mirror of
https://github.com/TomHarte/CLK.git
synced 2024-11-25 16:31:42 +00:00
139 lines
3.3 KiB
C++
139 lines
3.3 KiB
C++
//
|
|
// i8272.hpp
|
|
// Clock Signal
|
|
//
|
|
// Created by Thomas Harte on 05/08/2017.
|
|
// Copyright 2017 Thomas Harte. All rights reserved.
|
|
//
|
|
|
|
#ifndef i8272_hpp
|
|
#define i8272_hpp
|
|
|
|
#include "CommandDecoder.hpp"
|
|
#include "Status.hpp"
|
|
|
|
#include "../../Storage/Disk/Controller/MFMDiskController.hpp"
|
|
|
|
#include <cstdint>
|
|
#include <memory>
|
|
#include <vector>
|
|
|
|
namespace Intel::i8272 {
|
|
|
|
class BusHandler {
|
|
public:
|
|
virtual ~BusHandler() {}
|
|
virtual void set_dma_data_request([[maybe_unused]] bool drq) {}
|
|
virtual void set_interrupt([[maybe_unused]] bool irq) {}
|
|
};
|
|
|
|
class i8272 : public Storage::Disk::MFMController {
|
|
public:
|
|
i8272(BusHandler &bus_handler, Cycles clock_rate);
|
|
|
|
void run_for(Cycles);
|
|
|
|
void set_data_input(uint8_t value);
|
|
uint8_t get_data_output();
|
|
|
|
void write(int address, uint8_t value);
|
|
uint8_t read(int address);
|
|
|
|
void set_dma_acknowledge(bool dack);
|
|
void set_terminal_count(bool tc);
|
|
|
|
ClockingHint::Preference preferred_clocking() const final;
|
|
|
|
protected:
|
|
virtual void select_drive(int number) = 0;
|
|
|
|
private:
|
|
// The bus handler, for interrupt and DMA-driven usage. [TODO]
|
|
BusHandler &bus_handler_;
|
|
std::unique_ptr<BusHandler> allocated_bus_handler_;
|
|
|
|
// Status registers.
|
|
Status status_;
|
|
|
|
// The incoming command.
|
|
CommandDecoder command_;
|
|
|
|
// A buffer to accumulate the result.
|
|
std::vector<uint8_t> result_stack_;
|
|
uint8_t input_ = 0;
|
|
bool has_input_ = false;
|
|
bool expects_input_ = false;
|
|
|
|
// Event stream: the 8272-specific events, plus the current event state.
|
|
enum class Event8272: int {
|
|
CommandByte = (1 << 3),
|
|
Timer = (1 << 4),
|
|
ResultEmpty = (1 << 5),
|
|
NoLongerReady = (1 << 6)
|
|
};
|
|
void posit_event(int type) final;
|
|
int interesting_event_mask_ = int(Event8272::CommandByte);
|
|
int resume_point_ = 0;
|
|
bool is_access_command_ = false;
|
|
|
|
// The counter used for ::Timer events.
|
|
Cycles::IntType delay_time_ = 0;
|
|
|
|
// The connected drives.
|
|
struct Drive {
|
|
uint8_t head_position = 0;
|
|
|
|
// Seeking: persistent state.
|
|
enum Phase {
|
|
NotSeeking,
|
|
Seeking,
|
|
CompletedSeeking
|
|
} phase = NotSeeking;
|
|
bool did_seek = false;
|
|
bool seek_failed = false;
|
|
|
|
// Seeking: transient state.
|
|
Cycles::IntType step_rate_counter = 0;
|
|
int steps_taken = 0;
|
|
int target_head_position = 0; // either an actual number, or -1 to indicate to step until track zero
|
|
|
|
// Head state.
|
|
Cycles::IntType head_unload_delay[2] = {0, 0};
|
|
bool head_is_loaded[2] = {false, false};
|
|
|
|
} drives_[4];
|
|
int drives_seeking_ = 0;
|
|
|
|
/// @returns @c true if the selected drive, which is number @c drive, can stop seeking.
|
|
bool seek_is_satisfied(int drive);
|
|
|
|
// User-supplied parameters; as per the specify command.
|
|
int step_rate_time_ = 1;
|
|
int head_unload_time_ = 1;
|
|
int head_load_time_ = 1;
|
|
bool dma_mode_ = false;
|
|
bool is_executing_ = false;
|
|
|
|
// A count of head unload timers currently running.
|
|
int head_timers_running_ = 0;
|
|
|
|
// Transient storage and counters used while reading the disk.
|
|
uint8_t header_[6] = {0, 0, 0, 0, 0, 0};
|
|
int distance_into_section_ = 0;
|
|
int index_hole_count_ = 0, index_hole_limit_ = 0;
|
|
|
|
// Keeps track of the drive and head in use during commands.
|
|
int active_drive_ = 0;
|
|
int active_head_ = 0;
|
|
|
|
// Internal registers.
|
|
uint8_t cylinder_ = 0, head_ = 0, sector_ = 0, size_ = 0;
|
|
|
|
// Master switch on not performing any work.
|
|
bool is_sleeping_ = false;
|
|
};
|
|
|
|
}
|
|
|
|
#endif /* i8272_hpp */
|