mirror of
https://github.com/oliverschmidt/contiki.git
synced 2024-12-23 01:29:33 +00:00
237 lines
7.5 KiB
C
237 lines
7.5 KiB
C
/*
|
|
* Copyright (c) 2012, Texas Instruments Incorporated - http://www.ti.com/
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
/**
|
|
* \addtogroup cc2538dk
|
|
* @{
|
|
*
|
|
* \defgroup cc2538-smartrf SmartRF06EB Peripherals
|
|
*
|
|
* Defines related to the SmartRF06EB
|
|
*
|
|
* This file provides connectivity information on LEDs, Buttons, UART and
|
|
* other SmartRF peripherals
|
|
*
|
|
* Notably, PC0 is used to drive LED1 as well as the USB D+ pullup. Therefore
|
|
* when USB is enabled, LED1 can not be driven by firmware.
|
|
*
|
|
* This file can be used as the basis to configure other platforms using the
|
|
* cc2538 SoC.
|
|
* @{
|
|
*
|
|
* \file
|
|
* Header file with definitions related to the I/O connections on the TI
|
|
* SmartRF06EB
|
|
*
|
|
* \note Do not include this file directly. It gets included by contiki-conf
|
|
* after all relevant directives have been set.
|
|
*/
|
|
#ifndef BOARD_H_
|
|
#define BOARD_H_
|
|
|
|
#include "dev/gpio.h"
|
|
#include "dev/nvic.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name SmartRF LED configuration
|
|
*
|
|
* LEDs on the SmartRF06 (EB and BB) are connected as follows:
|
|
* - LED1 (Red) -> PC0
|
|
* - LED2 (Yellow) -> PC1
|
|
* - LED3 (Green) -> PC2
|
|
* - LED4 (Orange) -> PC3
|
|
*
|
|
* LED1 shares the same pin with the USB pullup
|
|
* @{
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
/* Some files include leds.h before us, so we need to get rid of defaults in
|
|
* leds.h before we provide correct definitions */
|
|
#undef LEDS_GREEN
|
|
#undef LEDS_YELLOW
|
|
#undef LEDS_RED
|
|
#undef LEDS_CONF_ALL
|
|
|
|
#define LEDS_YELLOW 2 /**< LED2 (Yellow) -> PC1 */
|
|
#define LEDS_GREEN 4 /**< LED3 (Green) -> PC2 */
|
|
#define LEDS_ORANGE 8 /**< LED4 (Orange) -> PC3 */
|
|
|
|
#if USB_SERIAL_CONF_ENABLE
|
|
#define LEDS_CONF_ALL 14
|
|
#define LEDS_RED LEDS_ORANGE
|
|
#else
|
|
#define LEDS_CONF_ALL 15
|
|
#define LEDS_RED 1 /**< LED1 (Red) -> PC0 */
|
|
#endif
|
|
|
|
/* Notify various examples that we have LEDs */
|
|
#define PLATFORM_HAS_LEDS 1
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name USB configuration
|
|
*
|
|
* The USB pullup is driven by PC0 and is shared with LED1
|
|
*/
|
|
#define USB_PULLUP_PORT GPIO_C_NUM
|
|
#define USB_PULLUP_PIN 0
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name UART configuration
|
|
*
|
|
* On the SmartRF06EB, the UART (XDS back channel) is connected to the
|
|
* following ports/pins
|
|
* - RX: PA0
|
|
* - TX: PA1
|
|
* - CTS: PB0 (Can only be used with UART1)
|
|
* - RTS: PD3 (Can only be used with UART1)
|
|
*
|
|
* We configure the port to use UART0. To use UART1, replace UART0_* with
|
|
* UART1_* below.
|
|
* @{
|
|
*/
|
|
#define UART0_RX_PORT GPIO_A_NUM
|
|
#define UART0_RX_PIN 0
|
|
|
|
#define UART0_TX_PORT GPIO_A_NUM
|
|
#define UART0_TX_PIN 1
|
|
|
|
#define UART1_CTS_PORT GPIO_B_NUM
|
|
#define UART1_CTS_PIN 0
|
|
|
|
#define UART1_RTS_PORT GPIO_D_NUM
|
|
#define UART1_RTS_PIN 3
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name SmartRF Button configuration
|
|
*
|
|
* Buttons on the SmartRF06 are connected as follows:
|
|
* - BUTTON_SELECT -> PA3
|
|
* - BUTTON_LEFT -> PC4
|
|
* - BUTTON_RIGHT -> PC5
|
|
* - BUTTON_UP -> PC6
|
|
* - BUTTON_DOWN -> PC7
|
|
* @{
|
|
*/
|
|
/** BUTTON_SELECT -> PA3 */
|
|
#define BUTTON_SELECT_PORT GPIO_A_NUM
|
|
#define BUTTON_SELECT_PIN 3
|
|
#define BUTTON_SELECT_VECTOR NVIC_INT_GPIO_PORT_A
|
|
|
|
/** BUTTON_LEFT -> PC4 */
|
|
#define BUTTON_LEFT_PORT GPIO_C_NUM
|
|
#define BUTTON_LEFT_PIN 4
|
|
#define BUTTON_LEFT_VECTOR NVIC_INT_GPIO_PORT_C
|
|
|
|
/** BUTTON_RIGHT -> PC5 */
|
|
#define BUTTON_RIGHT_PORT GPIO_C_NUM
|
|
#define BUTTON_RIGHT_PIN 5
|
|
#define BUTTON_RIGHT_VECTOR NVIC_INT_GPIO_PORT_C
|
|
|
|
/** BUTTON_UP -> PC6 */
|
|
#define BUTTON_UP_PORT GPIO_C_NUM
|
|
#define BUTTON_UP_PIN 6
|
|
#define BUTTON_UP_VECTOR NVIC_INT_GPIO_PORT_C
|
|
|
|
/** BUTTON_DOWN -> PC7 */
|
|
#define BUTTON_DOWN_PORT GPIO_C_NUM
|
|
#define BUTTON_DOWN_PIN 7
|
|
#define BUTTON_DOWN_VECTOR NVIC_INT_GPIO_PORT_C
|
|
|
|
/* Notify various examples that we have Buttons */
|
|
#define PLATFORM_HAS_BUTTON 1
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name ADC configuration
|
|
*
|
|
* These values configure which CC2538 pins and ADC channels to use for the ADC
|
|
* inputs.
|
|
*
|
|
* ADC inputs can only be on port A.
|
|
* @{
|
|
*/
|
|
#define ADC_ALS_PWR_PORT GPIO_A_NUM /**< ALS power GPIO control port */
|
|
#define ADC_ALS_PWR_PIN 7 /**< ALS power GPIO control pin */
|
|
#define ADC_ALS_OUT_PIN 6 /**< ALS output ADC input pin on port A */
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name SPI configuration
|
|
*
|
|
* These values configure which CC2538 pins to use for the SPI lines. Both
|
|
* SPI instances can be used independently by providing the corresponding
|
|
* port / pin macros.
|
|
* @{
|
|
*/
|
|
#define SPI0_IN_USE 0
|
|
#define SPI1_IN_USE 0
|
|
#if SPI0_IN_USE
|
|
/** Clock port SPI0 */
|
|
#define SPI0_CLK_PORT GPIO_A_NUM
|
|
/** Clock pin SPI0 */
|
|
#define SPI0_CLK_PIN 2
|
|
/** TX port SPI0 (master mode: MOSI) */
|
|
#define SPI0_TX_PORT GPIO_A_NUM
|
|
/** TX pin SPI0 */
|
|
#define SPI0_TX_PIN 4
|
|
/** RX port SPI0 (master mode: MISO */
|
|
#define SPI0_RX_PORT GPIO_A_NUM
|
|
/** RX pin SPI0 */
|
|
#define SPI0_RX_PIN 5
|
|
#endif /* #if SPI0_IN_USE */
|
|
#if SPI1_IN_USE
|
|
/** Clock port SPI1 */
|
|
#define SPI1_CLK_PORT GPIO_A_NUM
|
|
/** Clock pin SPI1 */
|
|
#define SPI1_CLK_PIN 2
|
|
/** TX port SPI1 (master mode: MOSI) */
|
|
#define SPI1_TX_PORT GPIO_A_NUM
|
|
/** TX pin SPI1 */
|
|
#define SPI1_TX_PIN 4
|
|
/** RX port SPI1 (master mode: MISO) */
|
|
#define SPI1_RX_PORT GPIO_A_NUM
|
|
/** RX pin SPI1 */
|
|
#define SPI1_RX_PIN 5
|
|
#endif /* #if SPI1_IN_USE */
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name Device string used on startup
|
|
* @{
|
|
*/
|
|
#define BOARD_STRING "TI SmartRF06 + cc2538EM"
|
|
/** @} */
|
|
|
|
#endif /* BOARD_H_ */
|
|
|
|
/**
|
|
* @}
|
|
* @}
|
|
*/
|