mirror of
https://github.com/ole00/afterburner.git
synced 2024-11-22 06:32:01 +00:00
3ee0147d88
This change stores the digi pot indices in the scale 1-255 (previously 1 -128) so the stored values for calibration are no longer valid after this change is uploaded to Arduino. Please re-run the full calibration on your Afterburner!
405 lines
10 KiB
C
405 lines
10 KiB
C
/*
|
|
* Variable voltage functions for Afterburner GAL project.
|
|
*
|
|
* 2024-02-02 Minor changes in varVppInit()
|
|
*/
|
|
#ifndef __AFTB_VPP_H__
|
|
#define __AFTB_VPP_H__
|
|
|
|
#include <EEPROM.h>
|
|
|
|
// ensure mcp4131 pot uses the right pins
|
|
#define POT_CS A3
|
|
#define POT_CLK A4
|
|
#define POT_DAT A5
|
|
#define VPP A0
|
|
|
|
#include "aftb_mcp4131.h"
|
|
#ifndef FAIL
|
|
#define FAIL 0
|
|
#define OK 1
|
|
#endif
|
|
|
|
#define ABS(X) ((X) < 0 ? -(X) : (X));
|
|
#define VPP_5V0 0xFF
|
|
#define VPP_9V0 0
|
|
#define VPP_9V5 1
|
|
#define VPP_10V0 2
|
|
#define VPP_10V5 3
|
|
#define VPP_11V0 4
|
|
#define VPP_11V5 5
|
|
#define VPP_12V0 6
|
|
#define VPP_12V5 7
|
|
#define VPP_13V0 8
|
|
#define VPP_13V5 9
|
|
#define VPP_14V0 10
|
|
#define VPP_14V5 11
|
|
#define VPP_15V0 12
|
|
#define VPP_15V5 13
|
|
#define VPP_16V0 14
|
|
#define VPP_16V5 15
|
|
|
|
#define MAX_WIPER 16
|
|
|
|
#define VPP_VERBOSE 0
|
|
|
|
#ifdef EXTERNAL
|
|
#define ANALOG_REF_EXTERNAL EXTERNAL
|
|
#else
|
|
#define ANALOG_REF_EXTERNAL AR_EXTERNAL
|
|
#endif
|
|
|
|
//UNO R4 Minima or Wifi (Aref internally pulled down by 130kOhm, AVR Uno R3 pulled down by 32kOhm)
|
|
#ifdef _RENESAS_RA_
|
|
#define AREF_IS_3V2
|
|
#endif
|
|
|
|
//pot wiper indices for the voltages
|
|
uint8_t vppWiper[MAX_WIPER] = {0};
|
|
|
|
// VPP must ramp-up to prevent voltage spikes and possibly resetting arduino
|
|
// These values are for mcp4151 (for mcp4131 they are divided by 2)
|
|
#define varVppSetMax() varVppSetVppIndex(0x80); \
|
|
varVppSetVppIndex(0xE0); \
|
|
varVppSetVppIndex(0xF4); \
|
|
varVppSetVppIndex(0xFA); \
|
|
varVppSetVppIndex(0xFF);
|
|
|
|
|
|
#define varVppSetMin() varVppSetVppIndex(0x0);
|
|
|
|
uint8_t wiperStat = 0; //enabled / disabled
|
|
int8_t calOffset = 0; // VPP calibration offset: value 10 is 0.1V, value -10 is -0.1V
|
|
|
|
static void varVppReadCalib(void) {
|
|
uint8_t i;
|
|
//calibration not found
|
|
if (EEPROM.read(0) != 0xAF || EEPROM.read(1) != 0xCA) {
|
|
vppWiper[0] = 0;
|
|
Serial.println(F("No calibration data in EEPROM"));
|
|
return;
|
|
}
|
|
calOffset = (int8_t) EEPROM.read(2);
|
|
for (i = 0; i < MAX_WIPER; i++) {
|
|
vppWiper[i] = EEPROM.read(i + 3);
|
|
#if 0
|
|
Serial.print(F("Calib "));
|
|
Serial.print(i);
|
|
Serial.print(F(":"));
|
|
Serial.println(vppWiper[i]);
|
|
#endif
|
|
}
|
|
}
|
|
|
|
// internal use only - set the wiper value on the digital pot
|
|
static void varVppSetVppIndex(uint8_t value) {
|
|
uint8_t i;
|
|
|
|
#if VPP_VERBOSE
|
|
Serial.print(F("varSetVppIndex "));
|
|
Serial.println(value);
|
|
#endif
|
|
mcp4131_write(ADDR_WIPER, value);
|
|
#if VPP_PARANOID
|
|
i = mcp4131_read(ADDR_WIPER);
|
|
if (i != value) {
|
|
Serial.print(F("Error writing POT value. Expected:"));
|
|
Serial.print(value);
|
|
Serial.print(F(" Actual:"));
|
|
Serial.println(i);
|
|
}
|
|
#endif
|
|
if (value == 0) {
|
|
mcp4131_disableWiper();
|
|
wiperStat = 0;
|
|
} else if (wiperStat == 0) {
|
|
mcp4131_enableWiper();
|
|
wiperStat = 1;
|
|
}
|
|
}
|
|
|
|
//use by the app code - set the variable voltage
|
|
static void varVppSet(uint8_t value) {
|
|
uint8_t v;
|
|
int8_t inc;
|
|
int8_t incMin;
|
|
if (value == VPP_5V0 || value >= MAX_WIPER) {
|
|
varVppSetVppIndex(0);
|
|
return;
|
|
}
|
|
#if VPP_VERBOSE
|
|
Serial.print(F("varSetVpp "));
|
|
Serial.print(value);
|
|
Serial.print(F(":"));
|
|
Serial.println(vppWiper[value]);
|
|
#endif
|
|
//ramp up to prevent massive voltage overshoots
|
|
v = vppWiper[value] / 2;
|
|
v -= 2;
|
|
inc = 16;
|
|
incMin = 2;
|
|
if (value > VPP_13V0) {
|
|
incMin = 1;
|
|
}
|
|
while (v < vppWiper[value]) {
|
|
varVppSetVppIndex(v);
|
|
v+= inc + (inc / 2);
|
|
inc -= inc / 2;
|
|
if (inc < incMin) {
|
|
inc = incMin;
|
|
}
|
|
}
|
|
varVppSetVppIndex(vppWiper[value]);
|
|
}
|
|
|
|
// UNO R4/Minima - Renesas IC (significant ADC gain errors measured)
|
|
#ifdef AREF_IS_3V2
|
|
#define SAMPLE_CNT 16
|
|
#define SAMPLE_DIVIDER 8
|
|
#define SAMPLE_MULTIPLIER 25
|
|
// SAMPLE_SHIFT moves the ADC gain error up/down
|
|
#define SAMPLE_SHIFT -45;
|
|
|
|
//AVR based Arduinos (no ADC gain errors measured)
|
|
#else
|
|
#define SAMPLE_CNT 14
|
|
#define SAMPLE_DIVIDER 8
|
|
#define SAMPLE_MULTIPLIER 1
|
|
#define SAMPLE_OFFSET 5
|
|
#endif
|
|
|
|
static int16_t varVppMeasureVpp(int8_t printValue) {
|
|
int8_t i = 0;
|
|
uint16_t r1 = 0;
|
|
int16_t r2; //correction for ADC gain error
|
|
|
|
while (i++ < SAMPLE_CNT) {
|
|
r1 += analogRead(VPP);
|
|
}
|
|
r2 = (r1 / (SAMPLE_DIVIDER * SAMPLE_MULTIPLIER));
|
|
#ifdef SAMPLE_OFFSET
|
|
r1+= SAMPLE_OFFSET;
|
|
#endif
|
|
r1 /= SAMPLE_DIVIDER;
|
|
#ifdef SAMPLE_SHIFT
|
|
r2 += SAMPLE_SHIFT;
|
|
r1 += r2;
|
|
#endif
|
|
r1 += calOffset;
|
|
if (printValue) {
|
|
uint8_t a = r1%100;
|
|
Serial.print(r1/100);
|
|
Serial.print(F("."));
|
|
if (a < 10) {
|
|
Serial.print(F("0"));
|
|
}
|
|
#if 1
|
|
Serial.println(a);
|
|
#else
|
|
//debug - display the voltage skew value in r2
|
|
Serial.print(a);
|
|
Serial.println(F(", "));
|
|
Serial.println(r2);
|
|
#endif
|
|
}
|
|
return r1;
|
|
}
|
|
|
|
// Returns 1 on Success, 0 on Failure
|
|
static uint8_t varVppCalibrateVpp(void) {
|
|
uint8_t vppIndex = 0;
|
|
uint8_t i = 1;
|
|
int16_t v = 900; //starting at 9.00 V
|
|
int16_t r1 = 0;
|
|
int16_t r2;
|
|
int16_t minDif;
|
|
|
|
Serial.print(F("VPP calib. offset: "));
|
|
Serial.println(calOffset);
|
|
|
|
varVppSetVppIndex(1);
|
|
delay(300); //settle voltage
|
|
|
|
while (1) {
|
|
// reset the 'minimal difference' variable every time we search for a new index
|
|
minDif = 9000;
|
|
//the 'vppWiper' storage for tap indices is 8bit wide, therefore we must not use tap index 256.
|
|
while (i <= 0xFF) {
|
|
int16_t d1,d2;
|
|
varVppSetVppIndex(i);
|
|
delay(100); //let the voltage settle
|
|
|
|
r2 = varVppMeasureVpp(0);
|
|
// Sanity check: the previous voltage can't be higher than the voltage just measured
|
|
// because we are ramping up the voltage. Therefore it must be an ADC measurement
|
|
// glitch. In that case use the previous value as the measured one.
|
|
// This can happen at lower tap indices where the voltage differences are very small (like 0.01V).
|
|
if (r1 > r2) {
|
|
r2 = r1;
|
|
}
|
|
d1 = r1 - v;
|
|
d2 = r2 - v;
|
|
d1 = ABS(d1);
|
|
d2 = ABS(d2);
|
|
#if VPP_VERBOSE
|
|
Serial.print(i);
|
|
Serial.print(F(") r2="));
|
|
Serial.print(r2, DEC);
|
|
Serial.print(F(" d1="));
|
|
Serial.print(d1, DEC);
|
|
Serial.print(F(" d2="));
|
|
Serial.print(d2, DEC);
|
|
Serial.print(F(" md="));
|
|
Serial.println(minDif, DEC);
|
|
#endif
|
|
|
|
if (r2 <= 100) { // less than 1V ? Failure
|
|
r1 = FAIL;
|
|
goto ret;
|
|
}
|
|
|
|
if (d2 <= minDif) {
|
|
minDif = d2;
|
|
vppWiper[vppIndex] = i;
|
|
//check last value / voltage
|
|
if (i == 0xFF) {
|
|
if (v >= 1620 && v <= 1670) {
|
|
Serial.println(F("*Index for VPP 1650 is 255"));
|
|
r1 = OK;
|
|
goto ret;
|
|
}
|
|
r1 = FAIL;
|
|
goto ret;
|
|
}
|
|
} else {
|
|
i--;
|
|
minDif = 5000;
|
|
Serial.print(F("*Index for VPP "));
|
|
Serial.print(v);
|
|
Serial.print(F(" is "));
|
|
Serial.println(i);
|
|
break;
|
|
}
|
|
|
|
r1 = r2;
|
|
i++;
|
|
}
|
|
vppIndex++;
|
|
#if VPP_VERBOSE
|
|
Serial.print(F("vppIndex "));
|
|
Serial.println(vppIndex);
|
|
#endif
|
|
if (vppIndex >= MAX_WIPER) {
|
|
r1 = OK;
|
|
goto ret;
|
|
}
|
|
v += 50; //next voltage to search for is 0.5V higher
|
|
}
|
|
|
|
ret:
|
|
varVppSet(VPP_5V0);
|
|
return r1;
|
|
|
|
}
|
|
|
|
static void varVppStoreWiperCalib() {
|
|
uint8_t i = 0;
|
|
//sanity check
|
|
if (vppWiper[0] == 0) {
|
|
return;
|
|
}
|
|
|
|
//write Afterburner calibration header
|
|
EEPROM.update(0, 0xAF);
|
|
EEPROM.update(1, 0xCA);
|
|
EEPROM.update(2, (uint8_t) calOffset);
|
|
while (i < MAX_WIPER) {
|
|
EEPROM.update(3 + i, vppWiper[i]);
|
|
i++;
|
|
}
|
|
}
|
|
|
|
|
|
//return 1 on success (variable VPP functionality present), 0 on failure (VPP not detected on board)
|
|
static int8_t varVppInit(void) {
|
|
analogReference(ANALOG_REF_EXTERNAL); //use 3V3 external reference
|
|
analogRead(VPP); // Perform a dummy conversion referring to the datasheet
|
|
|
|
wiperStat = 0; //wiper disabled
|
|
mcp4131_init();
|
|
if (mcp4131_detect()) {
|
|
#if VPP_VERBOSE
|
|
Serial.print(mcp4131_detected ? F("MCP4131") : F("MCP4151"));
|
|
Serial.println(F(" POT found"));
|
|
#endif
|
|
return OK;
|
|
} else {
|
|
#if VPP_VERBOSE
|
|
Serial.println(F("POT not found"));
|
|
#endif
|
|
return FAIL;
|
|
}
|
|
}
|
|
|
|
//return 1 on success (VPP calibration appears correct), 0 on failure
|
|
static int8_t varVppCheckCalibration(void) {
|
|
int16_t v;
|
|
|
|
varVppReadCalib();
|
|
if (vppWiper[0] == 0) {
|
|
Serial.println(F("I: VPP not calibrated"));
|
|
return FAIL;
|
|
}
|
|
|
|
#if 0
|
|
// This shoots the VPP to 9V - in theory no GALs should have an issue with that voltage.
|
|
// Also, the On switch should be turned off, preventing VPP to reach the GAL pins.
|
|
// check actual voltage
|
|
varVppSet(VPP_9V0);
|
|
delay(200); //Settle voltage
|
|
v = varVppMeasureVpp(0);
|
|
varVppSet(VPP_5V0); //set VPP back to 5V
|
|
// lower voltages have a good resolution, so we can have a tight voltage check bounds
|
|
if (v < 890 || v > 910) {
|
|
Serial.print(F("ER: VPP voltage check of 9V failed. Expected 900, measured "));
|
|
Serial.println(v);
|
|
return FAIL;
|
|
}
|
|
#endif
|
|
return OK;
|
|
}
|
|
|
|
// only for VPP testing and debugging
|
|
static void varrVppTestRamp(void) {
|
|
uint8_t i = 1;
|
|
|
|
while (i < 256) {
|
|
varVppSetVppIndex(i);
|
|
delay(400);
|
|
Serial.println(i, DEC);
|
|
varVppMeasureVpp(1);
|
|
i++;
|
|
}
|
|
delay(2000);
|
|
varVppSetVppIndex(0);
|
|
|
|
|
|
}
|
|
|
|
static int8_t varVppCalibrate(void) {
|
|
#if 0
|
|
// only for testing and debugging
|
|
varrVppTestRamp();
|
|
return OK;
|
|
#endif
|
|
|
|
if (varVppCalibrateVpp()) {
|
|
varVppStoreWiperCalib();
|
|
} else {
|
|
Serial.println(F("ER: Wiper calibration failed"));
|
|
return FAIL;
|
|
}
|
|
return OK;
|
|
}
|
|
#endif
|