Apple2-IO-RPi/Apple2/DriveFirmware.asm
Terence Boldt aa5910cee8
Initial Pico hardware support
* Added assemble.cmd for Windows.

In the long run, some (c)make-based cross-plafrom solution seems preferable.

* Fill up the menu page just like the other pages.

* Allow to assemble for different hardware types.

The first script parameter is used to set the ca65 symbol HW_TYPE. Without parameter, HW_TYPE is set to 0.

* Avoid unwanted i/o access.

Depending on the 6502, LDA addr,X and/or STA addr,X produce additional phantom reads. In order to avoid those phantom reads to do i/o access, I used the "classic" approach of moving those reads from page $C0 to page $BF.

* Made use of BIT instruction to access InputFlags from firmware.

Doing the same for access from disk-based software would require selfmodifying code as there's not bit <addr>,x instruction.

* Removed push/pop from GetByte.

After the replacing the rol instructions with bit instructions with a recent chnage, the only reason left to save a to the stack was setting the OutputFlags. But that can be done using x.

* Added InputFlags check for consistency.

* Added support for an alternative hardware type.

The new hardware type has simple UART-type interface. Beside the two data registers, there are only the two bits to indicate readability and writability of the data registers.

* Added another comminucation interface implementation.

Use ACM CDC (or another proprietary) USB serial device for communication.

Currently VID / PID of a Raspberry Pi Pico SDK CDC UART are hardcoded - see https://github.com/raspberrypi/usb-pid

* Revert "Avoid unwanted i/o access."

Neither the original hardware type nor the alternative hardware type have any read and write i/o port share addresses. Therefore phantom reads aren't an issue with those hardware types.

This reverts commit ae5cb754fb.

* Adapt to the different error signatures on Linux.

So far the code was only tested on Windows.

* Added implementation of the alternative hardware type.

The implemenation is based on a Raspberry Pi Pico - see https://github.com/a2retrosystems/A2retroNET

The new hardware type has a simple UART-type interface. Beside the two data registers, there are only the two bits to indicate readability and writability of the data registers.

* Modify the HD image for the alternative hardware type.

It is likely desirable to have two HD images for the two hardware types. And likely the apple2driver program should default to the right one based on its protocol setting. BUt given that the HD image(s) shouldn't be part of the actual Git repo anyhow, I don't do anything about this here and now.

* Fixed shell startup (?)

At least on the alternative hardware, this "blindly sending" a reset command causes the shell to be terminated right away:
The driver acknowldges the reset command with a zero byte - and that byte ends up being read by DumpOutput causing it to branch to endOutput.

Maybe that sending a reset command is beneficial on the original hardware. Then another .if is required. Or DumpOutput shouldn't quit on reading a zero byte - the shell handler doesn't seem to send it on purpose(?)

* Upate HD image with recent shell change.

* Fix shell shutdown (?)

At least on the alternative hardware, things happen this way:
1. The shell 'exit' command has ptyOut signal outputComplete and terminate. At this point, ptyIn is still blocked up to one second in ReadCharacter - and can therefore not react on outputComplete.
2. The outputComplete handler in ShellCommand sends a zero byte. This makes on the A2 DumpOutput return and the caller send a zero byte. ShellCommand must not return here as ptyIn is still blocked.
3. The zero byte from the A2 has ptyIn return from ReadCharacter, signal userCancelled and terminate.
4. ShellCommand can now return, but it must not send a zero byte, as the A2 is not expecting it - and will therefore later misinterpret it.

Maybe the original hardware needs another handling, then differentiation of behavior in shell.go becomes necessary.

* Moved boot text out of IIgs copyright message area.

Having the boot text start at the left border of the third line makes it look nice on the cold boot screen of all Apple II's - and there's where the user sees it for some time while waiting for the RPi to come up.

* Several adjustements:

- Get latest Go version as of now.
- Nowadays (?) GitHub 'git clone' seems to only work with a GitHub account. Therefore the zip download workaround. The becomes hopefully unnecessary soon with Go module magic.
- Use 'go mod tidy' to update .sum file for now.
- Error handling for an empty drive 2 is currently not exactly great, so download Total Replay for drive 2. Unfortunately there's no stable URL as of now.
- Use $USER and $HOME instead of hardcoded values.
- Removed deprecated syslog output directives.

* Added brief fork description.

* Added ProDOS-Utilities reference.

* Reverted back to using 'git clone'.

I've no idea why git acted up the other day :-( Now, everything is back to normal...

* Ignore Pico build directory.

* Updated from https://github.com/a2retrosystems/A2retroNET

* Updated from https://github.com/a2retrosystems/A2retroNET

At this point, nothing at all is done on an A2 reset. This can likely be improved. However, Apple2-IO-RPi doesn't seem to handle A2 reset exactly gracefully anyhow.

In general, it seems desirable to introduce some simple framing protocol - like SLIP - that allows to recover from an A2 reset in the middle of an Apple2-IO-RPi command execution.

Such a framing protocol would allow to introduce different frame types. One frame type could then be an A2 reset frame sent by the A2retroNET firmware.

* Make use of brand new stable Total Replay download URL.

Thanks to 4am :-)

* Fixed typos.

* Clone upstream ProDOS-Utilities.

My ProDOS-Utilities pull request was merged.

* Added support for boards without LED.

* Updated link.

* Adjusted to the current A2retroNET hardware.

* Removed support for the Pico W.

* Updated URL.

* Updated URL.

* Make use A2Pico library.

* Added link to A2Pico.

* Remove intermediates from repo.

* Build intermediates from Pico build.

* Have LED reflect status of logic ACM connection.

* Update upstream repo references.

* Adjust build instructions.

* Update README.md

* Fix build and update dependencies

* Fix binary comparison

* Fix firware bug on classic hardware

---------

Co-authored-by: Oliver Schmidt <ol.sc@web.de>
2024-02-05 22:49:09 -05:00

207 lines
3.8 KiB
NASM

; Copyright Terence J. Boldt (c)2020-2024
; Use of this source code is governed by an MIT
; license that can be found in the LICENSE file.
; This file contains the source for the firmware
; that allows the Apple II to boot from the card
; and for ProDOS to recognize the card as two
; hard drivers
;ProDOS Zero Page
Command = $42 ;ProDOS Command
Unit = $43 ;ProDOS unit (SDDD0000)
BufferLo = $44
BufferHi = $45
BlockLo = $46
BlockHi = $47
; ProDOS Error Codes
IOError = $27
NoDevice = $28
WriteProtect = $2B
InputByte = $c08e+SLOT*$10
OutputByte = $c08d+SLOT*$10
InputFlags = $c08b+SLOT*$10
OutputFlags = $c087+SLOT*$10
ReadBlockCommand = $01
WriteBlockCommand = $02
GetTimeCommand = $03
ChangeDriveCommand = $04
ExecCommand = $05
LoadFileCommand = $06
SaveFileCommand = $07
MenuCommand = $08
.org SLOT*$100 + $C000
;ID bytes for booting and drive detection
cpx #$20 ;ID bytes for ProDOS and the
cpx #$00 ; Apple Autostart ROM
cpx #$03 ;
ldx #SLOT*$10
stx $2b
stx Unit
;force EPROM to second page on boot
lda #$3f ;set all flags high and page 3 of EPROM for menu
PageJump:
sta OutputFlags
jmp Start ;this jump is only called if coming in from PageJump with A=$0f
;entry points for ProDOS
DriverEntry:
lda #$0f ;set all flags high and page 0 of EPROM
sta OutputFlags
jmp Driver
;load first two blocks and execute to boot
Start:
lda #$01 ;set read command
sta Command
lda #$00 ;block 0
sta BlockLo
sta BlockHi
sta BufferLo ;buffer at $800
lda #$08
sta BufferHi
jsr Driver ;get the block
jmp $801 ;execute the block
; ProDOS Driver code
; First check that this is the right drive
Driver:
ldx Unit
lda Command; Check which command is being requested
beq GetStatus ;0 = Status command
cmp #ReadBlockCommand
beq ReadBlockAndSetTime
cmp #WriteBlockCommand
beq WriteBlock
sec ;set carry as we don't support any other commands
lda #$53 ;Invalid parameter error
rts
; ProDOS Status Command Handler
GetStatus:
ldx #$ff ;low byte number of blocks
ldy #$ff ;high byte number of blocks
lda #$0 ;zero accumulator and clear carry for success
clc
rts
; ProDOS Read Block Command
ReadBlockAndSetTime:
lda BlockHi ; only get the time if block 0002
bne readBlock
lda BlockLo
cmp #$02
bne readBlock
ldy #$00 ;Get the current time on each block read for now
lda #GetTimeCommand
jsr SendByte
getTimeByte:
jsr GetByte
sta $bf90,y
iny
cpy #$04
bne getTimeByte
readBlock:
lda #ReadBlockCommand ;read the block after setting the clock
jsr SendByte
lda BlockLo
jsr SendByte
lda BlockHi
jsr SendByte
txa
jsr SendByte
ldy #$0
jsr read256
inc BufferHi
jsr read256
dec BufferHi
lda #$0 ;zero accumulator and clear carry for success
clc
rts
read256:
jsr GetByte
sta (BufferLo),y
iny
bne read256
rts
; ProDOS Write Block Command
WriteBlock:
lda #WriteBlockCommand
jsr SendByte
lda BlockLo
jsr SendByte
lda BlockHi
jsr SendByte
txa
jsr SendByte
ldy #$0
jsr write256
inc BufferHi
jsr write256
dec BufferHi
lda #$0 ;zero accumulator and clear carry for success
clc
rts
write256:
lda (BufferLo),y
jsr SendByte
iny
bne write256
rts
SendByte:
bit InputFlags
bvs SendByte
sta OutputByte
.if HW_TYPE = 0
lda #$0e ; set bit 0 low to indicate write started
sta OutputFlags
finishWrite:
bit InputFlags
bvc finishWrite
lda #$0f
sta OutputFlags
.endif
rts
GetByte:
.if HW_TYPE = 0
lda #$0d ;set read flag low
sta OutputFlags
.endif
waitRead:
bit InputFlags
bmi waitRead
lda InputByte
.if HW_TYPE = 0
pha
lda #$0f ;set all flags high
sta OutputFlags
finishRead:
bit InputFlags
bpl finishRead
pla
.endif
end:
rts
.repeat 251-<end
.byte 0
.endrepeat
.byte 0,0 ;0000 blocks = check status
.byte 23 ;bit set(0=status 1=read 2=write) unset(3=format, 4/5=number of volumes, 6=interruptable, 7=removable)
.byte DriverEntry&$00FF ;low byte of entry