mirror of
https://github.com/JorjBauer/aiie.git
synced 2024-11-26 11:49:19 +00:00
271 lines
8.3 KiB
C++
271 lines
8.3 KiB
C++
#include "ay8910.h"
|
|
#include <stdio.h>
|
|
|
|
#include "globals.h"
|
|
|
|
// Map our linear 4-bit amplitude to 8-bit output level
|
|
static const uint8_t volumeLevels[16] = { 0x00, 0x04, 0x05, 0x07,
|
|
0x0B, 0x10, 0x16, 0x23,
|
|
0x2B, 0x44, 0x5A, 0x73,
|
|
0x92, 0xB0, 0xD9, 0xFF };
|
|
|
|
// Envelope constants
|
|
enum {
|
|
AY_ENV_HOLD = 1,
|
|
AY_ENV_ALT = 2,
|
|
AY_ENV_ATTACK = 4,
|
|
AY_ENV_CONT = 8
|
|
};
|
|
|
|
/* Envelope handling
|
|
* (Per General Instruments AY-3-8910 documentation.)
|
|
*
|
|
* Envelope period is set in the 16-bit value r[0x0C]:r[0x0B] (where 0 = 1).
|
|
* The resulting frequency is from 0.12Hz to 7812.5 Hz.
|
|
*
|
|
* The shape of the envelope is selected by r[0x0D] and uses the
|
|
* constants above.
|
|
*
|
|
* If AY_ENV_HOLD is set, then when the envelope reaches terminal (0
|
|
* or 15) it stays there.
|
|
*
|
|
* If AY_ENV_ALT is set, the direction reverses each time it reaches
|
|
* terminal. (If both AY_ENV_HOLD and AY_ENV_ALT are set, then the
|
|
* envelope counter returns to its initial count before holding.)
|
|
*
|
|
* If AY_ENV_ATTACK is set, the counter is ascending (0-to-15); otherwise
|
|
* it is descending (15-to-0).
|
|
*
|
|
* If AY_ENV_CONT is *clear* (0), then the counter resets to 0 after
|
|
* one cycle and holds there. If it is 1, it does whatever HOLD
|
|
* says. (So AY_ENV_CONT==0 takes priority over AY_ENV_HOLD).
|
|
*
|
|
*
|
|
*/
|
|
|
|
AY8910::AY8910()
|
|
{
|
|
Reset();
|
|
}
|
|
|
|
void AY8910::Reset()
|
|
{
|
|
curRegister = 0;
|
|
|
|
// FIXME: what are the right default values?
|
|
for (uint8_t i=0; i<16; i++)
|
|
r[i] = 0x00;
|
|
waveformFlipTimer[0] = waveformFlipTimer[1] = waveformFlipTimer[2] = 0;
|
|
outputState[0] = outputState[1] = outputState[2] = 0;
|
|
envCounter = 0;
|
|
envelopeTimer = envelopeTime = 0;
|
|
envDirection = 1;
|
|
}
|
|
|
|
uint8_t AY8910::read(uint8_t reg)
|
|
{
|
|
// FIXME: does anything ever need to read from this?
|
|
return 0xFF;
|
|
}
|
|
|
|
// reg represents BC1, BDIR, /RST in bits 0, 1, 2.
|
|
// val is the state of those three bits.
|
|
// PortA is the state of whatever's currently on PortA when we do it.
|
|
void AY8910::write(uint8_t reg, uint8_t PortA)
|
|
{
|
|
// Bit 2 (1 << 2 == 0x04) is wired to the Reset pin. If it goes low,
|
|
// we reset the virtual chip.
|
|
if ((reg & NRSET) == 0) {
|
|
Reset();
|
|
return;
|
|
}
|
|
|
|
// Bit 0 (1 << 0 == 0x01) is the BC1 pin. BC2 is hard-wired to +5v.
|
|
// We can ignore bit 3, b/c that was just checked above & triggered
|
|
// a reset.
|
|
reg &= ~0x04;
|
|
|
|
switch (reg) {
|
|
case IAB: // bDir==0 && BC1 == 0 (IAB)
|
|
// Puts the DA bus in high-impedance state. Nothing for us to do?
|
|
return;
|
|
case DTB: // bDir==0 && BC1 == 1 (DTB)
|
|
// Contents of the currently addressed register are put in DA. FIXME?
|
|
return;
|
|
case DWS: // bDir==1 && BC1 == 0 (DWS)
|
|
// Write current PortA to PSG
|
|
r[curRegister] = PortA;
|
|
if (curRegister <= CHAN_A_COARSE) {
|
|
cycleTime[0] = cycleTimeForPSG(0);
|
|
waveformFlipTimer[0] = g_cpu->cycles + cycleTime[0];
|
|
} else if (curRegister <= CHAN_B_COARSE) {
|
|
cycleTime[1] = cycleTimeForPSG(1);
|
|
waveformFlipTimer[1] = g_cpu->cycles + cycleTime[1];
|
|
} else if (curRegister <= CHAN_C_COARSE) {
|
|
cycleTime[2] = cycleTimeForPSG(2);
|
|
waveformFlipTimer[2] = g_cpu->cycles + cycleTime[2];
|
|
} else if (curRegister == ENAB) {
|
|
if (r[ENAB] & ENAB_N_TONEA) {
|
|
cycleTime[0] = waveformFlipTimer[0] = 0;
|
|
} else {
|
|
cycleTime[0] = cycleTimeForPSG(0);
|
|
waveformFlipTimer[0] = g_cpu->cycles + cycleTime[0];
|
|
}
|
|
if (r[ENAB] & ENAB_N_TONEB) {
|
|
cycleTime[1] = waveformFlipTimer[1] = 0;
|
|
} else {
|
|
cycleTime[1] = cycleTimeForPSG(1);
|
|
waveformFlipTimer[1] = g_cpu->cycles + cycleTime[1];
|
|
}
|
|
if (r[ENAB] & ENAB_N_TONEC) {
|
|
cycleTime[2] = waveformFlipTimer[2] = 0;
|
|
} else {
|
|
cycleTime[2] = cycleTimeForPSG(2);
|
|
waveformFlipTimer[2] = g_cpu->cycles + cycleTime[2];
|
|
}
|
|
} else if (curRegister >= ENV_PERIOD_FINE && curRegister <= ENV_SHAPE) {
|
|
// Envelope control -- period or shape
|
|
// FIXME: should envCounter be initialized to the start position?
|
|
envDirection = (r[ENV_SHAPE] & AY_ENV_ATTACK) ? 1 : -1;
|
|
envelopeTime = calculateEnvelopeTime();
|
|
envelopeTimer = 0; // reset so it will pick up @ next tick
|
|
}
|
|
return;
|
|
case INTAK: // bDir==1 && BC1 == 1 (INTAK)
|
|
// Select current register
|
|
curRegister = PortA & 0xF;
|
|
return;
|
|
}
|
|
}
|
|
|
|
// The lowest frequency the AY8910 makes is 30.6 Hz, which is ~33431
|
|
// clock cycles.
|
|
//
|
|
// The highest frequency produced is 125kHz, which is ~8 cycles.
|
|
//
|
|
// The highest practicable, given our 24-cycle-main-loop, is
|
|
// 41kHz. Which should be plenty fine.
|
|
//
|
|
// Conversely: we should be able to call update() as slowly as once
|
|
// every 60-ish clock cycles before we start noticing it in the output
|
|
// audio.
|
|
uint16_t AY8910::cycleTimeForPSG(uint8_t psg)
|
|
{
|
|
// Convert the current registers in to a cycle count for how long
|
|
// between flips of 0-to-1 from the square wave generator.
|
|
|
|
uint16_t regVal = (r[1+(psg*2)] << 8) | (r[0 + (psg*2)]);
|
|
if (regVal == 0) regVal++;
|
|
|
|
// Ft = 4MHz / (32 * regVal); our clock is 1MHz
|
|
// so we should return (32 * regVal) / 4 ?
|
|
|
|
return (32 * regVal) / 4;
|
|
}
|
|
|
|
// Similar calculation: this one, for the envelope timer.
|
|
// FIXME: I *think* this is right. Not sure. Needs validation.
|
|
uint32_t AY8910::calculateEnvelopeTime()
|
|
{
|
|
uint16_t regVal = (r[0x0C] << 8) | (r[0x0B]);
|
|
if (regVal == 0) regVal++;
|
|
|
|
return (512 * regVal) / 4;
|
|
}
|
|
|
|
void AY8910::update(uint32_t cpuCycleCount)
|
|
{
|
|
#if 0
|
|
// Debugging: print state of the 16 registers
|
|
printf("AY8910: ");
|
|
for (int i=0; i<16; i++) {
|
|
printf("%02X ", r[i]);
|
|
}
|
|
printf("%04X %04X %04X\n", cycleTime[0], cycleTime[1], cycleTime[2]);
|
|
#endif
|
|
|
|
// update the envelope timer if it's time
|
|
if (envelopeTime != 0) {
|
|
if (!envelopeTimer) {
|
|
// timer wasn't set, so start it running
|
|
envelopeTimer = cpuCycleCount + envelopeTime;
|
|
}
|
|
if (envelopeTimer <= cpuCycleCount) {
|
|
// time to update the envelopeCounter.
|
|
|
|
switch (r[ENV_SHAPE]) {
|
|
// Continue / Attack / Alternate / Hold bits
|
|
case 0x00: // 0 / 0 / x / x -- descend once, stay @ bottom
|
|
case 0x01: // 0 / 0 / x / x
|
|
case 0x02: // 0 / 0 / x / x
|
|
case 0x03: // 0 / 0 / x / x
|
|
case 0x04: // 0 / 1 / x / x -- ascend once, jump to bottom
|
|
case 0x05: // 0 / 1 / x / x
|
|
case 0x06: // 0 / 1 / x / x
|
|
case 0x07: // 0 / 1 / x / x
|
|
case 0x09: // 1 / 0 / 0 / 1 -- descend once, stay @ bottom
|
|
case 0x0b: // 1 / 0 / 1 / 1 -- descend once, jump to top
|
|
case 0x0d: // 1 / 1 / 0 / 1 -- ascend once, stay @ top
|
|
case 0x0f: // 1 / 1 / 1 / 1 -- ascend once, jump to bottom
|
|
|
|
// In all these cases, we go from start to finish once. In all
|
|
// cases except 0x0b and 0x0d, when we're done, we go low.
|
|
|
|
envCounter += envDirection;
|
|
if (envDirection > 0) {
|
|
// We were ascending: did we hit 16? If so, stop & go terminal
|
|
if (envCounter == 16) {
|
|
envDirection = 0;
|
|
// One ascending case (0x0b) goes high after; all others are low
|
|
envCounter = (r[ENV_SHAPE] == 0x0b ? 0x0F : 0x00);
|
|
}
|
|
} else if (envDirection < 0) {
|
|
// We were descending: did we hit 0? If so, stop & go terminal
|
|
if (envCounter == 0) {
|
|
envDirection = 0;
|
|
// One descending case (0x0d) goes high after; all others are low
|
|
envCounter = (r[ENV_SHAPE] == 0x0d ? 0x0F : 0x00);
|
|
}
|
|
}
|
|
}
|
|
|
|
// Set up the envelope timer for the next transition
|
|
// FIXME: can set this to 0 if envDirection is 0, but have to be careful about setup of timer again when envDirection is re-set
|
|
envelopeTimer += envelopeTime;
|
|
}
|
|
}
|
|
|
|
// For any waveformFlipTimer that is > 0: if cpuCycleCount is larger
|
|
// than the timer, we'll flip state. (It's a square wave!)
|
|
|
|
for (uint8_t i=0; i<3; i++) {
|
|
uint32_t cc = cycleTime[i];
|
|
|
|
if (cc) {
|
|
if (waveformFlipTimer[i] <= cpuCycleCount) {
|
|
// flip when it's time to flip
|
|
waveformFlipTimer[i] += cc;
|
|
outputState[i] = !outputState[i];
|
|
}
|
|
} else {
|
|
outputState[i] = 0;
|
|
}
|
|
|
|
// Figure out what output comes from this channel and send it to
|
|
// the speaker. The output is controlled by outputState[i] (from
|
|
// the square wave, above); the amplitude control line for this
|
|
// output (r[i+8], below) and the tone/noise selection (FIXME:
|
|
// currently unimplemented).
|
|
|
|
uint8_t amplitude = r[i+8] & 0xF;
|
|
// ... and if bit 0x10 is on, it's controlled by the envelope counter.
|
|
if (r[i+8] & 0x10)
|
|
amplitude = envCounter;
|
|
|
|
g_speaker->mixOutput(outputState[i] ? volumeLevels[amplitude] : 0x00);
|
|
|
|
}
|
|
|
|
}
|
|
|