TommyPROM/HardwareVerify/HardwareVerify.ino

265 lines
6.4 KiB
C++

/**
* Test hardware for ATMEL 28C series EEPROMs.
*
* The hardware uses two 74LS164 shift registers as the low and
* high address registers.
**/
#include "Configure.h"
#define LED 13
PromDevice28C prom(32 * 1024L, 64, 10, true);
/*****************************************************************************/
/*****************************************************************************/
/**
* CLI parse functions
*/
const char hex[] = "0123456789abcdef";
// Read a line of data from the serial connection.
char * readLine(char * buffer, int len)
{
for (int ix = 0; (ix < len); ix++)
{
buffer[ix] = 0;
}
// read serial data until linebreak or buffer is full
char c = ' ';
int ix = 0;
do {
if (Serial.available())
{
c = Serial.read();
if ((c == '\b') && (ix > 0))
{
// Backspace, forget last character
--ix;
}
buffer[ix++] = c;
Serial.write(c);
}
} while ((c != '\n') && (ix < len));
buffer[ix - 1] = 0;
return buffer;
}
/************************************************************
* convert a single hex character [0-9a-fA-F] to its value
* @param char c single character (digit)
* @return byte value of the digit (0-15)
************************************************************/
byte hexDigit(char c)
{
if ((c >= '0') && (c <= '9'))
{
return c - '0';
}
else if ((c >= 'a') && (c <= 'f'))
{
return c - 'a' + 10;
}
else if ((c >= 'A') && (c <= 'F'))
{
return c - 'A' + 10;
}
else
{
return 0xff;
}
}
/************************************************************
* convert a hex byte (00 - ff) to byte
* @param c-string with the hex value of the byte
* @return byte represented by the digits
************************************************************/
byte hexByte(char * a)
{
return (hexDigit(a[0]) << 4) | hexDigit(a[1]);
}
/************************************************************
* convert a hex word (0000 - ffff) to unsigned int
* @param c-string with the hex value of the word
* @return unsigned int represented by the digits
************************************************************/
unsigned int hexWord(char * data)
{
return (hexDigit(data[0]) << 12) |
(hexDigit(data[1]) << 8) |
(hexDigit(data[2]) << 4) |
(hexDigit(data[3]));
}
void printByte(byte b)
{
char line[3];
line[0] = hex[b >> 4];
line[1] = hex[b & 0x0f];
line[2] = '\0';
Serial.print(line);
}
void printWord(word w)
{
char line[5];
line[0] = hex[(w >> 12) & 0x0f];
line[1] = hex[(w >> 8) & 0x0f];
line[2] = hex[(w >> 4) & 0x0f];
line[3] = hex[(w) & 0x0f];
line[4] = '\0';
Serial.print(line);
}
/************************************************
* MAIN
*************************************************/
word addr = 0;
void setup()
{
// Do this first so that it initializes all of the hardware pins into a
// non-harmful state. The Arduino or the target EEPROM could be damaged
// if both writing to the data bus at the same time.
prom.begin();
Serial.begin(115200);
}
void loop()
{
commandLoop();
}
static void commandLoop()
{
byte b;
word w;
char line[20];
uint32_t numBytes;
unsigned long timeStart;
unsigned long timeEnd;
bool cmdError = false;
Serial.print("\n#");
Serial.flush();
readLine(line, sizeof(line));
byte c = tolower(line[0]);
if ((c >= 'A') && (c <= 'Z')) {
c |= 0x20;
}
switch (c)
{
case 'a':
if (hexDigit(line[1]) <= 15)
{
w = hexWord(line + 1);
prom.setAddress(w);
}
else
cmdError = true;
break;
case 'd':
if (hexDigit(line[1]) <= 15)
{
prom.disableOutput();
prom.setDataBusMode(OUTPUT);
b = hexByte(line + 1);
prom.writeDataBus(b);
}
else
cmdError = true;
break;
case 'c':
case 'o':
case 'w':
if ((line[1] != 'd') && (line[1] != 'e'))
{
cmdError = true;
}
else
{
bool enable = line[1] == 'e';
if (c == 'c')
if (enable) prom.enableChip(); else prom.disableChip();
else if (c == 'w')
if (enable) prom.enableWrite(); else prom.disableWrite();
else { // c == 'o'
if (enable)
{
// Don't allow the prom and the data bus to output at the same time
prom.setDataBusMode(INPUT);
prom.enableOutput();
}
else prom.disableOutput();
}
}
break;
case 'r':
prom.setDataBusMode(INPUT);
prom.enableOutput();
b = prom.readDataBus();
printByte(b);
Serial.println();
prom.disableOutput();
break;
case 'l':
Serial.println(F("Writing the lock code to enable Software Write Protect mode."));
prom.enableSoftwareWriteProtect();
break;
case 'u':
Serial.println(F("Writing the unlock code to disable Software Write Protect mode."));
timeStart = micros();
prom.disableSoftwareWriteProtect();
timeEnd = micros();
Serial.print("Unlock command time in uSec=");
Serial.println(timeEnd - timeStart);
break;
default:
cmdError = true;
break;
}
if (cmdError) {
Serial.print(F("Hardware Verifier - "));
Serial.println(prom.getName());
Serial.println();
Serial.println(F("Valid commands are:"));
Serial.println(F(" Axxxx - Set address bus to xxxx"));
Serial.println(F(" Dxx - Set Data bus to xx"));
Serial.println(F(" Cs - Set Chip enable to state (e=enable, d=disable)"));
Serial.println(F(" Os - Set Output enable to state (e=enable, d=disable)"));
Serial.println(F(" Ws - Set Write enable to state (e=enable, d=disable)"));
Serial.println(F(" R - Read and print the value on the data bus"));
Serial.println(F(" L - Send Lock sequence to enable device Software Data Protection"));
Serial.println(F(" U - Send Unlock sequence to disable device Software Data Protection"));
}
}