analog/v2-analog-rev1/common/abus.pio

.define public PHI0_GPIO 26
.define READ_DATA_TRIGGER_IRQ 4
.define DATA_BUSY_IRQ 5

; Apple II bus interface
; Ref: Understanding the Apple II, pages 4-7, 7-8

.program abus
; Prerequisites:
;  * Bus clock used is PHI0, wired to GPIO 26
;  * JMP pin is mapped to the R/W signal
;  * IN pins are mapped to ~DEVSEL, R/W, and Data[7:0]
;  * SET pins are mapped to the transceiver enable signals
;  * input shift left & autopush @ 26 bits
;  * run at about 125MHz (8ns/instruction)
;
; SET bits for tranceiver control:
;  0bxxx
;    x    - select AddrHi, active low
;     x   - select AddrLo, active low
;      x  - select Data, active low
.wrap_target
next_bus_cycle:
    set PINS, 0b011                     ; enable AddrHi tranceiver
    wait 1 GPIO, PHI0_GPIO              ; wait for PHI0 to rise. Data propagation through the transceiver should
                                        ; be complete by the time this happens.
    in PINS, 8                          ; read AddrHi[7:0]
    set PINS, 0b101  [2]                ; enable AddrLo tranceiver and delay for transceiver propagation delay
    in PINS, 8                          ; read AddrLo[7:0]

    jmp PIN, read_cycle                 ; jump based on the state of the R/W pin

write_cycle:
    ; the current time is P0+88ns (P0 + 16ns + 2 clocks (input synchronizers) + 7 instructions)

    set PINS, 0b110  [15]               ; enable Data tranceiver & wait until both ~DEVSEL and the written data are valid (P0+200ns)
    in PINS, 10                         ; read R/W, ~DEVSEL, and Data[7:0], then autopush
    wait 0 GPIO, PHI0_GPIO  [7]         ; wait for PHI0 to fall
    jmp next_bus_cycle

read_cycle:
    ; the current time is P0+88ns (P0 + 16ns + 2 clocks (input synchronizers) + 7 instructions)

    set PINS, 0b110                     ; ensure AddrLo transceiver is disabled and delay for ~DEVSEL to become valid (P0+63ns+buffer delay)
    in PINS, 10                         ; read R/W, ~DEVSEL, and dontcare[7:0], then autopush

    irq set READ_DATA_TRIGGER_IRQ       ; trigger the data read state machine to put data on the data bus
    wait 0 GPIO, PHI0_GPIO   [7]        ; wait for PHI0 to fall
    wait 0 irq DATA_BUSY_IRQ            ; wait for the data handling state machine to complete to avoid contention w/transceiver control
.wrap


.program abus_device_read
; Prerequisites:
;  * Bus clock used is PHI0, wired to GPIO 26
;  * JMP pin is the ~DEVSEL signal
;  * OUT pins are the 8 data signals
;  * SET pins are the Data transceiver control signals
;
; SET bits for tranceiver control:
;  0bxx
;    x  - select Data transceiver (active low)
;     x - Data transceiver direction (0=input, 1=output)
.wrap_target
wait_loop:
    wait 1 irq READ_DATA_TRIGGER_IRQ    ; wait for the data portion of a read cycle (from the main SM)
    jmp PIN, wait_loop                  ; skip if this device is not being addressed

    ; the current time is P0+136ns (P0 + 16ns + 2 clocks (input synchronizers) + 13 instructions) and
    ; this read cycle is addressed to this device.
    ;
    ; Phase 0 is typically 489 ns long.
    ;  * Data from peripherals should be valid on the data bus by 45 nanoseconds before the end of phase 0
    ;  * Data should be held for 40ns after phase 0 ends
    ;  * Data bus should be tri-stated within 60ns after phase 0 ends

    irq set DATA_BUSY_IRQ

    pull noblock                        ; extra early pull to clear out any standing values from the FIFO

    set PINS, 0b01                      ; enable Data tranceiver with output direction
    mov OSR, ~NULL  [3]
    out PINDIRS, 8  [31]                ; set data pins as outputs

    pull noblock                        ; pull value from the FIFO as late as possible
    out PINS, 8

    ; the current time is P0+440ns (P0 + 16ns + 2 clocks (input synchronizers) + 51 instructions)

    wait 0 GPIO, PHI0_GPIO  [2]         ; wait for PHI0 to fall then hold for 40ns  (2 clocks (input synchronizers) + 2-3 instructions)
    set PINS, 0b10                      ; disable Data tranceiver to tri-state the data bus

    mov OSR, NULL
    out PINDIRS, 8                      ; reset data pins as inputs

    irq clear DATA_BUSY_IRQ
.wrap