**< PKA vector D address During
execution of basic PKCP
operations, this register is
double buffered and can be
written with a new value for the
next operation; when not
written, the value remains
intact. During the execution of
sequencer-controlled complex
operations, this register may
not be written and its value is
undefined at the conclusion of
the operation. The driver
software cannot rely on the
written value to remain intact. */
#define PKA_ALENGTH 0x44004010 /**< PKA vector A length During
execution of basic PKCP
operations, this register is
double buffered and can be
written with a new value for the
next operation; when not
written, the value remains
intact. During the execution of
sequencer-controlled complex
operations, this register may
not be written and its value is
undefined at the conclusion of
the operation. The driver
software cannot rely on the
written value to remain intact. */
#define PKA_BLENGTH 0x44004014 /**< PKA vector B length During
execution of basic PKCP
operations, this register is
double buffered and can be
written with a new value for the
next operation; when not
written, the value remains
intact. During the execution of
sequencer-controlled complex
operations, this register may
not be written and its value is
undefined at the conclusion of
the operation. The driver
software cannot rely on the
written value to remain intact. */
#define PKA_SHIFT 0x44004018 /**< PKA bit shift value For basic
PKCP operations, modifying the
contents of this register is
made impossible while the
operation is being performed.
For the ExpMod-variable and
ExpMod-CRT operations, this
register is used to indicate the
number of odd powers to use
(directly as a value in the
range 1-16). For the ModInv and
ECC operations, this register is
used to hold a completion code. */
#define PKA_FUNCTION 0x4400401C /**< PKA function This register
contains the control bits to
start basic PKCP as well as
complex sequencer operations.
The run bit can be used to poll
for the completion of the
operation. Modifying bits [11:0]
is made impossible during the
execution of a basic PKCP
operation. During the execution
of sequencer-controlled complex
operations, this register is
modified; the run and stall
result bits are set to zero at
the conclusion, but other bits
are undefined. Attention:
Continuously reading this
register to poll the run bit is
not allowed when executing
complex sequencer operations
(the sequencer cannot access the
PKCP when this is done). Leave
at least one sysclk cycle
between poll operations. */
#define PKA_COMPARE 0x44004020 /**< PKA compare result This
register provides the result of
a basic PKCP compare operation.
It is updated when the run bit
in the PKA_FUNCTION register is
reset at the end of that
operation. Status after a
complex sequencer operation is
unknown */
#define PKA_MSW 0x44004024 /**< PKA most-significant-word of
result vector This register
indicates the (word) address in
the PKA RAM where the most
significant nonzero 32-bit word
of the result is stored. Should
be ignored for modulo
operations. For basic PKCP
operations, this register is
updated when the run bit in the
PKA_FUNCTION register is reset
at the end of the operation. For
the complex-sequencer controlled
operations, updating of the
final value matching the actual
result is done near the end of
the operation; note that the
result is only meaningful if no
errors were detected and that
for ECC operations, the PKA_MSW
register will provide
information for the x-coordinate
of the result point only. */
#define PKA_DIVMSW 0x44004028 /**< PKA most-significant-word of
divide remainder This register
indicates the (32-bit word)
address in the PKA RAM where the
most significant nonzero 32-bit
word of the remainder result for
the basic divide and modulo
operations is stored. Bits [4:0]
are loaded with the bit number
of the most-significant nonzero
bit in the most-significant
nonzero word when MS one control
bit is set. For divide, modulo,
and MS one reporting, this
register is updated when the RUN
bit in the PKA_FUNCTION register
is reset at the end of the
operation. For the complex
sequencer controlled operations,
updating of bits [4:0] of this
register with the
most-significant bit location of
the actual result is done near
the end of the operation. The
result is meaningful only if no
errors were detected and that
for ECC operations; the
PKA_DIVMSW register provides
information for the x-coordinate
of the result point only. */
#define PKA_SEQ_CTRL 0x440040C8 /**< PKA sequencer control and
status register The sequencer is
interfaced with the outside
world through a single control
and status register. With the
exception of bit [31], the
actual use of bits in the
separate sub-fields of this
register is determined by the
sequencer firmware. This
register need only be accessed
when the sequencer program is
stored in RAM. The reset value
of the RESTE bit depends upon
the option chosen for sequencer
program storage. */
#define PKA_OPTIONS 0x440040F4 /**< PKA hardware options register
This register provides the host
with a means to determine the
hardware configuration
implemented in this PKA engine,
focused on options that have an
effect on software interacting
with the module. Note: (32 x
(1st LNME nr. of PEs + 1st LNME
FIFO RAM depth - 10)) equals the
maximum modulus vector length
(in bits) that can be handled by
the modular exponentiation and
ECC operations executed on a PKA
engine that includes an LNME. */
#define PKA_SW_REV 0x440040F8 /**< PKA firmware revision and
capabilities register This
register allows the host access
to the internal firmware
revision number of the PKA
Engine for software driver
matching and diagnostic
purposes. This register also
contains a field that encodes
the capabilities of the embedded
firmware. The PKA_SW_REV
register is written by the
firmware within a few clock
cycles after starting up that
firmware. The hardware reset
value is zero, indicating that
the information has not been
written yet. */
#define PKA_REVISION 0x440040FC /**< PKA hardware revision register
This register allows the host
access to the hardware revision
number of the PKA engine for
software driver matching and
diagnostic purposes. It is
always located at the highest
address in the access space of
the module and contains an
encoding of the EIP number (with
its complement as signature) for
recognition of the hardware
module. */
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_APTR register registers bit fields
* @{
*/
#define PKA_APTR_APTR_M 0x000007FF /**< This register specifies the
location of vector A within the
PKA RAM. Vectors are identified
through the location of their
least-significant 32-bit word.
Note that bit [0] must be zero
to ensure that the vector starts
at an 8-byte boundary. */
#define PKA_APTR_APTR_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_BPTR register registers bit fields
* @{
*/
#define PKA_BPTR_BPTR_M 0x000007FF /**< This register specifies the
location of vector B within the
PKA RAM. Vectors are identified
through the location of their
least-significant 32-bit word.
Note that bit [0] must be zero
to ensure that the vector starts
at an 8-byte boundary. */
#define PKA_BPTR_BPTR_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_CPTR register registers bit fields
* @{
*/
#define PKA_CPTR_CPTR_M 0x000007FF /**< This register specifies the
location of vector C within the
PKA RAM. Vectors are identified
through the location of their
least-significant 32-bit word.
Note that bit [0] must be zero
to ensure that the vector starts
at an 8-byte boundary. */
#define PKA_CPTR_CPTR_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_DPTR register registers bit fields
* @{
*/
#define PKA_DPTR_DPTR_M 0x000007FF /**< This register specifies the
location of vector D within the
PKA RAM. Vectors are identified
through the location of their
least-significant 32-bit word.
Note that bit [0] must be zero
to ensure that the vector starts
at an 8-byte boundary. */
#define PKA_DPTR_DPTR_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_ALENGTH register registers bit fields
* @{
*/
#define PKA_ALENGTH_ALENGTH_M 0x000001FF /**< This register specifies the
length (in 32-bit words) of
Vector A. */
#define PKA_ALENGTH_ALENGTH_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_BLENGTH register registers bit fields
* @{
*/
#define PKA_BLENGTH_BLENGTH_M 0x000001FF /**< This register specifies the
length (in 32-bit words) of
Vector B. */
#define PKA_BLENGTH_BLENGTH_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_SHIFT register registers bit fields
* @{
*/
#define PKA_SHIFT_NUM_BITS_TO_SHIFT_M \
0x0000001F /**< This register specifies the
number of bits to shift the
input vector (in the range 0-31)
during a Rshift or Lshift
operation. */
#define PKA_SHIFT_NUM_BITS_TO_SHIFT_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_FUNCTION register registers bit fields
* @{
*/
#define PKA_FUNCTION_STALL_RESULT \
0x01000000 /**< When written with a 1b,
updating of the PKA_COMPARE,
PKA_MSW and PKA_DIVMSW
registers, as well as resetting
the run bit is stalled beyond
the point that a running
operation is actually finished.
Use this to allow software
enough time to read results from
a previous operation when the
newly started operation is known
to take only a short amount of
time. If a result is waiting,
the result registers is updated
and the run bit is reset in the
clock cycle following writing
the stall result bit back to 0b.
The Stall result function may
only be used for basic PKCP
operations. */
#define PKA_FUNCTION_STALL_RESULT_M \
0x01000000
#define PKA_FUNCTION_STALL_RESULT_S 24
#define PKA_FUNCTION_RUN 0x00008000 /**< The host sets this bit to
instruct the PKA module to begin
processing the basic PKCP or
complex sequencer operation.
This bit is reset low
automatically when the operation
is complete. The complement of
this bit is output as
interrupts[1]. After a reset,
the run bit is always set to 1b.
Depending on the option, program
ROM or program RAM, the
following applies: Program ROM -
The first sequencer instruction
sets the bit to 0b. This is done
immediately after the hardware
reset is released. Program RAM -
The sequencer must set the bit
to 0b. As a valid firmware may
not have been loaded, the
sequencer is held in software
reset after the hardware reset
is released (the reset bit in
PKA_SEQ_CRTL is set to 1b).
After the FW image is loaded and
the Reset bit is cleared, the
sequencer starts to execute the
FW. The first instruction clears
the run bit. In both cases a few
clock cycles are needed before
the first instruction is
executed and the run bit state
has been propagated. */
#define PKA_FUNCTION_RUN_M 0x00008000
#define PKA_FUNCTION_RUN_S 15
#define PKA_FUNCTION_SEQUENCER_OPERATIONS_M \
0x00007000 /**< These bits select the complex
sequencer operation to perform:
000b: None 001b: ExpMod-CRT
010b: ExpMod-ACT4 (compatible
with EIP2315) 011b: ECC-ADD (if
available in firmware, otherwise
reserved) 100b: ExpMod-ACT2
(compatible with EIP2316) 101b:
ECC-MUL (if available in
firmware, otherwise reserved)
110b: ExpMod-variable 111b:
ModInv (if available in
firmware, otherwise reserved)
The encoding of these operations
is determined by sequencer
firmware. */
#define PKA_FUNCTION_SEQUENCER_OPERATIONS_S 12
#define PKA_FUNCTION_COPY 0x00000800 /**< Perform copy operation */
#define PKA_FUNCTION_COPY_M 0x00000800
#define PKA_FUNCTION_COPY_S 11
#define PKA_FUNCTION_COMPARE 0x00000400 /**< Perform compare operation */
#define PKA_FUNCTION_COMPARE_M 0x00000400
#define PKA_FUNCTION_COMPARE_S 10
#define PKA_FUNCTION_MODULO 0x00000200 /**< Perform modulo operation */
#define PKA_FUNCTION_MODULO_M 0x00000200
#define PKA_FUNCTION_MODULO_S 9
#define PKA_FUNCTION_DIVIDE 0x00000100 /**< Perform divide operation */
#define PKA_FUNCTION_DIVIDE_M 0x00000100
#define PKA_FUNCTION_DIVIDE_S 8
#define PKA_FUNCTION_LSHIFT 0x00000080 /**< Perform left shift operation */
#define PKA_FUNCTION_LSHIFT_M 0x00000080
#define PKA_FUNCTION_LSHIFT_S 7
#define PKA_FUNCTION_RSHIFT 0x00000040 /**< Perform right shift operation */
#define PKA_FUNCTION_RSHIFT_M 0x00000040
#define PKA_FUNCTION_RSHIFT_S 6
#define PKA_FUNCTION_SUBTRACT 0x00000020 /**< Perform subtract operation */
#define PKA_FUNCTION_SUBTRACT_M 0x00000020
#define PKA_FUNCTION_SUBTRACT_S 5
#define PKA_FUNCTION_ADD 0x00000010 /**< Perform add operation */
#define PKA_FUNCTION_ADD_M 0x00000010
#define PKA_FUNCTION_ADD_S 4
#define PKA_FUNCTION_MS_ONE 0x00000008 /**< Loads the location of the Most
Significant one bit within the
result word indicated in the
PKA_MSW register into bits [4:0]
of the PKA_DIVMSW register - can
only be used with basic PKCP
operations, except for Divide,
Modulo and Compare. */
#define PKA_FUNCTION_MS_ONE_M 0x00000008
#define PKA_FUNCTION_MS_ONE_S 3
#define PKA_FUNCTION_ADDSUB 0x00000002 /**< Perform combined add/subtract
operation */
#define PKA_FUNCTION_ADDSUB_M 0x00000002
#define PKA_FUNCTION_ADDSUB_S 1
#define PKA_FUNCTION_MULTIPLY 0x00000001 /**< Perform multiply operation */
#define PKA_FUNCTION_MULTIPLY_M 0x00000001
#define PKA_FUNCTION_MULTIPLY_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_COMPARE register registers bit fields
* @{
*/
#define PKA_COMPARE_A_GREATER_THAN_B \
0x00000004 /**< Vector_A is greater than
Vector_B */
#define PKA_COMPARE_A_GREATER_THAN_B_M \
0x00000004
#define PKA_COMPARE_A_GREATER_THAN_B_S 2
#define PKA_COMPARE_A_LESS_THAN_B \
0x00000002 /**< Vector_A is less than Vector_B */
#define PKA_COMPARE_A_LESS_THAN_B_M \
0x00000002
#define PKA_COMPARE_A_LESS_THAN_B_S 1
#define PKA_COMPARE_A_EQUALS_B 0x00000001 /**< Vector_A is equal to Vector_B */
#define PKA_COMPARE_A_EQUALS_B_M \
0x00000001
#define PKA_COMPARE_A_EQUALS_B_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_MSW register registers bit fields
* @{
*/
#define PKA_MSW_RESULT_IS_ZERO 0x00008000 /**< The result vector is all
zeroes, ignore the address
returned in bits [10:0] */
#define PKA_MSW_RESULT_IS_ZERO_M \
0x00008000
#define PKA_MSW_RESULT_IS_ZERO_S 15
#define PKA_MSW_MSW_ADDRESS_M 0x000007FF /**< Address of the most-significant
nonzero 32-bit word of the
result vector in PKA RAM */
#define PKA_MSW_MSW_ADDRESS_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_DIVMSW register registers bit fields
* @{
*/
#define PKA_DIVMSW_RESULT_IS_ZERO \
0x00008000 /**< The result vector is all
zeroes, ignore the address
returned in bits [10:0] */
#define PKA_DIVMSW_RESULT_IS_ZERO_M \
0x00008000
#define PKA_DIVMSW_RESULT_IS_ZERO_S 15
#define PKA_DIVMSW_MSW_ADDRESS_M \
0x000007FF /**< Address of the most significant
nonzero 32-bit word of the
remainder result vector in PKA
RAM */
#define PKA_DIVMSW_MSW_ADDRESS_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_SEQ_CTRL register registers bit fields
* @{
*/
#define PKA_SEQ_CTRL_RESET 0x80000000 /**< Option program ROM: Reset value
= 0. Read/Write, reset value 0b
(ZERO). Writing 1b resets the
sequencer, write to 0b to
restart operations again. As the
reset value is 0b, the sequencer
will automatically start
operations executing from
program ROM. This bit should
always be written with zero and
ignored when reading this
register. Option Program RAM:
Reset value =1. Read/Write,
reset value 1b (ONE). When 1b,
the sequencer is held in a reset
state and the PKA_PROGRAM area
is accessible for loading the
sequencer program (while the
PKA_DATA_RAM is inaccessible),
write to 0b to (re)start
sequencer operations and disable
PKA_PROGRAM area accessibility
(also enables the PKA_DATA_RAM
accesses). Resetting the
sequencer (in order to load
other firmware) should only be
done when the PKA Engine is not
performing any operations (i.e.
the run bit in the PKA_FUNCTION
register should be zero). */
#define PKA_SEQ_CTRL_RESET_M 0x80000000
#define PKA_SEQ_CTRL_RESET_S 31
#define PKA_SEQ_CTRL_SEQUENCER_STATUS_M \
0x0000FF00 /**< These read-only bits can be
used by the sequencer to
communicate status to the
outside world. Bit [8] is also
used as sequencer interrupt,
with the complement of this bit
ORed into the run bit in
PKA_FUNCTION. This field should
always be written with zeroes
and ignored when reading this
register. */
#define PKA_SEQ_CTRL_SEQUENCER_STATUS_S 8
#define PKA_SEQ_CTRL_SW_CONTROL_STATUS_M \
0x000000FF /**< These bits can be used by
software to trigger sequencer
operations. External logic can
set these bits by writing 1b,
cannot reset them by writing 0b.
The sequencer can reset these
bits by writing 0b, cannot set
them by writing 1b. Setting the
run bit in PKA_FUNCTION together
with a nonzero sequencer
operations field automatically
sets bit [0] here. This field
should always be written with
zeroes and ignored when reading
this register. */
#define PKA_SEQ_CTRL_SW_CONTROL_STATUS_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_OPTIONS register registers bit fields
* @{
*/
#define PKA_OPTIONS_FIRST_LNME_FIFO_DEPTH_M \
0xFF000000 /**< Number of words in the first
LNME's FIFO RAM Should be
ignored if LNME configuration is
0. The contents of this field
indicate the actual depth as
selected by the LNME FIFO RAM
size strap input, fifo_size_sel.
Note: Reset value is undefined */
#define PKA_OPTIONS_FIRST_LNME_FIFO_DEPTH_S 24
#define PKA_OPTIONS_FIRST_LNME_NR_OF_PES_M \
0x003F0000 /**< Number of processing elements
in the pipeline of the first
LNME Should be ignored if LNME
configuration is 0. Note: Reset
value is undefined. */
#define PKA_OPTIONS_FIRST_LNME_NR_OF_PES_S 16
#define PKA_OPTIONS_MMM3A 0x00001000 /**< Reserved for a future
functional extension to the LNME
Always 0b */
#define PKA_OPTIONS_MMM3A_M 0x00001000
#define PKA_OPTIONS_MMM3A_S 12
#define PKA_OPTIONS_INT_MASKING 0x00000800 /**< Value 0b indicates that the
main interrupt output (bit [1]
of the interrupts output bus) is
the direct complement of the run
bit in the PKA_CONTROL register,
value 1b indicates that
interrupt masking logic is
present for this output. Note:
Reset value is undefined */
#define PKA_OPTIONS_INT_MASKING_M \
0x00000800
#define PKA_OPTIONS_INT_MASKING_S 11
#define PKA_OPTIONS_PROTECTION_OPTION_M \
0x00000700 /**< Value 0 indicates no additional
protection against side channel
attacks, value 1 indicates the
SCAP option, value 3 indicates
the PROT option; other values
are reserved. Note: Reset value
is undefined */
#define PKA_OPTIONS_PROTECTION_OPTION_S 8
#define PKA_OPTIONS_PROGRAM_RAM 0x00000080 /**< Value 1b indicates sequencer
program storage in RAM, value 0b
in ROM. Note: Reset value is
undefined */
#define PKA_OPTIONS_PROGRAM_RAM_M \
0x00000080
#define PKA_OPTIONS_PROGRAM_RAM_S 7
#define PKA_OPTIONS_SEQUENCER_CONFIGURATION_M \
0x00000060 /**< Value 1 indicates a standard
sequencer; other values are
reserved. */
#define PKA_OPTIONS_SEQUENCER_CONFIGURATION_S 5
#define PKA_OPTIONS_LNME_CONFIGURATION_M \
0x0000001C /**< Value 0 indicates NO LNME,
value 1 indicates one standard
LNME (with alpha = 32, beta =
8); other values reserved. Note:
Reset value is undefined */
#define PKA_OPTIONS_LNME_CONFIGURATION_S 2
#define PKA_OPTIONS_PKCP_CONFIGURATION_M \
0x00000003 /**< Value 1 indicates a PKCP with a
16x16 multiplier, value 2
indicates a PKCP with a 32x32
multiplier, other values
reserved. Note: Reset value is
undefined. */
#define PKA_OPTIONS_PKCP_CONFIGURATION_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_SW_REV register registers bit fields
* @{
*/
#define PKA_SW_REV_FW_CAPABILITIES_M \
0xF0000000 /**< 4-bit binary encoding for the
functionality implemented in the
firmware. Value 0 indicates
basic ModExp with/without CRT.
Value 1 adds Modular Inversion,
value 2 adds Modular Inversion
and ECC operations. Values 3-15
are reserved. */
#define PKA_SW_REV_FW_CAPABILITIES_S 28
#define PKA_SW_REV_MAJOR_FW_REVISION_M \
0x0F000000 /**< 4-bit binary encoding of the
major firmware revision number */
#define PKA_SW_REV_MAJOR_FW_REVISION_S 24
#define PKA_SW_REV_MINOR_FW_REVISION_M \
0x00F00000 /**< 4-bit binary encoding of the
minor firmware revision number */
#define PKA_SW_REV_MINOR_FW_REVISION_S 20
#define PKA_SW_REV_FW_PATCH_LEVEL_M \
0x000F0000 /**< 4-bit binary encoding of the
firmware patch level, initial
release will carry value zero
Patches are used to remove bugs
without changing the
functionality or interface of a
module. */
#define PKA_SW_REV_FW_PATCH_LEVEL_S 16
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA_REVISION register registers bit fields
* @{
*/
#define PKA_REVISION_MAJOR_HW_REVISION_M \
0x0F000000 /**< 4-bit binary encoding of the
major hardware revision number */
#define PKA_REVISION_MAJOR_HW_REVISION_S 24
#define PKA_REVISION_MINOR_HW_REVISION_M \
0x00F00000 /**< 4-bit binary encoding of the
minor hardware revision number */
#define PKA_REVISION_MINOR_HW_REVISION_S 20
#define PKA_REVISION_HW_PATCH_LEVEL_M \
0x000F0000 /**< 4-bit binary encoding of the
hardware patch level, initial
release will carry value zero
Patches are used to remove bugs
without changing the
functionality or interface of a
module. */
#define PKA_REVISION_HW_PATCH_LEVEL_S 16
#define PKA_REVISION_COMPLEMENT_OF_BASIC_EIP_NUMBER_M \
0x0000FF00 /**< Bit-by-bit logic complement of
bits [7:0], EIP-28 gives 0xE3 */
#define PKA_REVISION_COMPLEMENT_OF_BASIC_EIP_NUMBER_S 8
#define PKA_REVISION_BASIC_EIP_NUMBER_M \
0x000000FF /**< 8-bit binary encoding of the
EIP number, EIP-28 gives 0x1C */
#define PKA_REVISION_BASIC_EIP_NUMBER_S 0
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA driver return codes
* @{
*/
#define PKA_STATUS_SUCCESS 0 /**< Success */
#define PKA_STATUS_FAILURE 1 /**< Failure */
#define PKA_STATUS_INVALID_PARAM 2 /**< Invalid parameter */
#define PKA_STATUS_BUF_UNDERFLOW 3 /**< Buffer underflow */
#define PKA_STATUS_RESULT_0 4 /**< Result is all zeros */
#define PKA_STATUS_A_GR_B 5 /**< Big number compare return status if
the first big num is greater than
the second. */
#define PKA_STATUS_A_LT_B 6 /**< Big number compare return status if
the first big num is less than the
second. */
#define PKA_STATUS_OPERATION_INPRG 7 /**< PKA operation is in progress. */
#define PKA_STATUS_OPERATION_NOT_INPRG 8 /**< No PKA operation is in progress. */
#define PKA_STATUS_SIGNATURE_INVALID 9 /**< Signature is invalid. */
/** @} */
/*---------------------------------------------------------------------------*/
/** \name PKA functions
* @{
*/
/** \brief Enables and resets the PKA engine
*/
void pka_init(void);
/** \brief Enables the PKA engine
*/
void pka_enable(void);
/** \brief Disables the PKA engine
* \note Call this function to save power when the engine is unused.
*/
void pka_disable(void);
/** \brief Checks the status of the PKA engine operation
* \retval false Result not yet available, and no error occurred
* \retval true Result available, or error occurred
*/
uint8_t pka_check_status(void);
/** \brief Registers a process to be notified of the completion of a PKA
* operation
* \param p Process to be polled upon IRQ
* \note This function is only supposed to be called by the PKA drivers.
*/
void pka_register_process_notification(struct process *p);
/** @} */
#endif /* PKA_H_ */
/**
* @}
* @}
*/