mirror of
https://github.com/oliverschmidt/contiki.git
synced 2024-12-23 01:29:33 +00:00
abeed93da5
This patch adds a simple, space-efficient driver for the Ethernet interface built into the Intel Quark X1000. It only allocates a single packet descriptor for each of the transmit and receive directions, computes checksums on the CPU, and enables store-and-forward mode for both transmit and receive directions.
373 lines
13 KiB
C
373 lines
13 KiB
C
/*
|
|
* Copyright (C) 2015, Intel Corporation. All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
#include <string.h>
|
|
#include <assert.h>
|
|
#include <stdio.h>
|
|
#include "contiki-net.h"
|
|
#include "eth.h"
|
|
#include "helpers.h"
|
|
#include "net/ip/uip.h"
|
|
#include "pci.h"
|
|
|
|
typedef pci_driver_t quarkX1000_eth_driver_t;
|
|
|
|
/* Refer to Intel Quark SoC X1000 Datasheet, Chapter 15 for more details on
|
|
* Ethernet device operation.
|
|
*
|
|
* This driver puts the Ethernet device into a very simple and space-efficient
|
|
* mode of operation. It only allocates a single packet descriptor for each of
|
|
* the transmit and receive directions, computes checksums on the CPU, and
|
|
* enables store-and-forward mode for both transmit and receive directions.
|
|
*/
|
|
|
|
/* Transmit descriptor */
|
|
typedef struct quarkX1000_eth_tx_desc {
|
|
/* First word of transmit descriptor */
|
|
union {
|
|
struct {
|
|
/* Only valid in half-duplex mode. */
|
|
uint32_t deferred_bit : 1;
|
|
uint32_t err_underflow : 1;
|
|
uint32_t err_excess_defer : 1;
|
|
uint32_t coll_cnt_slot_num : 4;
|
|
uint32_t vlan_frm : 1;
|
|
uint32_t err_excess_coll : 1;
|
|
uint32_t err_late_coll : 1;
|
|
uint32_t err_no_carrier : 1;
|
|
uint32_t err_carrier_loss : 1;
|
|
uint32_t err_ip_payload : 1;
|
|
uint32_t err_frm_flushed : 1;
|
|
uint32_t err_jabber_tout : 1;
|
|
/* OR of all other error bits. */
|
|
uint32_t err_summary : 1;
|
|
uint32_t err_ip_hdr : 1;
|
|
uint32_t tx_timestamp_stat : 1;
|
|
uint32_t vlan_ins_ctrl : 2;
|
|
uint32_t addr2_chained : 1;
|
|
uint32_t tx_end_of_ring : 1;
|
|
uint32_t chksum_ins_ctrl : 2;
|
|
uint32_t replace_crc : 1;
|
|
uint32_t tx_timestamp_en : 1;
|
|
uint32_t dis_pad : 1;
|
|
uint32_t dis_crc : 1;
|
|
uint32_t first_seg_in_frm : 1;
|
|
uint32_t last_seg_in_frm : 1;
|
|
uint32_t intr_on_complete : 1;
|
|
/* When set, descriptor is owned by DMA. */
|
|
uint32_t own : 1;
|
|
};
|
|
uint32_t tdes0;
|
|
};
|
|
/* Second word of transmit descriptor */
|
|
union {
|
|
struct {
|
|
uint32_t tx_buf1_sz : 13;
|
|
uint32_t : 3;
|
|
uint32_t tx_buf2_sz : 13;
|
|
uint32_t src_addr_ins_ctrl : 3;
|
|
};
|
|
uint32_t tdes1;
|
|
};
|
|
/* Pointer to frame data buffer */
|
|
uint8_t *buf1_ptr;
|
|
/* Unused, since this driver initializes only a single descriptor for each
|
|
* direction.
|
|
*/
|
|
uint8_t *buf2_ptr;
|
|
} quarkX1000_eth_tx_desc_t;
|
|
|
|
/* Transmit descriptor */
|
|
typedef struct quarkX1000_eth_rx_desc {
|
|
/* First word of receive descriptor */
|
|
union {
|
|
struct {
|
|
uint32_t ext_stat : 1;
|
|
uint32_t err_crc : 1;
|
|
uint32_t err_dribble_bit : 1;
|
|
uint32_t err_rx_mii : 1;
|
|
uint32_t err_rx_wdt : 1;
|
|
uint32_t frm_type : 1;
|
|
uint32_t err_late_coll : 1;
|
|
uint32_t giant_frm : 1;
|
|
uint32_t last_desc : 1;
|
|
uint32_t first_desc : 1;
|
|
uint32_t vlan_tag : 1;
|
|
uint32_t err_overflow : 1;
|
|
uint32_t length_err : 1;
|
|
uint32_t s_addr_filt_fail : 1;
|
|
uint32_t err_desc : 1;
|
|
uint32_t err_summary : 1;
|
|
uint32_t frm_len : 14;
|
|
uint32_t d_addr_filt_fail : 1;
|
|
uint32_t own : 1;
|
|
};
|
|
uint32_t rdes0;
|
|
};
|
|
/* Second word of receive descriptor */
|
|
union {
|
|
struct {
|
|
uint32_t rx_buf1_sz : 13;
|
|
uint32_t : 1;
|
|
uint32_t addr2_chained : 1;
|
|
uint32_t rx_end_of_ring : 1;
|
|
uint32_t rx_buf2_sz : 13;
|
|
uint32_t : 2;
|
|
uint32_t dis_int_compl : 1;
|
|
};
|
|
uint32_t rdes1;
|
|
};
|
|
/* Pointer to frame data buffer */
|
|
uint8_t *buf1_ptr;
|
|
/* Unused, since this driver initializes only a single descriptor for each
|
|
* direction.
|
|
*/
|
|
uint8_t *buf2_ptr;
|
|
} quarkX1000_eth_rx_desc_t;
|
|
|
|
/* Driver metadata associated with each Ethernet device */
|
|
typedef struct quarkX1000_eth_meta {
|
|
/* Transmit descriptor */
|
|
volatile quarkX1000_eth_tx_desc_t tx_desc;
|
|
/* Transmit DMA packet buffer */
|
|
volatile uint8_t tx_buf[UIP_BUFSIZE];
|
|
/* Receive descriptor */
|
|
volatile quarkX1000_eth_rx_desc_t rx_desc;
|
|
/* Receive DMA packet buffer */
|
|
volatile uint8_t rx_buf[UIP_BUFSIZE];
|
|
} quarkX1000_eth_meta_t;
|
|
|
|
#define LOG_PFX "quarkX1000_eth: "
|
|
|
|
#define MMIO_SZ 0x2000
|
|
|
|
#define MAC_CONF_14_RMII_100M BIT(14)
|
|
#define MAC_CONF_11_DUPLEX BIT(11)
|
|
#define MAC_CONF_3_TX_EN BIT(3)
|
|
#define MAC_CONF_2_RX_EN BIT(2)
|
|
|
|
#define OP_MODE_25_RX_STORE_N_FORWARD BIT(25)
|
|
#define OP_MODE_21_TX_STORE_N_FORWARD BIT(21)
|
|
#define OP_MODE_13_START_TX BIT(13)
|
|
#define OP_MODE_1_START_RX BIT(1)
|
|
|
|
#define REG_ADDR_MAC_CONF 0x0000
|
|
#define REG_ADDR_MACADDR_HI 0x0040
|
|
#define REG_ADDR_MACADDR_LO 0x0044
|
|
#define REG_ADDR_TX_POLL_DEMAND 0x1004
|
|
#define REG_ADDR_RX_POLL_DEMAND 0x1008
|
|
#define REG_ADDR_RX_DESC_LIST 0x100C
|
|
#define REG_ADDR_TX_DESC_LIST 0x1010
|
|
#define REG_ADDR_DMA_OPERATION 0x1018
|
|
|
|
static quarkX1000_eth_driver_t drv;
|
|
static quarkX1000_eth_meta_t meta;
|
|
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \brief Initialize the first Quark X1000 Ethernet MAC.
|
|
*
|
|
* This procedure assumes that an MMIO range for the device was
|
|
* previously assigned, e.g. by firmware.
|
|
*/
|
|
void
|
|
quarkX1000_eth_init(void)
|
|
{
|
|
pci_config_addr_t pci_addr = { .raw = 0 };
|
|
uip_eth_addr mac_addr;
|
|
uint32_t mac_tmp1, mac_tmp2;
|
|
|
|
/* PCI address from section 15.4 of Intel Quark SoC X1000 Datasheet. */
|
|
|
|
pci_addr.dev = 20;
|
|
pci_addr.func = 6;
|
|
|
|
/* Activate MMIO and DMA access. */
|
|
pci_command_enable(pci_addr, PCI_CMD_2_BUS_MST_EN | PCI_CMD_1_MEM_SPACE_EN);
|
|
|
|
printf(LOG_PFX "Activated MMIO and DMA access.\n");
|
|
|
|
pci_addr.reg_off = PCI_CONFIG_REG_BAR0;
|
|
|
|
/* Configure the device MMIO range and initialize the driver structure. */
|
|
pci_init(&drv, pci_addr, (uintptr_t)&meta);
|
|
|
|
/* Read the MAC address from the device. */
|
|
PCI_MMIO_READL(drv, mac_tmp1, REG_ADDR_MACADDR_HI);
|
|
PCI_MMIO_READL(drv, mac_tmp2, REG_ADDR_MACADDR_LO);
|
|
|
|
/* Convert the data read from the device into the format expected by
|
|
* Contiki.
|
|
*/
|
|
mac_addr.addr[5] = (uint8_t)(mac_tmp1 >> 8);
|
|
mac_addr.addr[4] = (uint8_t)mac_tmp1;
|
|
mac_addr.addr[3] = (uint8_t)(mac_tmp2 >> 24);
|
|
mac_addr.addr[2] = (uint8_t)(mac_tmp2 >> 16);
|
|
mac_addr.addr[1] = (uint8_t)(mac_tmp2 >> 8);
|
|
mac_addr.addr[0] = (uint8_t)mac_tmp2;
|
|
|
|
printf(LOG_PFX "MAC address = %02x:%02x:%02x:%02x:%02x:%02x.\n",
|
|
mac_addr.addr[0],
|
|
mac_addr.addr[1],
|
|
mac_addr.addr[2],
|
|
mac_addr.addr[3],
|
|
mac_addr.addr[4],
|
|
mac_addr.addr[5]
|
|
);
|
|
|
|
uip_setethaddr(mac_addr);
|
|
|
|
/* Initialize transmit descriptor. */
|
|
meta.tx_desc.tdes0 = 0;
|
|
meta.tx_desc.tdes1 = 0;
|
|
|
|
meta.tx_desc.buf1_ptr = (uint8_t *)meta.tx_buf;
|
|
meta.tx_desc.tx_end_of_ring = 1;
|
|
meta.tx_desc.first_seg_in_frm = 1;
|
|
meta.tx_desc.last_seg_in_frm = 1;
|
|
meta.tx_desc.tx_end_of_ring = 1;
|
|
|
|
/* Initialize receive descriptor. */
|
|
meta.rx_desc.rdes0 = 0;
|
|
meta.rx_desc.rdes1 = 0;
|
|
|
|
meta.rx_desc.buf1_ptr = (uint8_t *)meta.rx_buf;
|
|
meta.rx_desc.own = 1;
|
|
meta.rx_desc.first_desc = 1;
|
|
meta.rx_desc.last_desc = 1;
|
|
meta.rx_desc.rx_buf1_sz = UIP_BUFSIZE;
|
|
meta.rx_desc.rx_end_of_ring = 1;
|
|
|
|
/* Install transmit and receive descriptors. */
|
|
PCI_MMIO_WRITEL(drv, REG_ADDR_RX_DESC_LIST, (uint32_t)&meta.rx_desc);
|
|
PCI_MMIO_WRITEL(drv, REG_ADDR_TX_DESC_LIST, (uint32_t)&meta.tx_desc);
|
|
|
|
PCI_MMIO_WRITEL(drv, REG_ADDR_MAC_CONF,
|
|
/* Set the RMII speed to 100Mbps */
|
|
MAC_CONF_14_RMII_100M |
|
|
/* Enable full-duplex mode */
|
|
MAC_CONF_11_DUPLEX |
|
|
/* Enable transmitter */
|
|
MAC_CONF_3_TX_EN |
|
|
/* Enable receiver */
|
|
MAC_CONF_2_RX_EN);
|
|
|
|
PCI_MMIO_WRITEL(drv, REG_ADDR_DMA_OPERATION,
|
|
/* Enable receive store-and-forward mode for simplicity. */
|
|
OP_MODE_25_RX_STORE_N_FORWARD |
|
|
/* Enable transmit store-and-forward mode for simplicity. */
|
|
OP_MODE_21_TX_STORE_N_FORWARD |
|
|
/* Place the transmitter state machine in the Running
|
|
state. */
|
|
OP_MODE_13_START_TX |
|
|
/* Place the receiver state machine in the Running state. */
|
|
OP_MODE_1_START_RX);
|
|
|
|
printf(LOG_PFX "Enabled 100M full-duplex mode.\n");
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \brief Poll for a received Ethernet frame.
|
|
* \param frame_len Will be set to the size of the received Ethernet frame or
|
|
* zero if no frame is available.
|
|
*
|
|
* If a frame is received, this procedure copies it into the
|
|
* global uip_buf buffer.
|
|
*/
|
|
void
|
|
quarkX1000_eth_poll(uint16_t *frame_len)
|
|
{
|
|
uint16_t frm_len = 0;
|
|
|
|
/* Check whether the RX descriptor is still owned by the device. If not,
|
|
* process the received frame or an error that may have occurred.
|
|
*/
|
|
if(meta.rx_desc.own == 0) {
|
|
if(meta.rx_desc.err_summary) {
|
|
fprintf(stderr,
|
|
LOG_PFX "Error receiving frame: RDES0 = %08x, RDES1 = %08x.\n",
|
|
meta.rx_desc.rdes0, meta.rx_desc.rdes1);
|
|
assert(0);
|
|
}
|
|
|
|
frm_len = meta.rx_desc.frm_len;
|
|
assert(frm_len <= UIP_BUFSIZE);
|
|
memcpy(uip_buf, (void *)meta.rx_buf, frm_len);
|
|
|
|
/* Return ownership of the RX descriptor to the device. */
|
|
meta.rx_desc.own = 1;
|
|
|
|
/* Request that the device check for an available RX descriptor, since
|
|
* ownership of the descriptor was just transferred to the device.
|
|
*/
|
|
PCI_MMIO_WRITEL(drv, REG_ADDR_RX_POLL_DEMAND, 1);
|
|
}
|
|
|
|
*frame_len = frm_len;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \brief Transmit the current Ethernet frame.
|
|
*
|
|
* This procedure will block indefinitely until the Ethernet device is
|
|
* ready to accept a new outgoing frame. It then copies the current
|
|
* Ethernet frame from the global uip_buf buffer to the device DMA
|
|
* buffer and signals to the device that a new frame is available to be
|
|
* transmitted.
|
|
*/
|
|
void
|
|
quarkX1000_eth_send(void)
|
|
{
|
|
/* Wait until the TX descriptor is no longer owned by the device. */
|
|
while(meta.tx_desc.own == 1);
|
|
|
|
/* Check whether an error occurred transmitting the previous frame. */
|
|
if(meta.tx_desc.err_summary) {
|
|
fprintf(stderr,
|
|
LOG_PFX "Error transmitting frame: TDES0 = %08x, TDES1 = %08x.\n",
|
|
meta.tx_desc.tdes0, meta.tx_desc.tdes1);
|
|
assert(0);
|
|
}
|
|
|
|
/* Transmit the next frame. */
|
|
assert(uip_len <= UIP_BUFSIZE);
|
|
memcpy((void *)meta.tx_buf, uip_buf, uip_len);
|
|
|
|
meta.tx_desc.tx_buf1_sz = uip_len;
|
|
|
|
meta.tx_desc.own = 1;
|
|
|
|
/* Request that the device check for an available TX descriptor, since
|
|
* ownership of the descriptor was just transferred to the device.
|
|
*/
|
|
PCI_MMIO_WRITEL(drv, REG_ADDR_TX_POLL_DEMAND, 1);
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|