Because the PowerPC vmrgh* and vmrgl* instructions have a built-in
big-endian bias, it is necessary to swap their inputs in little-endian
mode when using them to implement a vector shuffle. This was
previously missed in the vector LE implementation.
There was already logic to distinguish between unary and "normal"
vmrg* vector shuffles, so this patch extends that logic to use a third
option: "swapped" vmrg* vector shuffles that are used for little
endian in place of the "normal" ones.
I've updated the vec-shuffle-le.ll test to check for the expected
register ordering on the generated instructions.
This bug was discovered when testing the LE and ELFv2 patches for
safety if they were backported to 3.4. A different vectorization
decision was made in 3.4 than on mainline trunk, and that exposed the
problem. I've verified this fix takes care of that issue.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213915 91177308-0d34-0410-b5e6-96231b3b80d8
insertions.
The old behavior could cause arbitrarily bad memory usage in the DAG
combiner if there was heavy traffic of adding nodes already on the
worklist to it. This commit switches the DAG combine worklist to work
the same way as the instcombine worklist where we null-out removed
entries and only add new entries to the worklist. My measurements of
codegen time shows slight improvement. The memory utilization is
unsurprisingly dominated by other factors (the IR and DAG itself
I suspect).
This change results in subtle, frustrating churn in the particular order
in which DAG combines are applied which causes a number of minor
regressions where we fail to match a pattern previously matched by
accident. AFAICT, all of these should be using AddToWorklist to directly
or should be written in a less brittle way. None of the changes seem
drastically bad, and a few of the changes seem distinctly better.
A major change required to make this work is to significantly harden the
way in which the DAG combiner handle nodes which become dead
(zero-uses). Previously, we relied on the ability to "priority-bump"
them on the combine worklist to achieve recursive deletion of these
nodes and ensure that the frontier of remaining live nodes all were
added to the worklist. Instead, I've introduced a routine to just
implement that precise logic with no indirection. It is a significantly
simpler operation than that of the combiner worklist proper. I suspect
this will also fix some other problems with the combiner.
I think the x86 changes are really minor and uninteresting, but the
avx512 change at least is hiding a "regression" (despite the test case
being just noise, not testing some performance invariant) that might be
looked into. Not sure if any of the others impact specific "important"
code paths, but they didn't look terribly interesting to me, or the
changes were really minor. The consensus in review is to fix any
regressions that show up after the fact here.
Thanks to the other reviewers for checking the output on other
architectures. There is a specific regression on ARM that Tim already
has a fix prepped to commit.
Differential Revision: http://reviews.llvm.org/D4616
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213727 91177308-0d34-0410-b5e6-96231b3b80d8
This patch adds infrastructure support for passing array types
directly. These can be used by the front-end to pass aggregate
types (coerced to an appropriate array type). The details of the
array type being used inform the back-end about ABI-relevant
properties. Specifically, the array element type encodes:
- whether the parameter should be passed in FPRs, VRs, or just
GPRs/stack slots (for float / vector / integer element types,
respectively)
- what the alignment requirements of the parameter are when passed in
GPRs/stack slots (8 for float / 16 for vector / the element type
size for integer element types) -- this corresponds to the
"byval align" field
Using the infrastructure provided by this patch, a companion patch
to clang will enable two features:
- In the ELFv2 ABI, pass (and return) "homogeneous" floating-point
or vector aggregates in FPRs and VRs (this is similar to the ARM
homogeneous aggregate ABI)
- As an optimization for both ELFv1 and ELFv2 ABIs, pass aggregates
that fit fully in registers without using the "byval" mechanism
The patch uses the functionArgumentNeedsConsecutiveRegisters callback
to encode that special treatment is required for all directly-passed
array types. The isInConsecutiveRegs / isInConsecutiveRegsLast bits set
as a results are then used to implement the required size and alignment
rules in CalculateStackSlotSize / CalculateStackSlotAlignment etc.
As a related change, the ABI routines have to be modified to support
passing floating-point types in GPRs. This is necessary because with
homogeneous aggregates of 4-byte float type we can now run out of FPRs
*before* we run out of the 64-byte argument save area that is shadowed
by GPRs. Any extra floating-point arguments that no longer fit in FPRs
must now be passed in GPRs until we run out of those too.
Note that there was already code to pass floating-point arguments in
GPRs used with vararg parameters, which was done by writing the argument
out to the argument save area first and then reloading into GPRs. The
patch re-implements this, however, in favor of code packing float arguments
directly via extension/truncation, BITCAST, and BUILD_PAIR operations.
This is required to support the ELFv2 ABI, since we cannot unconditionally
write to the argument save area (which the caller might not have allocated).
The change does, however, affect ELFv1 varags routines too; but even here
the overall effect should be advantageous: Instead of loading the argument
into the FPR, then storing the argument to the stack slot, and finally
reloading the argument from the stack slot into a GPR, the new code now
just loads the argument into the FPR, and subsequently loads the argument
into the GPR (via BITCAST). That BITCAST might imply a save/reload from
a stack temporary (in which case we're no worse than before); but it
might be implemented more efficiently in some cases.
The final part of the patch enables up to 8 FPRs and VRs for argument
return in PPCCallingConv.td; this is required to support returning
ELFv2 homogeneous aggregates. (Note that this doesn't affect other ABIs
since LLVM wil only look for which register to use if the parameter is
marked as "direct" return anyway.)
Reviewed by Hal Finkel.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213493 91177308-0d34-0410-b5e6-96231b3b80d8
This is a minor improvement in the ELFv2 ABI. In ELFv1, DWARF CFI
would represent a saved CR word (holding CR fields CR2, CR3, and CR4)
using just a single CFI record refering to CR2. In ELFv2 instead,
each of the CR fields is represented by its own CFI record. The
advantage is that the compiler can now chose to save just a single
(or two) CR fields instead of all of them, if those are the only ones
that actually need saving. That can lead to more efficient code using
mf(o)crf instead of the (slow) mfcr instruction.
Note that this patch does not (yet) implement this more efficient
code generation, but it does implement the part that is required to
be ABI compliant: creating multiple CFI records if multiple CR fields
are saved.
Reviewed by Hal Finkel.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213492 91177308-0d34-0410-b5e6-96231b3b80d8
The ELFv2 ABI reduces the amount of stack required to implement an
ABI-compliant function call in two ways:
* the "linkage area" is reduced from 48 bytes to 32 bytes by
eliminating two unused doublewords
* the 64-byte "parameter save area" is now optional and need not be
present in certain cases (it remains mandatory in functions with
variable arguments, and functions that have any parameter that is
passed on the stack)
The following patch implements this required changes:
- reducing the linkage area, and associated relocation of the TOC save
slot, in getLinkageSize / getTOCSaveOffset (this requires updating all
callers of these routines to pass in the isELFv2ABI flag).
- (partially) handling the case where the parameter save are is optional
This latter part requires some extra explanation: Currently, we still
always allocate the parameter save area when *calling* a function.
That is certainly always compliant with the ABI, but may cause code to
allocate stack unnecessarily. This can be addressed by a follow-on
optimization patch.
On the *callee* side, in LowerFormalArguments, we *must* track
correctly whether the ABI guarantees that the caller has allocated
the parameter save area for our use, and the patch does so. However,
there is one complication: the code that handles incoming "byval"
arguments will currently *always* write to the parameter save area,
because it has to force incoming register arguments to the stack since
it must return an *address* to implement the byval semantics.
To fix this, the patch changes the LowerFormalArguments code to write
arguments to a freshly allocated stack slot on the function's own stack
frame instead of the argument save area in those cases where that area
is not present.
Reviewed by Hal Finkel.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213490 91177308-0d34-0410-b5e6-96231b3b80d8
This patch builds upon the two preceding MC changes to implement the
basic ELFv2 function call convention. In the ELFv1 ABI, a "function
descriptor" was associated with every function, pointing to both the
entry address and the related TOC base (and a static chain pointer
for nested functions). Function pointers would actually refer to that
descriptor, and the indirect call sequence needed to load up both entry
address and TOC base.
In the ELFv2 ABI, there are no more function descriptors, and function
pointers simply refer to the (global) entry point of the function code.
Indirect function calls simply branch to that address, after loading it
up into r12 (as required by the ABI rules for a global entry point).
Direct function calls continue to just do a "bl" to the target symbol;
this will be resolved by the linker to the local entry point of the
target function if it is local, and to a PLT stub if it is global.
That PLT stub would then load the (global) entry point address of the
final target into r12 and branch to it. Note that when performing a
local function call, r2 must be set up to point to the current TOC
base: if the target ends up local, the ABI requires that its local
entry point is called with r2 set up; if the target ends up global,
the PLT stub requires that r2 is set up.
This patch implements all LLVM changes to implement that scheme:
- No longer create a function descriptor when emitting a function
definition (in EmitFunctionEntryLabel)
- Emit two entry points *if* the function needs the TOC base (r2)
anywhere (this is done EmitFunctionBodyStart; note that this cannot
be done in EmitFunctionBodyStart because the global entry point
prologue code must be *part* of the function as covered by debug info).
- In order to make use tracking of r2 (as needed above) work correctly,
mark direct function calls as implicitly using r2.
- Implement the ELFv2 indirect function call sequence (no function
descriptors; load target address into r12).
- When creating an ELFv2 object file, emit the .abiversion 2 directive
to tell the linker to create the appropriate version of PLT stubs.
Reviewed by Hal Finkel.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213489 91177308-0d34-0410-b5e6-96231b3b80d8
The PPCTargetLowering::SelectAddressRegImm routine needs to handle
FrameIndex nodes in a special manner, by tranlating them into a
TargetFrameIndex node. This was done in most cases, but seems to
have been neglected in one path: when the input tree has an OR of
the FrameIndex with an immediate. This can happen if the FrameIndex
can be proven to be sufficiently aligned that an OR of that immediate
is equivalent to an ADD.
The missing handling of FrameIndex in that case caused the SelectionDAG
instruction selection to miss opportunities to merge the OR back into
the FrameIndex node, leading to superfluous addi/ori instructions in
the final assembler output.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213482 91177308-0d34-0410-b5e6-96231b3b80d8
This adds initial support for PPC32 ELF PIC (Position Independent Code; the
-fPIC variety), thus rectifying a long-standing deficiency in the PowerPC
backend.
Patch by Justin Hibbits!
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213427 91177308-0d34-0410-b5e6-96231b3b80d8
This commit fixes a bug in PPCRegisterInfo::isFrameOffsetLegal that
could result in the LocalStackAlloc pass creating an MI instruction
out-of-range displacement:
%vreg17<def> = LD 33184, %vreg31; mem:LD8[%g](align=32)
%G8RC:%vreg17 G8RC_and_G8RC_NOX0:%vreg31
(In final assembler output the top bits are stripped off, resulting
in a negative offset loading from below the stack pointer.)
Common code expects the isFrameOffsetLegal routine to verify whether
adding a given offset to the offset already present in the instruction
results in a valid displacement. However, on PowerPC the routine
did not take the already present instruction offset into account.
This commit fixes isFrameOffsetLegal to add the instruction offset,
and updates a local caller (needsFrameBaseReg) to no longer add the
instruction offset itself before calling isFrameOffsetLegal.
Reviewed by Hal Finkel.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@212832 91177308-0d34-0410-b5e6-96231b3b80d8
Arguments passed as "byval align" should get the specified alignment
in the parameter save area. There was some code in PPCISelLowering.cpp
that attempted to implement this, but this didn't work correctly:
while code did update the ArgOffset value, it neglected to update
the PtrOff value (which was already computed from the old ArgOffset),
and it also neglected to update GPR_idx -- fields skipped due to
alignment in the save area must likewise be skipped in GPRs.
This patch fixes and simplifies this logic by:
- handling argument offset alignment right at the beginning
of argument processing, using a new helper routine
CalculateStackSlotAlignment (this avoids having to update
PtrOff and other derived values later on)
- not tracking GPR_idx separately, but always computing the
correct GPR_idx for each argument *from* its ArgOffset
- removing some redundant computation in LowerFormalArguments:
MinReservedArea must equal ArgOffset after argument processing,
so there's no use in computing it twice.
[This doesn't change the behavior of the current clang front-end,
since that never creates "byval align" arguments at the moment.
This will change with a follow-on patch, however.]
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@212476 91177308-0d34-0410-b5e6-96231b3b80d8
There were two issues here:
1. At the very least, scattered relocations cannot use the same code to
determine the corresponding symbol being referred to. For some reason we
pretend there is no symbol, even when one actually exists in the symtab, so to
match this behaviour getRelocationSymbol should simply return symbols_end for
scattered relocations.
2. Printing "-" when we can't get a symbol (including the scattered case, but
not exclusively), isn't that helpful. In both cases there *is* interesting
information in that field, so we should print it. As hex will do.
Small part of rdar://problem/17553104
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@212332 91177308-0d34-0410-b5e6-96231b3b80d8
The PowerPC 128-bit long double data type (ppcf128 in LLVM) is in fact a
pair of two doubles, where one is considered the "high" or
more-significant part, and the other is considered the "low" or
less-significant part. When a ppcf128 value is stored in memory or a
register pair, the high part always comes first, i.e. at the lower
memory address or in the lower-numbered register, and the low part
always comes second. This is true both on big-endian and little-endian
PowerPC systems. (Similar to how with a complex number, the real part
always comes first and the imaginary part second, no matter the byte
order of the system.)
This was implemented incorrectly for little-endian systems in LLVM.
This commit fixes three related issues:
- When printing an immediate ppcf128 constant to assembler output
in emitGlobalConstantFP, emit the high part first on both big-
and little-endian systems.
- When lowering a ppcf128 type to a pair of f64 types in SelectionDAG
(which is used e.g. when generating code to load an argument into a
register pair), use correct low/high part ordering on little-endian
systems.
- In a related issue, because lowering ppcf128 into a pair of f64 must
operate differently from lowering an int128 into a pair of i64,
bitcasts between ppcf128 and int128 must not be optimized away by the
DAG combiner on little-endian systems, but must effect a word-swap.
Reviewed by Hal Finkel.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@212274 91177308-0d34-0410-b5e6-96231b3b80d8
I've run into a bug where current LLVM at -O0 (with fast-isel)
generated invalid code like:
ld 0, 20936(1) # 8-byte Folded Reload
stw 12, 10348(0)
stw 12, 10344(0)
The underlying vreg had been introduced as base register by the
Local Stack Slot Allocation pass. That register was constrained
to G8RC by PPCRegisterInfo::materializeFrameBaseRegister to match
the ADDI instruction used to set it, but it was *not* constrained
to G8RC_NOX0 to fit the *use* of the register in an address.
That should have happened in PPCRegisterInfo::resolveFrameIndex.
This patch adds an appropriate constrainRegClass call.
Reviewed by Hal Finkel.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211897 91177308-0d34-0410-b5e6-96231b3b80d8
[LLVM part]
These patches rename the loop unrolling and loop vectorizer metadata
such that they have a common 'llvm.loop.' prefix. Metadata name
changes:
llvm.vectorizer.* => llvm.loop.vectorizer.*
llvm.loopunroll.* => llvm.loop.unroll.*
This was a suggestion from an earlier review
(http://reviews.llvm.org/D4090) which added the loop unrolling
metadata.
Patch by Mark Heffernan.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211710 91177308-0d34-0410-b5e6-96231b3b80d8
PR20071 identifies a problem in PowerPC's fast-isel implementation for
floating-point conversion to integer. The fctiduz instruction was added in
Power ISA 2.06 (i.e., Power7 and later). However, this instruction is being
generated regardless of which 64-bit PowerPC target is selected.
The intent is for fast-isel to punt to DAG selection when this instruction is
not available. This patch implements that change. For testing purposes, the
existing fast-isel-conversion.ll test adds a RUN line for -mcpu=970 and tests
for the expected code generation. Additionally, the existing test
fast-isel-conversion-p5.ll was found to be incorrectly expecting the
unavailable instruction to be generated. I've removed these test variants
since we have adequate coverage in fast-isel-conversion.ll.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211627 91177308-0d34-0410-b5e6-96231b3b80d8
The PPCFrameLowering::determineFrameLayout routine currently ensures
that every function that allocates a stack frame provides space for the
parameter save area (via PPCFrameLowering::getMinCallFrameSize).
This is actually not necessary. There may be functions that never call
another routine but still allocate a frame; those do not require the
parameter save area. In the future, with the ELFv2 ABI, even some
routines that do call other functions do not need to allocate the
parameter save area.
While it is not a bug to allocate the parameter area when it is not
needed, it is better to avoid it to save stack space.
Note that when any particular function call requires the parameter save
area, this space will already have been included by ABI code in the size
the CALLSEQ_START insn is annotated with, and therefore included in the
size returned by MFI->getMaxCallFrameSize().
This means that determineFrameLayout simply does not need to care about
the parameter save area. (It still needs to ensure that every frame
provides the linkage area.) This is implemented by this patch.
Note that this exposed a bug in the new fast-isel code where the parameter
area was *not* included in the CALLSEQ_START size; this is also fixed.
A couple of test cases needed to be adapted for the new (smaller) stack
frame size those tests now see.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211495 91177308-0d34-0410-b5e6-96231b3b80d8
Current 64-bit SVR4 code seems to have some remnants of Darwin code
in AltiVec argument handing. This had the effect that AltiVec arguments
(or subsequent arguments) were not correctly placed in the parameter area
in some cases.
The correct behaviour with the 64-bit SVR4 ABI is:
- All AltiVec arguments take up space in the parameter area, just like
any other arguments, whether vararg or not.
- They are always 16-byte aligned, skipping a parameter area doubleword
(and the associated GPR, if any), if necessary.
This patch implements the correct behaviour and adds a test case.
(Verified against GCC behaviour via the ABI compat test suite.)
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211492 91177308-0d34-0410-b5e6-96231b3b80d8
When small arguments (structures < 8 bytes or "float") are passed in a
stack slot in the ppc64 SVR4 ABI, they must reside in the least
significant part of that slot. On BE, this means that an offset needs
to be added to the stack address of the parameter, but on LE, the least
significant part of the slot has the same address as the slot itself.
This changes the PowerPC back-end ABI code to only add the small
argument stack slot offset for BE. It also adds test cases to verify
the correct behavior on both BE and LE.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211368 91177308-0d34-0410-b5e6-96231b3b80d8
During an indirect function call sequence on the 64-bit SVR4 ABI,
generate code must load and then restore the TOC register.
This does not use a regular LOAD instruction since the TOC
register r2 is marked as reserved. Instead, the are two
special instruction patterns:
let RST = 2, DS = 2 in
def LDinto_toc: DSForm_1a<58, 0, (outs), (ins g8rc:$reg),
"ld 2, 8($reg)", IIC_LdStLD,
[(PPCload_toc i64:$reg)]>, isPPC64;
let RST = 2, DS = 10, RA = 1 in
def LDtoc_restore : DSForm_1a<58, 0, (outs), (ins),
"ld 2, 40(1)", IIC_LdStLD,
[(PPCtoc_restore)]>, isPPC64;
Note that these not only restrict the destination of the
load to r2, but they also restrict the *source* of the
load to particular address combinations. The latter is
a problem when we want to support the ELFv2 ABI, since
there the TOC save slot is no longer at 40(1).
This patch replaces those two instructions with a single
instruction pattern that only hard-codes r2 as destination,
but supports generic addresses as source. This will allow
supporting the ELFv2 ABI, and also helps generate more
efficient code for calls to absolute addresses (allowing
simplification of the ppc64-calls.ll test case).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211193 91177308-0d34-0410-b5e6-96231b3b80d8
As requested by Hal Finkel, this adds back a test for calls to
a known-constant function pointer value, and verifies that the
64-bit SVR4 indirect function call sequence is used.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211190 91177308-0d34-0410-b5e6-96231b3b80d8
The PowerPC back-end uses BLA to implement calls to functions at
known-constant addresses, which is apparently used for certain
system routines on Darwin.
However, with the 64-bit SVR4 ABI, this is actually incorrect.
An immediate function pointer value on this platform is not
directly usable as a target address for BLA:
- in the ELFv1 ABI, the function pointer value refers to the
*function descriptor*, not the code address
- in the ELFv2 ABI, the function pointer value refers to the
global entry point, but BL(A) would only be correct when
calling the *local* entry point
This bug didn't show up since using immediate function pointer
values is not usually done in the 64-bit SVR4 ABI in the first
place. However, I ran into this issue with a certain use case
of LLVM as JIT, where immediate function pointer values were
uses to implement callbacks from JITted code to helpers in
statically compiled code.
Fixed by simply not using BLA with the 64-bit SVR4 ABI.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211174 91177308-0d34-0410-b5e6-96231b3b80d8
Rafael opened http://llvm.org/bugs/show_bug.cgi?id=19893 to track non-optimal
code generation for forming a function address that is local to the compile
unit. The existing code was treating both local and non-local functions
identically.
This patch fixes the problem by properly identifying local functions and
generating the proper addis/addi code. I also noticed that Rafael's earlier
changes to correct the surrounding code in PPCISelLowering.cpp were also
needed for fast instruction selection in PPCFastISel.cpp, so this patch
fixes that code as well.
The existing test/CodeGen/PowerPC/func-addr.ll is modified to test the new
code generation. I've added a -O0 run line to test the fast-isel code as
well.
Tested on powerpc64[le]-unknown-linux-gnu with no regressions.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211056 91177308-0d34-0410-b5e6-96231b3b80d8
This commit adds a weak variant of the cmpxchg operation, as described
in C++11. A cmpxchg instruction with this modifier is permitted to
fail to store, even if the comparison indicated it should.
As a result, cmpxchg instructions must return a flag indicating
success in addition to their original iN value loaded. Thus, for
uniformity *all* cmpxchg instructions now return "{ iN, i1 }". The
second flag is 1 when the store succeeded.
At the DAG level, a new ATOMIC_CMP_SWAP_WITH_SUCCESS node has been
added as the natural representation for the new cmpxchg instructions.
It is a strong cmpxchg.
By default this gets Expanded to the existing ATOMIC_CMP_SWAP during
Legalization, so existing backends should see no change in behaviour.
If they wish to deal with the enhanced node instead, they can call
setOperationAction on it. Beware: as a node with 2 results, it cannot
be selected from TableGen.
Currently, no use is made of the extra information provided in this
patch. Test updates are almost entirely adapting the input IR to the
new scheme.
Summary for out of tree users:
------------------------------
+ Legacy Bitcode files are upgraded during read.
+ Legacy assembly IR files will be invalid.
+ Front-ends must adapt to different type for "cmpxchg".
+ Backends should be unaffected by default.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@210903 91177308-0d34-0410-b5e6-96231b3b80d8
Various masks on shufflevector instructions are recognizable as
specific PowerPC instructions (vector pack, vector merge, etc.).
There is existing code in PPCISelLowering.cpp to recognize the correct
patterns for big endian code. The masks for these instructions are
different for little endian code due to the big-endian numbering
employed by these instructions. This patch adds the recognition code
for little endian.
I've added a new test case test/CodeGen/PowerPC/vec_shuffle_le.ll for
this. The existing recognizer test (vec_shuffle.ll) is unnecessarily
verbose and difficult to read, so I felt it was better to add a new
test rather than modify the old one.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@210536 91177308-0d34-0410-b5e6-96231b3b80d8
The code in PPCTargetLowering::PerformDAGCombine() that handles
unaligned Altivec vector loads generates a lvsl followed by a vperm.
As we've seen in numerous other places, the vperm instruction has a
big-endian bias, and this is fixed for little endian by complementing
the permute control vector and swapping the input operands. In this
case the lvsl is providing the permute control vector. Rather than
generating an lvsl and a complement operation, it is sufficient to
generate an lvsr instruction instead. Thus for LE code generation we
will generate an lvsr rather than an lvsl, and swap the other input
arguments on the vperm.
The existing test/CodeGen/PowerPC/vec_misalign.ll is updated to test
the code generation for PPC64 and PPC64LE, in addition to the existing
PPC32/G5 testing.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@210493 91177308-0d34-0410-b5e6-96231b3b80d8
The existing code in PPCTargetLowering::LowerMUL() for multiplying two
v16i8 values assumes that vector elements are numbered in big-endian
order. For little-endian targets, the vector element numbering is
reversed, but the vmuleub, vmuloub, and vperm instructions still
assume big-endian numbering. To account for this, we must adjust the
permute control vector and reverse the order of the input registers on
the vperm instruction.
The existing test/CodeGen/PowerPC/vec_mul.ll is updated to be executed
on powerpc64 and powerpc64le targets as well as the original powerpc
(32-bit) target.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@210474 91177308-0d34-0410-b5e6-96231b3b80d8
This patch fixes a couple of lowering issues for little endian
PowerPC. The code for lowering BUILD_VECTOR contains a number of
optimizations that are only valid for big endian. For now, we disable
those optimizations for correctness. In the future, we will add
analogous optimizations that are correct for little endian.
When lowering a SHUFFLE_VECTOR to a VPERM operation, we again need to
make the now-familiar transformation of swapping the input operands
and complementing the permute control vector. Correctness of this
transformation is tested by the accompanying test case.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@210336 91177308-0d34-0410-b5e6-96231b3b80d8
Chandler correctly pointed out that I need an LLVM IR test for
r210282, which modified the vperm -> shuffle transform for little
endian PowerPC. This patch provides that test.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@210297 91177308-0d34-0410-b5e6-96231b3b80d8
This seems to match what gcc does for ppc and what every other llvm
backend does.
This is a fixed version of r209638. The difference is to avoid any change
in behavior for functions. The logic for using constant pools for function
addresseses is spread over a few places and we have to keep them in sync.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@209821 91177308-0d34-0410-b5e6-96231b3b80d8
This reverts commit r209638 because it broke self-hosting on ppc64/Linux. (the
Clang-compiled TableGen would segfault because it jumped to an invalid address
from within _ZNK4llvm17ManagedStaticBase21RegisterManagedStaticEPFPvvEPFvS1_E
(which is within the command-line parameter registration process)).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@209745 91177308-0d34-0410-b5e6-96231b3b80d8
In PPCISelLowering.cpp: PPCTargetLowering::LowerBUILD_VECTOR(), there
is an optimization for certain patterns to generate one or two vector
splats followed by a vector add or subtract. This operation is
represented by a VADD_SPLAT in the selection DAG. Prior to this
patch, it was possible for the VADD_SPLAT to be assigned the wrong
data type, causing incorrect code generation. This patch corrects the
problem.
Specifically, the code previously assigned the value type of the
BUILD_VECTOR node to the newly generated VADD_SPLAT node. This is
correct much of the time, but not always. The problem is that the
call to isConstantSplat() may return a SplatBitSize that is not the
same as the number of bits in the original element vector type. The
correct type to assign is a vector type with the same element bit size
as SplatBitSize.
The included test case shows an example of this, where the
BUILD_VECTOR node has a type of v16i8. The vector to be built is {0,
16, 0, 16, 0, 16, 0, 16, 0, 16, 0, 16, 0, 16, 0, 16}. isConstantSplat
detects that we can generate a splat of 16 for type v8i16, which is
the type we must assign to the VADD_SPLAT node. If we do not, we
generate a vspltisb of 8 and a vaddubm, which generates the incorrect
result {16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16,
16}. The correct code generation is a vspltish of 8 and a vadduhm.
This patch also corrected code generation for
CodeGen/PowerPC/2008-07-10-SplatMiscompile.ll, which had been marked
as an XFAIL, so we can remove the XFAIL from the test case.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@209662 91177308-0d34-0410-b5e6-96231b3b80d8
The SplitIndexingFromLoad changes exposed a latent isel bug in the PowerPC64
backend. We matched an immediate offset with STWX8 even though it only
supports register offset.
The culprit is the complex-pattern predicate, SelectAddrIdx, which decides
that if the offset is not ISD::Constant it must be a register.
Many thanks to Bill Schmidt for testing this.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@209219 91177308-0d34-0410-b5e6-96231b3b80d8
Many old tests using prior schemas still had some brokenness here (both
indirect arrays and arrays with single bogus elements). Fixed those up
so they don't hit the new assertions.
Also reduced nesting in some places, etc.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@208817 91177308-0d34-0410-b5e6-96231b3b80d8
Support for the intrinsics that read from and write to global named registers
is added for r1, r2 and r13 (depending on the subtarget).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@208509 91177308-0d34-0410-b5e6-96231b3b80d8
The counter-loops formation pass needs to know what operations might be
function calls (because they can't appear in counter-based loops). On PPC32,
128-bit shifts might be runtime calls (even though you can't use __int128 on
PPC32, it seems that SROA might form them).
Fixes PR19709.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@208501 91177308-0d34-0410-b5e6-96231b3b80d8
We had been using the known-zero values of the operand of the or to construct
the mask for an rlwimi; this is not quite correct, but fine when the mask is
constant. When the mask is constant, then the known zeros of the operand must
be a superset of the zeros in the mask. However, when the mask is not a
constant, then there might be bits in the operand that are not known to be zero
that, at runtime, might be zero in the mask. Therefore, we check that any bits
not known to be zero *are* known to be one in the mask. Otherwise, we can't
fold the mask with the or and shift.
This was revealed as a miscompile of
MultiSource/Benchmarks/BitBench/drop3/drop3 when I started experimenting with
constant hoisting.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@206136 91177308-0d34-0410-b5e6-96231b3b80d8
We had disabled use of TBAA during CodeGen (even when otherwise using AA)
because the ptrtoint/inttoptr used by CGP for address sinking caused BasicAA to
miss basic type punning that it should catch (and, thus, we'd fail to override
TBAA when we should).
However, when AA is in use during CodeGen, CGP now uses normal GEPs and
bitcasts, instead of ptrtoint/inttoptr, when doing address sinking. As a
result, BasicAA should be able to make us do the right thing in the face of
type-punning, and it seems safe to enable use of TBAA again. self-hosting seems
fine on PPC64/Linux on the P7, with TBAA enabled and -misched=shuffle.
Note: We still don't update TBAA when merging stack slots, although because
BasicAA should now catch all such cases, this is no longer a blocking issue.
Nevertheless, I plan to commit code to deal with this properly in the near
future.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@206093 91177308-0d34-0410-b5e6-96231b3b80d8
The current memory-instruction optimization logic in CGP, which sinks parts of
the address computation that can be adsorbed by the addressing mode, does this
by explicitly converting the relevant part of the address computation into
IR-level integer operations (making use of ptrtoint and inttoptr). For most
targets this is currently not a problem, but for targets wishing to make use of
IR-level aliasing analysis during CodeGen, the use of ptrtoint/inttoptr is a
problem for two reasons:
1. BasicAA becomes less powerful in the face of the ptrtoint/inttoptr
2. In cases where type-punning was used, and BasicAA was used
to override TBAA, BasicAA may no longer do so. (this had forced us to disable
all use of TBAA in CodeGen; something which we can now enable again)
This (use of GEPs instead of ptrtoint/inttoptr) is not currently enabled by
default (except for those targets that use AA during CodeGen), and so aside
from some PowerPC subtargets and SystemZ, there should be no change in
behavior. We may be able to switch completely away from the ptrtoint/inttoptr
sinking on all targets, but further testing is required.
I've doubled-up on a number of existing tests that are sensitive to the
address sinking behavior (including some store-merging tests that are
sensitive to the order of the resulting ADD operations at the SDAG level).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@206092 91177308-0d34-0410-b5e6-96231b3b80d8
gcc inline asm supports specifying "cc" as a clobber of all condition
registers. Add just enough modeling of the full register to make this work.
Fixed PR19326.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@205630 91177308-0d34-0410-b5e6-96231b3b80d8
If we have two unique values for a v2i64 build vector, this will always result
in two vector loads if we expand using shuffles. Only one is necessary.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@205231 91177308-0d34-0410-b5e6-96231b3b80d8
