mirror of
https://github.com/ThorstenBr/FloppyEmuDiskIIEnclosure.git
synced 2024-11-22 13:32:52 +00:00
4c5e315a05
which provides much better stability. The strain-relief is angled, so the bracket can still be attached and screwed when the top shell and base board are glued.
59 lines
2.4 KiB
OpenSCAD
59 lines
2.4 KiB
OpenSCAD
// Copyright 2022 Thorsten Brehm
|
|
// brehmt (at) gmail dot com
|
|
|
|
// rear panel
|
|
module makeRear()
|
|
{
|
|
Width = BoxX_Width-2*RearWallGap;
|
|
difference()
|
|
{
|
|
translate([RearWallGap, 0, BoxZ_Depth-RearWallZOffset-RearWallZLedge])
|
|
rotate([90, 0, 90])
|
|
{
|
|
difference()
|
|
{
|
|
roundedCube(BoxY_Height, RearWallZLedge, Width, Box_Corner_Radius);
|
|
translate([SKIN, -SKIN, 0]) roundedCube(BoxY_Height, RearWallZLedge, Width, Box_Corner_Radius);
|
|
translate([BoxY_Height-RearWallGap-RearWallCableGapHeight,RearWallZLedge-SKIN*2,0])
|
|
cube([RearWallCableGapHeight+10, SKIN*2, Width]);
|
|
}
|
|
}
|
|
|
|
// hole
|
|
translate([FrontGapX/2, -SKIN , BoxZ_Depth-RearWallZOffset-RearWallZLedge/2]) rotate([270, 0, 0])
|
|
hole(ScrewDiameter, 10);
|
|
|
|
// hole
|
|
translate([BoxX_Width-FrontGapX/2, -SKIN , BoxZ_Depth-RearWallZOffset-RearWallZLedge/2]) rotate([270, 0, 0])
|
|
hole(ScrewDiameter, 10);
|
|
}
|
|
|
|
// long edge, top of rear wall
|
|
translate([RearWallGap, BoxY_Height-RearWallGap-RearWallCableGapHeight-5, BoxZ_Depth-RearWallZOffset-SKIN])
|
|
roundedCube(BoxX_Width-RearWallCableGapWidth-RearWallCableGapXOffset, RearWallCableGapHeight+5, SKIN, Box_Corner_Radius);
|
|
|
|
// short edge, top of rear wall
|
|
translate([BoxX_Width-RearWallGap-RearWallCableGapXOffset, BoxY_Height-RearWallGap-RearWallCableGapHeight-5, BoxZ_Depth-RearWallZOffset-SKIN])
|
|
roundedCube(RearWallCableGapXOffset, RearWallCableGapHeight+5, SKIN, Box_Corner_Radius);
|
|
|
|
// screw posts
|
|
translate([FrontGapX/2, SKIN , BoxZ_Depth-RearWallZOffset-RearWallZLedge/2]) rotate([270, 0, 0])
|
|
screwPost(ScrewPostHeight, ScrewPostDiameter, ScrewDiameter, ScrewPostHeight, ScrewPostFillet);
|
|
|
|
translate([BoxX_Width-FrontGapX/2, SKIN , BoxZ_Depth-RearWallZOffset-RearWallZLedge/2]) rotate([270, 0, 0])
|
|
screwPost(ScrewPostHeight, ScrewPostDiameter, ScrewDiameter, ScrewPostHeight, ScrewPostFillet);
|
|
|
|
// support triangles for stability
|
|
SupportWidth = RearWallZLedge-SKIN*2;
|
|
// left
|
|
translate([RearWallGap+Box_Corner_Radius, SKIN, BoxZ_Depth-RearWallZOffset-SupportWidth-SKIN])
|
|
rotate([270, 180, 0]) prism(SKIN, SupportWidth, SupportWidth);
|
|
// right
|
|
translate([BoxX_Width-Box_Corner_Radius-SKIN, SKIN, BoxZ_Depth-RearWallZOffset-SupportWidth-SKIN])
|
|
rotate([270, 180, 0]) prism(SKIN, SupportWidth, SupportWidth);
|
|
// center
|
|
translate([(BoxX_Width-Box_Corner_Radius-SKIN)/2, SKIN, BoxZ_Depth-RearWallZOffset-SupportWidth-SKIN])
|
|
rotate([270, 180, 0]) prism(SKIN, SupportWidth, SupportWidth);
|
|
}
|
|
|