mirror of
https://github.com/V2RetroComputing/analog-firmware.git
synced 2024-06-10 22:29:39 +00:00
Timing tweaks
This commit is contained in:
parent
4586bb8638
commit
3ee0061fdc
|
@ -21,19 +21,19 @@
|
||||||
; x - select Data, active low
|
; x - select Data, active low
|
||||||
.wrap_target
|
.wrap_target
|
||||||
next_bus_cycle:
|
next_bus_cycle:
|
||||||
set PINS, 0b011 ; enable AddrHi tranceiver
|
set PINS, 0b111 ; disable tranceivers
|
||||||
wait 1 GPIO, PHI0_GPIO ; wait for PHI0 to rise. Data propagation through the transceiver should
|
wait 1 GPIO, PHI0_GPIO [5] ; wait for PHI0 to rise.
|
||||||
; be complete by the time this happens.
|
set PINS, 0b011 [5] ; enable AddrHi tranceiver and delay for transceiver propagation delay (24ns)
|
||||||
in PINS, 8 ; read AddrHi[7:0]
|
in PINS, 8 ; read AddrHi[7:0]
|
||||||
set PINS, 0b101 [12] ; enable AddrLo tranceiver and delay for transceiver propagation delay
|
set PINS, 0b101 [5] ; enable AddrLo tranceiver and delay for transceiver propagation delay (24ns)
|
||||||
in PINS, 8 ; read AddrLo[7:0]
|
in PINS, 8 ; read AddrLo[7:0]
|
||||||
|
|
||||||
jmp PIN, read_cycle ; jump based on the state of the R/W pin
|
jmp PIN, read_cycle ; jump based on the state of the R/W pin
|
||||||
|
|
||||||
write_cycle:
|
write_cycle:
|
||||||
; the current time is P0+82ns (P0 + 10ns + 2 clocks (input synchronizers) + 16 instructions)
|
; the current time is P0+88ns (P0 + 10ns + 2 clocks (input synchronizers) + 20 instructions)
|
||||||
|
|
||||||
set PINS, 0b110 [31] ; enable Data tranceiver & wait until both ~DEVSEL and the written data are valid (P0+210ns)
|
set PINS, 0b110 [19] ; enable Data tranceiver & wait until both ~DEVSEL and the written data are valid (P0+170ns)
|
||||||
in PINS, 10 ; read R/W, ~DEVSEL, and Data[7:0], then autopush
|
in PINS, 10 ; read R/W, ~DEVSEL, and Data[7:0], then autopush
|
||||||
wait 0 GPIO, PHI0_GPIO [7] ; wait for PHI0 to fall
|
wait 0 GPIO, PHI0_GPIO [7] ; wait for PHI0 to fall
|
||||||
jmp next_bus_cycle
|
jmp next_bus_cycle
|
||||||
|
@ -41,7 +41,7 @@ write_cycle:
|
||||||
read_cycle:
|
read_cycle:
|
||||||
; the current time is P0+82ns (P0 + 10ns + 2 clocks (input synchronizers) + 16 instructions)
|
; the current time is P0+82ns (P0 + 10ns + 2 clocks (input synchronizers) + 16 instructions)
|
||||||
|
|
||||||
set PINS, 0b110 [4] ; ensure AddrLo transceiver is disabled and delay for ~DEVSEL to become valid (P0+102ns+buffer delay)
|
set PINS, 0b110 [5] ; ensure AddrLo transceiver is disabled and delay for ~DEVSEL to become valid (P0+102ns+buffer delay)
|
||||||
in PINS, 10 ; read R/W, ~DEVSEL, and dontcare[7:0], then autopush
|
in PINS, 10 ; read R/W, ~DEVSEL, and dontcare[7:0], then autopush
|
||||||
|
|
||||||
irq set READ_DATA_TRIGGER_IRQ ; trigger the data read state machine to put data on the data bus
|
irq set READ_DATA_TRIGGER_IRQ ; trigger the data read state machine to put data on the data bus
|
||||||
|
@ -66,26 +66,26 @@ wait_loop:
|
||||||
wait 1 irq READ_DATA_TRIGGER_IRQ ; wait for the data portion of a read cycle (from the main SM)
|
wait 1 irq READ_DATA_TRIGGER_IRQ ; wait for the data portion of a read cycle (from the main SM)
|
||||||
jmp PIN, wait_loop ; skip if this device is not being addressed
|
jmp PIN, wait_loop ; skip if this device is not being addressed
|
||||||
|
|
||||||
; the current time is P0+114ns (P0 + 10ns + 2 clocks (input synchronizers) + 24 instructions) and
|
; the current time is P0+130ns and
|
||||||
; this read cycle is addressed to this device.
|
; this read cycle is addressed to this device.
|
||||||
;
|
;
|
||||||
; Phase 0 is typically 489 ns long.
|
; Phase 0 is typically 489 ns long.
|
||||||
; * Data from peripherals should be valid on the data bus by 45 nanoseconds before the end of phase 0
|
; * Data from peripherals should be valid on the data bus by 45 nanoseconds before the end of phase 0
|
||||||
; * Data should be held for 40ns after phase 0 ends
|
; * Data should be held for no more than 20ns after phase 0 ends
|
||||||
; * Data bus should be tri-stated within 60ns after phase 0 ends
|
; * Data bus should be tri-stated within 30ns after phase 0 ends
|
||||||
|
|
||||||
irq set DATA_BUSY_IRQ
|
irq set DATA_BUSY_IRQ
|
||||||
|
|
||||||
set PINS, 0b01 [10] ; enable Data tranceiver with output direction [160ns]
|
set PINS, 0b01 [7] ; enable Data tranceiver with output direction [P0+162ns]
|
||||||
mov OSR, ~NULL [31] ; [288ns]
|
mov OSR, ~NULL [31] ; [P0+290ns]
|
||||||
out PINDIRS, 8 [31] ; set data pins as outputs [416ns]
|
out PINDIRS, 8 [31] ; set data pins as outputs [P0+418ns]
|
||||||
|
|
||||||
pull noblock ; pull value from the FIFO as late as possible [420ns]
|
pull noblock ; pull value from the FIFO as late as possible [P0+422ns]
|
||||||
out PINS, 8 ; [424ns]
|
out PINS, 8 ; [P0+426ns]
|
||||||
|
|
||||||
; the current time is P0+424ns (P0 + 10ns + 2 clocks (input synchronizers) + 101 instructions)
|
; the current time is P0+426ns
|
||||||
|
|
||||||
wait 0 GPIO, PHI0_GPIO [7] ; wait for PHI0 to fall then hold for 40ns (2 clocks (input synchronizers) + 7 instructions)
|
wait 0 GPIO, PHI0_GPIO [2] ; wait for PHI0 to fall then hold for 12ns (2 clocks (input synchronizers) + 7 instructions)
|
||||||
set PINS, 0b10 ; disable Data tranceiver to tri-state the data bus
|
set PINS, 0b10 ; disable Data tranceiver to tri-state the data bus
|
||||||
|
|
||||||
mov OSR, NULL
|
mov OSR, NULL
|
||||||
|
|
Loading…
Reference in New Issue
Block a user