TommyPROM/HardwareVerify/PromDevice28C.cpp

#include "Configure.h"

#include "PromAddressDriver.h"



PromDevice28C::PromDevice28C(unsigned long size, word blockSize, unsigned maxWriteTime, bool polling)
    : PromDevice(size, blockSize, maxWriteTime, polling)
{
}

void PromDevice28C::begin()
{
    // Define the data bus as input initially so that it does not put out a
    // signal that could collide with output on the data pins of the EEPROM.
    setDataBusMode(INPUT);

    // Define the EEPROM control pins as output, making sure they are all
    // in the disabled state.
    digitalWrite(OE, HIGH);
    pinMode(OE, OUTPUT);
    digitalWrite(CE, HIGH);
    pinMode(CE, OUTPUT);
    digitalWrite(WE, HIGH);
    pinMode(WE, OUTPUT);

    // This chip uses the shift register hardware for addresses, so initialize that.
    PromAddressDriver::begin();
}


// Write the special six-byte code to turn off Software Data Protection.
void PromDevice28C::disableSoftwareWriteProtect()
{
    disableOutput();
    disableWrite();
    setDataBusMode(OUTPUT);

    setByte(0xaa, 0x5555);
    setByte(0x55, 0x2aaa);
    setByte(0x80, 0x5555);
    setByte(0xaa, 0x5555);
    setByte(0x55, 0x2aaa);
    setByte(0x20, 0x5555);

    setDataBusMode(INPUT);
    disableChip();
}


// Write the special three-byte code to turn on Software Data Protection.
void PromDevice28C::enableSoftwareWriteProtect()
{
    disableOutput();
    disableWrite();
    setDataBusMode(OUTPUT);

    setByte(0xaa, 0x5555);
    setByte(0x55, 0x2aaa);
    setByte(0xa0, 0x5555);

    setDataBusMode(INPUT);
    disableChip();
}


// BEGIN PRIVATE METHODS
//

// Use the PromAddressDriver to set a 16 bit address in the two address shift registers.
void PromDevice28C::setAddress(word address)
{
    PromAddressDriver::setAddress(address);
}


// Read a byte from a given address
byte PromDevice28C::readByte(word address)
{
    byte data = 0;
    setAddress(address);
    setDataBusMode(INPUT);
    disableOutput();
    disableWrite();
    enableChip();
    enableOutput();
    data = readDataBus();
    disableOutput();
    disableChip();

    return data;
}


// Burn a byte to the chip and verify that it was written.
bool PromDevice28C::burnByte(byte value, word address)
{
    bool status = false;

    disableOutput();
    disableWrite();

    setAddress(address);
    setDataBusMode(OUTPUT);
    writeDataBus(value);

    enableChip();
    delayMicroseconds(1);
    enableWrite();
    delayMicroseconds(1);
    disableWrite();

    status = waitForWriteCycleEnd(value);

    disableChip();

    return status;
}


bool PromDevice28C::burnBlock(byte data[], word len, word address)
{
    bool status = false;

    if (len == 0)  return true;

    disableOutput();
    disableWrite();
    enableChip();

    // Write all of the bytes in the block out to the chip.  The chip will
    // program them all at once as long as they are written fast enough.
    setDataBusMode(OUTPUT);
    for (word ix = 0; (ix < len); ix++)
    {
        setAddress(address + ix);
        writeDataBus(data[ix]);

        delayMicroseconds(1);
        enableWrite();
        delayMicroseconds(1);
        disableWrite();
    }

    status = waitForWriteCycleEnd(data[len - 1]);
    disableChip();

    return status;
}


bool PromDevice28C::waitForWriteCycleEnd(byte lastValue)
{
    if (mSupportsDataPoll)
    {
        // Verify programming complete by reading the last value back until it matches the
        // value written twice in a row.  The D7 bit will read the inverse of last written
        // data and the D6 bit will toggle on each read while in programming mode.
        //
        // Note that the max readcount is set to the device's maxReadTime (in uSecs)
        // divided by two because there are two 1 uSec delays in the loop.  In reality,
        // the loop could run for longer because this does not account for the time needed
        // to run all of the loop code.  In actual practice, the loop will terminate much
        // earlier because it will detect the end of the write well before the max time.
        setDataBusMode(INPUT);
        delayMicroseconds(1);
        for (int readCount = mMaxWriteTime * 1000 / 2; (readCount > 0); readCount--)
        {
            enableOutput();
            delayMicroseconds(1);
            byte b1 = readDataBus();
            disableOutput();
            enableOutput();
            delayMicroseconds(1);
            byte b2 = readDataBus();
            disableOutput();
            if ((b1 == b2) && (b1 == lastValue))
            {
                return true;
            }
        }

        return false;
    }
    else
    {
        // No way to detect success.  Just wait the max write time.
        delayMicroseconds(mMaxWriteTime * 1000L);
        return true;
    }
}


// Set an address and data value and toggle the write control.  This is used
// to write control sequences, like the software write protect.  This is not a
// complete byte write function because it does not set the chip enable or the
// mode of the data bus.
void PromDevice28C::setByte(byte value, word address)
{
    setAddress(address);
    writeDataBus(value);

    delayMicroseconds(1);
    enableChip();
    enableWrite();
    delayMicroseconds(1);
    disableWrite();
    disableChip();
}