Create debug_inlined dwarf section using these information. This info is used by gdb, at least on Darwin, to enable better experience debugging inlined functions. See DwarfWriter.cpp for more information on structure of debug_inlined section.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@68847 91177308-0d34-0410-b5e6-96231b3b80d8
register destinations that are tied to source operands. The
TargetInstrDescr::findTiedToSrcOperand method silently fails for inline
assembly. The existing MachineInstr::isRegReDefinedByTwoAddr was very
close to doing what is needed, so this revision makes a few changes to
that method and also renames it to isRegTiedToUseOperand (for consistency
with the very similar isRegTiedToDefOperand and because it handles both
two-address instructions and inline assembly with tied registers).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@68714 91177308-0d34-0410-b5e6-96231b3b80d8
with SUBREG_TO_REG, teach SimpleRegisterCoalescing to coalesce
SUBREG_TO_REG instructions (which are similar to INSERT_SUBREG
instructions), and teach the DAGCombiner to take advantage of this on
targets which support it. This eliminates many redundant
zero-extension operations on x86-64.
This adds a new TargetLowering hook, isZExtFree. It's similar to
isTruncateFree, except it only applies to actual definitions, and not
no-op truncates which may not zero the high bits.
Also, this adds a new optimization to SimplifyDemandedBits: transform
operations like x+y into (zext (add (trunc x), (trunc y))) on targets
where all the casts are no-ops. In contexts where the high part of the
add is explicitly masked off, this allows the mask operation to be
eliminated. Fix the DAGCombiner to avoid undoing these transformations
to eliminate casts on targets where the casts are no-ops.
Also, this adds a new two-address lowering heuristic. Since
two-address lowering runs before coalescing, it helps to be able to
look through copies when deciding whether commuting and/or
three-address conversion are profitable.
Also, fix a bug in LiveInterval::MergeInClobberRanges. It didn't handle
the case that a clobber range extended both before and beyond an
existing live range. In that case, multiple live ranges need to be
added. This was exposed by the new subreg coalescing code.
Remove 2008-05-06-SpillerBug.ll. It was bugpoint-reduced, and the
spiller behavior it was looking for no longer occurrs with the new
instruction selection.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@68576 91177308-0d34-0410-b5e6-96231b3b80d8
When compiling in Thumb mode, only the low (R0-R7) registers are available
for most instructions. Breaking the low registers into a new register class
handles this. Uses of R12, SP, etc, are handled explicitly where needed
with copies inserted to move results into low registers where the rest of
the code generator can deal with them.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@68545 91177308-0d34-0410-b5e6-96231b3b80d8
Note that these are distinct from TargetInstrInfo::INSERT_SUBREG
and TargetInstrInfo::EXTRACT_SUBREG, which are used.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@68355 91177308-0d34-0410-b5e6-96231b3b80d8
x * 40
=>
shlq $3, %rdi
leaq (%rdi,%rdi,4), %rax
This has the added benefit of allowing more multiply to be folded into addressing mode. e.g.
a * 24 + b
=>
leaq (%rdi,%rdi,2), %rax
leaq (%rsi,%rax,8), %rax
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@67917 91177308-0d34-0410-b5e6-96231b3b80d8
that has not been JIT'd yet, the callee is put on a list of pending functions
to JIT. The call is directed through a stub, which is updated with the address
of the function after it has been JIT'd. A new interface for allocating and
updating empty stubs is provided.
Add support for removing the ModuleProvider the JIT was created with, which
would otherwise invalidate the JIT's PassManager, which is initialized with the
ModuleProvider's Module.
Add support under a new ExecutionEngine flag for emitting the infomration
necessary to update Function and GlobalVariable stubs after JITing them, by
recording the address of the stub and the name of the GlobalValue. This allows
code to be copied from one address space to another, where libraries may live
at different virtual addresses, and have the stubs updated with their new
correct target addresses.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@64906 91177308-0d34-0410-b5e6-96231b3b80d8
suprise to some callers, e.g. register coalescer. For now, add an parameter
that tells AnalyzeBranch whether it's safe to modify the mbb. A better
solution is out there, but I don't have time to deal with it right now.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@64124 91177308-0d34-0410-b5e6-96231b3b80d8
target directories themselves. This also means that VMCore no longer
needs to know about every target's list of intrinsics. Future work
will include converting the PowerPC target to this interface as an
example implementation.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@63765 91177308-0d34-0410-b5e6-96231b3b80d8
dagcombines that help it match in several more cases. Add
several more cases to test/CodeGen/X86/bt.ll. This doesn't
yet include matching for BT with an immediate operand, it
just covers more register+register cases.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@63266 91177308-0d34-0410-b5e6-96231b3b80d8
new isOperationLegalOrCustom, which does what isOperationLegal
previously did.
Update a bunch of callers to use isOperationLegalOrCustom
instead of isOperationLegal. In some case it wasn't obvious
which behavior is desired; when in doubt I changed then to
isOperationLegalOrCustom as that preserves their previous
behavior.
This is for the second half of PR3376.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@63212 91177308-0d34-0410-b5e6-96231b3b80d8
doesn't support it. The default is set to 'true', so this should not
impact any other target backends.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@63058 91177308-0d34-0410-b5e6-96231b3b80d8
