Last step of CMD_COMPLETE_STEPS includes INTSTAT_SO to indicate to CurioSCSIController::fsmCompleting that it returned both a status byte and a message byte in the FIFO.
- For pdm/amic, real_dma_xfer is called when SCSI_DMA_Ctrl has the run bit set.
- For tnt/grandcentral, dma_wait is called when the DBDMA is started (run bit is set). It will call real_dma_xfer when the phase and sequence are DATA_IN/RCV_DATA or DATA_OUT/SEND_DATA.
- dma_wait and real_dma_xfer uses a one shot timer instead of a loop to continue doing DMA while also giving time to the CPU. This and the above changes handles the case where the DBDMA is started before setting up the transfer phase and sequence.
- dma_stop will stop the one shot timer when the DBDMA channel is stopped.
bytes_out is used instead of the removed cur_buf_cnt.
data_ptr is setup by prepare_data instead of process_command.
Not sure why scsicdrom doesn't set bytes_out in prepare_data.
- Use macros for reading 2 byte or 4 byte big endian data. block_size is assumed to be < 64K so WRITE_DWORD_BE_A will write two leading zeros.
- Scalar pass by value parameters don't need to be const.
- Remove some unnecessary locals.
Make it a separate method like scsihd. It also checks the incoming param size. If it's zero then the phase is not switched. Is that wrong? Still probably unfinished.
The total size needs to have 3 factors cylinders, heads, & sectors. Imagine a disk having a total size with 3 prime factors 3 x 5 x 11. 15 cannot be assigned to heads because that would only leave 11 for sectors and cylinders. Therefore, test all heads and sectors combinations. If the third factor for cylinders is not found, then choose 16 heads, then the minimum number of sectors, and finally the maximum number of cylinders. The loop could be changed to skip values of heads that are not a factor, but it doesn't take any time to try them all.
In Xcode, type Command-Shift-B to analyze every source file or Command-Shift-Control-B to analyze the current source file.
For pseudo_dma_read report FIFO underrun and init data_word in that case.
scsibus has a new method attach_scsi_devices which is used by all machines to populate a SCSI bus with one or more hard drives or CD-ROM drives.
HDDs are specified by the hdd_img property.
CDs are specified by the cdr_img property.
Multiple images are delimited by a colon :
attach_scsi_devices is called by the scsi controller after the scsi controller has attached itself to the scsi bus.
The bus suffix is applied to the property name.
Curio has no suffix so it will use hdd_img and cdr_img properties.
Mesh is expected to have a suffix of 2 so it will use hdd_img2 and cdr_img2 properties.
HDDs will skip SCSI ID 3 unless 7 HDDs are added, in which case, the seventh HDD will use ID 3.
CDs will start at SCSI ID 3, go to 7, then down to 0.
SCSI IDs are skipped if a device is already using that SCSI ID.
ScsiCdrom and ScsiHD no longer use REGISTER_DEVICE or DeviceDescription or PropMap which is normal for devices that can have multiple instances.
There are cases where when it's necessary (e.g. given uninitialized NVRAM,
the Beige G3 with the 10.2 install CD inserted will update the boot
device and restart to boot from it).
Restart support was done by wrapping the ppc_exec function in a loop and
checking for a restart power off reason. We also need to disconnect all
event listeners, since they will be recreated when the machine is
re-initialized.
When fetching DMA command, make sure to convert little endian fields to host endianness (i.e. don't use memcpy).
When fetching DMA command, return the host address of the DMA command for LOAD_QUAD. Maybe this address should be cached whenever this->cmdptr changes?
When fetching DMA command, return whether the DMA command is writable.
For LOAD_QUAD, pass the address of the DMA command to xfer_quad.
Always log unexpected DMA command values.
Write full 32-bit value for LOAD_QUAD.
Write reqCount to resCount.
pci_conv_rd_data can be used to handle unaligned or 64-bit accesses in mmio regions if it's modified to include the next 32-bit value.
For pci config accesses, grackle repeats the 32-bit value. bandit uses a seemingly random number for the next 32-bit value, but we'll make it work like grackle.
PCCard is used by PowerBook G3 Wallstreet in Open Firmware 2.0.1.
CardBus is probed in New World Macs starting from at least Open Firmware 4.1.9f1 sometime after Open Firmware 3.1.1.
- Create PCIBase from common stuff in PCIDevice.
- Add PCIBridgeBase. These have a primary bus number, secondary bus number, and subordinate bus number which are used to determine if PCI type 1 config cycle should be passed.
- Change PCIBridge to use PCIBridgeBase instead of PCIDevice.
- Add PCICardBusBridge which uses PCIBridgeBase.
For example, Old World Macs have versions of Open Firmware that don't support 512 MB BARs correctly. They may attempt to set such a BAR to 0x90000000 (a 256 MB boundary) instead of 0xA0000000 (the next available 512 MB boundary).
So that you don't see identical messages "Could not restore NVRAM content from the given file."
Instead, one will mention nvram.bin and the other will mention pram.bin.
