add prom-specific doc page
This commit is contained in:
Tom Nisbet
parent
03fb322c0d
commit
e0fce3c3cd
|
|
@ -16,6 +16,8 @@ docs:
|
|||
url: /docs/hardware
|
||||
- title: "Software"
|
||||
url: /docs/software
|
||||
- title: "PROM-specific Code"
|
||||
url: /docs/prom-specific-code
|
||||
- title: "Printed Circuit Board"
|
||||
url: /docs/pcb
|
||||
- title: "Adding Chip Families"
|
||||
|
|
|
|||
|
|
@ -0,0 +1,217 @@
|
|||
---
|
||||
title: Chips Supported
|
||||
permalink: /docs/supported-chips
|
||||
exerpt: "PROM types supported by TommyPROM - EPROM, EEPROM, Flash"
|
||||
---
|
||||
|
||||
TommyPROM can be used to read and write several different types of PROM chips. Due to
|
||||
differences in the technologies of these chips, some features of TommyPROM may work
|
||||
differently or may not be applicable at all. The standard code can read most types of
|
||||
PROM, even if there is no specific software support for them.
|
||||
|
||||
# PromDevice Drivers
|
||||
|
||||
## PromDevice28C
|
||||
|
||||
The 28C series EEPROMs, specifically the 28C256, are the original chips that TommyPROM
|
||||
supported. As a result, these have the best support, with all of the interactive features
|
||||
of the command line. In addition the basic read and write operations, there are also
|
||||
commands to enable and disable the [Software Data protection (SDP)](28C256-notes)
|
||||
features of 28C chips. There is also support for the fast block write mode of these
|
||||
chips, allowing a 32KB chip to be programmed in just a few seconds.
|
||||
|
||||
## PromDevice27
|
||||
|
||||
The 27C EPROMs use a variety of programming algorithms. Code exists for some of these,
|
||||
but very few of the chips have been tested.
|
||||
|
||||
Most, if not all, 27C series chips are not 5V only and require a higher voltage to program
|
||||
them. Some need the voltage constantly applied while programming and others use high
|
||||
voltage pulses for each byte. For constant voltage chips, it is probably easiest to just
|
||||
add an external power supply and manually assert the voltage before starting a write. For
|
||||
those with switched voltages, some elements of the 8755 hardware may be leveraged to build
|
||||
a version of the programer that supports these chips.
|
||||
|
||||
## PromDeviceSST39SF
|
||||
|
||||
TommyPROM has a driver for Atmel SST39SF NOR flash chips. This driver replaces the 28C
|
||||
driver at compile time. See configure.h to enable a different driver.
|
||||
|
||||
The SST39SF chips use fixed 4KB sectors that must be manually erased before a new program
|
||||
operation, but the code manages this transparently. Whenever a write is started to a new
|
||||
segment, the driver first initiates an erase of that sector. A second write to the same
|
||||
sector will not cause an erase, so it is possible to write to a segment multiple times
|
||||
with no additional steps as long as the writes are to different parts of the sector. For
|
||||
example, 256 bytes could be written to the start of a sector from one file and then 512
|
||||
bytes could be written to the end of the sector from another file.
|
||||
|
||||
Writing data that spans multiple sectors also works with no additional steps. When
|
||||
a sector boundary is crossed, the new sector is erased and set as the current sector.
|
||||
|
||||
The SST39SF driver supports a manual erase from the command line using the E command.
|
||||
This is only needed if data will be rewritten to the same location after a previous write
|
||||
to that sector.
|
||||
|
||||
All programming and erase operations for the 39SF chips require only a single 5V power supply.
|
||||
|
||||
## PromDeviceSST39SF
|
||||
|
||||
The SST28SF0x0 SuperFlash chips are an earlier version of the 39SF chips, using 256-byte
|
||||
sectors. The 28SF and 39SF chips are pin compatible, but use different command sets for
|
||||
programming and erasing. For read-only applications, they should be identical, although
|
||||
the 28SF are slower.
|
||||
|
||||
All programming and erase operations for the 28SF chips require only a single 5V power supply.
|
||||
|
||||
## PromDevice8755
|
||||
|
||||
TommyPROM has a driver for Intel 8755 EPROMs. This driver replaces the 28C driver at
|
||||
compile time. See configure.h to enable a different driver. This driver will also read
|
||||
Intel 8355 OTP EPROMs. Also note that the TommyPROM hardware for the 8755 is drastically
|
||||
different from the other versions.
|
||||
|
||||
The Intel 8755 is a peripheral chip designed for 8085 systems. It is a 40 pin device that
|
||||
contains a 2KB EPROM plus two general-purpose I/O ports. The 8355 is a one-time
|
||||
programmable version of the 8755. The 8755 requires a 25V programming pulse for each byte
|
||||
to be written.
|
||||
|
||||
A new hardware build was created to support the 8755 chips. Because the 8755 has a multiplexed data and address bus, the usual shift registers are not used for addressing.
|
||||
The chip only needs 8 connects that are shared for address and data, plus three dedicated
|
||||
address lines. The Arduino has enough pins to drive all of these directly, without the
|
||||
need for shift registers to create address lines.
|
||||
|
||||
The 8755 build of TommyPROM also has a circuit to control the 25V programming pulses.
|
||||
|
||||
# Verified Chips
|
||||
|
||||
|Model |Manufacturer |Type |Module |Notes|
|
||||
|:--- |:--- |:--- |:--- |:--- |
|
||||
|AT28C256 |Atmel, others|EEPROM |28C |Fully supported|
|
||||
|SST39SF040|Microchip |Flash |SST39SF|All SST39SF0x0 supported|
|
||||
|SST28SF040|SST |Flash |SST28SF|All SST28SF0x0 supported|
|
||||
|SST27SF020|SST |Flash |27 |12V continuous for pgm/erase|
|
||||
|W27C257 |Winbond |EEPROM |27 |Continual 12V or 14V for program/erase|
|
||||
|AT29C010 |Atmel |Flash |28C |Only with 128 byte or less sector size|
|
||||
|8755A |Intel |EPROM |8755A |Requires 25V pulses to program|
|
||||
|
||||
|
||||
# Misc Flash
|
||||
|
||||
#### 29C Series
|
||||
|
||||
The 29C series flash chips are similar to the 28C EEPROMs, except they must erase an
|
||||
entire sector before programming new data. The start of a block write operation causes
|
||||
the target sector to be erased before the block is written. If the entire sector is not
|
||||
written in one operation, there is no way to write additional data to the sector because
|
||||
a new block write will erase the sector again.
|
||||
|
||||
The write algorithm for the 29C chips is similar to 28C, so it is possible to use that
|
||||
code to write these chips as well with some restrictions. All 29C010 and 29C020 chips
|
||||
that have been encountered use a sector size of either 64 bytes or 128 bytes. A single
|
||||
XModem packet holds 128 bytes of data, so these chips will program without issue.
|
||||
|
||||
The 28C040 chips from some manufacturers use a 256 byte sector. This will not currently
|
||||
work with TommyPROM, because each of the 128 byte XModem packets received will do its own
|
||||
block write. The first write will erase 256 bytes and then write data into the first half
|
||||
of the sector. The second write will then erase the data just written and then write 128
|
||||
bytes into the second half of the sector. To fix this, the code would need to be modified
|
||||
to keep 256 bytes of data from two packets before initiating a block write.
|
||||
|
||||
#### 28F Series
|
||||
|
||||
The 28F series flash do not have sectors. The entire chip must be erased before writing
|
||||
new data. Data is written a byte at a time using a command register to control the
|
||||
programming. **These chips require a 12V programming voltage that must be present during
|
||||
the programming or erase operations**. TommyPROM does not currently support 28F chips,
|
||||
but it would not be difficult to write a driver. The default 28C driver will read 28F
|
||||
chips.
|
||||
|
||||
#### 29F Series
|
||||
|
||||
The 29F series flash have sectors that must be explicitly erased before writing new
|
||||
data. Data is written a byte at a time using a command register to control the
|
||||
programming. TommyPROM does not currently support 29F chips, but it would not be
|
||||
difficult to write a driver. The default 28C driver will read 29F chips.
|
||||
|
||||
|
||||
#### 28C256
|
||||
|
||||
Tested with chips from several manufacturers including Atmel AT28C256, Xicor X28C256, and
|
||||
CSI CAT28C256. Also works with the smaller 28C64 and 28C16 chips, although some
|
||||
parameters may need to be adjusted. Some smaller chips do not support SDP, so the _Lock_
|
||||
and _Unlock_ commands have no effect. Check the datasheet to see if block writes are
|
||||
supported. Some 28C16s use a 16 byte block instead of the 64 bytes used on the 28C256.
|
||||
It is always safe to just set the block size parameter to zero when declaring the chip to
|
||||
disable block writes altogether.
|
||||
|
||||
The 28C chips do not need to be explicitly erased. Each memory cell is automatically
|
||||
erased during a write operation, so they are more similar to a slow RAM than to other
|
||||
PROMs.
|
||||
|
||||
#### SST39SF040
|
||||
|
||||
The SST39SF driver supports all chips in this family, so the 040, 020, and 010 chips can
|
||||
be all be used with no code change. These chips use sectors that must be erased before
|
||||
writing new data. The code keeps track of the current sector and will automatically do
|
||||
an erase operation whenever a write starts to a new sector. The _Erase_ command is
|
||||
supported, but is not needed unless overwriting new data to a single sector.
|
||||
|
||||
#### SST28SF040
|
||||
|
||||
This is an earlier version of the SST39SF series chips. They are pin compatible with the
|
||||
39SF series, but use a different command set for programming. Unlike the 39SF, these
|
||||
flash chips support software data protection. The _Lock_ and _Unlock_ commands can be
|
||||
used to enable and disable SDP from the command line.
|
||||
|
||||
#### SST27SF020
|
||||
|
||||
The Silicon Storage SST27SF0x0 are programmed similarly to the 27C257 in that a constant
|
||||
voltage is applied for program and erase operations. Unlike the 27C257, these have a
|
||||
dedicated WE pin that controls programming and erasing. Another difference is that they
|
||||
do not have a verify operation to read back the programmed data.
|
||||
|
||||
These Flash chips have a _VPP_ pin that needs a constant 12V during programming. Unlike
|
||||
the newer 28C EEPROMs, these chips do not automatically erase before writing to a
|
||||
location. Instead, the entire chip is erased by applying 12V to _VPP_ and _A9_ and then
|
||||
pulsing _WE_.
|
||||
|
||||
#### W27C257 and W27C512
|
||||
|
||||
The Winbond W27C257 and W27E257 appear to be identical 32Kx8 EEPROMs. The 27C version
|
||||
has been tested. The Winbond W27C512 is a 64Kx8 EEPROM with no dedicated _VPP_ pin.
|
||||
|
||||
The 257 EEPROMs have a _VPP_ pin that needs a constant 12V during programming. Unlike the
|
||||
newer 28C EEPROMs, these chips do not automatically erase before writing to a location.
|
||||
Instead, the entire chip is erased by applying 14V to _VPP_ and _A9_ and then pulsing
|
||||
_CE_.
|
||||
|
||||
Unlike the 257 chips, the W27C512 does not have a dedicated pin for the programming
|
||||
voltage and instead uses the OE pin to place the chip in programming mode. The verify
|
||||
operation requires that the OE pin be switched to _LOW_ and there is no hardware support
|
||||
for this, so the current code supports the 512 chip by doing a single write cycle with no
|
||||
verify.
|
||||
|
||||
Because the chips use a constant high voltage for programming instead of a pulse, an
|
||||
external power supply and two diodes can be used to supply either 5V or 12V to the
|
||||
pins for programming and erasing.
|
||||
|
||||
Note that the W27x257 chip are almost a drop-in replacement for the 28C256. The _WE_,
|
||||
_VPP_, and _A14_ pins are the only differences. For reading, the _VPP_ pin should be
|
||||
connected to 5V.
|
||||
|
||||
#### 29C010
|
||||
|
||||
The 29C0x0 chips are 5V sectored flash chips. They automatically erase a sector at the
|
||||
start of a new write, so they can be used with the default 28C code.
|
||||
|
||||
Note that some versions of the 29C040 use a 256 byte sector size. This will not work
|
||||
with the TommyPROM code because the XModem transfer buffer is only 128 bytes. Code
|
||||
changes would be needed to buffer up two packets of data into a single write operation
|
||||
for chips with the 256 byte buffer.
|
||||
|
||||
# Chips to be Tested
|
||||
|
||||
|Model |Manufacturer |Type |Module |Notes|
|
||||
|:--- |:--- |:--- |:--- |:--- |
|
||||
|M27C4001 |ST Micro |EEPROM | |VCC=6.5V, VPP=12.75V to pgm|
|
||||
|W27C512 |Winbond |EEPROM |27 |Continual 12V or 14V for program/erase,VPP on OE|
|
||||
|
|
@ -68,12 +68,12 @@ add an external power supply and manually assert the voltage before starting a w
|
|||
those with switched voltages, some elements of the 8755 hardware may be leveraged to build
|
||||
a version of the programer that supports these chips.
|
||||
|
||||
## Atmel SST39FS Flash
|
||||
## Atmel SST39SF Flash
|
||||
|
||||
TommyPROM has a driver for Atmel SST39FS NOR flash chips. This driver replaces the 28C
|
||||
TommyPROM has a driver for Atmel SST39SF NOR flash chips. This driver replaces the 28C
|
||||
driver at compile time. See configure.h to enable a different driver.
|
||||
|
||||
The SST39FS chips use fixed 4KB sectors that must be manually erased before a new program
|
||||
The SST39SF chips use fixed 4KB sectors that must be manually erased before a new program
|
||||
operation, but the code manages this transparently. Whenever a write is started to a new
|
||||
segment, the driver first initiates an erase of that sector. A second write to the same
|
||||
sector will not cause an erase, so it is possible to write to a segment multiple times
|
||||
|
|
@ -84,7 +84,7 @@ bytes could be written to the end of the sector from another file.
|
|||
Writing data that spans multiple sectors also works with no additional steps. When
|
||||
a sector boundary is crossed, the new sector is erased and set as the current sector.
|
||||
|
||||
The SST39FS driver supports a manual erase from the command line using the E command.
|
||||
The SST39SF driver supports a manual erase from the command line using the E command.
|
||||
This is only needed if data will be rewritten to the same location after a previous write
|
||||
to that sector.
|
||||
|
||||
|
|
@ -154,17 +154,7 @@ need for shift registers to create address lines.
|
|||
|
||||
The 8755 build of TommyPROM also has a circuit to control the 25V programming pulses.
|
||||
|
||||
# Verified Chips
|
||||
|
||||
|Model |Manufacturer |Type |Module |Notes|
|
||||
|:--- |:--- |:--- |:--- |:--- |
|
||||
|AT28C256 |Atmel, others|EEPROM |28C |Fully supported|
|
||||
|SST39SF040|Microchip |Flash |SST39SF|All SST39SF0x0 supported|
|
||||
|SST28SF040|SST |Flash |SST39SF|All SST28SF0x0 supported|
|
||||
|SST27SF020|SST |Flash |27 |12V continuous for pgm/erase|
|
||||
|W27C257 |Winbond |EEPROM |27 |Continual 12V or 14V for program/erase|
|
||||
|AT29C010 |Atmel |Flash |28C |Only with 128 byte or less sector size|
|
||||
|8755A |Intel |EPROM |8755A |Requires 25V pulses to program|
|
||||
# Chips
|
||||
|
||||
#### 28C256
|
||||
|
||||
|
|
@ -240,10 +230,3 @@ Note that some versions of the 29C040 use a 256 byte sector size. This will not
|
|||
with the TommyPROM code because the XModem transfer buffer is only 128 bytes. Code
|
||||
changes would be needed to buffer up two packets of data into a single write operation
|
||||
for chips with the 256 byte buffer.
|
||||
|
||||
# Chips to be Tested
|
||||
|
||||
|Model |Manufacturer |Type |Module |Notes|
|
||||
|:--- |:--- |:--- |:--- |:--- |
|
||||
|M27C4001 |ST Micro |EEPROM | |VCC=6.5V, VPP=12.75V to pgm|
|
||||
|W27C512 |Winbond |EEPROM |27 |Continual 12V or 14V for program/erase,VPP on OE|
|
||||
|
|
|
|||
Loading…
Reference in New Issue