mirror of
https://github.com/TomNisbet/TommyPROM.git
synced 2024-12-21 18:30:09 +00:00
update chip driver docs
This commit is contained in:
Tom Nisbet
parent
d8baefaaf4
commit
dbaef539b0
@ -27,19 +27,21 @@ enable and disable Software Data Protection, but uses a direct write for program
|
||||
TommyPROM has a variety of PromDevice Modules that can be compiled in to support these
|
||||
different chip technologies.
|
||||
|
||||
|
||||
# Verified Chips
|
||||
|
||||
|Model |Manufacturer |Type |Module |Notes|
|
||||
|:--- |:--- |:--- |:--- |:--- |
|
||||
|AT28C256 |Atmel, others|EEPROM |28C |Fully supported|
|
||||
|AT28C64 |Atmel, others|EEPROM |28C |Fully supported|
|
||||
|AT29C010 |Atmel |Flash |28C |Only with 128 byte or less sector size|
|
||||
|SST39SF040|Microchip |Flash |SST39SF|All SST39SF0x0 supported|
|
||||
|SST28SF040|SST |Flash |SST28SF|All SST28SF0x0 supported|
|
||||
|SST27SF020|SST |Flash |27 |12V continuous for pgm/erase|
|
||||
|W27C257 |Winbond |EEPROM |27 |Continual 12V or 14V for program/erase|
|
||||
|AT29C010 |Atmel |Flash |28C |Only with 128 byte or less sector size|
|
||||
|W27C257 |Winbond |EEPROM |27 |Continuous 12V or 14V for program/erase|
|
||||
|8755A |Intel |EPROM |8755A |Requires 25V pulses to program|
|
||||
|
||||
|
||||
# PromDevice Modules
|
||||
|
||||
This PromDevice28C module is enabled by default to program 28C256 EEPROMS. To use a
|
||||
@ -57,27 +59,15 @@ commands to enable and disable the [Software Data protection (SDP)](28C256-notes
|
||||
features of 28C chips. There is also support for the fast block write mode of these
|
||||
chips, allowing a 32KB chip to be programmed in just a few seconds.
|
||||
|
||||
## PromDevice27
|
||||
|
||||
The 27C EPROMs use a variety of programming algorithms. Code exists for some of these,
|
||||
but very few of the chips have been tested.
|
||||
|
||||
Most, if not all, 27C series chips are not 5V only and require a higher voltage to program
|
||||
them. Some need the voltage constantly applied while programming and others use high
|
||||
voltage pulses for each byte. For constant voltage chips, it is probably easiest to just
|
||||
add an external power supply and manually assert the voltage before starting a write. For
|
||||
those with switched voltages, some elements of the 8755 hardware may be leveraged to build
|
||||
a version of the programmer that supports these chips.
|
||||
|
||||
## PromDeviceSST39SF
|
||||
|
||||
The SST39SF0x0 NOR Flash chips use fixed 4KB sectors that must be manually erased before a new program
|
||||
operation, but the code manages this transparently. Whenever a write is started to a new
|
||||
segment, the driver first initiates an erase of that sector. A second write to the same
|
||||
sector will not cause an erase, so it is possible to write to a segment multiple times
|
||||
with no additional steps as long as the writes are to different parts of the sector. For
|
||||
example, 256 bytes could be written to the start of a sector from one file and then 512
|
||||
bytes could be written to the end of the sector from another file.
|
||||
The SST39SF0x0 NOR Flash chips use fixed 4KB sectors that must be manually erased before a
|
||||
new program operation, but the code manages this transparently. Whenever a write is
|
||||
started to a new segment, the driver first initiates an erase of that sector. A second
|
||||
write to the same sector will not cause an erase, so it is possible to write to a segment
|
||||
multiple times with no additional steps as long as the writes are to different parts of
|
||||
the sector. For example, 256 bytes could be written to the start of a sector from one
|
||||
file and then 512 bytes could be written to the end of the sector from another file.
|
||||
|
||||
Writing data that spans multiple sectors also works with no additional steps. When
|
||||
a sector boundary is crossed, the new sector is erased and set as the current sector.
|
||||
@ -97,6 +87,24 @@ the 28SF are slower.
|
||||
|
||||
All programming and erase operations for the 28SF chips require only a single 5V power supply.
|
||||
|
||||
## PromDevice27
|
||||
|
||||
The 27C supports Flash, EEPROM, and EPROM chips that use a variety of programming algorithms.
|
||||
|
||||
Most, if not all, 27C series chips are not 5V-only and require a higher voltage to program
|
||||
or erase. This driver supports chips that need the voltage constantly applied while
|
||||
programming or erasing. The programming voltages are provided by an external power supply
|
||||
and manually switched before starting a write or erase operation. See the [TommyPROM32
|
||||
hardware](pcb#TommyPROM32) for a diode circuit that allows the programming voltage to be
|
||||
switched between Vcc and a higher voltage.
|
||||
|
||||
Check the [Chip Details](#27c-and-27e-series-eproms-and-flash) for the high voltage
|
||||
connections for a particular chip or consult your data sheet.
|
||||
|
||||
Chips that use high voltage pulses for each byte are not supported. For those chips, some
|
||||
elements of the [8755A hardware](8755A-hardware) may be leveraged to build a version of
|
||||
the programmer that is able to provide high voltage pulses.
|
||||
|
||||
## PromDevice8755
|
||||
|
||||
TommyPROM has a driver for Intel 8755 EPROMs. This driver replaces the 28C driver at
|
||||
@ -117,7 +125,6 @@ need for shift registers to create address lines.
|
||||
The 8755 build of TommyPROM also has a circuit to control the 25V programming pulses.
|
||||
|
||||
|
||||
|
||||
# Chip Details
|
||||
|
||||
## 28C Series 28C256
|
||||
@ -149,6 +156,32 @@ This is an earlier version of the SST39SF series chips. They are pin compatible
|
||||
flash chips support software data protection. The _Lock_ and _Unlock_ commands can be
|
||||
used to enable and disable SDP from the command line.
|
||||
|
||||
## 27C and 27E Series EPROMs and Flash
|
||||
|
||||
### W27C257 and W27C512
|
||||
|
||||
The Winbond W27C257 and W27E257 appear to be identical 32Kx8 EEPROMs. The 27C version
|
||||
has been tested. The Winbond W27C512 is a 64Kx8 EEPROM with no dedicated _VPP_ pin.
|
||||
|
||||
The 257 EEPROMs have a _VPP_ pin that needs a constant 12V during programming. Unlike the
|
||||
newer 28C EEPROMs, these chips do not automatically erase before writing to a location.
|
||||
Instead, the entire chip is erased by applying 14V to _VPP_ and _A9_ and then pulsing
|
||||
_CE_.
|
||||
|
||||
Unlike the 257 chips, the W27C512 does not have a dedicated pin for the programming
|
||||
voltage and instead uses the OE pin to place the chip in programming mode. The verify
|
||||
operation requires that the OE pin be switched to _LOW_ and there is no hardware support
|
||||
for this, so the current code supports the 512 chip by doing a single write cycle with no
|
||||
verify.
|
||||
|
||||
Because the chips use a constant high voltage for programming instead of a pulse, an
|
||||
external power supply and two diodes can be used to supply either 5V or 12V to the
|
||||
pins for programming and erasing.
|
||||
|
||||
Note that the W27x257 chip are almost a drop-in replacement for the 28C256. The _WE_,
|
||||
_VPP_, and _A14_ pins are the only differences. For reading, the _VPP_ pin should be
|
||||
connected to 5V.
|
||||
|
||||
## 29C Series
|
||||
|
||||
The 29C0x0 chips are 5V sectored flash chips. They are similar to the 28C EEPROMs,
|
||||
@ -187,7 +220,6 @@ data. Data is written a byte at a time using a command register to control the
|
||||
programming. TommyPROM does not currently support 29F chips, but it would not be
|
||||
difficult to write a driver. The default 28C driver will read 29F chips.
|
||||
|
||||
|
||||
## SST27SF020
|
||||
|
||||
The Silicon Storage SST27SF0x0 are programmed similarly to the 27C257 in that a constant
|
||||
@ -200,31 +232,6 @@ the newer 28C EEPROMs, these chips do not automatically erase before writing to
|
||||
location. Instead, the entire chip is erased by applying 12V to _VPP_ and _A9_ and then
|
||||
pulsing _WE_.
|
||||
|
||||
## 27C and 27E Series EPROMs and flash
|
||||
|
||||
#### W27C257 and W27C512
|
||||
|
||||
The Winbond W27C257 and W27E257 appear to be identical 32Kx8 EEPROMs. The 27C version
|
||||
has been tested. The Winbond W27C512 is a 64Kx8 EEPROM with no dedicated _VPP_ pin.
|
||||
|
||||
The 257 EEPROMs have a _VPP_ pin that needs a constant 12V during programming. Unlike the
|
||||
newer 28C EEPROMs, these chips do not automatically erase before writing to a location.
|
||||
Instead, the entire chip is erased by applying 14V to _VPP_ and _A9_ and then pulsing
|
||||
_CE_.
|
||||
|
||||
Unlike the 257 chips, the W27C512 does not have a dedicated pin for the programming
|
||||
voltage and instead uses the OE pin to place the chip in programming mode. The verify
|
||||
operation requires that the OE pin be switched to _LOW_ and there is no hardware support
|
||||
for this, so the current code supports the 512 chip by doing a single write cycle with no
|
||||
verify.
|
||||
|
||||
Because the chips use a constant high voltage for programming instead of a pulse, an
|
||||
external power supply and two diodes can be used to supply either 5V or 12V to the
|
||||
pins for programming and erasing.
|
||||
|
||||
Note that the W27x257 chip are almost a drop-in replacement for the 28C256. The _WE_,
|
||||
_VPP_, and _A14_ pins are the only differences. For reading, the _VPP_ pin should be
|
||||
connected to 5V.
|
||||
|
||||
# Chips to be Tested
|
||||
|
||||
@ -234,12 +241,13 @@ connected to 5V.
|
||||
|W27C512 |Winbond |EEPROM |27 |Continual 12V or 14V for program/erase,VPP on OE|
|
||||
|AM28F512 |AMD |EEPROM | ||
|
||||
|AM29F040 |AMD |EEPROM | ||
|
||||
|AMS29AF010| | | ||
|
||||
|AMS29AF010|AMS | | ||
|
||||
|
||||
|
||||
# Chip Manufacturers
|
||||
|
||||
|Name |Code |Notes|
|
||||
|:--- |:--- |:--- |
|
||||
|:--- |:---|:---|
|
||||
|AMS - Advanced Memory Systems|AMS |Merged with Intersil|
|
||||
|AMD - Advanced Micro Devices |AM ||
|
||||
|Atmel |AT |Aquired by Microchip|
|
||||
|
||||
Loading…
Reference in New Issue
Block a user