The MOV64ri64i32 instruction required hacky MCInst lowering because it
was allocated as setting a GR64, but the eventual instruction ("movl")
only set a GR32. This converts it into a so-called "MOV32ri64" which
still accepts a (appropriate) 64-bit immediate but defines a GR32.
This is then converted to the full GR64 by a SUBREG_TO_REG operation,
thus keeping everyone happy.
This fixes a typo in the opcode field of the original patch, which
should make the legact JIT work again (& adds test for that problem).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@183068 91177308-0d34-0410-b5e6-96231b3b80d8
NOTE: If this broke your out-of-tree backend, in *RegisterInfo.td, change
the instances of SubRegIndex that have a comps template arg to use the
ComposedSubRegIndex class instead.
In TableGen land, this adds Size and Offset attributes to SubRegIndex,
and the ComposedSubRegIndex class, for which the Size and Offset are
computed by TableGen. This also adds an accessor in MCRegisterInfo, and
Size/Offsets for the X86 and ARM subreg indices.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@183020 91177308-0d34-0410-b5e6-96231b3b80d8
These instructions are deprecated oddities, but we still need to be able to
disassemble (and reassemble) them if and when they're encountered.
Patch by Amaury de la Vieuville.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@183011 91177308-0d34-0410-b5e6-96231b3b80d8
The disassembly of VEXT instructions was too lax in the bits checked. This
fixes the case where the instruction affects Q-registers but a misaligned lane
was specified (should be UNDEFINED).
Patch by Amaury de la Vieuville
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@183003 91177308-0d34-0410-b5e6-96231b3b80d8
Unlike most -- hopefully "all other", but I'm still checking -- memory
instructions we support, LOAD REVERSED and STORE REVERSED may access
the memory location several times. This means that they are not suitable
for volatile loads and stores.
This patch is a prerequisite for better atomic load and store support.
The same principle applies there: almost all memory instructions we
support are inherently atomic ("block concurrent"), but LOAD REVERSED
and STORE REVERSED are exceptions.
Other instructions continue to allow volatile operands. I will add
positive "allows volatile" tests at the same time as the "allows atomic
load or store" tests.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@183002 91177308-0d34-0410-b5e6-96231b3b80d8
Now that 3.3 is branched, we are re-enabling virtual registers to help
iron out bugs before the next release. Some of the post-RA passes do
not play well with virtual registers, so we disable them for now. The
needed functionality of the PrologEpilogInserter pass is copied to a
new backend-specific NVPTXPrologEpilog pass.
The test for this commit is not breaking the existing tests.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182998 91177308-0d34-0410-b5e6-96231b3b80d8
The MOV64ri64i32 instruction required hacky MCInst lowering because it was
allocated as setting a GR64, but the eventual instruction ("movl") only set a
GR32. This converts it into a so-called "MOV32ri64" which still accepts a
(appropriate) 64-bit immediate but defines a GR32. This is then converted to
the full GR64 by a SUBREG_TO_REG operation, thus keeping everyone happy.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182991 91177308-0d34-0410-b5e6-96231b3b80d8
r182877 broke MCJIT tests on ARM and r182937 was working around another failure
by r182877.
This should make the ARM bots green.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182960 91177308-0d34-0410-b5e6-96231b3b80d8
Instead of having a bunch of separate MOV8r0, MOV16r0, ... pseudo-instructions,
it's better to use a single MOV32r0 (which will expand to "xorl %reg, %reg")
and obtain other sizes with EXTRACT_SUBREG and SUBREG_TO_REG. The encoding is
smaller and partial register updates can sometimes be avoided.
Until recently, this sequence was a barrier to rematerialization though. That
should now be fixed so it's an appropriate time to make the change.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182928 91177308-0d34-0410-b5e6-96231b3b80d8
32-bit writes on amd64 zero out the high bits of the corresponding 64-bit
register. LLVM makes use of this for zero-extension, but until now relied on
custom MCLowering and other code to fixup instructions. Now we have proper
handling of sub-registers, this can be done by creating SUBREG_TO_REG
instructions at selection-time.
Should be no change in functionality.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182921 91177308-0d34-0410-b5e6-96231b3b80d8
The code to distinguish between unaligned and aligned addresses was
already there, so this is mostly just a switch-on-and-test process.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182920 91177308-0d34-0410-b5e6-96231b3b80d8
Fixes PR16146: gdb.base__call-ar-st.exp fails after
pre-RA-sched=source fixes.
Patch by Xiaoyi Guo!
This also fixes an unsupported dbg.value test case. Codegen was
previously incorrect but the test was passing by luck.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182885 91177308-0d34-0410-b5e6-96231b3b80d8
This corrects a problem where x86 instructions that implicitly define/use both
an A-register (RAX, EAX, ..) and EFLAGS were declared as only defining/using
EFLAGS, because the outer "let Defs/Uses = [EFLAGS]" in the various multiclasses
overrides the "let Defs/Uses = [areg]" in BinOpAI.
The instructions deriving from BinOpAI were moved out of the "let Defs", and a
BinOpAI_FF class was created, for instructions that implicitly define and use
EFLAGS and the A-register (SBC, ADC).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182883 91177308-0d34-0410-b5e6-96231b3b80d8
FastISel was only enabled for iOS ARM and Thumb2, this patch enables it
for ARM (not Thumb2) on Linux and NaCl.
Thumb2 support needs a bit more work, mainly around register class
restrictions.
The patch punts to SelectionDAG when doing TLS relocation on non-Darwin
targets. I will fix this and other FastISel-to-SelectionDAG failures in
a separate patch.
The patch also forces FastISel to retain frame pointers: iOS always
keeps them for backtracking (so emitted code won't change because of
this), but Linux was getting much worse code that was incorrect when
using big frames (such as test-suite's lencod). I'll also fix this in a
later patch, it will probably require a peephole so that FastISel
doesn't rematerialize frame pointers back-to-back.
The test changes are straightforward, similar to:
http://lists.cs.uiuc.edu/pipermail/llvm-commits/Week-of-Mon-20130513/174279.html
They also add a vararg test that got dropped in that change.
I ran all of test-suite on A15 hardware with --optimize-option=-O0 and
all the tests pass.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182877 91177308-0d34-0410-b5e6-96231b3b80d8
Tidy up three places where the register class for ARM and Thumb wasn't
restrictive enough:
- No PC dest for reg-reg add/orr/sub.
- No PC dest for shifts.
- No PC or SP for Thumb2 reg-imm add.
I encountered this while combining FastISel with
-verify-machineinstrs. These instructions defined registers whose
classes weren't restrictive enough, and the uses failed
verification. They're also undefined in the ISA, or would produce code
that FastISel wouldn't want. This doesn't fix the register class
narrowing issue (where uses should restrict definitions), and isn't
thorough, but it's a small step in the right direction.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182863 91177308-0d34-0410-b5e6-96231b3b80d8
This patch solves the problem of numeric register values not being accepted:
../set_alias.s:1:11: error: expected valid expression after comma
.set r4,$4
^
The parsing of .set directive is changed and handling of symbols in code
as well to enable this feature.
The test example is added.
Patch by Vladimir Medic
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182807 91177308-0d34-0410-b5e6-96231b3b80d8
This patch adds support for the CRJ and CGRJ instructions. Support for
the immediate forms will be a separate patch.
The architecture has a large number of comparison instructions. I think
it's generally better to concentrate on using the "best" comparison
instruction first and foremost, then only use something like CRJ if
CR really was the natual choice of comparison instruction. The patch
therefore opportunistically converts separate CR and BRC instructions
into a single CRJ while emitting instructions in ISelLowering.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182764 91177308-0d34-0410-b5e6-96231b3b80d8
When -ffast-math is in effect (on Linux, at least), clang defines
__FINITE_MATH_ONLY__ > 0 when including <math.h>. This causes the
preprocessor to include <bits/math-finite.h>, which renames the sqrt functions.
For instance, "sqrt" is renamed as "__sqrt_finite".
This patch adds the 3 new names in such a way that they will be treated
as equivalent to their respective original names.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182739 91177308-0d34-0410-b5e6-96231b3b80d8
isConsecutiveLS is a slightly more general form of
SelectionDAG::isConsecutiveLoad. Aside from also handling stores, it also does
not assume equality of the chain operands is necessary. In the case of the PPC
backend, this chain condition is checked in a more general way by the
surrounding code.
Mostly, this part of the refactoring in preparation for supporting optimized
unaligned stores.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182723 91177308-0d34-0410-b5e6-96231b3b80d8
When expanding unaligned Altivec loads, we use the decremented offset trick to
prevent page faults. Unfortunately, if we have a sequence of consecutive
unaligned loads, this leads to suboptimal code generation because the 'extra'
load from the first unaligned load can be combined with the base load from the
second (but only if the decremented offset trick is not used for the first).
Search up and down the chain, through loads and token factors, looking for
consecutive loads, and if one is found, don't use the offset reduction trick.
These duplicate loads are later combined to yield the desired sequence (in the
future, we might want a more-powerful chain search, but that will require some
changes to allow the combiner routines to access the AA object).
This should complete the initial implementation of the optimized unaligned
Altivec load expansion. There is some refactoring that should be done, but
that will happen when the unaligned store expansion is added.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182719 91177308-0d34-0410-b5e6-96231b3b80d8
The lvsl permutation control instruction is a function only of the alignment of
the pointer operand (relative to the 16-byte natural alignment of Altivec
vectors). As a result, multiple lvsl intrinsics where the operands differ by a
multiple of 16 can be combined.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182708 91177308-0d34-0410-b5e6-96231b3b80d8
Change SelectionDAG::getXXXNode() interfaces as well as call sites of
these functions to pass in SDLoc instead of DebugLoc.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182703 91177308-0d34-0410-b5e6-96231b3b80d8
Altivec only directly supports aligned loads, but the loads have a strange
property: If given an unaligned address, they truncate the address to the next
lower aligned address, and load from there. This property, along with an extra
load and some special-purpose permutation-control instructions that generate
the appropriate permutations from the original unaligned address, allow
efficient lowering of aligned loads. This code uses the trick explained in the
Apple Velocity Engine optimization overview document to prevent the needed
extra load from possibly causing a page fault if the original address happens
to be aligned.
As noted in the FIXMEs, there are several additional optimizations that can be
performed to reduce the cost of these loads even more. These will be
implemented in future commits.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182691 91177308-0d34-0410-b5e6-96231b3b80d8
- Ressurect old MCDisassemble API to soften transition.
- Extend MCTargetDesc to set target specific symbolizer.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182688 91177308-0d34-0410-b5e6-96231b3b80d8
