prog8/compiler/res/prog8lib/cx16/syslib.p8

901 lines
30 KiB
Lua

; Prog8 definitions for the CommanderX16
; Including memory registers, I/O registers, Basic and Kernal subroutines.
;
; Written by Irmen de Jong (irmen@razorvine.net) - license: GNU GPL 3.0
;
; indent format: TABS, size=8
c64 {
; ---- kernal routines, these are the same as on the Commodore-64 (hence the same block name) ----
; STROUT --> use txt.print
; CLEARSCR -> use txt.clear_screen
; HOMECRSR -> use txt.home or txt.plot
romsub $FF81 = CINT() clobbers(A,X,Y) ; (alias: SCINIT) initialize screen editor and video chip
romsub $FF84 = IOINIT() clobbers(A, X) ; initialize I/O devices (CIA, SID, IRQ)
romsub $FF87 = RAMTAS() clobbers(A,X,Y) ; initialize RAM, tape buffer, screen
romsub $FF8A = RESTOR() clobbers(A,X,Y) ; restore default I/O vectors
romsub $FF8D = VECTOR(uword userptr @ XY, ubyte dir @ Pc) clobbers(A,Y) ; read/set I/O vector table
romsub $FF90 = SETMSG(ubyte value @ A) ; set Kernal message control flag
romsub $FF93 = SECOND(ubyte address @ A) clobbers(A) ; (alias: LSTNSA) send secondary address after LISTEN
romsub $FF96 = TKSA(ubyte address @ A) clobbers(A) ; (alias: TALKSA) send secondary address after TALK
romsub $FF99 = MEMTOP(uword address @ XY, ubyte dir @ Pc) -> uword @ XY ; read/set top of memory pointer. NOTE: as a Cx16 extension, also returns the number of RAM memory banks in register A ! See cx16.numbanks()
romsub $FF9C = MEMBOT(uword address @ XY, ubyte dir @ Pc) -> uword @ XY ; read/set bottom of memory pointer
romsub $FF9F = SCNKEY() clobbers(A,X,Y) ; scan the keyboard
romsub $FFA2 = SETTMO(ubyte timeout @ A) ; set time-out flag for IEEE bus
romsub $FFA5 = ACPTR() -> ubyte @ A ; (alias: IECIN) input byte from serial bus
romsub $FFA8 = CIOUT(ubyte databyte @ A) ; (alias: IECOUT) output byte to serial bus
romsub $FFAB = UNTLK() clobbers(A) ; command serial bus device to UNTALK
romsub $FFAE = UNLSN() clobbers(A) ; command serial bus device to UNLISTEN
romsub $FFB1 = LISTEN(ubyte device @ A) clobbers(A) ; command serial bus device to LISTEN
romsub $FFB4 = TALK(ubyte device @ A) clobbers(A) ; command serial bus device to TALK
romsub $FFB7 = READST() -> ubyte @ A ; read I/O status word
romsub $FFBA = SETLFS(ubyte logical @ A, ubyte device @ X, ubyte secondary @ Y) ; set logical file parameters
romsub $FFBD = SETNAM(ubyte namelen @ A, str filename @ XY) ; set filename parameters
romsub $FFC0 = OPEN() clobbers(X,Y) -> ubyte @Pc, ubyte @A ; (via 794 ($31A)) open a logical file
romsub $FFC3 = CLOSE(ubyte logical @ A) clobbers(A,X,Y) ; (via 796 ($31C)) close a logical file
romsub $FFC6 = CHKIN(ubyte logical @ X) clobbers(A,X) -> ubyte @Pc ; (via 798 ($31E)) define an input channel
romsub $FFC9 = CHKOUT(ubyte logical @ X) clobbers(A,X) ; (via 800 ($320)) define an output channel
romsub $FFCC = CLRCHN() clobbers(A,X) ; (via 802 ($322)) restore default devices
romsub $FFCF = CHRIN() clobbers(X, Y) -> ubyte @ A ; (via 804 ($324)) input a character (for keyboard, read a whole line from the screen) A=byte read.
romsub $FFD2 = CHROUT(ubyte char @ A) ; (via 806 ($326)) output a character
romsub $FFD5 = LOAD(ubyte verify @ A, uword address @ XY) -> ubyte @Pc, ubyte @ A, uword @ XY ; (via 816 ($330)) load from device
romsub $FFD8 = SAVE(ubyte zp_startaddr @ A, uword endaddr @ XY) -> ubyte @ Pc, ubyte @ A ; (via 818 ($332)) save to a device
romsub $FFDB = SETTIM(ubyte low @ A, ubyte middle @ X, ubyte high @ Y) ; set the software clock
romsub $FFDE = RDTIM() -> ubyte @ A, ubyte @ X, ubyte @ Y ; read the software clock (A=lo,X=mid,Y=high)
romsub $FFE1 = STOP() clobbers(X) -> ubyte @ Pz, ubyte @ A ; (via 808 ($328)) check the STOP key (and some others in A)
romsub $FFE4 = GETIN() clobbers(X,Y) -> ubyte @Pc, ubyte @ A ; (via 810 ($32A)) get a character
romsub $FFE7 = CLALL() clobbers(A,X) ; (via 812 ($32C)) close all files
romsub $FFEA = UDTIM() clobbers(A,X) ; update the software clock
romsub $FFED = SCREEN() -> ubyte @ X, ubyte @ Y ; read number of screen rows and columns
romsub $FFF0 = PLOT(ubyte col @ Y, ubyte row @ X, ubyte dir @ Pc) -> ubyte @ X, ubyte @ Y ; read/set position of cursor on screen. Use txt.plot for a 'safe' wrapper that preserves X.
romsub $FFF3 = IOBASE() -> uword @ XY ; read base address of I/O devices
; ---- utility
asmsub STOP2() -> ubyte @A {
; -- check if STOP key was pressed, returns true if so. More convenient to use than STOP() because that only sets the carry status flag.
%asm {{
phx
jsr c64.STOP
beq +
plx
lda #0
rts
+ plx
lda #1
rts
}}
}
asmsub RDTIM16() -> uword @AY {
; -- like RDTIM() but only returning the lower 16 bits in AY for convenience
%asm {{
phx
jsr c64.RDTIM
pha
txa
tay
pla
plx
rts
}}
}
}
cx16 {
; irq and hardware vectors:
&uword CINV = $0314 ; IRQ vector (in ram)
&uword CBINV = $0316 ; BRK vector (in ram)
&uword NMINV = $0318 ; NMI vector (in ram)
&uword NMI_VEC = $FFFA ; 65c02 nmi vector, determined by the kernal if banked in
&uword RESET_VEC = $FFFC ; 65c02 reset vector, determined by the kernal if banked in
&uword IRQ_VEC = $FFFE ; 65c02 interrupt vector, determined by the kernal if banked in
; the sixteen virtual 16-bit registers in both normal unsigned mode and signed mode (s)
&uword r0 = $0002
&uword r1 = $0004
&uword r2 = $0006
&uword r3 = $0008
&uword r4 = $000a
&uword r5 = $000c
&uword r6 = $000e
&uword r7 = $0010
&uword r8 = $0012
&uword r9 = $0014
&uword r10 = $0016
&uword r11 = $0018
&uword r12 = $001a
&uword r13 = $001c
&uword r14 = $001e
&uword r15 = $0020
&word r0s = $0002
&word r1s = $0004
&word r2s = $0006
&word r3s = $0008
&word r4s = $000a
&word r5s = $000c
&word r6s = $000e
&word r7s = $0010
&word r8s = $0012
&word r9s = $0014
&word r10s = $0016
&word r11s = $0018
&word r12s = $001a
&word r13s = $001c
&word r14s = $001e
&word r15s = $0020
&ubyte r0L = $0002
&ubyte r1L = $0004
&ubyte r2L = $0006
&ubyte r3L = $0008
&ubyte r4L = $000a
&ubyte r5L = $000c
&ubyte r6L = $000e
&ubyte r7L = $0010
&ubyte r8L = $0012
&ubyte r9L = $0014
&ubyte r10L = $0016
&ubyte r11L = $0018
&ubyte r12L = $001a
&ubyte r13L = $001c
&ubyte r14L = $001e
&ubyte r15L = $0020
&ubyte r0H = $0003
&ubyte r1H = $0005
&ubyte r2H = $0007
&ubyte r3H = $0009
&ubyte r4H = $000b
&ubyte r5H = $000d
&ubyte r6H = $000f
&ubyte r7H = $0011
&ubyte r8H = $0013
&ubyte r9H = $0015
&ubyte r10H = $0017
&ubyte r11H = $0019
&ubyte r12H = $001b
&ubyte r13H = $001d
&ubyte r14H = $001f
&ubyte r15H = $0021
&byte r0sL = $0002
&byte r1sL = $0004
&byte r2sL = $0006
&byte r3sL = $0008
&byte r4sL = $000a
&byte r5sL = $000c
&byte r6sL = $000e
&byte r7sL = $0010
&byte r8sL = $0012
&byte r9sL = $0014
&byte r10sL = $0016
&byte r11sL = $0018
&byte r12sL = $001a
&byte r13sL = $001c
&byte r14sL = $001e
&byte r15sL = $0020
&byte r0sH = $0003
&byte r1sH = $0005
&byte r2sH = $0007
&byte r3sH = $0009
&byte r4sH = $000b
&byte r5sH = $000d
&byte r6sH = $000f
&byte r7sH = $0011
&byte r8sH = $0013
&byte r9sH = $0015
&byte r10sH = $0017
&byte r11sH = $0019
&byte r12sH = $001b
&byte r13sH = $001d
&byte r14sH = $001f
&byte r15sH = $0021
; VERA registers
const uword VERA_BASE = $9F20
&ubyte VERA_ADDR_L = VERA_BASE + $0000
&ubyte VERA_ADDR_M = VERA_BASE + $0001
&ubyte VERA_ADDR_H = VERA_BASE + $0002
&ubyte VERA_DATA0 = VERA_BASE + $0003
&ubyte VERA_DATA1 = VERA_BASE + $0004
&ubyte VERA_CTRL = VERA_BASE + $0005
&ubyte VERA_IEN = VERA_BASE + $0006
&ubyte VERA_ISR = VERA_BASE + $0007
&ubyte VERA_IRQ_LINE_L = VERA_BASE + $0008
&ubyte VERA_DC_VIDEO = VERA_BASE + $0009
&ubyte VERA_DC_HSCALE = VERA_BASE + $000A
&ubyte VERA_DC_VSCALE = VERA_BASE + $000B
&ubyte VERA_DC_BORDER = VERA_BASE + $000C
&ubyte VERA_DC_HSTART = VERA_BASE + $0009
&ubyte VERA_DC_HSTOP = VERA_BASE + $000A
&ubyte VERA_DC_VSTART = VERA_BASE + $000B
&ubyte VERA_DC_VSTOP = VERA_BASE + $000C
&ubyte VERA_L0_CONFIG = VERA_BASE + $000D
&ubyte VERA_L0_MAPBASE = VERA_BASE + $000E
&ubyte VERA_L0_TILEBASE = VERA_BASE + $000F
&ubyte VERA_L0_HSCROLL_L = VERA_BASE + $0010
&ubyte VERA_L0_HSCROLL_H = VERA_BASE + $0011
&ubyte VERA_L0_VSCROLL_L = VERA_BASE + $0012
&ubyte VERA_L0_VSCROLL_H = VERA_BASE + $0013
&ubyte VERA_L1_CONFIG = VERA_BASE + $0014
&ubyte VERA_L1_MAPBASE = VERA_BASE + $0015
&ubyte VERA_L1_TILEBASE = VERA_BASE + $0016
&ubyte VERA_L1_HSCROLL_L = VERA_BASE + $0017
&ubyte VERA_L1_HSCROLL_H = VERA_BASE + $0018
&ubyte VERA_L1_VSCROLL_L = VERA_BASE + $0019
&ubyte VERA_L1_VSCROLL_H = VERA_BASE + $001A
&ubyte VERA_AUDIO_CTRL = VERA_BASE + $001B
&ubyte VERA_AUDIO_RATE = VERA_BASE + $001C
&ubyte VERA_AUDIO_DATA = VERA_BASE + $001D
&ubyte VERA_SPI_DATA = VERA_BASE + $001E
&ubyte VERA_SPI_CTRL = VERA_BASE + $001F
; VERA_PSG_BASE = $1F9C0
; VERA_PALETTE_BASE = $1FA00
; VERA_SPRITES_BASE = $1FC00
; I/O
const uword via1 = $9f00 ;VIA 6522 #1
&ubyte d1prb = via1+0
&ubyte d1pra = via1+1
&ubyte d1ddrb = via1+2
&ubyte d1ddra = via1+3
&ubyte d1t1l = via1+4
&ubyte d1t1h = via1+5
&ubyte d1t1ll = via1+6
&ubyte d1t1lh = via1+7
&ubyte d1t2l = via1+8
&ubyte d1t2h = via1+9
&ubyte d1sr = via1+10
&ubyte d1acr = via1+11
&ubyte d1pcr = via1+12
&ubyte d1ifr = via1+13
&ubyte d1ier = via1+14
&ubyte d1ora = via1+15
const uword via2 = $9f10 ;VIA 6522 #2
&ubyte d2prb = via2+0
&ubyte d2pra = via2+1
&ubyte d2ddrb = via2+2
&ubyte d2ddra = via2+3
&ubyte d2t1l = via2+4
&ubyte d2t1h = via2+5
&ubyte d2t1ll = via2+6
&ubyte d2t1lh = via2+7
&ubyte d2t2l = via2+8
&ubyte d2t2h = via2+9
&ubyte d2sr = via2+10
&ubyte d2acr = via2+11
&ubyte d2pcr = via2+12
&ubyte d2ifr = via2+13
&ubyte d2ier = via2+14
&ubyte d2ora = via2+15
&ubyte ym2151adr = $9f40
&ubyte ym2151dat = $9f41
const uword extdev = $9f60
; ---- Commander X-16 additions on top of C64 kernal routines ----
; spelling of the names is taken from the Commander X-16 rom sources
; supported C128 additions
romsub $ff4a = close_all(ubyte device @A) clobbers(A,X,Y)
romsub $ff59 = lkupla(ubyte la @A) clobbers(A,X,Y)
romsub $ff5c = lkupsa(ubyte sa @Y) clobbers(A,X,Y)
romsub $ff5f = screen_set_mode(ubyte mode @A) clobbers(A, X, Y) -> ubyte @Pc
romsub $ff62 = screen_set_charset(ubyte charset @A, uword charsetptr @XY) clobbers(A,X,Y) ; incompatible with C128 dlchr()
; not yet supported: romsub $ff65 = pfkey() clobbers(A,X,Y)
romsub $ff6e = jsrfar()
romsub $ff74 = fetch(ubyte bank @X, ubyte index @Y) clobbers(X) -> ubyte @A
romsub $ff77 = stash(ubyte data @A, ubyte bank @X, ubyte index @Y) clobbers(X)
romsub $ff7a = cmpare(ubyte data @A, ubyte bank @X, ubyte index @Y) clobbers(X)
romsub $ff7d = primm()
; X16 additions
romsub $ff44 = macptr() clobbers(A,X,Y)
romsub $ff47 = enter_basic(ubyte cold_or_warm @Pc) clobbers(A,X,Y)
romsub $ff68 = mouse_config(ubyte shape @A, ubyte scale @X) clobbers (A, X, Y)
romsub $ff6b = mouse_get(ubyte zpdataptr @X) -> ubyte @A
romsub $ff71 = mouse_scan() clobbers(A, X, Y)
romsub $ff53 = joystick_scan() clobbers(A, X, Y)
romsub $ff56 = joystick_get(ubyte joynr @A) -> ubyte @A, ubyte @X, ubyte @Y
romsub $ff4d = clock_set_date_time(uword yearmonth @R0, uword dayhours @R1, uword minsecs @R2, ubyte jiffies @R3) clobbers(A, X, Y)
romsub $ff50 = clock_get_date_time() clobbers(A, X, Y) -> uword @R0, uword @R1, uword @R2, ubyte @R3 ; result registers see clock_set_date_time()
asmsub mouse_pos() -> ubyte @A {
; -- short wrapper around mouse_get() kernal routine:
; -- gets the position of the mouse cursor in cx16.r0 and cx16.r1 (x/y coordinate), returns mouse button status.
%asm {{
phx
ldx #cx16.r0
jsr cx16.mouse_get
plx
rts
}}
}
; It's not documented what registers are clobbered, so we assume the worst for all following kernal routines...:
; high level graphics & fonts
romsub $ff20 = GRAPH_init(uword vectors @R0) clobbers(A,X,Y)
romsub $ff23 = GRAPH_clear() clobbers(A,X,Y)
romsub $ff26 = GRAPH_set_window(uword x @R0, uword y @R1, uword width @R2, uword height @R3) clobbers(A,X,Y)
romsub $ff29 = GRAPH_set_colors(ubyte stroke @A, ubyte fill @X, ubyte background @Y) clobbers (A,X,Y)
romsub $ff2c = GRAPH_draw_line(uword x1 @R0, uword y1 @R1, uword x2 @R2, uword y2 @R3) clobbers(A,X,Y)
romsub $ff2f = GRAPH_draw_rect(uword x @R0, uword y @R1, uword width @R2, uword height @R3, uword cornerradius @R4, ubyte fill @Pc) clobbers(A,X,Y)
romsub $ff32 = GRAPH_move_rect(uword sx @R0, uword sy @R1, uword tx @R2, uword ty @R3, uword width @R4, uword height @R5) clobbers(A,X,Y)
romsub $ff35 = GRAPH_draw_oval(uword x @R0, uword y @R1, uword width @R2, uword height @R3, ubyte fill @Pc) clobbers(A,X,Y)
romsub $ff38 = GRAPH_draw_image(uword x @R0, uword y @R1, uword ptr @R2, uword width @R3, uword height @R4) clobbers(A,X,Y)
romsub $ff3b = GRAPH_set_font(uword fontptr @R0) clobbers(A,X,Y)
romsub $ff3e = GRAPH_get_char_size(ubyte baseline @A, ubyte width @X, ubyte height_or_style @Y, ubyte is_control @Pc) clobbers(A,X,Y)
romsub $ff41 = GRAPH_put_char(uword x @R0, uword y @R1, ubyte char @A) clobbers(A,X,Y)
romsub $ff41 = GRAPH_put_next_char(ubyte char @A) clobbers(A,X,Y) ; alias for the routine above that doesn't reset the position of the initial character
; framebuffer
romsub $fef6 = FB_init() clobbers(A,X,Y)
romsub $fef9 = FB_get_info() clobbers(X,Y) -> byte @A, uword @R0, uword @R1 ; width=r0, height=r1
romsub $fefc = FB_set_palette(uword pointer @R0, ubyte index @A, ubyte bytecount @X) clobbers(A,X,Y)
romsub $feff = FB_cursor_position(uword x @R0, uword y @R1) clobbers(A,X,Y)
romsub $feff = FB_cursor_position2() clobbers(A,X,Y) ; alias for the previous routine, but avoiding having to respecify both x and y every time
romsub $ff02 = FB_cursor_next_line(uword x @R0) clobbers(A,X,Y)
romsub $ff05 = FB_get_pixel() clobbers(X,Y) -> ubyte @A
romsub $ff08 = FB_get_pixels(uword pointer @R0, uword count @R1) clobbers(A,X,Y)
romsub $ff0b = FB_set_pixel(ubyte color @A) clobbers(A,X,Y)
romsub $ff0e = FB_set_pixels(uword pointer @R0, uword count @R1) clobbers(A,X,Y)
romsub $ff11 = FB_set_8_pixels(ubyte pattern @A, ubyte color @X) clobbers(A,X,Y)
romsub $ff14 = FB_set_8_pixels_opaque(ubyte pattern @R0, ubyte mask @A, ubyte color1 @X, ubyte color2 @Y) clobbers(A,X,Y)
romsub $ff17 = FB_fill_pixels(uword count @R0, uword pstep @R1, ubyte color @A) clobbers(A,X,Y)
romsub $ff1a = FB_filter_pixels(uword pointer @ R0, uword count @R1) clobbers(A,X,Y)
romsub $ff1d = FB_move_pixels(uword sx @R0, uword sy @R1, uword tx @R2, uword ty @R3, uword count @R4) clobbers(A,X,Y)
; misc
romsub $fef0 = sprite_set_image(uword pixels @R0, uword mask @R1, ubyte bpp @R2, ubyte number @A, ubyte width @X, ubyte height @Y, ubyte apply_mask @Pc) clobbers(A,X,Y) -> ubyte @Pc
romsub $fef3 = sprite_set_position(uword x @R0, uword y @R1, ubyte number @A) clobbers(A,X,Y)
romsub $fee4 = memory_fill(uword address @R0, uword num_bytes @R1, ubyte value @A) clobbers(A,X,Y)
romsub $fee7 = memory_copy(uword source @R0, uword target @R1, uword num_bytes @R2) clobbers(A,X,Y)
romsub $feea = memory_crc(uword address @R0, uword num_bytes @R1) clobbers(A,X,Y) -> uword @R2
romsub $feed = memory_decompress(uword input @R0, uword output @R1) clobbers(A,X,Y) -> uword @R1 ; last address +1 is result in R1
romsub $fedb = console_init(uword x @R0, uword y @R1, uword width @R2, uword height @R3) clobbers(A,X,Y)
romsub $fede = console_put_char(ubyte char @A, ubyte wrapping @Pc) clobbers(A,X,Y)
romsub $fee1 = console_get_char() clobbers(X,Y) -> ubyte @A
romsub $fed8 = console_put_image(uword pointer @R0, uword width @R1, uword height @R2) clobbers(A,X,Y)
romsub $fed5 = console_set_paging_message(uword msgptr @R0) clobbers(A,X,Y)
romsub $fed2 = kbdbuf_put(ubyte key @A) clobbers(A,X,Y)
romsub $fecf = entropy_get() -> ubyte @A, ubyte @X, ubyte @Y
romsub $fecc = monitor() clobbers(A,X,Y)
; ---- end of kernal routines ----
; ---- utilities -----
inline asmsub rombank(ubyte bank @A) {
; -- set the rom banks
%asm {{
sta $01 ; rom bank register (v39+, used to be cx16.d1prb $9f60 in v38)
}}
}
inline asmsub rambank(ubyte bank @A) {
; -- set the ram bank
%asm {{
sta $00 ; ram bank register (v39+, used to be cx16.d1pra $9f61 in v38)
}}
}
inline asmsub getrombank() -> ubyte @A {
; -- get the current rom bank
%asm {{
lda $01 ; rom bank register (v39+, used to be cx16.d1prb $9f60 in v38)
}}
}
inline asmsub getrambank() -> ubyte @A {
; -- get the current ram bank
%asm {{
lda $00 ; ram bank register (v39+, used to be cx16.d1pra $9f61 in v38)
}}
}
asmsub numbanks() -> ubyte @A {
; -- uses MEMTOP's cx16 extension to query the number of available RAM banks. (each is 8 Kb)
%asm {{
phx
sec
jsr c64.MEMTOP
plx
rts
}}
}
asmsub vpeek(ubyte bank @A, uword address @XY) -> ubyte @A {
; -- get a byte from VERA's video memory
; note: inefficient when reading multiple sequential bytes!
%asm {{
pha
lda #1
sta cx16.VERA_CTRL
pla
and #1
sta cx16.VERA_ADDR_H
sty cx16.VERA_ADDR_M
stx cx16.VERA_ADDR_L
lda cx16.VERA_DATA1
rts
}}
}
asmsub vaddr(ubyte bank @A, uword address @R0, ubyte addrsel @R1, byte autoIncrOrDecrByOne @Y) clobbers(A) {
; -- setup the VERA's data address register 0 or 1
%asm {{
and #1
pha
lda cx16.r1
and #1
sta cx16.VERA_CTRL
lda cx16.r0
sta cx16.VERA_ADDR_L
lda cx16.r0+1
sta cx16.VERA_ADDR_M
pla
cpy #0
bmi ++
beq +
ora #%00010000
+ sta cx16.VERA_ADDR_H
rts
+ ora #%00011000
sta cx16.VERA_ADDR_H
rts
}}
}
asmsub vpoke(ubyte bank @A, uword address @R0, ubyte value @Y) clobbers(A) {
; -- write a single byte to VERA's video memory
; note: inefficient when writing multiple sequential bytes!
%asm {{
stz cx16.VERA_CTRL
and #1
sta cx16.VERA_ADDR_H
lda cx16.r0
sta cx16.VERA_ADDR_L
lda cx16.r0+1
sta cx16.VERA_ADDR_M
sty cx16.VERA_DATA0
rts
}}
}
asmsub vpoke_or(ubyte bank @A, uword address @R0, ubyte value @Y) clobbers (A) {
; -- or a single byte to the value already in the VERA's video memory at that location
; note: inefficient when writing multiple sequential bytes!
%asm {{
stz cx16.VERA_CTRL
and #1
sta cx16.VERA_ADDR_H
lda cx16.r0
sta cx16.VERA_ADDR_L
lda cx16.r0+1
sta cx16.VERA_ADDR_M
tya
ora cx16.VERA_DATA0
sta cx16.VERA_DATA0
rts
}}
}
asmsub vpoke_and(ubyte bank @A, uword address @R0, ubyte value @Y) clobbers(A) {
; -- and a single byte to the value already in the VERA's video memory at that location
; note: inefficient when writing multiple sequential bytes!
%asm {{
stz cx16.VERA_CTRL
and #1
sta cx16.VERA_ADDR_H
lda cx16.r0
sta cx16.VERA_ADDR_L
lda cx16.r0+1
sta cx16.VERA_ADDR_M
tya
and cx16.VERA_DATA0
sta cx16.VERA_DATA0
rts
}}
}
asmsub vpoke_xor(ubyte bank @A, uword address @R0, ubyte value @Y) clobbers (A) {
; -- xor a single byte to the value already in the VERA's video memory at that location
; note: inefficient when writing multiple sequential bytes!
%asm {{
stz cx16.VERA_CTRL
and #1
sta cx16.VERA_ADDR_H
lda cx16.r0
sta cx16.VERA_ADDR_L
lda cx16.r0+1
sta cx16.VERA_ADDR_M
tya
eor cx16.VERA_DATA0
sta cx16.VERA_DATA0
rts
}}
}
inline asmsub joystick_get2(ubyte joynr @A) clobbers(Y) -> uword @AX {
; convenience routine to get the joystick state without requiring inline assembly that deals with the multiple return values.
; Also disables interrupts to avoid the IRQ race condition mentioned here: https://github.com/commanderx16/x16-rom/issues/203
; TODO once that issue is resolved, this routine can be redefined as: romsub $ff56 = joystick_get2(ubyte joynr @A) clobbers(Y) -> uword @AX
%asm {{
sei
jsr cx16.joystick_get
cli
}}
}
sub FB_set_pixels_from_buf(uword buffer, uword count) {
%asm {{
; -- This is replacement code for the normal FB_set_pixels subroutine in ROM
; However that routine contains a bug in the current v38 ROM that makes it crash when count > 255.
; So the code below replaces that. Once the ROM is patched this routine is no longer necessary.
; See https://github.com/commanderx16/x16-rom/issues/179
phx
lda buffer
ldy buffer+1
sta P8ZP_SCRATCH_W1
sty P8ZP_SCRATCH_W1+1
jsr _pixels
plx
rts
_pixels lda count+1
beq +
ldx #0
- jsr _loop
inc P8ZP_SCRATCH_W1+1
dec count+1
bne -
+ ldx count
_loop ldy #0
- lda (P8ZP_SCRATCH_W1),y
sta cx16.VERA_DATA0
iny
dex
bne -
rts
}}
}
; ---- system stuff -----
asmsub init_system() {
; Initializes the machine to a sane starting state.
; Called automatically by the loader program logic.
%asm {{
sei
cld
lda #$80
sta VERA_CTRL
stz $01 ; select rom bank 0 (enable kernal)
jsr c64.IOINIT
jsr c64.RESTOR
jsr c64.CINT
lda #$90 ; black
jsr c64.CHROUT
lda #1 ; swap fg/bg
jsr c64.CHROUT
lda #$9e ; yellow
jsr c64.CHROUT
lda #147 ; clear screen
jsr c64.CHROUT
lda #0
tax
tay
clc
clv
cli
rts
}}
}
asmsub init_system_phase2() {
%asm {{
sei
lda cx16.CINV
sta restore_irq._orig_irqvec
lda cx16.CINV+1
sta restore_irq._orig_irqvec+1
cli
rts
}}
}
asmsub set_irq(uword handler @AY, ubyte useKernal @Pc) clobbers(A) {
%asm {{
sta _modified+1
sty _modified+2
lda #0
adc #0
sta _use_kernal
sei
lda #<_irq_handler
sta cx16.CINV
lda #>_irq_handler
sta cx16.CINV+1
lda cx16.VERA_IEN
ora #%00000001 ; enable the vsync irq
sta cx16.VERA_IEN
cli
rts
_irq_handler jsr _irq_handler_init
_modified jsr $ffff ; modified
jsr _irq_handler_end
lda _use_kernal
bne +
; end irq processing - don't use kernal's irq handling
lda cx16.VERA_ISR
ora #1
sta cx16.VERA_ISR ; clear Vera Vsync irq status
ply
plx
pla
rti
+ jmp (restore_irq._orig_irqvec) ; continue with normal kernal irq routine
_use_kernal .byte 0
_irq_handler_init
; save all zp scratch registers and the X register as these might be clobbered by the irq routine
stx IRQ_X_REG
lda P8ZP_SCRATCH_B1
sta IRQ_SCRATCH_ZPB1
lda P8ZP_SCRATCH_REG
sta IRQ_SCRATCH_ZPREG
lda P8ZP_SCRATCH_W1
sta IRQ_SCRATCH_ZPWORD1
lda P8ZP_SCRATCH_W1+1
sta IRQ_SCRATCH_ZPWORD1+1
lda P8ZP_SCRATCH_W2
sta IRQ_SCRATCH_ZPWORD2
lda P8ZP_SCRATCH_W2+1
sta IRQ_SCRATCH_ZPWORD2+1
; stack protector; make sure we don't clobber the top of the evaluation stack
dex
dex
dex
dex
dex
dex
cld
rts
_irq_handler_end
; restore all zp scratch registers and the X register
lda IRQ_SCRATCH_ZPB1
sta P8ZP_SCRATCH_B1
lda IRQ_SCRATCH_ZPREG
sta P8ZP_SCRATCH_REG
lda IRQ_SCRATCH_ZPWORD1
sta P8ZP_SCRATCH_W1
lda IRQ_SCRATCH_ZPWORD1+1
sta P8ZP_SCRATCH_W1+1
lda IRQ_SCRATCH_ZPWORD2
sta P8ZP_SCRATCH_W2
lda IRQ_SCRATCH_ZPWORD2+1
sta P8ZP_SCRATCH_W2+1
ldx IRQ_X_REG
rts
IRQ_X_REG .byte 0
IRQ_SCRATCH_ZPB1 .byte 0
IRQ_SCRATCH_ZPREG .byte 0
IRQ_SCRATCH_ZPWORD1 .word 0
IRQ_SCRATCH_ZPWORD2 .word 0
}}
}
asmsub restore_irq() clobbers(A) {
%asm {{
sei
lda _orig_irqvec
sta cx16.CINV
lda _orig_irqvec+1
sta cx16.CINV+1
lda cx16.VERA_IEN
and #%11110000 ; disable all Vera IRQs
ora #%00000001 ; enable only the vsync Irq
sta cx16.VERA_IEN
cli
rts
_orig_irqvec .word 0
}}
}
asmsub set_rasterirq(uword handler @AY, uword rasterpos @R0) clobbers(A) {
%asm {{
sta _modified+1
sty _modified+2
lda cx16.r0
ldy cx16.r0+1
sei
lda cx16.VERA_IEN
and #%11110000 ; clear other IRQs
ora #%00000010 ; enable the line (raster) irq
sta cx16.VERA_IEN
lda cx16.r0
ldy cx16.r0+1
jsr set_rasterline
lda #<_raster_irq_handler
sta cx16.CINV
lda #>_raster_irq_handler
sta cx16.CINV+1
cli
rts
_raster_irq_handler
jsr set_irq._irq_handler_init
_modified jsr $ffff ; modified
jsr set_irq._irq_handler_end
; end irq processing - don't use kernal's irq handling
lda cx16.VERA_ISR
ora #%00000010
sta cx16.VERA_ISR ; clear Vera line irq status
ply
plx
pla
rti
}}
}
asmsub set_rasterline(uword line @AY) {
%asm {{
sta cx16.VERA_IRQ_LINE_L
lda cx16.VERA_IEN
and #%01111111
sta cx16.VERA_IEN
tya
lsr a
ror a
and #%10000000
ora cx16.VERA_IEN
sta cx16.VERA_IEN
rts
}}
}
}
sys {
; ------- lowlevel system routines --------
const ubyte target = 16 ; compilation target specifier. 64 = C64, 128 = C128, 16 = CommanderX16.
asmsub reset_system() {
; Soft-reset the system back to initial power-on Basic prompt.
%asm {{
sei
stz $01 ; bank the kernal in
jmp (cx16.RESET_VEC)
}}
}
asmsub wait(uword jiffies @AY) {
; --- wait approximately the given number of jiffies (1/60th seconds) (N or N+1)
; note: regular system vsync irq handler must be running, and no nother irqs
%asm {{
- wai ; wait for irq (assume it was vsync)
cmp #0
bne +
dey
+ dec a
bne -
cpy #0
bne -
rts
}}
}
inline asmsub waitvsync() {
; --- suspend execution until the next vsync has occurred, without depending on custom irq handling.
; note: system vsync irq handler has to be active for this routine to work (and no other irqs-- which is the default).
; note: a more accurate way to wait for vsync is to set up a vsync irq handler instead.
%asm {{
wai
}}
}
asmsub memcopy(uword source @R0, uword target @R1, uword count @AY) clobbers(A,X,Y) {
; note: can't be inlined because is called from asm as well
%asm {{
sta cx16.r2
sty cx16.r2+1
jmp cx16.memory_copy
}}
}
inline asmsub memset(uword mem @R0, uword numbytes @R1, ubyte value @A) clobbers(A,X,Y) {
%asm {{
jsr cx16.memory_fill
}}
}
asmsub memsetw(uword mem @R0, uword numwords @R1, uword value @AY) clobbers (A,X,Y) {
%asm {{
ldx cx16.r0
stx P8ZP_SCRATCH_W1
ldx cx16.r0+1
stx P8ZP_SCRATCH_W1+1
ldx cx16.r1
stx P8ZP_SCRATCH_W2
ldx cx16.r1+1
stx P8ZP_SCRATCH_W2+1
jmp prog8_lib.memsetw
}}
}
inline asmsub read_flags() -> ubyte @A {
%asm {{
php
pla
}}
}
inline asmsub clear_carry() {
%asm {{
clc
}}
}
inline asmsub set_carry() {
%asm {{
sec
}}
}
inline asmsub clear_irqd() {
%asm {{
cli
}}
}
inline asmsub set_irqd() {
%asm {{
sei
}}
}
inline asmsub exit(ubyte returnvalue @A) {
; -- immediately exit the program with a return code in the A register
%asm {{
jsr c64.CLRCHN ; reset i/o channels
ldx prog8_lib.orig_stackpointer
txs
rts ; return to original caller
}}
}
inline asmsub progend() -> uword @AY {
%asm {{
lda #<prog8_program_end
ldy #>prog8_program_end
}}
}
}