''*************************************** ''* PS/2 Keyboard Driver v1.0.1 * ''* Author: Chip Gracey * ''* Copyright (c) 2004 Parallax, Inc. * ''* See end of file for terms of use. * ''*************************************** {-----------------REVISION HISTORY----------------- v1.0.1 - Updated 6/15/2006 to work with Propeller Tool 0.96} VAR long cog long par_tail 'key buffer tail read/write (19 contiguous longs) long par_head 'key buffer head read-only long par_present 'keyboard present read-only long par_states[8] 'key states (256 bits) read-only long par_keys[8] 'key buffer (16 words) read-only (also used to pass initial parameters) PUB start(dpin, cpin) : okay '' Start keyboard driver - starts a cog '' returns false if no cog available '' '' dpin = data signal on PS/2 jack '' cpin = clock signal on PS/2 jack '' '' use 100-ohm resistors between pins and jack '' use 10K-ohm resistors to pull jack-side signals to VDD '' connect jack-power to 5V, jack-gnd to VSS '' '' all lock-keys will be enabled, NumLock will be initially 'on', '' and auto-repeat will be set to 15cps with a delay of .5s okay := startx(dpin, cpin, %0_000_100, %01_01000) PUB startx(dpin, cpin, locks, auto) : okay '' Like start, but allows you to specify lock settings and auto-repeat '' '' locks = lock setup '' bit 6 disallows shift-alphas (case set soley by CapsLock) '' bits 5..3 disallow toggle of NumLock/CapsLock/ScrollLock state '' bits 2..0 specify initial state of NumLock/CapsLock/ScrollLock '' (eg. %0_001_100 = disallow ScrollLock, NumLock initially 'on') '' '' auto = auto-repeat setup '' bits 6..5 specify delay (0=.25s, 1=.5s, 2=.75s, 3=1s) '' bits 4..0 specify repeat rate (0=30cps..31=2cps) '' (eg %01_00000 = .5s delay, 30cps repeat) stop longmove(@par_keys, @dpin, 4) okay := cog := cognew(@entry, @par_tail) + 1 PUB stop '' Stop keyboard driver - frees a cog if cog cogstop(cog~ - 1) longfill(@par_tail, 0, 19) PUB present : truefalse '' Check if keyboard present - valid ~2s after start '' returns t|f truefalse := -par_present PUB key : keycode '' Get key (never waits) '' returns key (0 if buffer empty) if par_tail <> par_head keycode := par_keys.word[par_tail] par_tail := ++par_tail & $F PUB getkey : keycode '' Get next key (may wait for keypress) '' returns key repeat until (keycode := key) PUB newkey : keycode '' Clear buffer and get new key (always waits for keypress) '' returns key par_tail := par_head keycode := getkey PUB gotkey : truefalse '' Check if any key in buffer '' returns t|f truefalse := par_tail <> par_head PUB clearkeys '' Clear key buffer par_tail := par_head PUB keystate(k) : state '' Get the state of a particular key '' returns t|f state := -(par_states[k >> 5] >> k & 1) DAT '****************************************** '* Assembly language PS/2 keyboard driver * '****************************************** org ' ' ' Entry ' entry movd :par,#_dpin 'load input parameters _dpin/_cpin/_locks/_auto mov x,par add x,#11*4 mov y,#4 :par rdlong 0,x add :par,dlsb add x,#4 djnz y,#:par mov dmask,#1 'set pin masks shl dmask,_dpin mov cmask,#1 shl cmask,_cpin test _dpin,#$20 wc 'modify port registers within code muxc _d1,dlsb muxc _d2,dlsb muxc _d3,#1 muxc _d4,#1 test _cpin,#$20 wc muxc _c1,dlsb muxc _c2,dlsb muxc _c3,#1 mov _head,#0 'reset output parameter _head ' ' ' Reset keyboard ' reset mov dira,#0 'reset directions mov dirb,#0 movd :par,#_present 'reset output parameters _present/_states[8] mov x,#1+8 :par mov 0,#0 add :par,dlsb djnz x,#:par mov stat,#8 'set reset flag ' ' ' Update parameters ' update movd :par,#_head 'update output parameters _head/_present/_states[8] mov x,par add x,#1*4 mov y,#1+1+8 :par wrlong 0,x add :par,dlsb add x,#4 djnz y,#:par test stat,#8 wc 'if reset flag, transmit reset command if_c mov data,#$FF if_c call #transmit ' ' ' Get scancode ' newcode mov stat,#0 'reset state :same call #receive 'receive byte from keyboard cmp data,#$83+1 wc 'scancode? if_nc cmp data,#$AA wz 'powerup/reset? if_nc_and_z jmp #configure if_nc cmp data,#$E0 wz 'extended? if_nc_and_z or stat,#1 if_nc_and_z jmp #:same if_nc cmp data,#$F0 wz 'released? if_nc_and_z or stat,#2 if_nc_and_z jmp #:same if_nc jmp #newcode 'unknown, ignore ' ' ' Translate scancode and enter into buffer ' test stat,#1 wc 'lookup code with extended flag rcl data,#1 call #look cmp data,#0 wz 'if unknown, ignore if_z jmp #newcode mov t,_states+6 'remember lock keys in _states mov x,data 'set/clear key bit in _states shr x,#5 add x,#_states movd :reg,x mov y,#1 shl y,data test stat,#2 wc :reg muxnc 0,y if_nc cmpsub data,#$F0 wc 'if released or shift/ctrl/alt/win, done if_c jmp #update mov y,_states+7 'get shift/ctrl/alt/win bit pairs shr y,#16 cmpsub data,#$E0 wc 'translate keypad, considering numlock if_c test _locks,#%100 wz if_c_and_z add data,#@keypad1-@table if_c_and_nz add data,#@keypad2-@table if_c call #look if_c jmp #:flags cmpsub data,#$DD wc 'handle scrlock/capslock/numlock if_c mov x,#%001_000 if_c shl x,data if_c andn x,_locks if_c shr x,#3 if_c shr t,#29 'ignore auto-repeat if_c andn x,t wz if_c xor _locks,x if_c add data,#$DD if_c_and_nz or stat,#4 'if change, set configure flag to update leds test y,#%11 wz 'get shift into nz if_nz cmp data,#$60+1 wc 'check shift1 if_nz_and_c cmpsub data,#$5B wc if_nz_and_c add data,#@shift1-@table if_nz_and_c call #look if_nz_and_c andn y,#%11 if_nz cmp data,#$3D+1 wc 'check shift2 if_nz_and_c cmpsub data,#$27 wc if_nz_and_c add data,#@shift2-@table if_nz_and_c call #look if_nz_and_c andn y,#%11 test _locks,#%010 wc 'check shift-alpha, considering capslock muxnc :shift,#$20 test _locks,#$40 wc if_nz_and_nc xor :shift,#$20 cmp data,#"z"+1 wc if_c cmpsub data,#"a" wc :shift if_c add data,#"A" if_c andn y,#%11 :flags ror data,#8 'add shift/ctrl/alt/win flags mov x,#4 '+$100 if shift :loop test y,#%11 wz '+$200 if ctrl shr y,#2 '+$400 if alt if_nz or data,#1 '+$800 if win ror data,#1 djnz x,#:loop rol data,#12 rdlong x,par 'if room in buffer and key valid, enter sub x,#1 and x,#$F cmp x,_head wz if_nz test data,#$FF wz if_nz mov x,par if_nz add x,#11*4 if_nz add x,_head if_nz add x,_head if_nz wrword data,x if_nz add _head,#1 if_nz and _head,#$F test stat,#4 wc 'if not configure flag, done if_nc jmp #update 'else configure to update leds ' ' ' Configure keyboard ' configure mov data,#$F3 'set keyboard auto-repeat call #transmit mov data,_auto and data,#%11_11111 call #transmit mov data,#$ED 'set keyboard lock-leds call #transmit mov data,_locks rev data,#-3 & $1F test data,#%100 wc rcl data,#1 and data,#%111 call #transmit mov x,_locks 'insert locks into _states and x,#%111 shl _states+7,#3 or _states+7,x ror _states+7,#3 mov _present,#1 'set _present jmp #update 'done ' ' ' Lookup byte in table ' look ror data,#2 'perform lookup movs :reg,data add :reg,#table shr data,#27 mov x,data :reg mov data,0 shr data,x jmp #rand 'isolate byte ' ' ' Transmit byte to keyboard ' transmit _c1 or dira,cmask 'pull clock low movs napshr,#13 'hold clock for ~128us (must be >100us) call #nap _d1 or dira,dmask 'pull data low movs napshr,#18 'hold data for ~4us call #nap _c2 xor dira,cmask 'release clock test data,#$0FF wc 'append parity and stop bits to byte muxnc data,#$100 or data,dlsb mov x,#10 'ready 10 bits transmit_bit call #wait_c0 'wait until clock low shr data,#1 wc 'output data bit _d2 muxnc dira,dmask mov wcond,c1 'wait until clock high call #wait djnz x,#transmit_bit 'another bit? mov wcond,c0d0 'wait until clock and data low call #wait mov wcond,c1d1 'wait until clock and data high call #wait call #receive_ack 'receive ack byte with timed wait cmp data,#$FA wz 'if ack error, reset keyboard if_nz jmp #reset transmit_ret ret ' ' ' Receive byte from keyboard ' receive test _cpin,#$20 wc 'wait indefinitely for initial clock low waitpne cmask,cmask receive_ack mov x,#11 'ready 11 bits receive_bit call #wait_c0 'wait until clock low movs napshr,#16 'pause ~16us call #nap _d3 test dmask,ina wc 'input data bit rcr data,#1 mov wcond,c1 'wait until clock high call #wait djnz x,#receive_bit 'another bit? shr data,#22 'align byte test data,#$1FF wc 'if parity error, reset keyboard if_nc jmp #reset rand and data,#$FF 'isolate byte look_ret receive_ack_ret receive_ret ret ' ' ' Wait for clock/data to be in required state(s) ' wait_c0 mov wcond,c0 '(wait until clock low) wait mov y,tenms 'set timeout to 10ms wloop movs napshr,#18 'nap ~4us call #nap _c3 test cmask,ina wc 'check required state(s) _d4 test dmask,ina wz 'loop until got state(s) or timeout wcond if_never djnz y,#wloop '(replaced with c0/c1/c0d0/c1d1) tjz y,#reset 'if timeout, reset keyboard wait_ret wait_c0_ret ret c0 if_c djnz y,#wloop '(if_never replacements) c1 if_nc djnz y,#wloop c0d0 if_c_or_nz djnz y,#wloop c1d1 if_nc_or_z djnz y,#wloop ' ' ' Nap ' nap rdlong t,#0 'get clkfreq napshr shr t,#18/16/13 'shr scales time min t,#3 'ensure waitcnt won't snag add t,cnt 'add cnt to time waitcnt t,#0 'wait until time elapses (nap) nap_ret ret ' ' ' Initialized data ' ' dlsb long 1 << 9 tenms long 10_000 / 4 ' ' ' Lookup table ' ascii scan extkey regkey ()=keypad ' table word $0000 '00 word $00D8 '01 F9 word $0000 '02 word $00D4 '03 F5 word $00D2 '04 F3 word $00D0 '05 F1 word $00D1 '06 F2 word $00DB '07 F12 word $0000 '08 word $00D9 '09 F10 word $00D7 '0A F8 word $00D5 '0B F6 word $00D3 '0C F4 word $0009 '0D Tab word $0060 '0E ` word $0000 '0F word $0000 '10 word $F5F4 '11 Alt-R Alt-L word $00F0 '12 Shift-L word $0000 '13 word $F3F2 '14 Ctrl-R Ctrl-L word $0071 '15 q word $0031 '16 1 word $0000 '17 word $0000 '18 word $0000 '19 word $007A '1A z word $0073 '1B s word $0061 '1C a word $0077 '1D w word $0032 '1E 2 word $F600 '1F Win-L word $0000 '20 word $0063 '21 c word $0078 '22 x word $0064 '23 d word $0065 '24 e word $0034 '25 4 word $0033 '26 3 word $F700 '27 Win-R word $0000 '28 word $0020 '29 Space word $0076 '2A v word $0066 '2B f word $0074 '2C t word $0072 '2D r word $0035 '2E 5 word $CC00 '2F Apps word $0000 '30 word $006E '31 n word $0062 '32 b word $0068 '33 h word $0067 '34 g word $0079 '35 y word $0036 '36 6 word $CD00 '37 Power word $0000 '38 word $0000 '39 word $006D '3A m word $006A '3B j word $0075 '3C u word $0037 '3D 7 word $0038 '3E 8 word $CE00 '3F Sleep word $0000 '40 word $002C '41 , word $006B '42 k word $0069 '43 i word $006F '44 o word $0030 '45 0 word $0039 '46 9 word $0000 '47 word $0000 '48 word $002E '49 . word $EF2F '4A (/) / word $006C '4B l word $003B '4C ; word $0070 '4D p word $002D '4E - word $0000 '4F word $0000 '50 word $0000 '51 word $0027 '52 ' word $0000 '53 word $005B '54 [ word $003D '55 = word $0000 '56 word $0000 '57 word $00DE '58 CapsLock word $00F1 '59 Shift-R word $EB0D '5A (Enter) Enter word $005D '5B ] word $0000 '5C word $005C '5D \ word $CF00 '5E WakeUp word $0000 '5F word $0000 '60 word $0000 '61 word $0000 '62 word $0000 '63 word $0000 '64 word $0000 '65 word $00C8 '66 BackSpace word $0000 '67 word $0000 '68 word $C5E1 '69 End (1) word $0000 '6A word $C0E4 '6B Left (4) word $C4E7 '6C Home (7) word $0000 '6D word $0000 '6E word $0000 '6F word $CAE0 '70 Insert (0) word $C9EA '71 Delete (.) word $C3E2 '72 Down (2) word $00E5 '73 (5) word $C1E6 '74 Right (6) word $C2E8 '75 Up (8) word $00CB '76 Esc word $00DF '77 NumLock word $00DA '78 F11 word $00EC '79 (+) word $C7E3 '7A PageDn (3) word $00ED '7B (-) word $DCEE '7C PrScr (*) word $C6E9 '7D PageUp (9) word $00DD '7E ScrLock word $0000 '7F word $0000 '80 word $0000 '81 word $0000 '82 word $00D6 '83 F7 keypad1 byte $CA, $C5, $C3, $C7, $C0, 0, $C1, $C4, $C2, $C6, $C9, $0D, "+-*/" keypad2 byte "0123456789.", $0D, "+-*/" shift1 byte "{|}", 0, 0, "~" shift2 byte $22, 0, 0, 0, 0, "<_>?)!@#$%^&*(", 0, ":", 0, "+" ' ' ' Uninitialized data ' dmask res 1 cmask res 1 stat res 1 data res 1 x res 1 y res 1 t res 1 _head res 1 'write-only _present res 1 'write-only _states res 8 'write-only _dpin res 1 'read-only at start _cpin res 1 'read-only at start _locks res 1 'read-only at start _auto res 1 'read-only at start '' '' '' _________ '' Key Codes '' '' 00..DF = keypress and keystate '' E0..FF = keystate only '' '' '' 09 Tab '' 0D Enter '' 20 Space '' 21 ! '' 22 " '' 23 # '' 24 $ '' 25 % '' 26 & '' 27 ' '' 28 ( '' 29 ) '' 2A * '' 2B + '' 2C , '' 2D - '' 2E . '' 2F / '' 30 0..9 '' 3A : '' 3B ; '' 3C < '' 3D = '' 3E > '' 3F ? '' 40 @ '' 41..5A A..Z '' 5B [ '' 5C \ '' 5D ] '' 5E ^ '' 5F _ '' 60 ` '' 61..7A a..z '' 7B { '' 7C | '' 7D } '' 7E ~ '' '' 80-BF (future international character support) '' '' C0 Left Arrow '' C1 Right Arrow '' C2 Up Arrow '' C3 Down Arrow '' C4 Home '' C5 End '' C6 Page Up '' C7 Page Down '' C8 Backspace '' C9 Delete '' CA Insert '' CB Esc '' CC Apps '' CD Power '' CE Sleep '' CF Wakeup '' '' D0..DB F1..F12 '' DC Print Screen '' DD Scroll Lock '' DE Caps Lock '' DF Num Lock '' '' E0..E9 Keypad 0..9 '' EA Keypad . '' EB Keypad Enter '' EC Keypad + '' ED Keypad - '' EE Keypad * '' EF Keypad / '' '' F0 Left Shift '' F1 Right Shift '' F2 Left Ctrl '' F3 Right Ctrl '' F4 Left Alt '' F5 Right Alt '' F6 Left Win '' F7 Right Win '' '' FD Scroll Lock State '' FE Caps Lock State '' FF Num Lock State '' '' +100 if Shift '' +200 if Ctrl '' +400 if Alt '' +800 if Win '' '' eg. Ctrl-Alt-Delete = $6C9 '' '' '' Note: Driver will buffer up to 15 keystrokes, then ignore overflow. {{ ┌──────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────┐ │ TERMS OF USE: MIT License │ ├──────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────┤ │Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation │ │files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, │ │modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software│ │is furnished to do so, subject to the following conditions: │ │ │ │The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.│ │ │ │THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE │ │WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR │ │COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, │ │ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. │ └──────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────┘ }}