Allow VRAM presence only in optional bank.
control: Implement banks.
The BAR is 64MB.
The little-endian/big-endian ranges repeat every 16MB.
An endian range can be addressed in d128 (wide) mode or d64 mode.
In d128 mode, there is a 4MB range followed by an undefined 4MB range. bytes 0..7 belong to the standard bank and bytes 8..15 belong to the optional bank.
In d64 mode:
- 2MB mirror ranges at 0MB and 2MB (both have the same read/write behavor: write to both banks or read from the standard bank.
- 2MB standard bank rage at 4MB.
- 2MB optional bank range at 6MB.
bytes_out is used instead of the removed cur_buf_cnt.
data_ptr is setup by prepare_data instead of process_command.
Not sure why scsicdrom doesn't set bytes_out in prepare_data.
- Use macros for reading 2 byte or 4 byte big endian data. block_size is assumed to be < 64K so WRITE_DWORD_BE_A will write two leading zeros.
- Scalar pass by value parameters don't need to be const.
- Remove some unnecessary locals.
Make it a separate method like scsihd. It also checks the incoming param size. If it's zero then the phase is not switched. Is that wrong? Still probably unfinished.
The total size needs to have 3 factors cylinders, heads, & sectors. Imagine a disk having a total size with 3 prime factors 3 x 5 x 11. 15 cannot be assigned to heads because that would only leave 11 for sectors and cylinders. Therefore, test all heads and sectors combinations. If the third factor for cylinders is not found, then choose 16 heads, then the minimum number of sectors, and finally the maximum number of cylinders. The loop could be changed to skip values of heads that are not a factor, but it doesn't take any time to try them all.
In Xcode, type Command-Shift-B to analyze every source file or Command-Shift-Control-B to analyze the current source file.
For pseudo_dma_read report FIFO underrun and init data_word in that case.
- Read 8 bytes at a time instead of just 1.
- Remove multiply operations from loop. We just need increments or additions.
- Change compares with int to compares with zero.
CUR_HORZ_OFF becomes non-zero when the cursor needs to be drawn to the left of the left edge of the frame buffer.
CUR_VERT_OFF is handled differently. When CUR_VERT_OFF is non-zero, CUR_OFFSET is changed to point to the first line of the cursor that will be drawn, so CUR_VERT_OFF is the number of lines to remove from the total height of the cursor.
Alternatively, we could handle CUR_VERT_OFF the same way as CUR_HORZ_OFF by leaving the cursor height constant, drawing the cursor starting from the CUR_VERT_OFF line, and adjusting cursor Y position by negative CUR_VERT_OFF.
- Read 8 bytes at a time instead of just 1.
- Remove multiply operations from loop. We just need increments or additions.
- Change compares with int to compares with zero.
CUR_HORZ_OFF becomes non-zero when the cursor needs to be drawn to the left of the left edge of the frame buffer.
CUR_VERT_OFF is handled differently. When CUR_VERT_OFF is non-zero, CUR_OFFSET is changed to point to the first line of the cursor that will be drawn, so CUR_VERT_OFF is the number of lines to remove from the total height of the cursor.
Alternatively, we could handle CUR_VERT_OFF the same way as CUR_HORZ_OFF by leaving the cursor height constant, drawing the cursor starting from the CUR_VERT_OFF line, and adjusting cursor Y position by negative CUR_VERT_OFF.
scsibus has a new method attach_scsi_devices which is used by all machines to populate a SCSI bus with one or more hard drives or CD-ROM drives.
HDDs are specified by the hdd_img property.
CDs are specified by the cdr_img property.
Multiple images are delimited by a colon :
attach_scsi_devices is called by the scsi controller after the scsi controller has attached itself to the scsi bus.
The bus suffix is applied to the property name.
Curio has no suffix so it will use hdd_img and cdr_img properties.
Mesh is expected to have a suffix of 2 so it will use hdd_img2 and cdr_img2 properties.
HDDs will skip SCSI ID 3 unless 7 HDDs are added, in which case, the seventh HDD will use ID 3.
CDs will start at SCSI ID 3, go to 7, then down to 0.
SCSI IDs are skipped if a device is already using that SCSI ID.
ScsiCdrom and ScsiHD no longer use REGISTER_DEVICE or DeviceDescription or PropMap which is normal for devices that can have multiple instances.
This method is used by both pci_io_read and pci_io_write to determine if ISA type I/O access is allowed.
The SPARSE_IO_BASE I/O address is defined. This I/O range is not defined by an I/O BAR.
- Add IOBusDevice (nvram_addr_hi_dev) for NVRAM addr hi.
- Add IOBusDevice (nvram_dev) for NVRAM data.
- Make all IOBusDevices use the same code.
- Log error if 4 least significant bits of offset are not zero.
- Correctly byte swap the value before passing it to the IOBusDevice.
- When reading, duplicate the bytes in a word or dword like a real Power Mac does.
Grackle allows attaching different PCI devices. This change allows attach multiple of the same PCI device. To make the name unique in the machine map, the name of the PCI slot is appended to the device name.
There are cases where when it's necessary (e.g. given uninitialized NVRAM,
the Beige G3 with the 10.2 install CD inserted will update the boot
device and restart to boot from it).
Restart support was done by wrapping the ppc_exec function in a loop and
checking for a restart power off reason. We also need to disconnect all
event listeners, since they will be recreated when the machine is
re-initialized.
