the arguments it consumed, which means the calling function encountered
them as well. As a result, a command like "ip -6 addr" was yielding a usage
error." - Philip Blundell
response sent in chunked transfer encoding, the code path to
resubmit the request to the redirected URL forgets to reset
got_clen and chunked variables in the loop. If the redirected
URL does not use chunked transfer encoding, this causes the code
that slurps the body of the response to incorrectly try to parse
out the chunk length which does not exist." - junkio@
----------------------------------------------------------------------
always told to read sizeof(buf). This waits until the underlying
fread() to time-out for the last part of the downloaded body. Fix
this by sending the number of remaining bytes to read when known." -
junkio@
I reworked the logic in his patch
The attached patch adds "mtu" and "hwaddress" to the inet6 method and
"mtu", "hwaddr" and "pointopoint" to the inet4 method (just like in
the ifupdown part).
Note: "hwaddress" can't be used with the busybox ip applet (this
function isn't implemented in bb ip yet), but it can be of use with
an external "full blown" ip package.
The patch also removes "label" from the loopback configuration,
labels (subinterfaces) aren't used with loopback interfaces.
It further solves a problem in the bootp method, "ifconfig down
%interface%" should be "ifconfig %interface% down" and it's now also
possible to use ip with bootp.
The patch is fully tested with both busybox ip and "stand-alone" ip
and I didn't saw any problems.
The recent changes in ifupdown where all calls to 'ip link set' and
'ip addr set' are swapped give some problems with v4tunnels.
For plain ipv4 and ipv6 interfaces it works correct, other methods
not tried. The patch below change the behaviour back for v4tunnels
only.
Without the patch the following errors are shown:
RTNETLINK answers: Network is down
RTNETLINK answers: No route to host
and the tunnel is not fully brought up
With this patch all works as expected.
this patch fixes run_parts when it's called by ifupdown. 1) argv has to be a
NULL terminated char* array, not just a string. 2) run_parts now explicitly
sets the environment. this environment is populated from the
/etc/network/interfaces config file and is needed by the scripts in
/etc/network/if-pre-up.d/. when run-parts is called from the command line the
environment is taken from the current process.
Vladimir Oleynik then wrote:
You can simplify this if use:
+ bb_xasprintf(&buf[0], "/etc/network/if-%s.d", opt);
+ buf[1] = NULL;
+
+ run_parts(&buf, 2, environ);
+ free(buf[0]);
--w
vodz
Hi.
Last patch have new libbb function
vfork_rexec() for can use daemon() to uClinux system.
This patched daemons: syslog, klogd, inetd, crond.
This not tested! I havn`t this systems.
Also. Previous patch for feature request MD5 crypt password for
httpd don`t sended to this mailist on 07/15/03
(mailist have Pytom module problem?).
The previous patch included, and have testing.
--w
vodz
Hello all,
This patch adds more "Help" text to the config system. Almost
all applets now have a help entry. Also, I cleaned up the spacing of
the existing text so that things are consistent. This patch is against
this morning's CVS.
Thomas Cameron
CEI Systems, Inc.
This patch fixes endian problems with get_netmask(). I don't know if
this is the cleanest solution, but it makes 'ipcalc -n' work on both
an i386 system and a ppc system.
Erik, et al.
The attached patch makes the following changes to networking/ifupdown.c:
(1) It swaps all calls to 'ip link set' and 'ip addr set'. This solves
two problems:
(a) Calling 'ip link set <dev> up' before assigning an address
generates an error message, and
(b) Under User Mode Linux, running in with ethernet interfaces
in daemon mode, the MAC address for an interface is selected
based on the IP address assigned to that interface. If the
interface is brought up before being assigned an IP address,
it gets a null MAC.
(2) It further cleans up run_mapping().
This patch is against ifupdown.c revision 1.25.
-- Lars
Hello, I think the test for an unconfigured httpd is wrong in
the CVS (busybox-unstable-20030620.tar.bz2)
flg_deny_all is default 0
vodz then wrote:
Oops. You are right.
Also, this mistake haved from two place.
Last patch rewroted to my new get_ularg() function for overcompensate size
from this error found ;-)
I'm building BusyBox using a development kit for MontaVista Hardhat Linux
(PPC) -- which, at least in this instance, is based around kernel 2.2.14.
I've had to massage a few files in networking/libiproute/ to make it
compile. Specifically:
(1) Added a #include <sys/uio.h> for the iovec structure in
libnetlink.c,
(2) Put ifdefs in ll_types.c and ll_proto.c around various
constants (ETH_P_xxx and ARPHRD_xxx) that weren't defined,
(3) Make do_changename() in iplink.c require a kernel >=
2.4.0 -- the ifr structure in my environment doesn't
have the ifr_name attribute. I've assumed this is
a kernel dependency -- let me know if I ought to be
checking something else.
In the absence of the correct kernel, do_changename()
always returns 0.
Attached is a patch against the current CVS that will make these changes.
-- Lars
The attached patch fixes a compilation error. If you compile ping6 without
the CONFIG_FEATURE_FANCY_PING6 option then the compile will fail without this
patch.
- more comments
- larger allowed number of CGI script variables
- ifdefs for regression test hooks
- default to ./ rather than /www (if unspecified) for compatibility with
earlier versions.
- Allow ip: as a synomym for A: rules for compatibility with earlier
versions.
- Setting of CGI_ARGLIST_ when automatic setting of env vars for form
scripting is utilized. This helps with minimal systems like openap.
