mirror of
https://github.com/AppleWin/AppleWin.git
synced 2024-11-19 19:33:03 +00:00
104 lines
3.5 KiB
Plaintext
104 lines
3.5 KiB
Plaintext
Key Super Serial Card (SSC) Memory Locations for Programmers
|
|
------------------------------------------------------------
|
|
|
|
All addresses are of the form '$C0sx', where 's' is the Slot number
|
|
of the SSC plus $8 and 'x' is the final digit ($0 - $F) of the
|
|
address.
|
|
|
|
Control Register
|
|
|
|
The 6551 Control Register is mapped to $C0sB
|
|
($C09B for Slot 1, $C0AB
|
|
for Slot 2, etc.).
|
|
Its format is ...
|
|
bit 7 : stop bit number [0= 1 stop bit, 1= 2 stop bits for most
|
|
settings, except: 1.5 stop bits for word length 5 and no parity,
|
|
and 1 for word length 8 and parity]
|
|
bits 6 and 5 : word length
|
|
[00= 8 bits, 01= 7 bits, 10= 6 bits, 11= 5 bits]
|
|
|
|
bit 4 : receiver clock source [0= external, 1= internal]
|
|
|
|
bits 3, 2, 1, 0 : baud rate, as follows:
|
|
0000= 16x external clock
|
|
0001= 50 bps
|
|
0010= 75 bps
|
|
0011= 109.92 bps
|
|
0100= 134.58 bps
|
|
0101= 150 bps
|
|
0110= 300 bps
|
|
0111= 600 bps
|
|
1000= 1200 bps
|
|
1001= 1800 bps
|
|
1010= 2400 bps
|
|
1011= 3600 bps
|
|
1100= 4800 bps
|
|
1101= 7200 bps
|
|
1110= 9600 bps
|
|
1111= 19200 bps
|
|
|
|
Note that 1 MHz Apples (everything other than the Apple IIgs and //c
|
|
Plus running in "fast" mode) cannot handle 19.2 kbps, and even 9600
|
|
bps on these machines requires either some highly optimised code or
|
|
a decent buffer in the device being accessed. The faster Apples
|
|
have no difficulty with this speed, however.
|
|
|
|
Command Register
|
|
|
|
The 6551 Command Register is mapped to $C0sA, and is essentially an
|
|
extension of the Control Register.
|
|
|
|
Its format is ...
|
|
bits 7 and 6 : parity mode control [00= odd parity, 01= even parity,
|
|
10= mark parity (parity bit always set),
|
|
11= space parity
|
|
(parity bit always cleared)]
|
|
|
|
bit 5 : parity mode enable [0=no parity used, 1=parity used]
|
|
bit 4 : receiver mode echo [0=no echo, 1=echo]
|
|
bits 3 and 2 : transmitter interrupt control
|
|
[00= set RTS high and transmit no interrupts,
|
|
01= set RTS low and transmit interrupts,
|
|
10= set RTS low and transmit no interrupts,
|
|
11= set RTS low and
|
|
transmit break signals instead of interrupts]
|
|
|
|
bit 1 : interrupt request disable
|
|
[0=enable receiver interrupts,
|
|
1=disable receiver interrupts]
|
|
bit 0 : Data Terminal Ready (DTR) setting
|
|
[0=set DTR high (indicates 'not ready'),
|
|
1=set DTR low (indicates 'ready')]
|
|
|
|
Note that, although the DTR is generally not used in the SSC
|
|
(it may actually not be connected!), it must be set to 'low' in order for the
|
|
6551 to function correctly. Also, the RTS signal must be set 'low'
|
|
in order to receive any incoming data from the serial device.
|
|
|
|
Note also that both the Command and Control registers are write-only,
|
|
which means that reading them will not necessarily yield valid data
|
|
on the device's settings. If there is any doubt as to the current
|
|
settings of the 6551, you should (re)initialise them.
|
|
|
|
Status register
|
|
|
|
The 6551 Status register is mapped to $C0s9. It is a read-only register
|
|
and its format is ...
|
|
|
|
bit 7 : interrupt [0=no interrupt, 1=interrupt]
|
|
bit 6 : Data Set Ready (DSR) [0=DSR low (ready), 1=DSR high (not ready)]
|
|
bit 5 : Data Carrier Detect (DCD) [0=DCD low (detected), 1=DCD high (not detected)]
|
|
bit 4 : transmitter data register empty [0=not empty, 1=empty]
|
|
bit 3 : receiver data register full [0=not full, 1=full]
|
|
bit 2 : overrun error [0=no error, 1=error]
|
|
bit 1 : framing error [0=no error, 1=error]
|
|
bit 0 : parity error [0=no error, 1=error]
|
|
|
|
Data Register
|
|
The Data Register at $C0s8 is used both for outgoing and incoming data.
|
|
Whether the data has been sent or received can be determined by checking
|
|
bits 4 and 3 (respectively) of the Status register.
|
|
|
|
I hope that this is the SSC programming information that you are looking for.
|
|
|
|
Aaron Heiss |