Summary:
Correct the match patterns and the lowerings that made the CodeGen tests pass despite the mistakes.
The original testcase that discovered the problem was SingleSource/UnitTests/SignlessType/factor.c in test-suite.
During review, we also found that some of the existing CodeGen tests were incorrect and fixed them:
* bitwise.ll: In bsel_v16i8 the IfSet/IfClear were reversed because bsel and bmnz have different operand orders and the test didn't correctly account for this. bmnz goes 'IfClear, IfSet, CondMask', while bsel goes 'CondMask, IfClear, IfSet'.
* vec.ll: In the cases where a bsel is emitted as a bmnz (they are the same operation with a different input tied to the result) the operands were in the wrong order.
* compare.ll and compare_float.ll: The bsel operand order was correct for a greater-than comparison, but a greater-than comparison instruction doesn't exist. Lowering this operation inverts the condition so the IfSet/IfClear need to be swapped to match.
The differences between BSEL, BMNZ, and BMZ and how they map to/from vselect are rather confusing. I've therefore added a note to MSA.txt to explain this in a single place in addition to the comments that explain each case.
Reviewers: matheusalmeida, jacksprat
Reviewed By: matheusalmeida
Differential Revision: http://llvm-reviews.chandlerc.com/D3028
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203657 91177308-0d34-0410-b5e6-96231b3b80d8
When the list of VFP registers to be saved was non-contiguous (so multiple
vpush/vpop instructions were needed) these were being ordered oddly, as in:
vpush {d8, d9}
vpush {d11}
This led to the layout in memory being [d11, d8, d9] which is ugly and doesn't
match the CFI_INSTRUCTIONs we're generating either (so Dwarf info would be
broken).
This switches the order of vpush/vpop (in both prologue and epilogue,
obviously) so that the Dwarf locations are correct again.
rdar://problem/16264856
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203655 91177308-0d34-0410-b5e6-96231b3b80d8
I could fold the callers into their one call site, but the indirection
(given how verbose choosing the section is) seemed helpful.
The use of a member function pointer's a bit "tricky", but seems limited
enough, the call sites are simple/clean/clear, and there's only one use.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203619 91177308-0d34-0410-b5e6-96231b3b80d8
the first run of the polly buildbot failed, and then it started passing.
This is due to the fact that the buildbot re-builds in an existing directory,
and the first run does not have WITH_POLLY set when it enters tools/.
Thus, cmake ignores the tools/polly dir in the first run, and then because
it reuses the CMakeCache.txt of the previous run, it has the WITH_POLLY set
by the previous run, and so it passes the second time.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203615 91177308-0d34-0410-b5e6-96231b3b80d8
Add a utility function to convert the Windows path separator to Unix style path
separators. This is used by a subsequent change in clang to enable the use of
Windows SDK headers on Linux.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203611 91177308-0d34-0410-b5e6-96231b3b80d8
The function hasReliableSymbolDifference had exactly one use in the MachO
writer. It is also only true for X86_64. In fact, the comments refers to
"Darwin x86_64" and everything else, so this makes the code match the
comment.
If this is to be abstracted again, it should be a property of
TargetObjectWriter, like useAggressiveSymbolFolding.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203605 91177308-0d34-0410-b5e6-96231b3b80d8
Before this patch the unix code for creating hardlinks was unused. The code
for creating symbolic links was implemented in lib/Support/LockFileManager.cpp
and the code for creating hard links in lib/Support/*/Path.inc.
The only use we have for these is in LockFileManager.cpp and it can use both
soft and hard links. Just have a create_link function that creates one or the
other depending on the platform.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203596 91177308-0d34-0410-b5e6-96231b3b80d8
GuardMalloc can print info to stderr, causing these tests to fail.
Since FileCheck errors on empty inputs, just add a bit of dummy
data to make it happy.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203595 91177308-0d34-0410-b5e6-96231b3b80d8
When resolving a function call to an external routine, the dynamic
loader must patch the "nop" after the branch instruction to a load
that restores the TOC register.
Current code does that, but only with the *first* instance of a call
to any particular external routine, i.e. at the point where it also
allocates the call stub. With subsequent calls to the same routine,
current code neglects to patch in the TOC restore code. This is a
bug, and leads to corrupt TOC pointers in those cases.
Fixed by patching in restore code every time.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203580 91177308-0d34-0410-b5e6-96231b3b80d8
Use the options in the ARMISelLowering to control whether tail calls are
optimised or not. Previously, this option was entirely ignored on the ARM
target and only honoured on x86.
This option is mostly useful in profiling scenarios. The default remains that
tail call optimisations will be applied.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203577 91177308-0d34-0410-b5e6-96231b3b80d8
This option is from 2010, designed to work around a linker issue on Darwin for
ARM. According to grosbach this is no longer an issue and this option can
safely be removed.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203576 91177308-0d34-0410-b5e6-96231b3b80d8
Tail call optimisation was previously disabled on all targets other than
iOS5.0+. This enables the tail call optimisation on all Thumb 2 capable
platforms.
The test adjustments are to remove the IR hint "tail" to function invocation.
The tests were designed assuming that tail call optimisations would not kick in
which no longer holds true.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203575 91177308-0d34-0410-b5e6-96231b3b80d8
After r203553 overflow intrinsics and their non-intrinsic (normal)
instruction get hashed to the same value. This patch prevents PRE from
moving an instruction into a predecessor block, and trying to add a phi
node that gets two different types (the intrinsic result and the
non-intrinsic result), resulting in a failing assert.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203574 91177308-0d34-0410-b5e6-96231b3b80d8
ATOMIC_STORE operations always get here as a lowered ATOMIC_SWAP, so there's no
need for any code to handle them specially.
There should be no functionality change so no tests.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203567 91177308-0d34-0410-b5e6-96231b3b80d8
The syntax for "cmpxchg" should now look something like:
cmpxchg i32* %addr, i32 42, i32 3 acquire monotonic
where the second ordering argument gives the required semantics in the case
that no exchange takes place. It should be no stronger than the first ordering
constraint and cannot be either "release" or "acq_rel" (since no store will
have taken place).
rdar://problem/15996804
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203559 91177308-0d34-0410-b5e6-96231b3b80d8
When an overflow intrinsic is followed by a non-overflow instruction,
replace the latter with an extract. For example:
%sadd = tail call { i32, i1 } @llvm.sadd.with.overflow.i32(i32 %a, i32 %b)
%sadd3 = add i32 %a, %b
Here the add statement will be replaced by an extract.
When an overflow intrinsic follows a non-overflow instruction, a clone
of the intrinsic is inserted before the normal instruction, which makes
it the same as the previous case. Subsequent runs of GVN can then clean
up the duplicate instructions and insert the extract.
This fixes PR8817.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203553 91177308-0d34-0410-b5e6-96231b3b80d8
The official specifications state the name to be ARMNT (as per the Microsoft
Portable Executable and Common Object Format Specification v8.3).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203530 91177308-0d34-0410-b5e6-96231b3b80d8
When the MOVBE instructions are available, use them for 16-bit endian
swapping as well as for 32 and 64 bit.
The patterns were already present on the instructions, but weren't being
matched because the operation was unconditionally marked to 'Expand.'
Change that to be conditional on whether the MOVBE instructions are
available. Use 'rolw' to implement the in-register version (32 and 64
bit have the dedicated 'bswap' instruction for that).
Patch by Louis Gerbarg <lgg@apple.com>.
rdar://15479984
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203524 91177308-0d34-0410-b5e6-96231b3b80d8
In import thunk, jmp is:
- On x86, 0xFF 0x25 [disp32].
- On x64, 0xFF 0x25 [pcrel32].
See also my r144178.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203523 91177308-0d34-0410-b5e6-96231b3b80d8
During LTO, user-supplied definitions of C library functions often
exist. -instcombine uses Module::getOrInsertFunction() to get a handle
on library functions (e.g., @puts, when optimizing @printf).
Previously, Module::getOrInsertFunction() would rename any matching
functions with local linkage, and create a new declaration. In LTO,
this is the opposite of desired behaviour, as it skips by the
user-supplied version of the library function and creates a new
undefined reference which the linker often cannot resolve.
After some discussing with Rafael on the list, it looks like it's
undesired behaviour. If a consumer actually *needs* this behaviour, we
should add new API with a more explicit name.
I added two testcases: one specifically for the -instcombine behaviour
and one for the LTO flow.
<rdar://problem/16165191>
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203513 91177308-0d34-0410-b5e6-96231b3b80d8
the legalization cost must be included to get an accurate
estimation of the total cost of the scalarized vector.
The inaccurate cost triggered unprofitable SLP vectorization on
32-bit X86.
Summary:
Include legalization overhead when computing scalarization cost
Reviewers: hfinkel, nadav
CC: chandlerc, rnk, llvm-commits
Differential Revision: http://llvm-reviews.chandlerc.com/D2992
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203509 91177308-0d34-0410-b5e6-96231b3b80d8
Summary:
When the sample profiles include discriminator information,
use the discriminator values to distinguish instruction weights
in different basic blocks.
This modifies the BodySamples mapping to map <line, discriminator> pairs
to weights. Instructions on the same line but different blocks, will
use different discriminator values. This, in turn, means that the blocks
may have different weights.
Other changes in this patch:
- Add tests for positive values of line offset, discriminator and samples.
- Change data types from uint32_t to unsigned and int and do additional
validation.
Reviewers: chandlerc
CC: llvm-commits
Differential Revision: http://llvm-reviews.chandlerc.com/D2857
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@203508 91177308-0d34-0410-b5e6-96231b3b80d8
