mirror of
https://github.com/nippur72/Apple1_MiST.git
synced 2025-02-28 18:29:27 +00:00
162 lines
6.4 KiB
Verilog
162 lines
6.4 KiB
Verilog
//
|
|
// sdram.v
|
|
//
|
|
// sdram controller implementation for the MiST board
|
|
// http://code.google.com/p/mist-board/
|
|
//
|
|
// Copyright (c) 2013 Till Harbaum <till@harbaum.org>
|
|
//
|
|
// This source file is free software: you can redistribute it and/or modify
|
|
// it under the terms of the GNU General Public License as published
|
|
// by the Free Software Foundation, either version 3 of the License, or
|
|
// (at your option) any later version.
|
|
//
|
|
// This source file is distributed in the hope that it will be useful,
|
|
// but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
// GNU General Public License for more details.
|
|
//
|
|
// You should have received a copy of the GNU General Public License
|
|
// along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
//
|
|
|
|
module sdram (
|
|
|
|
// interface to the MT48LC16M16 chip
|
|
inout [15:0] sd_data, // 16 bit bidirectional data bus
|
|
output [12:0] sd_addr, // 13 bit multiplexed address bus for row/col select
|
|
output [1:0] sd_dqm, // two byte masks
|
|
output [1:0] sd_ba, // four banks
|
|
output sd_cs, // chip select
|
|
output sd_we, // write enable
|
|
output sd_ras, // row address select
|
|
output sd_cas, // columns address select
|
|
|
|
// cpu/chipset interface
|
|
input init, // init signal after FPGA config to initialize RAM
|
|
input clk, // sdram is accessed at up to 128MHz
|
|
input clkref, // reference clock to sync to
|
|
|
|
// input [2:0] q,
|
|
|
|
input [7:0] din, // data input from chipset/cpu
|
|
output [7:0] dout, // data output to chipset/cpu
|
|
input [24:0] addr, // 25 bit byte address
|
|
input oe, // cpu/chipset requests read
|
|
input we // cpu/chipset requests write
|
|
);
|
|
|
|
// ---------------------------------------------------------------------
|
|
// ------------------------ sdram configuration ------------------------
|
|
// ---------------------------------------------------------------------
|
|
// MODE is sent as address on reset = 2
|
|
// PRECHARGE_ADDR is sent as address on reset = 13
|
|
localparam RASCAS_DELAY = 3'd3; // tRCD>=20ns -> 2 cycles@64MHz
|
|
localparam BURST_LENGTH = 3'b000; // 000=none, 001=2, 010=4, 011=8
|
|
localparam ACCESS_TYPE = 1'b0; // 0=sequential, 1=interleaved
|
|
localparam CAS_LATENCY = 3'd2; // 2/3 allowed
|
|
localparam OP_MODE = 2'b00; // only 00 (standard operation) allowed
|
|
localparam NO_WRITE_BURST = 1'b1; // 0= write burst enabled, 1=only single access write
|
|
localparam MODE = { 3'b000, NO_WRITE_BURST, OP_MODE, CAS_LATENCY, ACCESS_TYPE, BURST_LENGTH};
|
|
localparam PRECHARGE_ADDR = 13'b0010000000000;
|
|
|
|
// ---------------------------------------------------------------------
|
|
// ------------------------ cycle state machine ------------------------
|
|
// ---------------------------------------------------------------------
|
|
|
|
// there are 8 states (0-7) tracked by "q"
|
|
|
|
localparam STATE_IDLE = 3'd0; // first state in cycle
|
|
localparam STATE_CMD_START = 3'd1; // state in which a new command can be started
|
|
localparam STATE_CMD_CONT = STATE_CMD_START+RASCAS_DELAY-3'd1; // 4 command can be continued
|
|
localparam STATE_LAST = 3'd7; // last state in cycle
|
|
|
|
reg [2:0] q /* synthesis noprune */;
|
|
|
|
always @(posedge clk) begin
|
|
// 32Mhz counter synchronous to 4 Mhz clock
|
|
// force counter to pass state 5->6 exactly after the rising edge of clkref
|
|
// since clkref is two clocks early
|
|
if(((q == 7) && ( clkref == 0)) ||
|
|
((q == 0) && ( clkref == 1)) ||
|
|
((q != 7) && (q != 0)))
|
|
q <= q + 3'd1;
|
|
end
|
|
|
|
|
|
// ---------------------------------------------------------------------
|
|
// --------------------------- startup/reset ---------------------------
|
|
// ---------------------------------------------------------------------
|
|
|
|
// wait 1ms (32 clkref cycles) after FPGA config is done before going
|
|
// into normal operation. Initialize the ram in the last 16 reset cycles (cycles 15-0)
|
|
reg [4:0] reset;
|
|
always @(posedge clk) begin
|
|
if(init) reset <= 5'h1f;
|
|
else if((q == STATE_LAST) && (reset != 0))
|
|
reset <= reset - 5'd1;
|
|
end
|
|
|
|
// ---------------------------------------------------------------------
|
|
// ------------------ generate ram control signals ---------------------
|
|
// ---------------------------------------------------------------------
|
|
|
|
// all possible commands
|
|
localparam CMD_INHIBIT = 4'b1111; // initial state
|
|
localparam CMD_NOP = 4'b0111; // (not used here)
|
|
localparam CMD_ACTIVE = 4'b0011; // command starts, done at STATE_IDLE
|
|
localparam CMD_READ = 4'b0101; // read commanddone, done at STATE_CMD_CONT
|
|
localparam CMD_WRITE = 4'b0100; // write command, done at STATE_CMD_CONT
|
|
localparam CMD_BURST_TERMINATE = 4'b0110; // (not used here)
|
|
localparam CMD_PRECHARGE = 4'b0010; // sends a precharge address, done when reset=13 and STATE_IDLE
|
|
localparam CMD_AUTO_REFRESH = 4'b0001; // refresh command, done at STATE_IDLE
|
|
localparam CMD_LOAD_MODE = 4'b0000; // sends MODE (sdram config), done when reset=2 and STATE_IDLE
|
|
|
|
reg [3:0] sd_cmd; // current command sent to sd ram
|
|
|
|
// drive control signals according to current command
|
|
assign sd_cs = sd_cmd[3]; // in negated logic
|
|
assign sd_ras = sd_cmd[2]; // in negated logic
|
|
assign sd_cas = sd_cmd[1]; // in negated logic
|
|
assign sd_we = sd_cmd[0]; // in negated logic
|
|
|
|
assign sd_data = we ? {din, din} : 16'bZZZZZZZZZZZZZZZZ;
|
|
|
|
assign dout = sd_data[7:0];
|
|
|
|
always @(posedge clk) begin
|
|
sd_cmd <= CMD_INHIBIT;
|
|
|
|
if(reset != 0) begin
|
|
// SDRAM is resetting, counting from 31 to 0
|
|
if(q == STATE_IDLE) begin
|
|
if(reset == 13) sd_cmd <= CMD_PRECHARGE;
|
|
if(reset == 2) sd_cmd <= CMD_LOAD_MODE;
|
|
end
|
|
end else begin
|
|
// normal run
|
|
if(q == STATE_IDLE) begin
|
|
if(we || oe) sd_cmd <= CMD_ACTIVE;
|
|
else sd_cmd <= CMD_AUTO_REFRESH;
|
|
end
|
|
else if(q == STATE_CMD_CONT) begin
|
|
if(we) sd_cmd <= CMD_WRITE;
|
|
else if(oe) sd_cmd <= CMD_READ;
|
|
end
|
|
end
|
|
end
|
|
|
|
// address during reset
|
|
wire [12:0] reset_addr = (reset == 13) ? PRECHARGE_ADDR : MODE;
|
|
|
|
// address during normal run
|
|
wire [12:0] row = addr[20:8];
|
|
wire [12:0] col = { 4'b0010, addr[23], addr[7:0] };
|
|
wire [12:0] run_addr = (q == STATE_CMD_START)? row : col;
|
|
|
|
assign sd_addr = (reset != 0) ? reset_addr : run_addr;
|
|
assign sd_ba = addr[22:21]; // bank is taken from cpu address high bits
|
|
assign sd_dqm = 2'b00; // no mask
|
|
|
|
endmodule
|