mirror of
https://github.com/uffejakobsen/acme.git
synced 2024-12-13 03:29:55 +00:00
bc68e36127
git-svn-id: https://svn.code.sf.net/p/acme-crossass/code-0/trunk@98 4df02467-bbd4-4a76-a152-e7ce94205b78
161 lines
7.3 KiB
Plaintext
161 lines
7.3 KiB
Plaintext
;ACME 0.95
|
|
|
|
!ifdef lib_cbm_c128_mmu_a !eof
|
|
lib_cbm_c128_mmu_a = 2
|
|
|
|
; Memory Management Unit (MMU) 8722
|
|
|
|
|
|
; registers in i/o area (i/o needs to be enabled to access these):
|
|
|
|
!address {
|
|
; configuration register
|
|
mmu_cr_d500 = $d500 ; same as "mmu_cr" at $ff00. Use "mmu_cr" instead, as that is *always* available.
|
|
; preconfiguration registers (internal format just like mmu_cr)
|
|
mmu_pcr_a = $d501 ; c128 kernal default is $3f (BANK 0)
|
|
mmu_pcr_b = $d502 ; c128 kernal default is $7f (BANK 1)
|
|
mmu_pcr_c = $d503 ; c128 kernal default is $01 (BANK 14)
|
|
mmu_pcr_d = $d504 ; c128 kernal default is $41 (all system roms, with ram 1)
|
|
}
|
|
; contents of cr and all four pcr:
|
|
mmu_CR_RAMBANK_MASK = %##...... ; this controls which RAM bank is used in areas where RAM is enabled
|
|
;mmu_CR_RAMBANK_0 = %........
|
|
mmu_CR_RAMBANK_1 = %.#......
|
|
mmu_CR_RAMBANK_2 = %#....... ; on an unmodified c128, there is no ram bank 2 (0 will be used instead)
|
|
mmu_CR_RAMBANK_3 = %##...... ; on an unmodified c128, there is no ram bank 3 (1 will be used instead)
|
|
|
|
mmu_CR_HIGH_MASK = %..##.... ; this controls the "high area" (c000..ffff), but i/o (d000..dfff) is separate
|
|
;mmu_CR_HIGH_SYSROM = %........ ; editor, charset (or i/o, see below), kernal
|
|
mmu_CR_HIGH_INTFUNCROM = %...#....
|
|
mmu_CR_HIGH_EXTFUNCROM = %..#.....
|
|
mmu_CR_HIGH_RAM = %..##....
|
|
|
|
mmu_CR_MID_MASK = %....##.. ; this controls the "middle area" (8000..bfff)
|
|
;mmu_CR_MID_SYSROM = %........ ; this is the upper half of basic
|
|
mmu_CR_MID_INTFUNCROM = %.....#..
|
|
mmu_CR_MID_EXTFUNCROM = %....#...
|
|
mmu_CR_MID_RAM = %....##..
|
|
|
|
mmu_CR_LOW_MASK = %......#. ; this controls the "low area" (4000..7fff)
|
|
;mmu_CR_LOW_SYSROM = %........ ; this is the lower half of basic
|
|
mmu_CR_LOW_RAM = %......#.
|
|
|
|
mmu_CR_IO_MASK = %.......# ; this controls i/o space (d000..dfff)
|
|
;mmu_CR_IO_ON = %........
|
|
mmu_CR_IO_OFF = %.......# ; if i/o is off, contents depend on "high area"
|
|
|
|
; configuration register values used by C128 firmware (lookup table at $f7f0, see end of file):
|
|
mmu_CR_BANK0 = $3f ; full 64 KiB ram bank 0
|
|
mmu_CR_BANK1 = $7f ; full 64 KiB ram bank 1
|
|
mmu_CR_BANK2 = $bf ; full 64 KiB ram bank 2
|
|
mmu_CR_BANK3 = $ff ; full 64 KiB ram bank 3
|
|
mmu_CR_BANK4 = $16 ; 32 KiB bank 0; 32 KiB IFROM with i/o overlay
|
|
mmu_CR_BANK5 = $56 ; 32 KiB bank 1; 32 KiB IFROM with i/o overlay
|
|
mmu_CR_BANK6 = $96 ; 32 KiB bank 2; 32 KiB IFROM with i/o overlay
|
|
mmu_CR_BANK7 = $d6 ; 32 KiB bank 3; 32 KiB IFROM with i/o overlay
|
|
mmu_CR_BANK8 = $2a ; 32 KiB bank 0; 32 KiB EFROM with i/o overlay
|
|
mmu_CR_BANK9 = $6a ; 32 KiB bank 1; 32 KiB EFROM with i/o overlay
|
|
mmu_CR_BANK10 = $aa ; 32 KiB bank 2; 32 KiB EFROM with i/o overlay
|
|
mmu_CR_BANK11 = $ea ; 32 KiB bank 3; 32 KiB EFROM with i/o overlay
|
|
mmu_CR_BANK12 = $06 ; 32 KiB bank 0; 16 KiB IFROM; 16 KiB kernal with i/o overlay
|
|
mmu_CR_BANK13 = $0a ; 32 KiB bank 0; 16 KiB EFROM; 16 KiB kernal with i/o overlay
|
|
mmu_CR_BANK14 = $01 ; 16 KiB bank 0; 32 KiB basic; 16 KiB kernal with font overlay
|
|
mmu_CR_BANK15 = $00 ; 16 KiB bank 0; 32 KiB basic; 16 KiB kernal with i/o overlay
|
|
; An unmodified C128 does not have a "ram bank 2" or "ram bank 3".
|
|
; Whenever one of these is activated, ram banks 0 and 1 will be used instead.
|
|
; IFROM means internal function ROM (socket U36)
|
|
; EFROM means external function ROM (socket in a REU, for example)
|
|
|
|
!address {
|
|
; mode configuration register
|
|
mmu_mcr = $d505
|
|
}
|
|
; contents:
|
|
mmu_MCR_40COLUMNS = %#....... ; (pin 48) 40/80 key: 0 means pressed, 1 means released (writable! if cleared, will always read as 0!)
|
|
mmu_MCR_C64MODE = %.#...... ; (pin 47) setting this bit makes the MMU disappear from the memory map :)
|
|
mmu_MCR_EXROM = %..#..... ; (pin 46) if zero on boot, system will enter c64 mode (writable!)
|
|
mmu_MCR_GAME = %...#.... ; (pin 45) if zero on boot, system will enter c64 mode (writable!)
|
|
mmu_MCR_FSDIR_OUTPUT = %....#... ; (pin 44) direction of fast serial bus
|
|
mmu_MCR_UNUSED = %.....##. ; always set
|
|
mmu_MCR_8502MODE = %.......# ; (pin 43 inverted) setting this to zero switches to Z80 cpu
|
|
|
|
!address {
|
|
; ram configuration register
|
|
mmu_rcr = $d506
|
|
}
|
|
; contents:
|
|
mmu_RCR_VICBANK_MASK = %##...... ; this controls which RAM bank is "seen" by VIC
|
|
;mmu_RCR_VICBANK_0 = %........
|
|
mmu_RCR_VICBANK_1 = %.#......
|
|
mmu_RCR_VICBANK_2 = %#....... ; on an unmodified c128, there is no ram bank 2 (0 will be used instead)
|
|
mmu_RCR_VICBANK_3 = %##...... ; on an unmodified c128, there is no ram bank 3 (1 will be used instead)
|
|
|
|
mmu_RCR_RAMBLOCK_MASK = %..##.... ; on an unmodified c128, these bits are irrelevant (they select 256 KiB of 1 MiB of memory)
|
|
;mmu_RCR_RAMBLOCK_0 = %........
|
|
mmu_RCR_RAMBLOCK_1 = %...#.... ; on an unmodified c128, there is only ram block 0
|
|
mmu_RCR_RAMBLOCK_2 = %..#..... ; on an unmodified c128, there is only ram block 0
|
|
mmu_RCR_RAMBLOCK_3 = %..##.... ; on an unmodified c128, there is only ram block 0
|
|
|
|
mmu_RCR_SHARE_MASK = %....##..
|
|
;mmu_RCR_SHARE_NONE = %........
|
|
mmu_RCR_SHARE_BOTTOM = %.....#.. ; system default
|
|
mmu_RCR_SHARE_TOP = %....#...
|
|
|
|
mmu_RCR_SHARESIZE_MASK = %......##
|
|
;mmu_RCR_SHARESIZE_1K = %........ ; system default
|
|
mmu_RCR_SHARESIZE_4K = %.......#
|
|
mmu_RCR_SHARESIZE_8K = %......#.
|
|
mmu_RCR_SHARESIZE_16K = %......##
|
|
|
|
!address {
|
|
; page pointers for zero page and stack:
|
|
; write to "bank" register will be latched (reading gives old value)
|
|
; until "page" register is written to as well.
|
|
mmu_zp_page = $d507 ; address bits a8..a15, default $00
|
|
mmu_zp_bank = $d508 ; address bits a16..a19, default $0 (on an unmodified c128, only bit0 is meaningful)
|
|
mmu_stack_page = $d509 ; address bits a8..a15, default $01
|
|
mmu_stack_bank = $d50a ; address bits a16..a19, default $0 (on an unmodified c128, only bit0 is meaningful)
|
|
}
|
|
mmu_PxH_UNUSED = %####.... ; always set
|
|
|
|
mmu_PxH_RAMBLOCK_MASK = %....##..
|
|
;mmu_PxH_RAMBLOCK_0 = %........
|
|
mmu_PxH_RAMBLOCK_1 = %.....#.. ; on an unmodified c128, there is only ram block 0
|
|
mmu_PxH_RAMBLOCK_2 = %....#... ; on an unmodified c128, there is only ram block 0
|
|
mmu_PxH_RAMBLOCK_3 = %....##.. ; on an unmodified c128, there is only ram block 0
|
|
|
|
mmu_PxH_RAMBANK_MASK = %......##
|
|
;mmu_PxH_RAMBANK_0 = %........
|
|
mmu_PxH_RAMBANK_1 = %.......#
|
|
mmu_PxH_RAMBANK_2 = %......#. ; on an unmodified c128, there is no ram bank 2 (0 will be used instead)
|
|
mmu_PxH_RAMBANK_3 = %......## ; on an unmodified c128, there is no ram bank 3 (1 will be used instead)
|
|
|
|
!address {
|
|
; version register
|
|
mmu_vr = $d50b ; read-only, value is $20
|
|
}
|
|
mmu_VR_BANKS_MASK = %####.... ; 2 ram banks
|
|
mmu_VR_VERSION_MASK = %....#### ; mmu version 0
|
|
|
|
; reading addresses up until $d5ff returns $ff
|
|
|
|
|
|
; these registers are always available (in *every* memory configuration) unless C64 mode is entered:
|
|
|
|
!address {
|
|
; configuration register
|
|
mmu_cr = $ff00 ; always use this instead of $d500
|
|
; load configuration registers:
|
|
; a read access will return the value of the corresponding preconfiguration register
|
|
; any write access will copy the value of the corresponding preconfiguration register to mmu_cr
|
|
mmu_lcr_a = $ff01 ; c128 kernal default is $3f (BANK 0)
|
|
mmu_lcr_b = $ff02 ; c128 kernal default is $7f (BANK 1)
|
|
mmu_lcr_c = $ff03 ; c128 kernal default is $01 (BANK 14)
|
|
mmu_lcr_d = $ff04 ; c128 kernal default is $41 (all system roms, with ram 1)
|
|
|
|
; the c128 ROMs contain a look-up table to convert bank numbers to their
|
|
; corresponding configuration register values:
|
|
; romc_* needs "high rom area" enabled ($c000..$ffff)
|
|
romc_bank_to_cr_table = $f7f0 ; 3f 7f bf ff 16 56 96 d6 2a 6a aa ea 06 0a 01 00
|
|
}
|