afterburner/aftb_mcp4131.h
ole00 4db4108d4a Sketch: added support for new board design (v 3.0)
New features:
* unified socket for 20 pin and 24 devices (including GAL20V8)
* variable VPP via digi pot
* VPP measurement via A0 ADC (used for VPP calibration)
2023-04-07 19:15:36 +01:00

118 lines
2.8 KiB
C

//MCP4131 digital pot - bitbanged control
//set default pins
#ifndef POT_CS
#define POT_CS A3
#endif
#ifndef POT_CLK
#define POT_CLK A4
#endif
#ifndef POT_DAT
#define POT_DAT A5
#endif
#ifndef POT_DEFAULT_VALUE
#define POT_DEFAULT_VALUE 0x40
#endif
#ifndef POT_WIPER_ENABLED
#define POT_WIPER_ENABLED 0
#endif
#define ADDR_WIPER 0
#define ADDR_WIPER0 0
#define ADDR_WIPER1 1
#define ADDR_TCON 4
#define ADDR_STAT 5
#define CMD_READ (0b11 << 10)
#define mcp4131_disableWiper() mcp4131_write(ADDR_TCON, 0b111111101)
#define mcp4131_enableWiper() mcp4131_write(ADDR_TCON, 0b111111111)
#define mcp4131_read(A) mcp4131_reg((A),0,1)
#define mcp4131_write(A,V) mcp4131_reg((A),(V),0)
// read or write the mcp4131 register
static uint16_t mcp4131_reg(uint8_t address, uint16_t value, uint8_t read_reg) {
int8_t i;
uint16_t r = address;
r <<= 12;
if (read_reg) {
r |= CMD_READ;
} else {
r |= value & 0x1FF; // clamp value to 9 bits
}
//setup Clock and and Data (SPI mode 0,0)
digitalWrite(POT_CLK, 0);
digitalWrite(POT_DAT, 0);
delayMicroseconds(50);
//activate IC
digitalWrite(POT_CS, 0);
i = 15;
while (i >= 0) {
//write address and command (bits 15 to 10)
if ((!read_reg) || i > 9) {
uint16_t mask = (1 << i);
digitalWrite(POT_DAT, (r & mask) ? 1 : 0);
}
digitalWrite(POT_CLK, 1); //rise the clock
//only when reading reg
if (read_reg) {
//switch the DAT pin to Input
if (i == 10) {
pinMode(POT_DAT, INPUT);
}
//read bits 9 to 0
if (i < 10) {
r |= (digitalRead(POT_DAT) << i); //read after rising edge
}
}
digitalWrite(POT_CLK, 0); //fall the clock
i--;
}
if (read_reg) {
pinMode(POT_DAT, OUTPUT);
}
//disable IC
digitalWrite(POT_CS, 1);
return r & 0x1FF; //clamp value to 9 bits
}
static void mcp4131_init(void) {
pinMode(POT_CS, OUTPUT);
pinMode(POT_CLK, OUTPUT);
pinMode(POT_DAT, OUTPUT);
digitalWrite(POT_CS, 1); //unselect the POT's SPI bus
}
// initialisation and detection
// returns 1 if POT is detected, 0 otherwise
static uint8_t mcp4131_detect(void) {
uint16_t r;
mcp4131_disableWiper();
//note checking is done while the wiper is disabled - no resistance is applied
mcp4131_write(ADDR_WIPER, 0b1010);
r = mcp4131_read(ADDR_WIPER);
if (r != 0b1010) {
return 0;
}
mcp4131_write(ADDR_WIPER, 0b101);
r = mcp4131_read(ADDR_WIPER);
if (r != 0b101) {
return 0;
}
mcp4131_write(ADDR_WIPER, POT_DEFAULT_VALUE);
#if POT_WIPER_ENABLED
mcp4131_enableWiper();
#endif
return 1;
}