Stuff to put a FPGA in a NuBus Macintosh
Go to file
2023-05-08 15:55:54 +02:00
nubus-to-ztex more Silk 2023-04-04 22:40:58 +02:00
nubus-to-ztex-gateware more comments 2023-05-08 15:55:54 +02:00
Pictures pictures 2023-04-24 08:22:32 +02:00
.gitignore accel in 16/32 ; includes adding MUL to Vex & fixing a FIFO overrun in NuBus in 32 bits mode 2022-06-04 14:55:40 +02:00
.gitmodules submodule for HDMI-Alt 2023-01-08 15:30:56 +01:00
README.md better qemu support, exp. add of Eth 2023-04-16 09:04:21 +02:00

A FPGA on a NuBus card...

Goal

The goal of this repository is to be able to interface a modern (2021 era) FPGA with a NuBus host, specifically Apple's Macintosh II and Macintosh Quadra. NuBus was widely used by Apple and a little by others (such as NeXT), but was progressively displaced by PCI from the mid-90s onward, and is thoroughly obsolete.

So unless you're a retrocomputing enthusiast with such a machine, this is useless. If you are such an enthusiast, then maybe the ability to connect a modern LCD monitor using a digital interface to an old Macintosh might be of interest to you.

This project was 'spun off' the SBusFPGA, a similar project for the SBus used in Sun's SPARCstation.

Current status

First prototype is working in a Quadra 650, running MacOS 8.1. It implements a single-screen-resolution, windowboxed multi-resolution, depth-switchable (1/2/4/8/16/32 bits) framebuffer over DVI-in-HDMI-connector (will work with any HDMI-compliant monitor). The framebuffer can be used as secondary/primary/only framebuffer in the machine running OS8.1. Qemu tests indicate this should work with 7.1 & 7.5/7.6 as well. An alternate HDMI PHY also supports audio, enabled as a 8/16 bits, mono/stereo, 44.1 kHz output component in MacOS.

Some basic acceleration now exists for 8/16/32 bits, doing rectangle screen-to-screen blits and pattern rectangle fills. 1/2/4 bits also has some acceleration, but only for byte-aligned cases.

There's also a basic RAM Disk using the 248 MiB of SDRAM not used by the framebuffer. The driver can use either synchronous direct access to the memory bt the CPU, or asynchronous using DMA (using 16-bytes blocks). Frustratingly, the direct access methode seems faster.

The hardware

Directory 'nubus-to-ztex'

The V1.0 custom board is a NuBus-compliant (I hope...) board, designed to receive a ZTex USB-FPGA Module 2.13 as a daughterboard. The ZTex module contains the actual FPGA (Artix-7), some RAM, programming hardware, etc. The NuBus board contains level-shifters & drivers ICs to interface between the NuBus signals and the FPGA, a CPLD handling some level-shifting & the bus mastering arbitration, a serial header, two user Leds, 14 debug Leds tied to specific NuBus or CPLD/FPGA signals, a JTAG header, a USB micro-B connector, a VGA chip & connector, and a HDMI chip & connector. It supports every NuBus feature except the optional parity (i.e. it can do both slave and master modes).

The V1.0 board is in commit 3f3371a. The CPLD solution works but is annoying as it requires older Xilinx software (ISE 14.7) and dedicated JTAG programmer to use. A revision V1.2 board is in the work but not yet made, which will remove the VGA connector and CPLD (and require more dedicated level-shifters/drivers) and replace them by a micro-sd card slot and an expansion connector (Pmod-like).

The PCB was designed with Kicad 5.0

The gateware (Migen)

Directory 'sbus-to-ztex-gateware'

The gateware is written in the Migen language, choosen because that's what Litex uses. It implements a simple CPU-less Litex SoC built around a Wishbone bus, with a custom bridge between the NuBus and the Wishbone.

A Declaration ROM, a SDRAM controller (litedram to the on-board DDR3), and the 'Goblin' multi-depth framebuffer can be connected to that bus. Other devices could be added, see the SBusFPGA or the Common directory, but the software support is missing; vintage System 7/MacOS 8 are not as welcoming to new devices as modern NetBSD. Theoretically, quite a bit of code originally written to support the SBusFPGA in NetBSD/sparc could be reused for similar devices in NetBSD/mac68k, but it has not happened yet.

The SDRAM has its own custom DMA controller, using native Litedram interface to the memory, and some FIFO to/from the NuBus. A custom MacOS driver exposes it as a volatile drive. Driver can use synchronous direct accesses from the CPU (using the NuBus's superslot area), or asynchronous (interrupt-driven) DMA transfers using NuBus 1x block transfers.

The software

The Declaration ROM is in the subdirectory DeclROM and includes the driver needed for the unaccelerated framebuffer and the RAM Disk. It needs the Retro68 toolchain to build.

The code for the NuBusFPGAInit (which should be renamed) is in NuBusFPGAInit/, and will need a CodeWarrior INIT project to build, on a real Macintosh or an emulated one using e.g. Qemu. It enables graphic acceleration.