typo fix

Move cd card slot back slightly.

.gitignore

@@ -1 +1,5 @@
 .DS_Store
+kicad/bluescsi_iigs_internal-backups/*
+**/fp-info-cache
+**/#auto_saved_files#
+**/_autosave*

CHANGES.md

@@ -0,0 +1,30 @@
+# 1.4
+
+## Replace 12v aux power with 5v
+
+This change is for two reasons:
+
+1) The 7805 regulator is wasteful, especially when the IIgs only has 2.5a on the 12v rail
+2) Some models of Apple IIe don't have a fan connector, and most II/II+'s don't
+
+The fix for this will be to get 5v directly from the Game IO (Paddle) Port, a direct tap on the 5V power supply wire, or from a card slot.
+
+This 5v will be used directly via an IC that performs reverse current and over-current protection.
+
+## Branding Changes
+
+The current design has been retroactively branded "BlueGS / BP" to distinguish it from the upcoming RP2040-based "BlueGS / RP"
+
+# 1.3.2
+
+Move External LED connector closer to edge to clear cable plugged in to J1.
+
+Change footprint of D3/D4 to "Diode_SMD:D_SOD-123".
+
+Increase width of 12V and 5V traces.
+
+Move SD Card 3.3v trace to bottom.
+
+Slightly move screw terminal offset to avoid clipped silkscreen warning.
+
+# Older changes not recorded

POWERING_BLUE-GS.md

@@ -0,0 +1,76 @@
+# Powering BlueGS
+
+There are 4 ways to power your BlueGS board, listed here from "most easy" to "least easy".
+
+## Termination Power from SCSI card
+
+If your SCSI card provides [Termination Power](#what-is-termination-power), then you only have to BlueGS to your SCSI card using the included flat 26-pin cable or DB-25-M connector. No additional steps are required, and BlueGS should turn on the moment that the computer is powered up.
+
+## Termination Power from another SCSI device
+
+If your SCSI card does not provide Termination Power, then you can provide the necessary power through another SCSI device connected to the DB-25 connector.
+
+Most external SCSI devices will provide the necessary Termination Power. To power BlueGS this way:
+* Connect the new SCSI device to the DB-25 connector
+* On BlueGS, switch "Termination" to "off"
+* Ensure that the new SCSI device is terminated, either via a switch (if it has one, such as on the IOmega Zip Drive) or an external terminator that connects to one of the SCSI ports of the device.
+
+This external device must be powered-on *before* the IIgs turns on.
+
+## +5V from inside the computer
+
+You can power BlueGS via the "Aux 5V Power In" connector, using a 5V source in your computer. This can be from the Game IO port, a card slot, or a tap from the power supply rail.
+
+If you power BlueGS using this connector, it will also send termination power to any other devices on the SCSI bus that may need it -- such as another BlueSCSI device!
+
+Older versions of BlueGS could be powered by the 12V fan connector in the IIgs, but that has been removed in 1.4 and higher.
+
+## USB port on Blue Pill board
+
+You can power BlueGS using the USB connector on the Blue Pill module as long as you are not also using SCSI Termination Power or 5V aux power.
+
+### Why can't I use USB while BlueGS is powered from SCSI or Aux?
+
+There is a design flaw on the Blue Pill board where power sent to the +5V pin of the board can then be sent *back* through the USB connector. This "backflow" can potentially cause damage to whatever is providing USB power and so it strongly recommended that you do not use USB to power BlueGS while connected to SCSI Termination Power or aux power.
+
+If there is no termination power on your bus and BlueGS is not using the aux power connector, then there is no danger of "backflow" and USB power can be used.
+
+
+# What is Termination Power?
+
+Very briefly, "Termination Power" is electrical current that is used to power devices called "Terminators". A "Terminator" is a device connected to the end of a "bus" (the cable/wire) to show where the end is.
+
+If you think of the SCSI bus as a water pipe and each drive on the bus as a water tap connected to the pipe, then a Terminator is the cap at the end of the pipe.
+
+# What SCSI cards do/don't provide Termination Power?
+
+While many SCSI cards do not provide termination power, there are some that can be modified to that they will.
+
+## Cards that DO provide Termination Power
+
+* [GGLabs A2SCSI](https://gglabs.us/node/2071)
+* RAMFast SCSI - controlled by JP1 or DIP #1, see manual for details
+
+## Cards that DON'T provide Termination Power
+
+* Apple Rev B SCSI
+  - Can be modified to provide termination power
+* Apple Rev C SCSI
+  - Can be modified to provide termination power
+* Apple High-Speed SCSI ("Sandwich II")
+  - Can be modified to provide termination power
+
+## Unknown cards
+
+* AMR SCSI
+* CMS SCSI II
+* Cirtech SCSI/InSyder
+* GSE-Reactive SCSI Card
+* SVA Hard Disk Adapter
+
+# How can I tell if my SCSI card is providing Termination Power?
+
+If your card is not in one of the lists above, then the easiest way is to connect BlueGS and see if it turns on when the the computer is powered on.
+
+If you have a multi-meter, you can check the voltage on pin 25 of the DB-25 connector. If termination power is provided, this pin should read between 4.5 and 5 volts.
+

README.md

@@ -0,0 +1,127 @@
+# BlueGS: Internal BlueSCSI for Apple IIgs and //e
+
+*BlueGS* is the internal hard drive your Apple IIgs and //e always *craved*.
+
+Using the [BlueSCSI](https://github.com/erichelgeson/BlueSCSI) SCSI drive emulator and your compatible SCSI card, you have a fully internal hard drive with accessible microSD slot while still keeping your DB-25 connector free for other peripherals.
+
+[![Close-up of BlueGS installed in IIgs slot](images/bluegs_v1.2_rear_installed_cropped_thumb.jpg)](images/bluegs_v1.2_rear_installed_cropped.jpg)
+[![BlueGS installed in IIgs slot, right side](images/bluegs_v1.2_rear_installed_right_thumb.jpg)](images/bluegs_v1.2_rear_installed_right.jpg)
+[![BlueGS installed in IIgs slot, left side](images/bluegs_v1.2_rear_installed_left_thumb.jpg)](images/bluegs_v1.2_rear_installed_left.jpg)
+
+# How it works
+
+BlueGS connects between your SCSI card and its external DB-25 connector to give you a seamless installation. The BlueGS module itself mounts in a free DB-25 connector cutout in the rear of your IIgs or //e.
+
+[![Overhead view of BlueGS in IIgs slot](images/bluegs_v1.2_installed_overhead_thumb.jpg)](images/bluegs_v1.2_installed_overhead.jpg)
+[![Frontal view of BlueGS in IIgs slot](images/bluegs_v1.2_installed_front_thumb.jpg)](images/bluegs_v1.2_installed_front.jpg)
+
+# Features
+
+* Gives your Apple IIgs or //e an internal, cable-free hard drive
+* Can be powered from SCSI termination power only (if present)
+* "Termination Power" mod is not required (when powered from auxiliary 5V source)
+* Can *provide* termination power to the SCSI bus (when powered from a 5V source such as the Game IO connector or card slot)
+* Built-in termination that is controlled with a single switch
+* Active termination ICs instead of passive termination resistors, reduces power consumption by over 2/3rds
+* Reverse current and voltage protection with overcurrent prevention for auxiliary 5V input
+* Connection for external drive activity LED
+
+[![Annotated picture of front of BlueGS v1.2](images/bluegs-bp-v1.4_board_front_annotated_thumb.jpg)](images/bluegs-bp-v1.4_board_front_annotated.jpg)
+[![Annotated picture of rear of BlueGS v1.2](images/bluegs-bp-v1.4_board_rear_annotated_thumb.jpg)](images/bluegs-bp-v1.4_board_rear_annotated.jpg)
+
+# Compatible SCSI cards
+
+Tested:
+* [GGLabs A2SCSI](https://gglabs.us/node/2071) - a clone of the Apple Rev C SCSI card
+* Apple Rev C SCSI and clones
+* Apple High-Speed SCSI ("Sandwich II")
+* Ramfast SCSI
+
+Assumed to work:
+* GSE-Reactive SCSI Card
+
+Untested:
+* AMR SCSI
+* Cirtech SCSI/Insyder
+* SVA Hard Disk Adapter
+
+The CMS SCSI II is currently confirmed **NOT** to work, though it appears to be a (card) firmware issue and not a "bug" with BlueSCSI.
+
+## What if my SCSI card doesn't provide termination power?
+
+Running BlueGS from "termination power" makes installation much easier, but not all SCSI cards have it. For more details, please check out the notes on [Powering BlueGS](POWERING_BLUE-GS.md).
+
+# Performance
+
+Using [BenchmarkD](https://www.brutaldeluxe.fr/products/apple2gs/benchmarked.html) with Apple IIgs (ROM 1, "Fast" speed), GS-RAM Plus w/ 2MB, GGLabs A2SCSI card. Using Blue-Pill-based BlueGS board.
+
+* Read
+  * File: 52 KB/s
+  * Block-by-block: 36 KB/s
+  * With 64K buffer: 79 KB/s
+* Write (File): 37 KB/s
+
+# Can I use it on things besides the IIgs and //e?
+
+Yes! It's a standard BlueSCSI device and uses the standard BlueSCSI V1 firmware. In fact, the built-in DB-25 connector makes it the perfect external SCSI drive as well!
+
+BlueGS can be mounted internally in any computer that has an open cutout for a DB-25 connector.
+
+## ✅ Compatible Apple clones
+
+These computers *do* have rear DB-25 cutouts and so BlueGS should be able to mount properly, but are untested.
+
+* Franklin Ace 2000/2100/2200
+* Basis 108
+
+## 🚫 Apple II/II+ and similar clones
+
+BlueGS will function in an Apple II or II+, but you will not be able to mount it because it uses "V" shaped cutouts instead of D-Subminiature connector cutouts like the //e and IIgs have.
+
+Many Apple II clones use the same rear cutout design and have the same mounting limitation. **A mounting solution for these machine is planned**.
+
+* Franklin Ace 100/1000/1200
+* Pravetz-8
+  - Includes the -8, -82, -8M, -8A, -8E, and -8C
+* Unitron (Brazil)
+* Ci Base-48 and Pineapple (Korea)
+
+
+# Assembly
+
+If you purchased BlueGS as a self-assemble kit or are using your own PCBs, please follow the instructions in the "[assembly](assembly/)" directory.
+
+If your BlueGS was purchased fully-assembled, please move on to the "[Installation](installation/)" section.
+# Installation
+
+Installation guides can be found in the "[installation](installation/)" directory.
+# Schematics
+
+[V1.4 Schematic](schematics/schematic_v1.4.pdf) (**FINAL**, recommended design)
+
+<details>
+  <summary>Older Schematics</summary>
+
+[V1.3 Schematic](schematics/schematic_v1.3.pdf)
+
+[V1.2 Schematic](schematics/schematic_v1.2.pdf)
+
+[V1.1 Schematic](schematics/schematic_v1.1.pdf)
+
+</details>
+
+# EDA/Kicad and Gerber Files
+
+Kicad of current design can be found in [kicad](kicad/) directory.
+
+# Credits
+
+This project would not be possible without the work done by [ztto](https://github.com/ztto/ArdSCSino-stm32), [Tambo](https://twitter.com/h_koma2), [Eric Helgeson](https://github.com/erichelgeson/BlueSCSI), [Androda](https://androda.work/), and many others.
+
+The "Blue Pill" footprint was originally created by [Yet-Another-Average-Joe](https://github.com/yet-another-average-joe/Kicad-STM32).
+
+Symbol and footprint for Molex 105162-0001 MicroSD slot created by [SnapEDA user HMantz](https://www.snapeda.com/parts/105162-0001/Molex/view-part/).
+
+# License
+
+See [LICENSE.md](LICENSE.md).

TERMINATION.md

@@ -0,0 +1,27 @@
+# Blue-GS: Compatible Termination ICs
+
+## Blue-GS v1.2 and above
+
+Any of the following in a SOIC-16 package are compatible:
+* UC5603
+* UC5604
+* UC5605
+* UCC5612
+* UCC5606
+
+### JP1 & JP2 Setting
+
+Please note that JP1 and JP2 must be set differently depending on the ICs used.
+
+* UC5605, UCC5606
+  - JP1: bridge 1 and 2
+  - JP2: bridge 2 and 3
+* UC5603, UC5604, UCC5612
+  - JP1: bridge 2 and 3
+  - JP2: bridge 1 and 2
+
+## Blue-GS v1.1
+
+Either of the following in SOIC-16 package are compatible:
+* UC5605
+* UCC5606

assembly/README.md

@@ -0,0 +1,11 @@
+# BlueGS Assembly Guide
+
+<!-- TOC -->
+
+- [BlueGS Assembly Guide](#bluegs-assembly-guide)
+- [V1.3 Assembly Guide](#v13-assembly-guide)
+
+<!-- /TOC -->
+# V1.3 Assembly Guide
+
+The assembly guide for V1.3 of BlueGS is forthcoming, pending test results of the V1.2 design.

gerber/v1.2/bluescsi_iigs_internal-B_Mask.gbr

@@ -0,0 +1,500 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(5.1.8-0-10_14)*%
+%TF.CreationDate,2021-05-17T09:41:11-06:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Soldermask,Bot*%
+%TF.FilePolarity,Negative*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (5.1.8-0-10_14)) date 2021-05-17 09:41:11*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+%ADD10C,2.100000*%
+%ADD11O,1.700000X1.700000*%
+%ADD12R,1.700000X1.700000*%
+%ADD13R,0.800000X0.900000*%
+%ADD14C,0.900000*%
+%ADD15C,1.700000*%
+%ADD16R,1.970000X0.600000*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,M2*%
+X172461000Y-48791000D03*
+X177541000Y-48791000D03*
+X172461000Y-53871000D03*
+X177541000Y-53871000D03*
+%TD*%
+%TO.C,M1*%
+X172461000Y-95481000D03*
+X177541000Y-95481000D03*
+X172461000Y-100561000D03*
+X177541000Y-100561000D03*
+%TD*%
+D11*
+%TO.C,J5*%
+X132080000Y-92075000D03*
+D12*
+X132080000Y-89535000D03*
+%TD*%
+%TO.C,R3*%
+G36*
+G01*
+X172066000Y-87814999D02*
+X172066000Y-88715001D01*
+G75*
+G02*
+X171816001Y-88965000I-249999J0D01*
+G01*
+X171115999Y-88965000D01*
+G75*
+G02*
+X170866000Y-88715001I0J249999D01*
+G01*
+X170866000Y-87814999D01*
+G75*
+G02*
+X171115999Y-87565000I249999J0D01*
+G01*
+X171816001Y-87565000D01*
+G75*
+G02*
+X172066000Y-87814999I0J-249999D01*
+G01*
+G37*
+G36*
+G01*
+X174066000Y-87814999D02*
+X174066000Y-88715001D01*
+G75*
+G02*
+X173816001Y-88965000I-249999J0D01*
+G01*
+X173115999Y-88965000D01*
+G75*
+G02*
+X172866000Y-88715001I0J249999D01*
+G01*
+X172866000Y-87814999D01*
+G75*
+G02*
+X173115999Y-87565000I249999J0D01*
+G01*
+X173816001Y-87565000D01*
+G75*
+G02*
+X174066000Y-87814999I0J-249999D01*
+G01*
+G37*
+%TD*%
+D13*
+%TO.C,Q1*%
+X172085000Y-85201000D03*
+X173035000Y-83201000D03*
+X171135000Y-83201000D03*
+%TD*%
+%TO.C,F1*%
+G36*
+G01*
+X148395000Y-91300000D02*
+X146245000Y-91300000D01*
+G75*
+G02*
+X145995000Y-91050000I0J250000D01*
+G01*
+X145995000Y-90300000D01*
+G75*
+G02*
+X146245000Y-90050000I250000J0D01*
+G01*
+X148395000Y-90050000D01*
+G75*
+G02*
+X148645000Y-90300000I0J-250000D01*
+G01*
+X148645000Y-91050000D01*
+G75*
+G02*
+X148395000Y-91300000I-250000J0D01*
+G01*
+G37*
+G36*
+G01*
+X148395000Y-94100000D02*
+X146245000Y-94100000D01*
+G75*
+G02*
+X145995000Y-93850000I0J250000D01*
+G01*
+X145995000Y-93100000D01*
+G75*
+G02*
+X146245000Y-92850000I250000J0D01*
+G01*
+X148395000Y-92850000D01*
+G75*
+G02*
+X148645000Y-93100000I0J-250000D01*
+G01*
+X148645000Y-93850000D01*
+G75*
+G02*
+X148395000Y-94100000I-250000J0D01*
+G01*
+G37*
+%TD*%
+D11*
+%TO.C,J4*%
+X131445000Y-99060000D03*
+D12*
+X131445000Y-96520000D03*
+%TD*%
+%TO.C,C4*%
+G36*
+G01*
+X137019000Y-96937000D02*
+X137019000Y-95087000D01*
+G75*
+G02*
+X137269000Y-94837000I250000J0D01*
+G01*
+X138269000Y-94837000D01*
+G75*
+G02*
+X138519000Y-95087000I0J-250000D01*
+G01*
+X138519000Y-96937000D01*
+G75*
+G02*
+X138269000Y-97187000I-250000J0D01*
+G01*
+X137269000Y-97187000D01*
+G75*
+G02*
+X137019000Y-96937000I0J250000D01*
+G01*
+G37*
+G36*
+G01*
+X133769000Y-96937000D02*
+X133769000Y-95087000D01*
+G75*
+G02*
+X134019000Y-94837000I250000J0D01*
+G01*
+X135019000Y-94837000D01*
+G75*
+G02*
+X135269000Y-95087000I0J-250000D01*
+G01*
+X135269000Y-96937000D01*
+G75*
+G02*
+X135019000Y-97187000I-250000J0D01*
+G01*
+X134019000Y-97187000D01*
+G75*
+G02*
+X133769000Y-96937000I0J250000D01*
+G01*
+G37*
+%TD*%
+D14*
+%TO.C,SW1*%
+X184226000Y-63095000D03*
+X184226000Y-60095000D03*
+%TD*%
+%TO.C,C3*%
+G36*
+G01*
+X156555000Y-96252000D02*
+X158405000Y-96252000D01*
+G75*
+G02*
+X158655000Y-96502000I0J-250000D01*
+G01*
+X158655000Y-97502000D01*
+G75*
+G02*
+X158405000Y-97752000I-250000J0D01*
+G01*
+X156555000Y-97752000D01*
+G75*
+G02*
+X156305000Y-97502000I0J250000D01*
+G01*
+X156305000Y-96502000D01*
+G75*
+G02*
+X156555000Y-96252000I250000J0D01*
+G01*
+G37*
+G36*
+G01*
+X156555000Y-93002000D02*
+X158405000Y-93002000D01*
+G75*
+G02*
+X158655000Y-93252000I0J-250000D01*
+G01*
+X158655000Y-94252000D01*
+G75*
+G02*
+X158405000Y-94502000I-250000J0D01*
+G01*
+X156555000Y-94502000D01*
+G75*
+G02*
+X156305000Y-94252000I0J250000D01*
+G01*
+X156305000Y-93252000D01*
+G75*
+G02*
+X156555000Y-93002000I250000J0D01*
+G01*
+G37*
+%TD*%
+%TO.C,C2*%
+G36*
+G01*
+X161889000Y-96252000D02*
+X163739000Y-96252000D01*
+G75*
+G02*
+X163989000Y-96502000I0J-250000D01*
+G01*
+X163989000Y-97502000D01*
+G75*
+G02*
+X163739000Y-97752000I-250000J0D01*
+G01*
+X161889000Y-97752000D01*
+G75*
+G02*
+X161639000Y-97502000I0J250000D01*
+G01*
+X161639000Y-96502000D01*
+G75*
+G02*
+X161889000Y-96252000I250000J0D01*
+G01*
+G37*
+G36*
+G01*
+X161889000Y-93002000D02*
+X163739000Y-93002000D01*
+G75*
+G02*
+X163989000Y-93252000I0J-250000D01*
+G01*
+X163989000Y-94252000D01*
+G75*
+G02*
+X163739000Y-94502000I-250000J0D01*
+G01*
+X161889000Y-94502000D01*
+G75*
+G02*
+X161639000Y-94252000I0J250000D01*
+G01*
+X161639000Y-93252000D01*
+G75*
+G02*
+X161889000Y-93002000I250000J0D01*
+G01*
+G37*
+%TD*%
+%TO.C,C1*%
+G36*
+G01*
+X163435000Y-53757000D02*
+X163435000Y-51907000D01*
+G75*
+G02*
+X163685000Y-51657000I250000J0D01*
+G01*
+X164685000Y-51657000D01*
+G75*
+G02*
+X164935000Y-51907000I0J-250000D01*
+G01*
+X164935000Y-53757000D01*
+G75*
+G02*
+X164685000Y-54007000I-250000J0D01*
+G01*
+X163685000Y-54007000D01*
+G75*
+G02*
+X163435000Y-53757000I0J250000D01*
+G01*
+G37*
+G36*
+G01*
+X160185000Y-53757000D02*
+X160185000Y-51907000D01*
+G75*
+G02*
+X160435000Y-51657000I250000J0D01*
+G01*
+X161435000Y-51657000D01*
+G75*
+G02*
+X161685000Y-51907000I0J-250000D01*
+G01*
+X161685000Y-53757000D01*
+G75*
+G02*
+X161435000Y-54007000I-250000J0D01*
+G01*
+X160435000Y-54007000D01*
+G75*
+G02*
+X160185000Y-53757000I0J250000D01*
+G01*
+G37*
+%TD*%
+D11*
+%TO.C,J2*%
+X144780000Y-85090000D03*
+X142240000Y-85090000D03*
+X144780000Y-82550000D03*
+X142240000Y-82550000D03*
+X144780000Y-80010000D03*
+X142240000Y-80010000D03*
+X144780000Y-77470000D03*
+X142240000Y-77470000D03*
+X144780000Y-74930000D03*
+X142240000Y-74930000D03*
+X144780000Y-72390000D03*
+X142240000Y-72390000D03*
+X144780000Y-69850000D03*
+X142240000Y-69850000D03*
+X144780000Y-67310000D03*
+X142240000Y-67310000D03*
+X144780000Y-64770000D03*
+X142240000Y-64770000D03*
+X144780000Y-62230000D03*
+X142240000Y-62230000D03*
+X144780000Y-59690000D03*
+X142240000Y-59690000D03*
+X144780000Y-57150000D03*
+X142240000Y-57150000D03*
+X144780000Y-54610000D03*
+D12*
+X142240000Y-54610000D03*
+%TD*%
+D15*
+%TO.C,U1*%
+X167640000Y-50800000D03*
+D12*
+X152400000Y-50800000D03*
+D15*
+X167640000Y-53340000D03*
+X152400000Y-53340000D03*
+X167640000Y-55880000D03*
+X152400000Y-55880000D03*
+X167640000Y-58420000D03*
+X152400000Y-58420000D03*
+X167640000Y-60960000D03*
+X152400000Y-60960000D03*
+X167640000Y-63500000D03*
+X152400000Y-63500000D03*
+X167640000Y-66040000D03*
+X152400000Y-66040000D03*
+X167640000Y-68580000D03*
+X152400000Y-68580000D03*
+X167640000Y-71120000D03*
+X152400000Y-71120000D03*
+X167640000Y-73660000D03*
+X152400000Y-73660000D03*
+X167640000Y-76200000D03*
+X152400000Y-76200000D03*
+X167640000Y-78740000D03*
+X152400000Y-78740000D03*
+X167640000Y-81280000D03*
+X152400000Y-81280000D03*
+X167640000Y-83820000D03*
+X152400000Y-83820000D03*
+X167640000Y-86360000D03*
+X152400000Y-86360000D03*
+X167640000Y-88900000D03*
+X152400000Y-88900000D03*
+X167640000Y-91440000D03*
+X152400000Y-91440000D03*
+X167640000Y-93980000D03*
+X152400000Y-93980000D03*
+X167640000Y-96520000D03*
+X152400000Y-96520000D03*
+X167640000Y-99060000D03*
+X152400000Y-99060000D03*
+%TD*%
+D16*
+%TO.C,U3*%
+X162495000Y-81915000D03*
+X162495000Y-83185000D03*
+X162495000Y-84455000D03*
+X162495000Y-85725000D03*
+X162495000Y-86995000D03*
+X162495000Y-88265000D03*
+X162495000Y-89535000D03*
+X162495000Y-90805000D03*
+X157545000Y-90805000D03*
+X157545000Y-89535000D03*
+X157545000Y-88265000D03*
+X157545000Y-86995000D03*
+X157545000Y-85725000D03*
+X157545000Y-84455000D03*
+X157545000Y-83185000D03*
+X157545000Y-81915000D03*
+%TD*%
+%TO.C,U2*%
+X162495000Y-56515000D03*
+X162495000Y-57785000D03*
+X162495000Y-59055000D03*
+X162495000Y-60325000D03*
+X162495000Y-61595000D03*
+X162495000Y-62865000D03*
+X162495000Y-64135000D03*
+X162495000Y-65405000D03*
+X157545000Y-65405000D03*
+X157545000Y-64135000D03*
+X157545000Y-62865000D03*
+X157545000Y-61595000D03*
+X157545000Y-60325000D03*
+X157545000Y-59055000D03*
+X157545000Y-57785000D03*
+X157545000Y-56515000D03*
+%TD*%
+D11*
+%TO.C,J1*%
+X134620000Y-85090000D03*
+X132080000Y-85090000D03*
+X134620000Y-82550000D03*
+X132080000Y-82550000D03*
+X134620000Y-80010000D03*
+X132080000Y-80010000D03*
+X134620000Y-77470000D03*
+X132080000Y-77470000D03*
+X134620000Y-74930000D03*
+X132080000Y-74930000D03*
+X134620000Y-72390000D03*
+X132080000Y-72390000D03*
+X134620000Y-69850000D03*
+X132080000Y-69850000D03*
+X134620000Y-67310000D03*
+X132080000Y-67310000D03*
+X134620000Y-64770000D03*
+X132080000Y-64770000D03*
+X134620000Y-62230000D03*
+X132080000Y-62230000D03*
+X134620000Y-59690000D03*
+X132080000Y-59690000D03*
+X134620000Y-57150000D03*
+X132080000Y-57150000D03*
+X134620000Y-54610000D03*
+D12*
+X132080000Y-54610000D03*
+%TD*%
+M02*

gerber/v1.2/bluescsi_iigs_internal-B_Paste.gbr

@@ -0,0 +1,360 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(5.1.8-0-10_14)*%
+%TF.CreationDate,2021-05-17T09:41:11-06:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Paste,Bot*%
+%TF.FilePolarity,Positive*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (5.1.8-0-10_14)) date 2021-05-17 09:41:11*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+%ADD10R,0.800000X0.900000*%
+%ADD11R,1.970000X0.600000*%
+G04 APERTURE END LIST*
+%TO.C,R3*%
+G36*
+G01*
+X172066000Y-87814999D02*
+X172066000Y-88715001D01*
+G75*
+G02*
+X171816001Y-88965000I-249999J0D01*
+G01*
+X171115999Y-88965000D01*
+G75*
+G02*
+X170866000Y-88715001I0J249999D01*
+G01*
+X170866000Y-87814999D01*
+G75*
+G02*
+X171115999Y-87565000I249999J0D01*
+G01*
+X171816001Y-87565000D01*
+G75*
+G02*
+X172066000Y-87814999I0J-249999D01*
+G01*
+G37*
+G36*
+G01*
+X174066000Y-87814999D02*
+X174066000Y-88715001D01*
+G75*
+G02*
+X173816001Y-88965000I-249999J0D01*
+G01*
+X173115999Y-88965000D01*
+G75*
+G02*
+X172866000Y-88715001I0J249999D01*
+G01*
+X172866000Y-87814999D01*
+G75*
+G02*
+X173115999Y-87565000I249999J0D01*
+G01*
+X173816001Y-87565000D01*
+G75*
+G02*
+X174066000Y-87814999I0J-249999D01*
+G01*
+G37*
+%TD*%
+D10*
+%TO.C,Q1*%
+X172085000Y-85201000D03*
+X173035000Y-83201000D03*
+X171135000Y-83201000D03*
+%TD*%
+%TO.C,F1*%
+G36*
+G01*
+X148395000Y-91300000D02*
+X146245000Y-91300000D01*
+G75*
+G02*
+X145995000Y-91050000I0J250000D01*
+G01*
+X145995000Y-90300000D01*
+G75*
+G02*
+X146245000Y-90050000I250000J0D01*
+G01*
+X148395000Y-90050000D01*
+G75*
+G02*
+X148645000Y-90300000I0J-250000D01*
+G01*
+X148645000Y-91050000D01*
+G75*
+G02*
+X148395000Y-91300000I-250000J0D01*
+G01*
+G37*
+G36*
+G01*
+X148395000Y-94100000D02*
+X146245000Y-94100000D01*
+G75*
+G02*
+X145995000Y-93850000I0J250000D01*
+G01*
+X145995000Y-93100000D01*
+G75*
+G02*
+X146245000Y-92850000I250000J0D01*
+G01*
+X148395000Y-92850000D01*
+G75*
+G02*
+X148645000Y-93100000I0J-250000D01*
+G01*
+X148645000Y-93850000D01*
+G75*
+G02*
+X148395000Y-94100000I-250000J0D01*
+G01*
+G37*
+%TD*%
+%TO.C,C4*%
+G36*
+G01*
+X137019000Y-96937000D02*
+X137019000Y-95087000D01*
+G75*
+G02*
+X137269000Y-94837000I250000J0D01*
+G01*
+X138269000Y-94837000D01*
+G75*
+G02*
+X138519000Y-95087000I0J-250000D01*
+G01*
+X138519000Y-96937000D01*
+G75*
+G02*
+X138269000Y-97187000I-250000J0D01*
+G01*
+X137269000Y-97187000D01*
+G75*
+G02*
+X137019000Y-96937000I0J250000D01*
+G01*
+G37*
+G36*
+G01*
+X133769000Y-96937000D02*
+X133769000Y-95087000D01*
+G75*
+G02*
+X134019000Y-94837000I250000J0D01*
+G01*
+X135019000Y-94837000D01*
+G75*
+G02*
+X135269000Y-95087000I0J-250000D01*
+G01*
+X135269000Y-96937000D01*
+G75*
+G02*
+X135019000Y-97187000I-250000J0D01*
+G01*
+X134019000Y-97187000D01*
+G75*
+G02*
+X133769000Y-96937000I0J250000D01*
+G01*
+G37*
+%TD*%
+%TO.C,C3*%
+G36*
+G01*
+X156555000Y-96252000D02*
+X158405000Y-96252000D01*
+G75*
+G02*
+X158655000Y-96502000I0J-250000D01*
+G01*
+X158655000Y-97502000D01*
+G75*
+G02*
+X158405000Y-97752000I-250000J0D01*
+G01*
+X156555000Y-97752000D01*
+G75*
+G02*
+X156305000Y-97502000I0J250000D01*
+G01*
+X156305000Y-96502000D01*
+G75*
+G02*
+X156555000Y-96252000I250000J0D01*
+G01*
+G37*
+G36*
+G01*
+X156555000Y-93002000D02*
+X158405000Y-93002000D01*
+G75*
+G02*
+X158655000Y-93252000I0J-250000D01*
+G01*
+X158655000Y-94252000D01*
+G75*
+G02*
+X158405000Y-94502000I-250000J0D01*
+G01*
+X156555000Y-94502000D01*
+G75*
+G02*
+X156305000Y-94252000I0J250000D01*
+G01*
+X156305000Y-93252000D01*
+G75*
+G02*
+X156555000Y-93002000I250000J0D01*
+G01*
+G37*
+%TD*%
+%TO.C,C2*%
+G36*
+G01*
+X161889000Y-96252000D02*
+X163739000Y-96252000D01*
+G75*
+G02*
+X163989000Y-96502000I0J-250000D01*
+G01*
+X163989000Y-97502000D01*
+G75*
+G02*
+X163739000Y-97752000I-250000J0D01*
+G01*
+X161889000Y-97752000D01*
+G75*
+G02*
+X161639000Y-97502000I0J250000D01*
+G01*
+X161639000Y-96502000D01*
+G75*
+G02*
+X161889000Y-96252000I250000J0D01*
+G01*
+G37*
+G36*
+G01*
+X161889000Y-93002000D02*
+X163739000Y-93002000D01*
+G75*
+G02*
+X163989000Y-93252000I0J-250000D01*
+G01*
+X163989000Y-94252000D01*
+G75*
+G02*
+X163739000Y-94502000I-250000J0D01*
+G01*
+X161889000Y-94502000D01*
+G75*
+G02*
+X161639000Y-94252000I0J250000D01*
+G01*
+X161639000Y-93252000D01*
+G75*
+G02*
+X161889000Y-93002000I250000J0D01*
+G01*
+G37*
+%TD*%
+%TO.C,C1*%
+G36*
+G01*
+X163435000Y-53757000D02*
+X163435000Y-51907000D01*
+G75*
+G02*
+X163685000Y-51657000I250000J0D01*
+G01*
+X164685000Y-51657000D01*
+G75*
+G02*
+X164935000Y-51907000I0J-250000D01*
+G01*
+X164935000Y-53757000D01*
+G75*
+G02*
+X164685000Y-54007000I-250000J0D01*
+G01*
+X163685000Y-54007000D01*
+G75*
+G02*
+X163435000Y-53757000I0J250000D01*
+G01*
+G37*
+G36*
+G01*
+X160185000Y-53757000D02*
+X160185000Y-51907000D01*
+G75*
+G02*
+X160435000Y-51657000I250000J0D01*
+G01*
+X161435000Y-51657000D01*
+G75*
+G02*
+X161685000Y-51907000I0J-250000D01*
+G01*
+X161685000Y-53757000D01*
+G75*
+G02*
+X161435000Y-54007000I-250000J0D01*
+G01*
+X160435000Y-54007000D01*
+G75*
+G02*
+X160185000Y-53757000I0J250000D01*
+G01*
+G37*
+%TD*%
+D11*
+%TO.C,U3*%
+X162495000Y-81915000D03*
+X162495000Y-83185000D03*
+X162495000Y-84455000D03*
+X162495000Y-85725000D03*
+X162495000Y-86995000D03*
+X162495000Y-88265000D03*
+X162495000Y-89535000D03*
+X162495000Y-90805000D03*
+X157545000Y-90805000D03*
+X157545000Y-89535000D03*
+X157545000Y-88265000D03*
+X157545000Y-86995000D03*
+X157545000Y-85725000D03*
+X157545000Y-84455000D03*
+X157545000Y-83185000D03*
+X157545000Y-81915000D03*
+%TD*%
+%TO.C,U2*%
+X162495000Y-56515000D03*
+X162495000Y-57785000D03*
+X162495000Y-59055000D03*
+X162495000Y-60325000D03*
+X162495000Y-61595000D03*
+X162495000Y-62865000D03*
+X162495000Y-64135000D03*
+X162495000Y-65405000D03*
+X157545000Y-65405000D03*
+X157545000Y-64135000D03*
+X157545000Y-62865000D03*
+X157545000Y-61595000D03*
+X157545000Y-60325000D03*
+X157545000Y-59055000D03*
+X157545000Y-57785000D03*
+X157545000Y-56515000D03*
+%TD*%
+M02*

gerber/v1.2/bluescsi_iigs_internal-Eco1_User.gbr

@@ -0,0 +1,14 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(5.1.8-0-10_14)*%
+%TF.CreationDate,2021-05-17T09:41:11-06:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Other,ECO1*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (5.1.8-0-10_14)) date 2021-05-17 09:41:11*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 APERTURE END LIST*
+M02*

gerber/v1.2/bluescsi_iigs_internal-Eco2_User.gbr

@@ -0,0 +1,14 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(5.1.8-0-10_14)*%
+%TF.CreationDate,2021-05-17T09:41:11-06:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Other,ECO2*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (5.1.8-0-10_14)) date 2021-05-17 09:41:11*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 APERTURE END LIST*
+M02*

gerber/v1.2/bluescsi_iigs_internal-Edge_Cuts.gbr

@@ -0,0 +1,74 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(5.1.8-0-10_14)*%
+%TF.CreationDate,2021-05-17T09:41:11-06:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Profile,NP*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (5.1.8-0-10_14)) date 2021-05-17 09:41:11*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+%TA.AperFunction,Profile*%
+%ADD10C,0.050000*%
+%TD*%
+G04 APERTURE END LIST*
+D10*
+X180721000Y-94996000D02*
+G75*
+G02*
+X181991000Y-93726000I1270000J0D01*
+G01*
+X181991000Y-56134000D02*
+G75*
+G02*
+X180721000Y-54864000I0J1270000D01*
+G01*
+X185293000Y-56134000D02*
+G75*
+G02*
+X186563000Y-57404000I0J-1270000D01*
+G01*
+X186563000Y-92456000D02*
+G75*
+G02*
+X185293000Y-93726000I-1270000J0D01*
+G01*
+X130175000Y-102362000D02*
+G75*
+G02*
+X128905000Y-101092000I0J1270000D01*
+G01*
+X180721000Y-101092000D02*
+G75*
+G02*
+X179451000Y-102362000I-1270000J0D01*
+G01*
+X179451000Y-46990000D02*
+G75*
+G02*
+X180721000Y-48260000I0J-1270000D01*
+G01*
+X128905000Y-48260000D02*
+G75*
+G02*
+X130175000Y-46990000I1270000J0D01*
+G01*
+X181991000Y-93726000D02*
+X185293000Y-93726000D01*
+X180721000Y-94996000D02*
+X180721000Y-101092000D01*
+X181991000Y-56134000D02*
+X185293000Y-56134000D01*
+X180721000Y-48260000D02*
+X180721000Y-54864000D01*
+X130175000Y-46990000D02*
+X179451000Y-46990000D01*
+X128905000Y-101092000D02*
+X128905000Y-48260000D01*
+X179451000Y-102362000D02*
+X130175000Y-102362000D01*
+X186563000Y-57404000D02*
+X186563000Y-92456000D01*
+M02*

gerber/v1.2/bluescsi_iigs_internal-F_Mask.gbr

@@ -0,0 +1,427 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(5.1.8-0-10_14)*%
+%TF.CreationDate,2021-05-17T09:41:11-06:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Soldermask,Top*%
+%TF.FilePolarity,Negative*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (5.1.8-0-10_14)) date 2021-05-17 09:41:11*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+%ADD10C,2.100000*%
+%ADD11O,1.700000X1.700000*%
+%ADD12R,1.700000X1.700000*%
+%ADD13R,1.000000X1.500000*%
+%ADD14R,0.550000X2.910000*%
+%ADD15R,2.390000X1.050000*%
+%ADD16R,1.200000X1.050000*%
+%ADD17R,1.080000X1.050000*%
+%ADD18R,0.780000X0.720000*%
+%ADD19R,1.000000X0.500000*%
+%ADD20R,1.000000X1.000000*%
+%ADD21R,2.000000X1.500000*%
+%ADD22R,2.000000X3.800000*%
+%ADD23C,0.900000*%
+%ADD24R,1.500000X0.700000*%
+%ADD25R,0.800000X1.000000*%
+%ADD26C,1.700000*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,M2*%
+X172461000Y-48791000D03*
+X177541000Y-48791000D03*
+X172461000Y-53871000D03*
+X177541000Y-53871000D03*
+%TD*%
+%TO.C,M1*%
+X172461000Y-95481000D03*
+X177541000Y-95481000D03*
+X172461000Y-100561000D03*
+X177541000Y-100561000D03*
+%TD*%
+D11*
+%TO.C,J5*%
+X132080000Y-92075000D03*
+D12*
+X132080000Y-89535000D03*
+%TD*%
+D13*
+%TO.C,JP2*%
+X173833000Y-66548000D03*
+X175133000Y-66548000D03*
+X176433000Y-66548000D03*
+%TD*%
+%TO.C,JP1*%
+X173833000Y-61722000D03*
+X175133000Y-61722000D03*
+X176433000Y-61722000D03*
+%TD*%
+D14*
+%TO.C,J3*%
+X177524000Y-77388000D03*
+X177524000Y-73198000D03*
+D15*
+X181954000Y-80509000D03*
+D16*
+X178769000Y-80509000D03*
+X178199000Y-69859000D03*
+D17*
+X180809000Y-69859000D03*
+D18*
+X182079000Y-69874000D03*
+D19*
+X184759000Y-79334000D03*
+X184759000Y-78234000D03*
+X184759000Y-77134000D03*
+X184759000Y-76034000D03*
+X184759000Y-74934000D03*
+X184759000Y-73834000D03*
+X184759000Y-72734000D03*
+X184759000Y-71634000D03*
+%TD*%
+D20*
+%TO.C,D4*%
+X144546000Y-94488000D03*
+X147046000Y-94488000D03*
+%TD*%
+%TO.C,D3*%
+X144546000Y-98044000D03*
+X147046000Y-98044000D03*
+%TD*%
+D21*
+%TO.C,U4*%
+X135280000Y-93585000D03*
+X135280000Y-98185000D03*
+X135280000Y-95885000D03*
+D22*
+X141580000Y-95885000D03*
+%TD*%
+D11*
+%TO.C,J4*%
+X131445000Y-99060000D03*
+D12*
+X131445000Y-96520000D03*
+%TD*%
+D23*
+%TO.C,SW1*%
+X184226000Y-63095000D03*
+X184226000Y-60095000D03*
+D24*
+X182466000Y-63845000D03*
+X182466000Y-60845000D03*
+X182466000Y-59345000D03*
+D25*
+X185326000Y-65245000D03*
+X185326000Y-57945000D03*
+X183116000Y-57945000D03*
+X183116000Y-65245000D03*
+%TD*%
+%TO.C,D2*%
+G36*
+G01*
+X184981001Y-89974000D02*
+X184080999Y-89974000D01*
+G75*
+G02*
+X183831000Y-89724001I0J249999D01*
+G01*
+X183831000Y-89073999D01*
+G75*
+G02*
+X184080999Y-88824000I249999J0D01*
+G01*
+X184981001Y-88824000D01*
+G75*
+G02*
+X185231000Y-89073999I0J-249999D01*
+G01*
+X185231000Y-89724001D01*
+G75*
+G02*
+X184981001Y-89974000I-249999J0D01*
+G01*
+G37*
+G36*
+G01*
+X184981001Y-92024000D02*
+X184080999Y-92024000D01*
+G75*
+G02*
+X183831000Y-91774001I0J249999D01*
+G01*
+X183831000Y-91123999D01*
+G75*
+G02*
+X184080999Y-90874000I249999J0D01*
+G01*
+X184981001Y-90874000D01*
+G75*
+G02*
+X185231000Y-91123999I0J-249999D01*
+G01*
+X185231000Y-91774001D01*
+G75*
+G02*
+X184981001Y-92024000I-249999J0D01*
+G01*
+G37*
+%TD*%
+%TO.C,D1*%
+G36*
+G01*
+X184981001Y-84386000D02*
+X184080999Y-84386000D01*
+G75*
+G02*
+X183831000Y-84136001I0J249999D01*
+G01*
+X183831000Y-83485999D01*
+G75*
+G02*
+X184080999Y-83236000I249999J0D01*
+G01*
+X184981001Y-83236000D01*
+G75*
+G02*
+X185231000Y-83485999I0J-249999D01*
+G01*
+X185231000Y-84136001D01*
+G75*
+G02*
+X184981001Y-84386000I-249999J0D01*
+G01*
+G37*
+G36*
+G01*
+X184981001Y-86436000D02*
+X184080999Y-86436000D01*
+G75*
+G02*
+X183831000Y-86186001I0J249999D01*
+G01*
+X183831000Y-85535999D01*
+G75*
+G02*
+X184080999Y-85286000I249999J0D01*
+G01*
+X184981001Y-85286000D01*
+G75*
+G02*
+X185231000Y-85535999I0J-249999D01*
+G01*
+X185231000Y-86186001D01*
+G75*
+G02*
+X184981001Y-86436000I-249999J0D01*
+G01*
+G37*
+%TD*%
+%TO.C,R2*%
+G36*
+G01*
+X176638000Y-89211999D02*
+X176638000Y-90112001D01*
+G75*
+G02*
+X176388001Y-90362000I-249999J0D01*
+G01*
+X175687999Y-90362000D01*
+G75*
+G02*
+X175438000Y-90112001I0J249999D01*
+G01*
+X175438000Y-89211999D01*
+G75*
+G02*
+X175687999Y-88962000I249999J0D01*
+G01*
+X176388001Y-88962000D01*
+G75*
+G02*
+X176638000Y-89211999I0J-249999D01*
+G01*
+G37*
+G36*
+G01*
+X178638000Y-89211999D02*
+X178638000Y-90112001D01*
+G75*
+G02*
+X178388001Y-90362000I-249999J0D01*
+G01*
+X177687999Y-90362000D01*
+G75*
+G02*
+X177438000Y-90112001I0J249999D01*
+G01*
+X177438000Y-89211999D01*
+G75*
+G02*
+X177687999Y-88962000I249999J0D01*
+G01*
+X178388001Y-88962000D01*
+G75*
+G02*
+X178638000Y-89211999I0J-249999D01*
+G01*
+G37*
+%TD*%
+%TO.C,R1*%
+G36*
+G01*
+X177438000Y-86175001D02*
+X177438000Y-85274999D01*
+G75*
+G02*
+X177687999Y-85025000I249999J0D01*
+G01*
+X178388001Y-85025000D01*
+G75*
+G02*
+X178638000Y-85274999I0J-249999D01*
+G01*
+X178638000Y-86175001D01*
+G75*
+G02*
+X178388001Y-86425000I-249999J0D01*
+G01*
+X177687999Y-86425000D01*
+G75*
+G02*
+X177438000Y-86175001I0J249999D01*
+G01*
+G37*
+G36*
+G01*
+X175438000Y-86175001D02*
+X175438000Y-85274999D01*
+G75*
+G02*
+X175687999Y-85025000I249999J0D01*
+G01*
+X176388001Y-85025000D01*
+G75*
+G02*
+X176638000Y-85274999I0J-249999D01*
+G01*
+X176638000Y-86175001D01*
+G75*
+G02*
+X176388001Y-86425000I-249999J0D01*
+G01*
+X175687999Y-86425000D01*
+G75*
+G02*
+X175438000Y-86175001I0J249999D01*
+G01*
+G37*
+%TD*%
+D11*
+%TO.C,J2*%
+X144780000Y-85090000D03*
+X142240000Y-85090000D03*
+X144780000Y-82550000D03*
+X142240000Y-82550000D03*
+X144780000Y-80010000D03*
+X142240000Y-80010000D03*
+X144780000Y-77470000D03*
+X142240000Y-77470000D03*
+X144780000Y-74930000D03*
+X142240000Y-74930000D03*
+X144780000Y-72390000D03*
+X142240000Y-72390000D03*
+X144780000Y-69850000D03*
+X142240000Y-69850000D03*
+X144780000Y-67310000D03*
+X142240000Y-67310000D03*
+X144780000Y-64770000D03*
+X142240000Y-64770000D03*
+X144780000Y-62230000D03*
+X142240000Y-62230000D03*
+X144780000Y-59690000D03*
+X142240000Y-59690000D03*
+X144780000Y-57150000D03*
+X142240000Y-57150000D03*
+X144780000Y-54610000D03*
+D12*
+X142240000Y-54610000D03*
+%TD*%
+D26*
+%TO.C,U1*%
+X167640000Y-50800000D03*
+D12*
+X152400000Y-50800000D03*
+D26*
+X167640000Y-53340000D03*
+X152400000Y-53340000D03*
+X167640000Y-55880000D03*
+X152400000Y-55880000D03*
+X167640000Y-58420000D03*
+X152400000Y-58420000D03*
+X167640000Y-60960000D03*
+X152400000Y-60960000D03*
+X167640000Y-63500000D03*
+X152400000Y-63500000D03*
+X167640000Y-66040000D03*
+X152400000Y-66040000D03*
+X167640000Y-68580000D03*
+X152400000Y-68580000D03*
+X167640000Y-71120000D03*
+X152400000Y-71120000D03*
+X167640000Y-73660000D03*
+X152400000Y-73660000D03*
+X167640000Y-76200000D03*
+X152400000Y-76200000D03*
+X167640000Y-78740000D03*
+X152400000Y-78740000D03*
+X167640000Y-81280000D03*
+X152400000Y-81280000D03*
+X167640000Y-83820000D03*
+X152400000Y-83820000D03*
+X167640000Y-86360000D03*
+X152400000Y-86360000D03*
+X167640000Y-88900000D03*
+X152400000Y-88900000D03*
+X167640000Y-91440000D03*
+X152400000Y-91440000D03*
+X167640000Y-93980000D03*
+X152400000Y-93980000D03*
+X167640000Y-96520000D03*
+X152400000Y-96520000D03*
+X167640000Y-99060000D03*
+X152400000Y-99060000D03*
+%TD*%
+D11*
+%TO.C,J1*%
+X134620000Y-85090000D03*
+X132080000Y-85090000D03*
+X134620000Y-82550000D03*
+X132080000Y-82550000D03*
+X134620000Y-80010000D03*
+X132080000Y-80010000D03*
+X134620000Y-77470000D03*
+X132080000Y-77470000D03*
+X134620000Y-74930000D03*
+X132080000Y-74930000D03*
+X134620000Y-72390000D03*
+X132080000Y-72390000D03*
+X134620000Y-69850000D03*
+X132080000Y-69850000D03*
+X134620000Y-67310000D03*
+X132080000Y-67310000D03*
+X134620000Y-64770000D03*
+X132080000Y-64770000D03*
+X134620000Y-62230000D03*
+X132080000Y-62230000D03*
+X134620000Y-59690000D03*
+X132080000Y-59690000D03*
+X134620000Y-57150000D03*
+X132080000Y-57150000D03*
+X134620000Y-54610000D03*
+D12*
+X132080000Y-54610000D03*
+%TD*%
+M02*

gerber/v1.2/bluescsi_iigs_internal-F_Paste.gbr

@@ -0,0 +1,277 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(5.1.8-0-10_14)*%
+%TF.CreationDate,2021-05-17T09:41:11-06:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Paste,Top*%
+%TF.FilePolarity,Positive*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (5.1.8-0-10_14)) date 2021-05-17 09:41:11*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+%ADD10R,0.550000X2.910000*%
+%ADD11R,2.390000X1.050000*%
+%ADD12R,1.200000X1.050000*%
+%ADD13R,1.080000X1.050000*%
+%ADD14R,0.780000X0.720000*%
+%ADD15R,1.000000X0.500000*%
+%ADD16R,1.000000X1.000000*%
+%ADD17R,2.000000X1.500000*%
+%ADD18R,2.000000X3.800000*%
+%ADD19R,1.500000X0.700000*%
+%ADD20R,0.800000X1.000000*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,J3*%
+X177524000Y-77388000D03*
+X177524000Y-73198000D03*
+D11*
+X181954000Y-80509000D03*
+D12*
+X178769000Y-80509000D03*
+X178199000Y-69859000D03*
+D13*
+X180809000Y-69859000D03*
+D14*
+X182079000Y-69874000D03*
+D15*
+X184759000Y-79334000D03*
+X184759000Y-78234000D03*
+X184759000Y-77134000D03*
+X184759000Y-76034000D03*
+X184759000Y-74934000D03*
+X184759000Y-73834000D03*
+X184759000Y-72734000D03*
+X184759000Y-71634000D03*
+%TD*%
+D16*
+%TO.C,D4*%
+X144546000Y-94488000D03*
+X147046000Y-94488000D03*
+%TD*%
+%TO.C,D3*%
+X144546000Y-98044000D03*
+X147046000Y-98044000D03*
+%TD*%
+D17*
+%TO.C,U4*%
+X135280000Y-93585000D03*
+X135280000Y-98185000D03*
+X135280000Y-95885000D03*
+D18*
+X141580000Y-95885000D03*
+%TD*%
+D19*
+%TO.C,SW1*%
+X182466000Y-63845000D03*
+X182466000Y-60845000D03*
+X182466000Y-59345000D03*
+D20*
+X185326000Y-65245000D03*
+X185326000Y-57945000D03*
+X183116000Y-57945000D03*
+X183116000Y-65245000D03*
+%TD*%
+%TO.C,D2*%
+G36*
+G01*
+X184981001Y-89974000D02*
+X184080999Y-89974000D01*
+G75*
+G02*
+X183831000Y-89724001I0J249999D01*
+G01*
+X183831000Y-89073999D01*
+G75*
+G02*
+X184080999Y-88824000I249999J0D01*
+G01*
+X184981001Y-88824000D01*
+G75*
+G02*
+X185231000Y-89073999I0J-249999D01*
+G01*
+X185231000Y-89724001D01*
+G75*
+G02*
+X184981001Y-89974000I-249999J0D01*
+G01*
+G37*
+G36*
+G01*
+X184981001Y-92024000D02*
+X184080999Y-92024000D01*
+G75*
+G02*
+X183831000Y-91774001I0J249999D01*
+G01*
+X183831000Y-91123999D01*
+G75*
+G02*
+X184080999Y-90874000I249999J0D01*
+G01*
+X184981001Y-90874000D01*
+G75*
+G02*
+X185231000Y-91123999I0J-249999D01*
+G01*
+X185231000Y-91774001D01*
+G75*
+G02*
+X184981001Y-92024000I-249999J0D01*
+G01*
+G37*
+%TD*%
+%TO.C,D1*%
+G36*
+G01*
+X184981001Y-84386000D02*
+X184080999Y-84386000D01*
+G75*
+G02*
+X183831000Y-84136001I0J249999D01*
+G01*
+X183831000Y-83485999D01*
+G75*
+G02*
+X184080999Y-83236000I249999J0D01*
+G01*
+X184981001Y-83236000D01*
+G75*
+G02*
+X185231000Y-83485999I0J-249999D01*
+G01*
+X185231000Y-84136001D01*
+G75*
+G02*
+X184981001Y-84386000I-249999J0D01*
+G01*
+G37*
+G36*
+G01*
+X184981001Y-86436000D02*
+X184080999Y-86436000D01*
+G75*
+G02*
+X183831000Y-86186001I0J249999D01*
+G01*
+X183831000Y-85535999D01*
+G75*
+G02*
+X184080999Y-85286000I249999J0D01*
+G01*
+X184981001Y-85286000D01*
+G75*
+G02*
+X185231000Y-85535999I0J-249999D01*
+G01*
+X185231000Y-86186001D01*
+G75*
+G02*
+X184981001Y-86436000I-249999J0D01*
+G01*
+G37*
+%TD*%
+%TO.C,R2*%
+G36*
+G01*
+X176638000Y-89211999D02*
+X176638000Y-90112001D01*
+G75*
+G02*
+X176388001Y-90362000I-249999J0D01*
+G01*
+X175687999Y-90362000D01*
+G75*
+G02*
+X175438000Y-90112001I0J249999D01*
+G01*
+X175438000Y-89211999D01*
+G75*
+G02*
+X175687999Y-88962000I249999J0D01*
+G01*
+X176388001Y-88962000D01*
+G75*
+G02*
+X176638000Y-89211999I0J-249999D01*
+G01*
+G37*
+G36*
+G01*
+X178638000Y-89211999D02*
+X178638000Y-90112001D01*
+G75*
+G02*
+X178388001Y-90362000I-249999J0D01*
+G01*
+X177687999Y-90362000D01*
+G75*
+G02*
+X177438000Y-90112001I0J249999D01*
+G01*
+X177438000Y-89211999D01*
+G75*
+G02*
+X177687999Y-88962000I249999J0D01*
+G01*
+X178388001Y-88962000D01*
+G75*
+G02*
+X178638000Y-89211999I0J-249999D01*
+G01*
+G37*
+%TD*%
+%TO.C,R1*%
+G36*
+G01*
+X177438000Y-86175001D02*
+X177438000Y-85274999D01*
+G75*
+G02*
+X177687999Y-85025000I249999J0D01*
+G01*
+X178388001Y-85025000D01*
+G75*
+G02*
+X178638000Y-85274999I0J-249999D01*
+G01*
+X178638000Y-86175001D01*
+G75*
+G02*
+X178388001Y-86425000I-249999J0D01*
+G01*
+X177687999Y-86425000D01*
+G75*
+G02*
+X177438000Y-86175001I0J249999D01*
+G01*
+G37*
+G36*
+G01*
+X175438000Y-86175001D02*
+X175438000Y-85274999D01*
+G75*
+G02*
+X175687999Y-85025000I249999J0D01*
+G01*
+X176388001Y-85025000D01*
+G75*
+G02*
+X176638000Y-85274999I0J-249999D01*
+G01*
+X176638000Y-86175001D01*
+G75*
+G02*
+X176388001Y-86425000I-249999J0D01*
+G01*
+X175687999Y-86425000D01*
+G75*
+G02*
+X175438000Y-86175001I0J249999D01*
+G01*
+G37*
+%TD*%
+M02*

gerber/v1.2/bluescsi_iigs_internal-NPTH.drl

@@ -0,0 +1,17 @@
+M48
+; DRILL file {KiCad (5.1.8-0-10_14)} date Monday, May 17, 2021 at 09:41:18 AM
+; FORMAT={-:-/ absolute / inch / decimal}
+; #@! TF.CreationDate,2021-05-17T09:41:18-06:00
+; #@! TF.GenerationSoftware,Kicad,Pcbnew,(5.1.8-0-10_14)
+; #@! TF.FileFunction,NonPlated,1,2,NPTH
+FMAT,2
+INCH
+T1C0.0354
+%
+G90
+G05
+T1
+X7.253Y-2.3659
+X7.253Y-2.4841
+T0
+M30

gerber/v1.2/bluescsi_iigs_internal-PTH.drl

@@ -0,0 +1,141 @@
+M48
+; DRILL file {KiCad (5.1.8-0-10_14)} date Monday, May 17, 2021 at 09:41:18 AM
+; FORMAT={-:-/ absolute / inch / decimal}
+; #@! TF.CreationDate,2021-05-17T09:41:18-06:00
+; #@! TF.GenerationSoftware,Kicad,Pcbnew,(5.1.8-0-10_14)
+; #@! TF.FileFunction,Plated,1,2,PTH
+FMAT,2
+INCH
+T1C0.0157
+T2C0.0394
+T3C0.0669
+%
+G90
+G05
+T1
+X5.51Y-2.0
+X5.575Y-2.0
+X5.815Y-2.685
+X6.125Y-2.4
+X6.138Y-3.4
+X6.2608Y-2.4501
+X6.335Y-2.525
+X6.4Y-2.81
+X6.47Y-2.4
+X6.47Y-3.4
+X6.685Y-2.55
+X6.7Y-3.55
+X6.725Y-2.625
+X6.725Y-2.43
+X6.775Y-2.31
+X6.775Y-2.94
+X6.89Y-3.3
+X7.08Y-3.055
+T2
+X5.6Y-2.15
+X5.6Y-2.25
+X5.6Y-2.35
+X5.6Y-2.45
+X5.6Y-2.55
+X5.6Y-2.65
+X5.6Y-2.75
+X5.6Y-2.85
+X5.6Y-2.95
+X5.6Y-3.05
+X5.6Y-3.15
+X5.6Y-3.25
+X5.6Y-3.35
+X5.7Y-2.15
+X5.7Y-2.25
+X5.7Y-2.35
+X5.7Y-2.45
+X5.7Y-2.55
+X5.7Y-2.65
+X5.7Y-2.75
+X5.7Y-2.85
+X5.7Y-2.95
+X5.7Y-3.05
+X5.7Y-3.15
+X5.7Y-3.25
+X5.7Y-3.35
+X5.175Y-3.8
+X5.175Y-3.9
+X5.2Y-2.15
+X5.2Y-2.25
+X5.2Y-2.35
+X5.2Y-2.45
+X5.2Y-2.55
+X5.2Y-2.65
+X5.2Y-2.75
+X5.2Y-2.85
+X5.2Y-2.95
+X5.2Y-3.05
+X5.2Y-3.15
+X5.2Y-3.25
+X5.2Y-3.35
+X5.3Y-2.15
+X5.3Y-2.25
+X5.3Y-2.35
+X5.3Y-2.45
+X5.3Y-2.55
+X5.3Y-2.65
+X5.3Y-2.75
+X5.3Y-2.85
+X5.3Y-2.95
+X5.3Y-3.05
+X5.3Y-3.15
+X5.3Y-3.25
+X5.3Y-3.35
+X6.0Y-2.0
+X6.0Y-2.1
+X6.0Y-2.2
+X6.0Y-2.3
+X6.0Y-2.4
+X6.0Y-2.5
+X6.0Y-2.6
+X6.0Y-2.7
+X6.0Y-2.8
+X6.0Y-2.9
+X6.0Y-3.0
+X6.0Y-3.1
+X6.0Y-3.2
+X6.0Y-3.3
+X6.0Y-3.4
+X6.0Y-3.5
+X6.0Y-3.6
+X6.0Y-3.7
+X6.0Y-3.8
+X6.0Y-3.9
+X6.6Y-2.0
+X6.6Y-2.1
+X6.6Y-2.2
+X6.6Y-2.3
+X6.6Y-2.4
+X6.6Y-2.5
+X6.6Y-2.6
+X6.6Y-2.7
+X6.6Y-2.8
+X6.6Y-2.9
+X6.6Y-3.0
+X6.6Y-3.1
+X6.6Y-3.2
+X6.6Y-3.3
+X6.6Y-3.4
+X6.6Y-3.5
+X6.6Y-3.6
+X6.6Y-3.7
+X6.6Y-3.8
+X6.6Y-3.9
+X5.2Y-3.525
+X5.2Y-3.625
+T3
+X6.7898Y-1.9209
+X6.7898Y-2.1209
+X6.9898Y-1.9209
+X6.9898Y-2.1209
+X6.7898Y-3.7591
+X6.7898Y-3.9591
+X6.9898Y-3.7591
+X6.9898Y-3.9591
+T0
+M30

gerber/v1.3.1/bluescsi_iigs_internal-B_Mask.gbs

@@ -0,0 +1,275 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2022-04-27T14:28:45-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Soldermask,Bot*%
+%TF.FilePolarity,Negative*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2022-04-27 14:28:45*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 Aperture macros list*
+%AMRoundRect*
+0 Rectangle with rounded corners*
+0 $1 Rounding radius*
+0 $2 $3 $4 $5 $6 $7 $8 $9 X,Y pos of 4 corners*
+0 Add a 4 corners polygon primitive as box body*
+4,1,4,$2,$3,$4,$5,$6,$7,$8,$9,$2,$3,0*
+0 Add four circle primitives for the rounded corners*
+1,1,$1+$1,$2,$3*
+1,1,$1+$1,$4,$5*
+1,1,$1+$1,$6,$7*
+1,1,$1+$1,$8,$9*
+0 Add four rect primitives between the rounded corners*
+20,1,$1+$1,$2,$3,$4,$5,0*
+20,1,$1+$1,$4,$5,$6,$7,0*
+20,1,$1+$1,$6,$7,$8,$9,0*
+20,1,$1+$1,$8,$9,$2,$3,0*%
+G04 Aperture macros list end*
+%ADD10R,3.480000X1.846667*%
+%ADD11R,1.500000X0.400000*%
+%ADD12O,2.000000X1.905000*%
+%ADD13R,2.000000X1.905000*%
+%ADD14O,3.500000X3.500000*%
+%ADD15C,2.100000*%
+%ADD16O,1.700000X1.700000*%
+%ADD17R,1.700000X1.700000*%
+%ADD18RoundRect,0.250000X1.075000X-0.375000X1.075000X0.375000X-1.075000X0.375000X-1.075000X-0.375000X0*%
+%ADD19RoundRect,0.250000X-0.500000X-0.925000X0.500000X-0.925000X0.500000X0.925000X-0.500000X0.925000X0*%
+%ADD20C,0.900000*%
+%ADD21RoundRect,0.250000X-0.925000X0.500000X-0.925000X-0.500000X0.925000X-0.500000X0.925000X0.500000X0*%
+%ADD22C,1.700000*%
+%ADD23R,1.970000X0.600000*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,J6*%
+X127000000Y-50805000D03*
+X127000000Y-53575000D03*
+X127000000Y-56345000D03*
+X127000000Y-59115000D03*
+X127000000Y-61885000D03*
+X127000000Y-64655000D03*
+X127000000Y-67425000D03*
+X127000000Y-70195000D03*
+X127000000Y-72965000D03*
+X127000000Y-75735000D03*
+X127000000Y-78505000D03*
+X127000000Y-81275000D03*
+%TD*%
+D11*
+%TO.C,U5*%
+X171517000Y-87234000D03*
+X171517000Y-88534000D03*
+X174177000Y-88534000D03*
+X174177000Y-87884000D03*
+X174177000Y-87234000D03*
+%TD*%
+D12*
+%TO.C,U4*%
+X129540000Y-99695000D03*
+X129540000Y-97155000D03*
+D13*
+X129540000Y-94615000D03*
+D14*
+X146200000Y-97155000D03*
+%TD*%
+D15*
+%TO.C,M2*%
+X172461000Y-48791000D03*
+X177541000Y-48791000D03*
+X172461000Y-53871000D03*
+X177541000Y-53871000D03*
+%TD*%
+%TO.C,M1*%
+X172461000Y-95481000D03*
+X177541000Y-95481000D03*
+X172461000Y-100561000D03*
+X177541000Y-100561000D03*
+%TD*%
+D16*
+%TO.C,J5*%
+X129540000Y-88773000D03*
+D17*
+X129540000Y-91313000D03*
+%TD*%
+D18*
+%TO.C,F1*%
+X143510000Y-88135000D03*
+X143510000Y-90935000D03*
+%TD*%
+D16*
+%TO.C,J4*%
+X134112000Y-98425000D03*
+D17*
+X134112000Y-95885000D03*
+%TD*%
+D19*
+%TO.C,C4*%
+X138785000Y-90170000D03*
+X135535000Y-90170000D03*
+%TD*%
+D20*
+%TO.C,SW1*%
+X184226000Y-63095000D03*
+X184226000Y-60095000D03*
+%TD*%
+D21*
+%TO.C,C3*%
+X157480000Y-97002000D03*
+X157480000Y-93752000D03*
+%TD*%
+%TO.C,C2*%
+X162814000Y-97002000D03*
+X162814000Y-93752000D03*
+%TD*%
+D19*
+%TO.C,C1*%
+X160935000Y-52832000D03*
+X164185000Y-52832000D03*
+%TD*%
+D16*
+%TO.C,J2*%
+X144780000Y-85090000D03*
+X142240000Y-85090000D03*
+X144780000Y-82550000D03*
+X142240000Y-82550000D03*
+X144780000Y-80010000D03*
+X142240000Y-80010000D03*
+X144780000Y-77470000D03*
+X142240000Y-77470000D03*
+X144780000Y-74930000D03*
+X142240000Y-74930000D03*
+X144780000Y-72390000D03*
+X142240000Y-72390000D03*
+X144780000Y-69850000D03*
+X142240000Y-69850000D03*
+X144780000Y-67310000D03*
+X142240000Y-67310000D03*
+X144780000Y-64770000D03*
+X142240000Y-64770000D03*
+X144780000Y-62230000D03*
+X142240000Y-62230000D03*
+X144780000Y-59690000D03*
+X142240000Y-59690000D03*
+X144780000Y-57150000D03*
+X142240000Y-57150000D03*
+X144780000Y-54610000D03*
+D17*
+X142240000Y-54610000D03*
+%TD*%
+D22*
+%TO.C,U1*%
+X167640000Y-50800000D03*
+D17*
+X152400000Y-50800000D03*
+D22*
+X167640000Y-53340000D03*
+X152400000Y-53340000D03*
+X167640000Y-55880000D03*
+X152400000Y-55880000D03*
+X167640000Y-58420000D03*
+X152400000Y-58420000D03*
+X167640000Y-60960000D03*
+X152400000Y-60960000D03*
+X167640000Y-63500000D03*
+X152400000Y-63500000D03*
+X167640000Y-66040000D03*
+X152400000Y-66040000D03*
+X167640000Y-68580000D03*
+X152400000Y-68580000D03*
+X167640000Y-71120000D03*
+X152400000Y-71120000D03*
+X167640000Y-73660000D03*
+X152400000Y-73660000D03*
+X167640000Y-76200000D03*
+X152400000Y-76200000D03*
+X167640000Y-78740000D03*
+X152400000Y-78740000D03*
+X167640000Y-81280000D03*
+X152400000Y-81280000D03*
+X167640000Y-83820000D03*
+X152400000Y-83820000D03*
+X167640000Y-86360000D03*
+X152400000Y-86360000D03*
+X167640000Y-88900000D03*
+X152400000Y-88900000D03*
+X167640000Y-91440000D03*
+X152400000Y-91440000D03*
+X167640000Y-93980000D03*
+X152400000Y-93980000D03*
+X167640000Y-96520000D03*
+X152400000Y-96520000D03*
+X167640000Y-99060000D03*
+X152400000Y-99060000D03*
+%TD*%
+D23*
+%TO.C,U3*%
+X162495000Y-81915000D03*
+X162495000Y-83185000D03*
+X162495000Y-84455000D03*
+X162495000Y-85725000D03*
+X162495000Y-86995000D03*
+X162495000Y-88265000D03*
+X162495000Y-89535000D03*
+X162495000Y-90805000D03*
+X157545000Y-90805000D03*
+X157545000Y-89535000D03*
+X157545000Y-88265000D03*
+X157545000Y-86995000D03*
+X157545000Y-85725000D03*
+X157545000Y-84455000D03*
+X157545000Y-83185000D03*
+X157545000Y-81915000D03*
+%TD*%
+%TO.C,U2*%
+X162495000Y-56515000D03*
+X162495000Y-57785000D03*
+X162495000Y-59055000D03*
+X162495000Y-60325000D03*
+X162495000Y-61595000D03*
+X162495000Y-62865000D03*
+X162495000Y-64135000D03*
+X162495000Y-65405000D03*
+X157545000Y-65405000D03*
+X157545000Y-64135000D03*
+X157545000Y-62865000D03*
+X157545000Y-61595000D03*
+X157545000Y-60325000D03*
+X157545000Y-59055000D03*
+X157545000Y-57785000D03*
+X157545000Y-56515000D03*
+%TD*%
+D16*
+%TO.C,J1*%
+X134620000Y-85090000D03*
+X132080000Y-85090000D03*
+X134620000Y-82550000D03*
+X132080000Y-82550000D03*
+X134620000Y-80010000D03*
+X132080000Y-80010000D03*
+X134620000Y-77470000D03*
+X132080000Y-77470000D03*
+X134620000Y-74930000D03*
+X132080000Y-74930000D03*
+X134620000Y-72390000D03*
+X132080000Y-72390000D03*
+X134620000Y-69850000D03*
+X132080000Y-69850000D03*
+X134620000Y-67310000D03*
+X132080000Y-67310000D03*
+X134620000Y-64770000D03*
+X132080000Y-64770000D03*
+X134620000Y-62230000D03*
+X132080000Y-62230000D03*
+X134620000Y-59690000D03*
+X132080000Y-59690000D03*
+X134620000Y-57150000D03*
+X132080000Y-57150000D03*
+X134620000Y-54610000D03*
+D17*
+X132080000Y-54610000D03*
+%TD*%
+M02*

gerber/v1.3.1/bluescsi_iigs_internal-B_Paste.gbp

@@ -0,0 +1,123 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2022-04-27T14:28:45-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Paste,Bot*%
+%TF.FilePolarity,Positive*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2022-04-27 14:28:45*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 Aperture macros list*
+%AMRoundRect*
+0 Rectangle with rounded corners*
+0 $1 Rounding radius*
+0 $2 $3 $4 $5 $6 $7 $8 $9 X,Y pos of 4 corners*
+0 Add a 4 corners polygon primitive as box body*
+4,1,4,$2,$3,$4,$5,$6,$7,$8,$9,$2,$3,0*
+0 Add four circle primitives for the rounded corners*
+1,1,$1+$1,$2,$3*
+1,1,$1+$1,$4,$5*
+1,1,$1+$1,$6,$7*
+1,1,$1+$1,$8,$9*
+0 Add four rect primitives between the rounded corners*
+20,1,$1+$1,$2,$3,$4,$5,0*
+20,1,$1+$1,$4,$5,$6,$7,0*
+20,1,$1+$1,$6,$7,$8,$9,0*
+20,1,$1+$1,$8,$9,$2,$3,0*%
+G04 Aperture macros list end*
+%ADD10R,3.480000X1.846667*%
+%ADD11R,1.500000X0.400000*%
+%ADD12RoundRect,0.250000X1.075000X-0.375000X1.075000X0.375000X-1.075000X0.375000X-1.075000X-0.375000X0*%
+%ADD13RoundRect,0.250000X-0.500000X-0.925000X0.500000X-0.925000X0.500000X0.925000X-0.500000X0.925000X0*%
+%ADD14RoundRect,0.250000X-0.925000X0.500000X-0.925000X-0.500000X0.925000X-0.500000X0.925000X0.500000X0*%
+%ADD15R,1.970000X0.600000*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,J6*%
+X127000000Y-50805000D03*
+X127000000Y-53575000D03*
+X127000000Y-56345000D03*
+X127000000Y-59115000D03*
+X127000000Y-61885000D03*
+X127000000Y-64655000D03*
+X127000000Y-67425000D03*
+X127000000Y-70195000D03*
+X127000000Y-72965000D03*
+X127000000Y-75735000D03*
+X127000000Y-78505000D03*
+X127000000Y-81275000D03*
+%TD*%
+D11*
+%TO.C,U5*%
+X171517000Y-87234000D03*
+X171517000Y-88534000D03*
+X174177000Y-88534000D03*
+X174177000Y-87884000D03*
+X174177000Y-87234000D03*
+%TD*%
+D12*
+%TO.C,F1*%
+X143510000Y-88135000D03*
+X143510000Y-90935000D03*
+%TD*%
+D13*
+%TO.C,C4*%
+X138785000Y-90170000D03*
+X135535000Y-90170000D03*
+%TD*%
+D14*
+%TO.C,C3*%
+X157480000Y-97002000D03*
+X157480000Y-93752000D03*
+%TD*%
+%TO.C,C2*%
+X162814000Y-97002000D03*
+X162814000Y-93752000D03*
+%TD*%
+D13*
+%TO.C,C1*%
+X160935000Y-52832000D03*
+X164185000Y-52832000D03*
+%TD*%
+D15*
+%TO.C,U3*%
+X162495000Y-81915000D03*
+X162495000Y-83185000D03*
+X162495000Y-84455000D03*
+X162495000Y-85725000D03*
+X162495000Y-86995000D03*
+X162495000Y-88265000D03*
+X162495000Y-89535000D03*
+X162495000Y-90805000D03*
+X157545000Y-90805000D03*
+X157545000Y-89535000D03*
+X157545000Y-88265000D03*
+X157545000Y-86995000D03*
+X157545000Y-85725000D03*
+X157545000Y-84455000D03*
+X157545000Y-83185000D03*
+X157545000Y-81915000D03*
+%TD*%
+%TO.C,U2*%
+X162495000Y-56515000D03*
+X162495000Y-57785000D03*
+X162495000Y-59055000D03*
+X162495000Y-60325000D03*
+X162495000Y-61595000D03*
+X162495000Y-62865000D03*
+X162495000Y-64135000D03*
+X162495000Y-65405000D03*
+X157545000Y-65405000D03*
+X157545000Y-64135000D03*
+X157545000Y-62865000D03*
+X157545000Y-61595000D03*
+X157545000Y-60325000D03*
+X157545000Y-59055000D03*
+X157545000Y-57785000D03*
+X157545000Y-56515000D03*
+%TD*%
+M02*

gerber/v1.3.1/bluescsi_iigs_internal-Edge_Cuts.gm1

@@ -0,0 +1,74 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2022-04-27T14:28:45-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Profile,NP*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2022-04-27 14:28:45*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+%TA.AperFunction,Profile*%
+%ADD10C,0.050000*%
+%TD*%
+G04 APERTURE END LIST*
+D10*
+X181991000Y-93726000D02*
+G75*
+G03*
+X180721000Y-94996000I0J-1270000D01*
+G01*
+X180721000Y-54864000D02*
+G75*
+G03*
+X181991000Y-56134000I1270000J0D01*
+G01*
+X186563000Y-57404000D02*
+G75*
+G03*
+X185293000Y-56134000I-1270000J0D01*
+G01*
+X185293000Y-93726000D02*
+G75*
+G03*
+X186563000Y-92456000I0J1270000D01*
+G01*
+X125095000Y-101092000D02*
+G75*
+G03*
+X126365000Y-102362000I1270000J0D01*
+G01*
+X179451000Y-102362000D02*
+G75*
+G03*
+X180721000Y-101092000I0J1270000D01*
+G01*
+X180721000Y-48260000D02*
+G75*
+G03*
+X179451000Y-46990000I-1270000J0D01*
+G01*
+X126365000Y-46990000D02*
+G75*
+G03*
+X125095000Y-48260000I0J-1270000D01*
+G01*
+X181991000Y-93726000D02*
+X185293000Y-93726000D01*
+X180721000Y-94996000D02*
+X180721000Y-101092000D01*
+X181991000Y-56134000D02*
+X185293000Y-56134000D01*
+X180721000Y-48260000D02*
+X180721000Y-54864000D01*
+X126365000Y-46990000D02*
+X179451000Y-46990000D01*
+X125095000Y-101092000D02*
+X125095000Y-48260000D01*
+X179451000Y-102362000D02*
+X126365000Y-102362000D01*
+X186563000Y-57404000D02*
+X186563000Y-92456000D01*
+M02*

gerber/v1.3.1/bluescsi_iigs_internal-F_Mask.gts

@@ -0,0 +1,288 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2022-04-27T14:28:45-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Soldermask,Top*%
+%TF.FilePolarity,Negative*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2022-04-27 14:28:45*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 Aperture macros list*
+%AMRoundRect*
+0 Rectangle with rounded corners*
+0 $1 Rounding radius*
+0 $2 $3 $4 $5 $6 $7 $8 $9 X,Y pos of 4 corners*
+0 Add a 4 corners polygon primitive as box body*
+4,1,4,$2,$3,$4,$5,$6,$7,$8,$9,$2,$3,0*
+0 Add four circle primitives for the rounded corners*
+1,1,$1+$1,$2,$3*
+1,1,$1+$1,$4,$5*
+1,1,$1+$1,$6,$7*
+1,1,$1+$1,$8,$9*
+0 Add four rect primitives between the rounded corners*
+20,1,$1+$1,$2,$3,$4,$5,0*
+20,1,$1+$1,$4,$5,$6,$7,0*
+20,1,$1+$1,$6,$7,$8,$9,0*
+20,1,$1+$1,$8,$9,$2,$3,0*%
+G04 Aperture macros list end*
+%ADD10R,3.480000X1.846667*%
+%ADD11O,2.000000X1.905000*%
+%ADD12R,2.000000X1.905000*%
+%ADD13O,3.500000X3.500000*%
+%ADD14C,2.100000*%
+%ADD15O,1.700000X1.700000*%
+%ADD16R,1.700000X1.700000*%
+%ADD17R,1.000000X1.500000*%
+%ADD18R,1.000000X0.500000*%
+%ADD19R,0.780000X0.720000*%
+%ADD20R,1.080000X1.050000*%
+%ADD21R,1.200000X1.050000*%
+%ADD22R,2.390000X1.050000*%
+%ADD23R,0.550000X2.910000*%
+%ADD24R,1.000000X1.000000*%
+%ADD25C,0.900000*%
+%ADD26R,1.500000X0.700000*%
+%ADD27R,0.800000X1.000000*%
+%ADD28RoundRect,0.249999X0.450001X-0.325001X0.450001X0.325001X-0.450001X0.325001X-0.450001X-0.325001X0*%
+%ADD29RoundRect,0.249999X-0.450001X0.325001X-0.450001X-0.325001X0.450001X-0.325001X0.450001X0.325001X0*%
+%ADD30RoundRect,0.249999X0.350001X0.450001X-0.350001X0.450001X-0.350001X-0.450001X0.350001X-0.450001X0*%
+%ADD31RoundRect,0.249999X-0.350001X-0.450001X0.350001X-0.450001X0.350001X0.450001X-0.350001X0.450001X0*%
+%ADD32C,1.700000*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,J6*%
+X127000000Y-49420000D03*
+X127000000Y-52190000D03*
+X127000000Y-54960000D03*
+X127000000Y-57730000D03*
+X127000000Y-60500000D03*
+X127000000Y-63270000D03*
+X127000000Y-66040000D03*
+X127000000Y-68810000D03*
+X127000000Y-71580000D03*
+X127000000Y-74350000D03*
+X127000000Y-77120000D03*
+X127000000Y-79890000D03*
+X127000000Y-82660000D03*
+%TD*%
+D11*
+%TO.C,U4*%
+X129540000Y-99695000D03*
+X129540000Y-97155000D03*
+D12*
+X129540000Y-94615000D03*
+D13*
+X146200000Y-97155000D03*
+%TD*%
+D14*
+%TO.C,M2*%
+X172461000Y-48791000D03*
+X177541000Y-48791000D03*
+X172461000Y-53871000D03*
+X177541000Y-53871000D03*
+%TD*%
+%TO.C,M1*%
+X172461000Y-95481000D03*
+X177541000Y-95481000D03*
+X172461000Y-100561000D03*
+X177541000Y-100561000D03*
+%TD*%
+D15*
+%TO.C,J5*%
+X129540000Y-88773000D03*
+D16*
+X129540000Y-91313000D03*
+%TD*%
+D17*
+%TO.C,JP2*%
+X173833000Y-66548000D03*
+X175133000Y-66548000D03*
+X176433000Y-66548000D03*
+%TD*%
+%TO.C,JP1*%
+X173833000Y-61722000D03*
+X175133000Y-61722000D03*
+X176433000Y-61722000D03*
+%TD*%
+D18*
+%TO.C,J3*%
+X181965000Y-71634000D03*
+X181965000Y-72734000D03*
+X181965000Y-73834000D03*
+X181965000Y-74934000D03*
+X181965000Y-76034000D03*
+X181965000Y-77134000D03*
+X181965000Y-78234000D03*
+X181965000Y-79334000D03*
+D19*
+X179285000Y-69874000D03*
+D20*
+X178015000Y-69859000D03*
+D21*
+X175405000Y-69859000D03*
+X175975000Y-80509000D03*
+D22*
+X179160000Y-80509000D03*
+D23*
+X174730000Y-73198000D03*
+X174730000Y-77388000D03*
+%TD*%
+D24*
+%TO.C,D4*%
+X137180000Y-97155000D03*
+X139680000Y-97155000D03*
+%TD*%
+%TO.C,D3*%
+X139466000Y-100330000D03*
+X141966000Y-100330000D03*
+%TD*%
+D15*
+%TO.C,J4*%
+X134112000Y-98425000D03*
+D16*
+X134112000Y-95885000D03*
+%TD*%
+D25*
+%TO.C,SW1*%
+X184226000Y-63095000D03*
+X184226000Y-60095000D03*
+D26*
+X182466000Y-63845000D03*
+X182466000Y-60845000D03*
+X182466000Y-59345000D03*
+D27*
+X185326000Y-65245000D03*
+X185326000Y-57945000D03*
+X183116000Y-57945000D03*
+X183116000Y-65245000D03*
+%TD*%
+D28*
+%TO.C,D2*%
+X184531000Y-89399000D03*
+X184531000Y-91449000D03*
+%TD*%
+D29*
+%TO.C,D1*%
+X184531000Y-85861000D03*
+X184531000Y-83811000D03*
+%TD*%
+D30*
+%TO.C,R2*%
+X176927000Y-89408000D03*
+X178927000Y-89408000D03*
+%TD*%
+D31*
+%TO.C,R1*%
+X178927000Y-85725000D03*
+X176927000Y-85725000D03*
+%TD*%
+D15*
+%TO.C,J2*%
+X144780000Y-85090000D03*
+X142240000Y-85090000D03*
+X144780000Y-82550000D03*
+X142240000Y-82550000D03*
+X144780000Y-80010000D03*
+X142240000Y-80010000D03*
+X144780000Y-77470000D03*
+X142240000Y-77470000D03*
+X144780000Y-74930000D03*
+X142240000Y-74930000D03*
+X144780000Y-72390000D03*
+X142240000Y-72390000D03*
+X144780000Y-69850000D03*
+X142240000Y-69850000D03*
+X144780000Y-67310000D03*
+X142240000Y-67310000D03*
+X144780000Y-64770000D03*
+X142240000Y-64770000D03*
+X144780000Y-62230000D03*
+X142240000Y-62230000D03*
+X144780000Y-59690000D03*
+X142240000Y-59690000D03*
+X144780000Y-57150000D03*
+X142240000Y-57150000D03*
+X144780000Y-54610000D03*
+D16*
+X142240000Y-54610000D03*
+%TD*%
+D32*
+%TO.C,U1*%
+X167640000Y-50800000D03*
+D16*
+X152400000Y-50800000D03*
+D32*
+X167640000Y-53340000D03*
+X152400000Y-53340000D03*
+X167640000Y-55880000D03*
+X152400000Y-55880000D03*
+X167640000Y-58420000D03*
+X152400000Y-58420000D03*
+X167640000Y-60960000D03*
+X152400000Y-60960000D03*
+X167640000Y-63500000D03*
+X152400000Y-63500000D03*
+X167640000Y-66040000D03*
+X152400000Y-66040000D03*
+X167640000Y-68580000D03*
+X152400000Y-68580000D03*
+X167640000Y-71120000D03*
+X152400000Y-71120000D03*
+X167640000Y-73660000D03*
+X152400000Y-73660000D03*
+X167640000Y-76200000D03*
+X152400000Y-76200000D03*
+X167640000Y-78740000D03*
+X152400000Y-78740000D03*
+X167640000Y-81280000D03*
+X152400000Y-81280000D03*
+X167640000Y-83820000D03*
+X152400000Y-83820000D03*
+X167640000Y-86360000D03*
+X152400000Y-86360000D03*
+X167640000Y-88900000D03*
+X152400000Y-88900000D03*
+X167640000Y-91440000D03*
+X152400000Y-91440000D03*
+X167640000Y-93980000D03*
+X152400000Y-93980000D03*
+X167640000Y-96520000D03*
+X152400000Y-96520000D03*
+X167640000Y-99060000D03*
+X152400000Y-99060000D03*
+%TD*%
+D15*
+%TO.C,J1*%
+X134620000Y-85090000D03*
+X132080000Y-85090000D03*
+X134620000Y-82550000D03*
+X132080000Y-82550000D03*
+X134620000Y-80010000D03*
+X132080000Y-80010000D03*
+X134620000Y-77470000D03*
+X132080000Y-77470000D03*
+X134620000Y-74930000D03*
+X132080000Y-74930000D03*
+X134620000Y-72390000D03*
+X132080000Y-72390000D03*
+X134620000Y-69850000D03*
+X132080000Y-69850000D03*
+X134620000Y-67310000D03*
+X132080000Y-67310000D03*
+X134620000Y-64770000D03*
+X132080000Y-64770000D03*
+X134620000Y-62230000D03*
+X132080000Y-62230000D03*
+X134620000Y-59690000D03*
+X132080000Y-59690000D03*
+X134620000Y-57150000D03*
+X132080000Y-57150000D03*
+X134620000Y-54610000D03*
+D16*
+X132080000Y-54610000D03*
+%TD*%
+M02*

gerber/v1.3.1/bluescsi_iigs_internal-F_Paste.gtp

@@ -0,0 +1,126 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2022-04-27T14:28:45-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Paste,Top*%
+%TF.FilePolarity,Positive*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2022-04-27 14:28:45*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 Aperture macros list*
+%AMRoundRect*
+0 Rectangle with rounded corners*
+0 $1 Rounding radius*
+0 $2 $3 $4 $5 $6 $7 $8 $9 X,Y pos of 4 corners*
+0 Add a 4 corners polygon primitive as box body*
+4,1,4,$2,$3,$4,$5,$6,$7,$8,$9,$2,$3,0*
+0 Add four circle primitives for the rounded corners*
+1,1,$1+$1,$2,$3*
+1,1,$1+$1,$4,$5*
+1,1,$1+$1,$6,$7*
+1,1,$1+$1,$8,$9*
+0 Add four rect primitives between the rounded corners*
+20,1,$1+$1,$2,$3,$4,$5,0*
+20,1,$1+$1,$4,$5,$6,$7,0*
+20,1,$1+$1,$6,$7,$8,$9,0*
+20,1,$1+$1,$8,$9,$2,$3,0*%
+G04 Aperture macros list end*
+%ADD10R,3.480000X1.846667*%
+%ADD11R,1.000000X0.500000*%
+%ADD12R,0.780000X0.720000*%
+%ADD13R,1.080000X1.050000*%
+%ADD14R,1.200000X1.050000*%
+%ADD15R,2.390000X1.050000*%
+%ADD16R,0.550000X2.910000*%
+%ADD17R,1.000000X1.000000*%
+%ADD18R,1.500000X0.700000*%
+%ADD19R,0.800000X1.000000*%
+%ADD20RoundRect,0.249999X0.450001X-0.325001X0.450001X0.325001X-0.450001X0.325001X-0.450001X-0.325001X0*%
+%ADD21RoundRect,0.249999X-0.450001X0.325001X-0.450001X-0.325001X0.450001X-0.325001X0.450001X0.325001X0*%
+%ADD22RoundRect,0.249999X0.350001X0.450001X-0.350001X0.450001X-0.350001X-0.450001X0.350001X-0.450001X0*%
+%ADD23RoundRect,0.249999X-0.350001X-0.450001X0.350001X-0.450001X0.350001X0.450001X-0.350001X0.450001X0*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,J6*%
+X127000000Y-49420000D03*
+X127000000Y-52190000D03*
+X127000000Y-54960000D03*
+X127000000Y-57730000D03*
+X127000000Y-60500000D03*
+X127000000Y-63270000D03*
+X127000000Y-66040000D03*
+X127000000Y-68810000D03*
+X127000000Y-71580000D03*
+X127000000Y-74350000D03*
+X127000000Y-77120000D03*
+X127000000Y-79890000D03*
+X127000000Y-82660000D03*
+%TD*%
+D11*
+%TO.C,J3*%
+X181965000Y-71634000D03*
+X181965000Y-72734000D03*
+X181965000Y-73834000D03*
+X181965000Y-74934000D03*
+X181965000Y-76034000D03*
+X181965000Y-77134000D03*
+X181965000Y-78234000D03*
+X181965000Y-79334000D03*
+D12*
+X179285000Y-69874000D03*
+D13*
+X178015000Y-69859000D03*
+D14*
+X175405000Y-69859000D03*
+X175975000Y-80509000D03*
+D15*
+X179160000Y-80509000D03*
+D16*
+X174730000Y-73198000D03*
+X174730000Y-77388000D03*
+%TD*%
+D17*
+%TO.C,D4*%
+X137180000Y-97155000D03*
+X139680000Y-97155000D03*
+%TD*%
+%TO.C,D3*%
+X139466000Y-100330000D03*
+X141966000Y-100330000D03*
+%TD*%
+D18*
+%TO.C,SW1*%
+X182466000Y-63845000D03*
+X182466000Y-60845000D03*
+X182466000Y-59345000D03*
+D19*
+X185326000Y-65245000D03*
+X185326000Y-57945000D03*
+X183116000Y-57945000D03*
+X183116000Y-65245000D03*
+%TD*%
+D20*
+%TO.C,D2*%
+X184531000Y-89399000D03*
+X184531000Y-91449000D03*
+%TD*%
+D21*
+%TO.C,D1*%
+X184531000Y-85861000D03*
+X184531000Y-83811000D03*
+%TD*%
+D22*
+%TO.C,R2*%
+X176927000Y-89408000D03*
+X178927000Y-89408000D03*
+%TD*%
+D23*
+%TO.C,R1*%
+X178927000Y-85725000D03*
+X176927000Y-85725000D03*
+%TD*%
+M02*

gerber/v1.3.1/bluescsi_iigs_internal-NPTH.drl

@@ -0,0 +1,22 @@
+M48
+; DRILL file {KiCad (6.0.4-0)} date Wednesday, April 27, 2022 at 02:28:39 PM
+; FORMAT={-:-/ absolute / metric / decimal}
+; #@! TF.CreationDate,2022-04-27T14:28:39-07:00
+; #@! TF.GenerationSoftware,Kicad,Pcbnew,(6.0.4-0)
+; #@! TF.FileFunction,NonPlated,1,2,NPTH
+FMAT,2
+METRIC
+; #@! TA.AperFunction,NonPlated,NPTH,ComponentDrill
+T1C0.900
+; #@! TA.AperFunction,NonPlated,NPTH,ComponentDrill
+T2C3.500
+%
+G90
+G05
+T1
+X184.226Y-60.095
+X184.226Y-63.095
+T2
+X146.2Y-97.155
+T0
+M30

gerber/v1.3.1/bluescsi_iigs_internal-PTH.drl

@@ -0,0 +1,154 @@
+M48
+; DRILL file {KiCad (6.0.4-0)} date Wednesday, April 27, 2022 at 02:28:39 PM
+; FORMAT={-:-/ absolute / metric / decimal}
+; #@! TF.CreationDate,2022-04-27T14:28:39-07:00
+; #@! TF.GenerationSoftware,Kicad,Pcbnew,(6.0.4-0)
+; #@! TF.FileFunction,Plated,1,2,PTH
+FMAT,2
+METRIC
+; #@! TA.AperFunction,Plated,PTH,ViaDrill
+T1C0.400
+; #@! TA.AperFunction,Plated,PTH,ComponentDrill
+T2C1.000
+; #@! TA.AperFunction,Plated,PTH,ComponentDrill
+T3C1.100
+; #@! TA.AperFunction,Plated,PTH,ComponentDrill
+T4C1.700
+%
+G90
+G05
+T1
+X139.954Y-50.8
+X140.589Y-93.345
+X141.605Y-50.8
+X147.701Y-68.199
+X155.575Y-60.96
+X155.905Y-86.36
+X156.845Y-52.705
+X159.025Y-62.234
+X160.909Y-64.135
+X162.433Y-67.818
+X164.338Y-60.96
+X164.338Y-86.36
+X169.799Y-64.77
+X170.307Y-85.979
+X170.561Y-73.279
+X170.815Y-66.675
+X170.815Y-61.722
+X171.45Y-83.947
+X171.577Y-58.674
+X172.847Y-83.82
+X176.657Y-77.47
+X182.245Y-87.63
+T2
+X129.54Y-88.773
+X129.54Y-91.313
+X132.08Y-54.61
+X132.08Y-57.15
+X132.08Y-59.69
+X132.08Y-62.23
+X132.08Y-64.77
+X132.08Y-67.31
+X132.08Y-69.85
+X132.08Y-72.39
+X132.08Y-74.93
+X132.08Y-77.47
+X132.08Y-80.01
+X132.08Y-82.55
+X132.08Y-85.09
+X134.112Y-95.885
+X134.112Y-98.425
+X134.62Y-54.61
+X134.62Y-57.15
+X134.62Y-59.69
+X134.62Y-62.23
+X134.62Y-64.77
+X134.62Y-67.31
+X134.62Y-69.85
+X134.62Y-72.39
+X134.62Y-74.93
+X134.62Y-77.47
+X134.62Y-80.01
+X134.62Y-82.55
+X134.62Y-85.09
+X142.24Y-54.61
+X142.24Y-57.15
+X142.24Y-59.69
+X142.24Y-62.23
+X142.24Y-64.77
+X142.24Y-67.31
+X142.24Y-69.85
+X142.24Y-72.39
+X142.24Y-74.93
+X142.24Y-77.47
+X142.24Y-80.01
+X142.24Y-82.55
+X142.24Y-85.09
+X144.78Y-54.61
+X144.78Y-57.15
+X144.78Y-59.69
+X144.78Y-62.23
+X144.78Y-64.77
+X144.78Y-67.31
+X144.78Y-69.85
+X144.78Y-72.39
+X144.78Y-74.93
+X144.78Y-77.47
+X144.78Y-80.01
+X144.78Y-82.55
+X144.78Y-85.09
+X152.4Y-50.8
+X152.4Y-53.34
+X152.4Y-55.88
+X152.4Y-58.42
+X152.4Y-60.96
+X152.4Y-63.5
+X152.4Y-66.04
+X152.4Y-68.58
+X152.4Y-71.12
+X152.4Y-73.66
+X152.4Y-76.2
+X152.4Y-78.74
+X152.4Y-81.28
+X152.4Y-83.82
+X152.4Y-86.36
+X152.4Y-88.9
+X152.4Y-91.44
+X152.4Y-93.98
+X152.4Y-96.52
+X152.4Y-99.06
+X167.64Y-50.8
+X167.64Y-53.34
+X167.64Y-55.88
+X167.64Y-58.42
+X167.64Y-60.96
+X167.64Y-63.5
+X167.64Y-66.04
+X167.64Y-68.58
+X167.64Y-71.12
+X167.64Y-73.66
+X167.64Y-76.2
+X167.64Y-78.74
+X167.64Y-81.28
+X167.64Y-83.82
+X167.64Y-86.36
+X167.64Y-88.9
+X167.64Y-91.44
+X167.64Y-93.98
+X167.64Y-96.52
+X167.64Y-99.06
+T3
+X129.54Y-94.615
+X129.54Y-97.155
+X129.54Y-99.695
+T4
+X172.461Y-48.791
+X172.461Y-53.871
+X172.461Y-95.481
+X172.461Y-100.561
+X177.541Y-48.791
+X177.541Y-53.871
+X177.541Y-95.481
+X177.541Y-100.561
+T0
+M30

gerber/v1.3.1/bluescsi_iigs_internal-User_Eco1.gbr

@@ -0,0 +1,14 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2022-04-27T14:28:45-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Other,ECO1*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2022-04-27 14:28:45*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 APERTURE END LIST*
+M02*

gerber/v1.3.1/bluescsi_iigs_internal-User_Eco2.gbr

@@ -0,0 +1,14 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2022-04-27T14:28:45-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Other,ECO2*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2022-04-27 14:28:45*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 APERTURE END LIST*
+M02*

gerber/v1.4/bluescsi_iigs_internal-B_Mask.gbs

@@ -0,0 +1,265 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2023-01-26T09:36:58-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Soldermask,Bot*%
+%TF.FilePolarity,Negative*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2023-01-26 09:36:58*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 Aperture macros list*
+%AMRoundRect*
+0 Rectangle with rounded corners*
+0 $1 Rounding radius*
+0 $2 $3 $4 $5 $6 $7 $8 $9 X,Y pos of 4 corners*
+0 Add a 4 corners polygon primitive as box body*
+4,1,4,$2,$3,$4,$5,$6,$7,$8,$9,$2,$3,0*
+0 Add four circle primitives for the rounded corners*
+1,1,$1+$1,$2,$3*
+1,1,$1+$1,$4,$5*
+1,1,$1+$1,$6,$7*
+1,1,$1+$1,$8,$9*
+0 Add four rect primitives between the rounded corners*
+20,1,$1+$1,$2,$3,$4,$5,0*
+20,1,$1+$1,$4,$5,$6,$7,0*
+20,1,$1+$1,$6,$7,$8,$9,0*
+20,1,$1+$1,$8,$9,$2,$3,0*%
+G04 Aperture macros list end*
+%ADD10R,1.700000X1.700000*%
+%ADD11C,1.700000*%
+%ADD12C,0.900000*%
+%ADD13O,1.700000X1.700000*%
+%ADD14C,2.100000*%
+%ADD15R,3.480000X1.846667*%
+%ADD16RoundRect,0.250000X-0.500000X-0.925000X0.500000X-0.925000X0.500000X0.925000X-0.500000X0.925000X0*%
+%ADD17R,1.970000X0.600000*%
+%ADD18RoundRect,0.250000X0.500000X0.925000X-0.500000X0.925000X-0.500000X-0.925000X0.500000X-0.925000X0*%
+%ADD19RoundRect,0.250000X1.075000X-0.375000X1.075000X0.375000X-1.075000X0.375000X-1.075000X-0.375000X0*%
+%ADD20R,1.500000X0.400000*%
+%ADD21RoundRect,0.250000X0.925000X-0.500000X0.925000X0.500000X-0.925000X0.500000X-0.925000X-0.500000X0*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,U1*%
+X152400000Y-50800000D03*
+D11*
+X152400000Y-53340000D03*
+X152400000Y-55880000D03*
+X152400000Y-58420000D03*
+X152400000Y-60960000D03*
+X152400000Y-63500000D03*
+X152400000Y-66040000D03*
+X152400000Y-68580000D03*
+X152400000Y-71120000D03*
+X152400000Y-73660000D03*
+X152400000Y-76200000D03*
+X152400000Y-78740000D03*
+X152400000Y-81280000D03*
+X152400000Y-83820000D03*
+X152400000Y-86360000D03*
+X152400000Y-88900000D03*
+X152400000Y-91440000D03*
+X152400000Y-93980000D03*
+X152400000Y-96520000D03*
+X152400000Y-99060000D03*
+X167640000Y-99060000D03*
+X167640000Y-96520000D03*
+X167640000Y-93980000D03*
+X167640000Y-91440000D03*
+X167640000Y-88900000D03*
+X167640000Y-86360000D03*
+X167640000Y-83820000D03*
+X167640000Y-81280000D03*
+X167640000Y-78740000D03*
+X167640000Y-76200000D03*
+X167640000Y-73660000D03*
+X167640000Y-71120000D03*
+X167640000Y-68580000D03*
+X167640000Y-66040000D03*
+X167640000Y-63500000D03*
+X167640000Y-60960000D03*
+X167640000Y-58420000D03*
+X167640000Y-55880000D03*
+X167640000Y-53340000D03*
+X167640000Y-50800000D03*
+%TD*%
+D12*
+%TO.C,SW1*%
+X184226000Y-63095000D03*
+X184226000Y-60095000D03*
+%TD*%
+D10*
+%TO.C,J1*%
+X132080000Y-54610000D03*
+D13*
+X134620000Y-54610000D03*
+X132080000Y-57150000D03*
+X134620000Y-57150000D03*
+X132080000Y-59690000D03*
+X134620000Y-59690000D03*
+X132080000Y-62230000D03*
+X134620000Y-62230000D03*
+X132080000Y-64770000D03*
+X134620000Y-64770000D03*
+X132080000Y-67310000D03*
+X134620000Y-67310000D03*
+X132080000Y-69850000D03*
+X134620000Y-69850000D03*
+X132080000Y-72390000D03*
+X134620000Y-72390000D03*
+X132080000Y-74930000D03*
+X134620000Y-74930000D03*
+X132080000Y-77470000D03*
+X134620000Y-77470000D03*
+X132080000Y-80010000D03*
+X134620000Y-80010000D03*
+X132080000Y-82550000D03*
+X134620000Y-82550000D03*
+X132080000Y-85090000D03*
+X134620000Y-85090000D03*
+%TD*%
+D10*
+%TO.C,J2*%
+X142240000Y-54610000D03*
+D13*
+X144780000Y-54610000D03*
+X142240000Y-57150000D03*
+X144780000Y-57150000D03*
+X142240000Y-59690000D03*
+X144780000Y-59690000D03*
+X142240000Y-62230000D03*
+X144780000Y-62230000D03*
+X142240000Y-64770000D03*
+X144780000Y-64770000D03*
+X142240000Y-67310000D03*
+X144780000Y-67310000D03*
+X142240000Y-69850000D03*
+X144780000Y-69850000D03*
+X142240000Y-72390000D03*
+X144780000Y-72390000D03*
+X142240000Y-74930000D03*
+X144780000Y-74930000D03*
+X142240000Y-77470000D03*
+X144780000Y-77470000D03*
+X142240000Y-80010000D03*
+X144780000Y-80010000D03*
+X142240000Y-82550000D03*
+X144780000Y-82550000D03*
+X142240000Y-85090000D03*
+X144780000Y-85090000D03*
+%TD*%
+D10*
+%TO.C,J4*%
+X128905000Y-97536000D03*
+D13*
+X128905000Y-100076000D03*
+%TD*%
+D10*
+%TO.C,J5*%
+X127889000Y-92964000D03*
+D13*
+X127889000Y-90424000D03*
+%TD*%
+D14*
+%TO.C,M1*%
+X177591000Y-95481000D03*
+X177591000Y-100561000D03*
+X172511000Y-95481000D03*
+X172511000Y-100561000D03*
+%TD*%
+%TO.C,M2*%
+X177591000Y-48791000D03*
+X172511000Y-48791000D03*
+X177591000Y-53871000D03*
+X172511000Y-53871000D03*
+%TD*%
+D15*
+%TO.C,J6*%
+X127000000Y-50805000D03*
+X127000000Y-53575000D03*
+X127000000Y-56345000D03*
+X127000000Y-59115000D03*
+X127000000Y-61885000D03*
+X127000000Y-64655000D03*
+X127000000Y-67425000D03*
+X127000000Y-70195000D03*
+X127000000Y-72965000D03*
+X127000000Y-75735000D03*
+X127000000Y-78505000D03*
+X127000000Y-81275000D03*
+%TD*%
+D16*
+%TO.C,C1*%
+X160935000Y-52324000D03*
+X164185000Y-52324000D03*
+%TD*%
+D17*
+%TO.C,U3*%
+X162495000Y-81915000D03*
+X162495000Y-83185000D03*
+X162495000Y-84455000D03*
+X162495000Y-85725000D03*
+X162495000Y-86995000D03*
+X162495000Y-88265000D03*
+X162495000Y-89535000D03*
+X162495000Y-90805000D03*
+X157545000Y-90805000D03*
+X157545000Y-89535000D03*
+X157545000Y-88265000D03*
+X157545000Y-86995000D03*
+X157545000Y-85725000D03*
+X157545000Y-84455000D03*
+X157545000Y-83185000D03*
+X157545000Y-81915000D03*
+%TD*%
+D16*
+%TO.C,C3*%
+X135942000Y-88392000D03*
+X139192000Y-88392000D03*
+%TD*%
+D18*
+%TO.C,C2*%
+X163169000Y-94996000D03*
+X159919000Y-94996000D03*
+%TD*%
+D17*
+%TO.C,U2*%
+X162495000Y-56515000D03*
+X162495000Y-57785000D03*
+X162495000Y-59055000D03*
+X162495000Y-60325000D03*
+X162495000Y-61595000D03*
+X162495000Y-62865000D03*
+X162495000Y-64135000D03*
+X162495000Y-65405000D03*
+X157545000Y-65405000D03*
+X157545000Y-64135000D03*
+X157545000Y-62865000D03*
+X157545000Y-61595000D03*
+X157545000Y-60325000D03*
+X157545000Y-59055000D03*
+X157545000Y-57785000D03*
+X157545000Y-56515000D03*
+%TD*%
+D19*
+%TO.C,F1*%
+X143510000Y-90935000D03*
+X143510000Y-88135000D03*
+%TD*%
+D20*
+%TO.C,U5*%
+X174177000Y-87234000D03*
+X174177000Y-87884000D03*
+X174177000Y-88534000D03*
+X171517000Y-88534000D03*
+X171517000Y-87234000D03*
+%TD*%
+D21*
+%TO.C,C4*%
+X132080000Y-93827000D03*
+X132080000Y-90577000D03*
+%TD*%
+M02*

gerber/v1.4/bluescsi_iigs_internal-B_Paste.gbp

@@ -0,0 +1,126 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2023-01-26T09:36:58-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Paste,Bot*%
+%TF.FilePolarity,Positive*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2023-01-26 09:36:58*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 Aperture macros list*
+%AMRoundRect*
+0 Rectangle with rounded corners*
+0 $1 Rounding radius*
+0 $2 $3 $4 $5 $6 $7 $8 $9 X,Y pos of 4 corners*
+0 Add a 4 corners polygon primitive as box body*
+4,1,4,$2,$3,$4,$5,$6,$7,$8,$9,$2,$3,0*
+0 Add four circle primitives for the rounded corners*
+1,1,$1+$1,$2,$3*
+1,1,$1+$1,$4,$5*
+1,1,$1+$1,$6,$7*
+1,1,$1+$1,$8,$9*
+0 Add four rect primitives between the rounded corners*
+20,1,$1+$1,$2,$3,$4,$5,0*
+20,1,$1+$1,$4,$5,$6,$7,0*
+20,1,$1+$1,$6,$7,$8,$9,0*
+20,1,$1+$1,$8,$9,$2,$3,0*%
+G04 Aperture macros list end*
+%ADD10R,3.480000X1.846667*%
+%ADD11RoundRect,0.250000X-0.500000X-0.925000X0.500000X-0.925000X0.500000X0.925000X-0.500000X0.925000X0*%
+%ADD12R,1.970000X0.600000*%
+%ADD13RoundRect,0.250000X0.500000X0.925000X-0.500000X0.925000X-0.500000X-0.925000X0.500000X-0.925000X0*%
+%ADD14RoundRect,0.250000X1.075000X-0.375000X1.075000X0.375000X-1.075000X0.375000X-1.075000X-0.375000X0*%
+%ADD15R,1.500000X0.400000*%
+%ADD16RoundRect,0.250000X0.925000X-0.500000X0.925000X0.500000X-0.925000X0.500000X-0.925000X-0.500000X0*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,J6*%
+X127000000Y-50805000D03*
+X127000000Y-53575000D03*
+X127000000Y-56345000D03*
+X127000000Y-59115000D03*
+X127000000Y-61885000D03*
+X127000000Y-64655000D03*
+X127000000Y-67425000D03*
+X127000000Y-70195000D03*
+X127000000Y-72965000D03*
+X127000000Y-75735000D03*
+X127000000Y-78505000D03*
+X127000000Y-81275000D03*
+%TD*%
+D11*
+%TO.C,C1*%
+X160935000Y-52324000D03*
+X164185000Y-52324000D03*
+%TD*%
+D12*
+%TO.C,U3*%
+X162495000Y-81915000D03*
+X162495000Y-83185000D03*
+X162495000Y-84455000D03*
+X162495000Y-85725000D03*
+X162495000Y-86995000D03*
+X162495000Y-88265000D03*
+X162495000Y-89535000D03*
+X162495000Y-90805000D03*
+X157545000Y-90805000D03*
+X157545000Y-89535000D03*
+X157545000Y-88265000D03*
+X157545000Y-86995000D03*
+X157545000Y-85725000D03*
+X157545000Y-84455000D03*
+X157545000Y-83185000D03*
+X157545000Y-81915000D03*
+%TD*%
+D11*
+%TO.C,C3*%
+X135942000Y-88392000D03*
+X139192000Y-88392000D03*
+%TD*%
+D13*
+%TO.C,C2*%
+X163169000Y-94996000D03*
+X159919000Y-94996000D03*
+%TD*%
+D12*
+%TO.C,U2*%
+X162495000Y-56515000D03*
+X162495000Y-57785000D03*
+X162495000Y-59055000D03*
+X162495000Y-60325000D03*
+X162495000Y-61595000D03*
+X162495000Y-62865000D03*
+X162495000Y-64135000D03*
+X162495000Y-65405000D03*
+X157545000Y-65405000D03*
+X157545000Y-64135000D03*
+X157545000Y-62865000D03*
+X157545000Y-61595000D03*
+X157545000Y-60325000D03*
+X157545000Y-59055000D03*
+X157545000Y-57785000D03*
+X157545000Y-56515000D03*
+%TD*%
+D14*
+%TO.C,F1*%
+X143510000Y-90935000D03*
+X143510000Y-88135000D03*
+%TD*%
+D15*
+%TO.C,U5*%
+X174177000Y-87234000D03*
+X174177000Y-87884000D03*
+X174177000Y-88534000D03*
+X171517000Y-88534000D03*
+X171517000Y-87234000D03*
+%TD*%
+D16*
+%TO.C,C4*%
+X132080000Y-93827000D03*
+X132080000Y-90577000D03*
+%TD*%
+M02*

gerber/v1.4/bluescsi_iigs_internal-Edge_Cuts.gm1

@@ -0,0 +1,82 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2023-01-26T09:36:59-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Profile,NP*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2023-01-26 09:36:59*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+%TA.AperFunction,Profile*%
+%ADD10C,0.050000*%
+%TD*%
+G04 APERTURE END LIST*
+D10*
+X186563000Y-79946500D02*
+X186563000Y-92456000D01*
+X125095000Y-101092000D02*
+X125095000Y-48260000D01*
+X181991000Y-56134000D02*
+X185293000Y-56134000D01*
+X180721000Y-94996000D02*
+X180721000Y-101092000D01*
+X186563000Y-57404000D02*
+G75*
+G03*
+X185293000Y-56134000I-1270000J0D01*
+G01*
+X185293000Y-93726000D02*
+G75*
+G03*
+X186563000Y-92456000I0J1270000D01*
+G01*
+X180721000Y-54864000D02*
+G75*
+G03*
+X181991000Y-56134000I1270000J0D01*
+G01*
+X180721000Y-48260000D02*
+X180721000Y-54864000D01*
+X181991000Y-93726000D02*
+G75*
+G03*
+X180721000Y-94996000I0J-1270000D01*
+G01*
+X181991000Y-93726000D02*
+X185293000Y-93726000D01*
+X126365000Y-46990000D02*
+X179451000Y-46990000D01*
+X179451000Y-102362000D02*
+X126365000Y-102362000D01*
+X125095000Y-101092000D02*
+G75*
+G03*
+X126365000Y-102362000I1270000J0D01*
+G01*
+X185420000Y-70764400D02*
+X185420000Y-79565500D01*
+X179451000Y-102362000D02*
+G75*
+G03*
+X180721000Y-101092000I0J1270000D01*
+G01*
+X126365000Y-46990000D02*
+G75*
+G03*
+X125095000Y-48260000I0J-1270000D01*
+G01*
+X186563000Y-57404000D02*
+X186563000Y-70459600D01*
+X185420000Y-70764400D02*
+X186563000Y-70459600D01*
+X180721000Y-48260000D02*
+G75*
+G03*
+X179451000Y-46990000I-1270000J0D01*
+G01*
+X186563000Y-79946500D02*
+X185420000Y-79565500D01*
+M02*

gerber/v1.4/bluescsi_iigs_internal-F_Mask.gts

@@ -0,0 +1,290 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2023-01-26T09:36:58-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Soldermask,Top*%
+%TF.FilePolarity,Negative*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2023-01-26 09:36:58*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 Aperture macros list*
+%AMRoundRect*
+0 Rectangle with rounded corners*
+0 $1 Rounding radius*
+0 $2 $3 $4 $5 $6 $7 $8 $9 X,Y pos of 4 corners*
+0 Add a 4 corners polygon primitive as box body*
+4,1,4,$2,$3,$4,$5,$6,$7,$8,$9,$2,$3,0*
+0 Add four circle primitives for the rounded corners*
+1,1,$1+$1,$2,$3*
+1,1,$1+$1,$4,$5*
+1,1,$1+$1,$6,$7*
+1,1,$1+$1,$8,$9*
+0 Add four rect primitives between the rounded corners*
+20,1,$1+$1,$2,$3,$4,$5,0*
+20,1,$1+$1,$4,$5,$6,$7,0*
+20,1,$1+$1,$6,$7,$8,$9,0*
+20,1,$1+$1,$8,$9,$2,$3,0*%
+G04 Aperture macros list end*
+%ADD10R,1.700000X1.700000*%
+%ADD11C,1.700000*%
+%ADD12R,0.800000X1.000000*%
+%ADD13C,0.900000*%
+%ADD14R,1.500000X0.700000*%
+%ADD15RoundRect,0.249999X0.350001X0.450001X-0.350001X0.450001X-0.350001X-0.450001X0.350001X-0.450001X0*%
+%ADD16RoundRect,0.249999X-0.450001X0.325001X-0.450001X-0.325001X0.450001X-0.325001X0.450001X0.325001X0*%
+%ADD17R,1.000000X1.500000*%
+%ADD18RoundRect,0.249999X-0.350001X-0.450001X0.350001X-0.450001X0.350001X0.450001X-0.350001X0.450001X0*%
+%ADD19O,1.700000X1.700000*%
+%ADD20C,2.100000*%
+%ADD21RoundRect,0.249999X0.450001X-0.325001X0.450001X0.325001X-0.450001X0.325001X-0.450001X-0.325001X0*%
+%ADD22R,1.000000X0.500000*%
+%ADD23R,0.780000X0.720000*%
+%ADD24R,1.080000X1.050000*%
+%ADD25R,1.200000X1.050000*%
+%ADD26R,2.390000X1.050000*%
+%ADD27R,0.550000X2.910000*%
+%ADD28R,3.480000X1.846667*%
+%ADD29R,0.900000X1.200000*%
+%ADD30RoundRect,0.250000X0.450000X0.425000X-0.450000X0.425000X-0.450000X-0.425000X0.450000X-0.425000X0*%
+%ADD31RoundRect,0.150000X-0.825000X-0.150000X0.825000X-0.150000X0.825000X0.150000X-0.825000X0.150000X0*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,U1*%
+X152400000Y-50800000D03*
+D11*
+X152400000Y-53340000D03*
+X152400000Y-55880000D03*
+X152400000Y-58420000D03*
+X152400000Y-60960000D03*
+X152400000Y-63500000D03*
+X152400000Y-66040000D03*
+X152400000Y-68580000D03*
+X152400000Y-71120000D03*
+X152400000Y-73660000D03*
+X152400000Y-76200000D03*
+X152400000Y-78740000D03*
+X152400000Y-81280000D03*
+X152400000Y-83820000D03*
+X152400000Y-86360000D03*
+X152400000Y-88900000D03*
+X152400000Y-91440000D03*
+X152400000Y-93980000D03*
+X152400000Y-96520000D03*
+X152400000Y-99060000D03*
+X167640000Y-99060000D03*
+X167640000Y-96520000D03*
+X167640000Y-93980000D03*
+X167640000Y-91440000D03*
+X167640000Y-88900000D03*
+X167640000Y-86360000D03*
+X167640000Y-83820000D03*
+X167640000Y-81280000D03*
+X167640000Y-78740000D03*
+X167640000Y-76200000D03*
+X167640000Y-73660000D03*
+X167640000Y-71120000D03*
+X167640000Y-68580000D03*
+X167640000Y-66040000D03*
+X167640000Y-63500000D03*
+X167640000Y-60960000D03*
+X167640000Y-58420000D03*
+X167640000Y-55880000D03*
+X167640000Y-53340000D03*
+X167640000Y-50800000D03*
+%TD*%
+D12*
+%TO.C,SW1*%
+X183116000Y-57945000D03*
+D13*
+X184226000Y-63095000D03*
+X184226000Y-60095000D03*
+D12*
+X185326000Y-57945000D03*
+X183116000Y-65245000D03*
+X185326000Y-65245000D03*
+D14*
+X182466000Y-63845000D03*
+X182466000Y-60845000D03*
+X182466000Y-59345000D03*
+%TD*%
+D15*
+%TO.C,R2*%
+X178927000Y-89408000D03*
+X176927000Y-89408000D03*
+%TD*%
+D16*
+%TO.C,D1*%
+X184531000Y-83811000D03*
+X184531000Y-85861000D03*
+%TD*%
+D17*
+%TO.C,JP2*%
+X173833000Y-66548000D03*
+X175133000Y-66548000D03*
+X176433000Y-66548000D03*
+%TD*%
+%TO.C,JP1*%
+X173833000Y-61722000D03*
+X175133000Y-61722000D03*
+X176433000Y-61722000D03*
+%TD*%
+D18*
+%TO.C,R1*%
+X176927000Y-85725000D03*
+X178927000Y-85725000D03*
+%TD*%
+D10*
+%TO.C,J1*%
+X132080000Y-54610000D03*
+D19*
+X134620000Y-54610000D03*
+X132080000Y-57150000D03*
+X134620000Y-57150000D03*
+X132080000Y-59690000D03*
+X134620000Y-59690000D03*
+X132080000Y-62230000D03*
+X134620000Y-62230000D03*
+X132080000Y-64770000D03*
+X134620000Y-64770000D03*
+X132080000Y-67310000D03*
+X134620000Y-67310000D03*
+X132080000Y-69850000D03*
+X134620000Y-69850000D03*
+X132080000Y-72390000D03*
+X134620000Y-72390000D03*
+X132080000Y-74930000D03*
+X134620000Y-74930000D03*
+X132080000Y-77470000D03*
+X134620000Y-77470000D03*
+X132080000Y-80010000D03*
+X134620000Y-80010000D03*
+X132080000Y-82550000D03*
+X134620000Y-82550000D03*
+X132080000Y-85090000D03*
+X134620000Y-85090000D03*
+%TD*%
+D10*
+%TO.C,J2*%
+X142240000Y-54610000D03*
+D19*
+X144780000Y-54610000D03*
+X142240000Y-57150000D03*
+X144780000Y-57150000D03*
+X142240000Y-59690000D03*
+X144780000Y-59690000D03*
+X142240000Y-62230000D03*
+X144780000Y-62230000D03*
+X142240000Y-64770000D03*
+X144780000Y-64770000D03*
+X142240000Y-67310000D03*
+X144780000Y-67310000D03*
+X142240000Y-69850000D03*
+X144780000Y-69850000D03*
+X142240000Y-72390000D03*
+X144780000Y-72390000D03*
+X142240000Y-74930000D03*
+X144780000Y-74930000D03*
+X142240000Y-77470000D03*
+X144780000Y-77470000D03*
+X142240000Y-80010000D03*
+X144780000Y-80010000D03*
+X142240000Y-82550000D03*
+X144780000Y-82550000D03*
+X142240000Y-85090000D03*
+X144780000Y-85090000D03*
+%TD*%
+D10*
+%TO.C,J4*%
+X128905000Y-97536000D03*
+D19*
+X128905000Y-100076000D03*
+%TD*%
+D10*
+%TO.C,J5*%
+X127889000Y-92964000D03*
+D19*
+X127889000Y-90424000D03*
+%TD*%
+D20*
+%TO.C,M1*%
+X177591000Y-95481000D03*
+X177591000Y-100561000D03*
+X172511000Y-95481000D03*
+X172511000Y-100561000D03*
+%TD*%
+%TO.C,M2*%
+X177591000Y-48791000D03*
+X172511000Y-48791000D03*
+X177591000Y-53871000D03*
+X172511000Y-53871000D03*
+%TD*%
+D21*
+%TO.C,D2*%
+X184531000Y-91449000D03*
+X184531000Y-89399000D03*
+%TD*%
+D22*
+%TO.C,J3*%
+X181330000Y-71634000D03*
+X181330000Y-72734000D03*
+X181330000Y-73834000D03*
+X181330000Y-74934000D03*
+X181330000Y-76034000D03*
+X181330000Y-77134000D03*
+X181330000Y-78234000D03*
+X181330000Y-79334000D03*
+D23*
+X178650000Y-69874000D03*
+D24*
+X177380000Y-69859000D03*
+D25*
+X174770000Y-69859000D03*
+X175340000Y-80509000D03*
+D26*
+X178525000Y-80509000D03*
+D27*
+X174095000Y-73198000D03*
+X174095000Y-77388000D03*
+%TD*%
+D28*
+%TO.C,J6*%
+X127000000Y-49420000D03*
+X127000000Y-52190000D03*
+X127000000Y-54960000D03*
+X127000000Y-57730000D03*
+X127000000Y-60500000D03*
+X127000000Y-63270000D03*
+X127000000Y-66040000D03*
+X127000000Y-68810000D03*
+X127000000Y-71580000D03*
+X127000000Y-74350000D03*
+X127000000Y-77120000D03*
+X127000000Y-79890000D03*
+X127000000Y-82660000D03*
+%TD*%
+D29*
+%TO.C,D3*%
+X145922000Y-100330000D03*
+X142622000Y-100330000D03*
+%TD*%
+D30*
+%TO.C,C5*%
+X138256000Y-100330000D03*
+X135556000Y-100330000D03*
+%TD*%
+D31*
+%TO.C,U4*%
+X140781000Y-94107000D03*
+X140781000Y-95377000D03*
+X140781000Y-96647000D03*
+X140781000Y-97917000D03*
+X145731000Y-97917000D03*
+X145731000Y-96647000D03*
+X145731000Y-95377000D03*
+X145731000Y-94107000D03*
+%TD*%
+M02*

gerber/v1.4/bluescsi_iigs_internal-F_Paste.gtp

@@ -0,0 +1,140 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2023-01-26T09:36:58-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Paste,Top*%
+%TF.FilePolarity,Positive*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2023-01-26 09:36:58*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 Aperture macros list*
+%AMRoundRect*
+0 Rectangle with rounded corners*
+0 $1 Rounding radius*
+0 $2 $3 $4 $5 $6 $7 $8 $9 X,Y pos of 4 corners*
+0 Add a 4 corners polygon primitive as box body*
+4,1,4,$2,$3,$4,$5,$6,$7,$8,$9,$2,$3,0*
+0 Add four circle primitives for the rounded corners*
+1,1,$1+$1,$2,$3*
+1,1,$1+$1,$4,$5*
+1,1,$1+$1,$6,$7*
+1,1,$1+$1,$8,$9*
+0 Add four rect primitives between the rounded corners*
+20,1,$1+$1,$2,$3,$4,$5,0*
+20,1,$1+$1,$4,$5,$6,$7,0*
+20,1,$1+$1,$6,$7,$8,$9,0*
+20,1,$1+$1,$8,$9,$2,$3,0*%
+G04 Aperture macros list end*
+%ADD10R,0.800000X1.000000*%
+%ADD11R,1.500000X0.700000*%
+%ADD12RoundRect,0.249999X0.350001X0.450001X-0.350001X0.450001X-0.350001X-0.450001X0.350001X-0.450001X0*%
+%ADD13RoundRect,0.249999X-0.450001X0.325001X-0.450001X-0.325001X0.450001X-0.325001X0.450001X0.325001X0*%
+%ADD14RoundRect,0.249999X-0.350001X-0.450001X0.350001X-0.450001X0.350001X0.450001X-0.350001X0.450001X0*%
+%ADD15RoundRect,0.249999X0.450001X-0.325001X0.450001X0.325001X-0.450001X0.325001X-0.450001X-0.325001X0*%
+%ADD16R,1.000000X0.500000*%
+%ADD17R,0.780000X0.720000*%
+%ADD18R,1.080000X1.050000*%
+%ADD19R,1.200000X1.050000*%
+%ADD20R,2.390000X1.050000*%
+%ADD21R,0.550000X2.910000*%
+%ADD22R,3.480000X1.846667*%
+%ADD23R,0.900000X1.200000*%
+%ADD24RoundRect,0.250000X0.450000X0.425000X-0.450000X0.425000X-0.450000X-0.425000X0.450000X-0.425000X0*%
+%ADD25RoundRect,0.150000X-0.825000X-0.150000X0.825000X-0.150000X0.825000X0.150000X-0.825000X0.150000X0*%
+G04 APERTURE END LIST*
+D10*
+%TO.C,SW1*%
+X183116000Y-57945000D03*
+X185326000Y-57945000D03*
+X183116000Y-65245000D03*
+X185326000Y-65245000D03*
+D11*
+X182466000Y-63845000D03*
+X182466000Y-60845000D03*
+X182466000Y-59345000D03*
+%TD*%
+D12*
+%TO.C,R2*%
+X178927000Y-89408000D03*
+X176927000Y-89408000D03*
+%TD*%
+D13*
+%TO.C,D1*%
+X184531000Y-83811000D03*
+X184531000Y-85861000D03*
+%TD*%
+D14*
+%TO.C,R1*%
+X176927000Y-85725000D03*
+X178927000Y-85725000D03*
+%TD*%
+D15*
+%TO.C,D2*%
+X184531000Y-91449000D03*
+X184531000Y-89399000D03*
+%TD*%
+D16*
+%TO.C,J3*%
+X181330000Y-71634000D03*
+X181330000Y-72734000D03*
+X181330000Y-73834000D03*
+X181330000Y-74934000D03*
+X181330000Y-76034000D03*
+X181330000Y-77134000D03*
+X181330000Y-78234000D03*
+X181330000Y-79334000D03*
+D17*
+X178650000Y-69874000D03*
+D18*
+X177380000Y-69859000D03*
+D19*
+X174770000Y-69859000D03*
+X175340000Y-80509000D03*
+D20*
+X178525000Y-80509000D03*
+D21*
+X174095000Y-73198000D03*
+X174095000Y-77388000D03*
+%TD*%
+D22*
+%TO.C,J6*%
+X127000000Y-49420000D03*
+X127000000Y-52190000D03*
+X127000000Y-54960000D03*
+X127000000Y-57730000D03*
+X127000000Y-60500000D03*
+X127000000Y-63270000D03*
+X127000000Y-66040000D03*
+X127000000Y-68810000D03*
+X127000000Y-71580000D03*
+X127000000Y-74350000D03*
+X127000000Y-77120000D03*
+X127000000Y-79890000D03*
+X127000000Y-82660000D03*
+%TD*%
+D23*
+%TO.C,D3*%
+X145922000Y-100330000D03*
+X142622000Y-100330000D03*
+%TD*%
+D24*
+%TO.C,C5*%
+X138256000Y-100330000D03*
+X135556000Y-100330000D03*
+%TD*%
+D25*
+%TO.C,U4*%
+X140781000Y-94107000D03*
+X140781000Y-95377000D03*
+X140781000Y-96647000D03*
+X140781000Y-97917000D03*
+X145731000Y-97917000D03*
+X145731000Y-96647000D03*
+X145731000Y-95377000D03*
+X145731000Y-94107000D03*
+%TD*%
+M02*

gerber/v1.4/bluescsi_iigs_internal-NPTH-drl_map.gbr

@@ -0,0 +1,610 @@
+%FSLAX45Y45*%
+G04 Gerber Fmt 4.5, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2023-01-26 09:36:56*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+%TA.AperFunction,Profile*%
+%ADD10C,0.050000*%
+%TD*%
+%ADD11C,0.200000*%
+%ADD12C,0.090000*%
+G04 APERTURE END LIST*
+D10*
+X18656300Y-7994650D02*
+X18656300Y-9245600D01*
+X12509500Y-10109200D02*
+X12509500Y-4826000D01*
+X18199100Y-5613400D02*
+X18529300Y-5613400D01*
+X18072100Y-9499600D02*
+X18072100Y-10109200D01*
+X18656300Y-5740400D02*
+G75*
+G03*
+X18529300Y-5613400I-127000J0D01*
+G01*
+X18529300Y-9372600D02*
+G75*
+G03*
+X18656300Y-9245600I0J127000D01*
+G01*
+X18072100Y-5486400D02*
+G75*
+G03*
+X18199100Y-5613400I127000J0D01*
+G01*
+X18072100Y-4826000D02*
+X18072100Y-5486400D01*
+X18199100Y-9372600D02*
+G75*
+G03*
+X18072100Y-9499600I0J-127000D01*
+G01*
+X18199100Y-9372600D02*
+X18529300Y-9372600D01*
+X12636500Y-4699000D02*
+X17945100Y-4699000D01*
+X17945100Y-10236200D02*
+X12636500Y-10236200D01*
+X12509500Y-10109200D02*
+G75*
+G03*
+X12636500Y-10236200I127000J0D01*
+G01*
+X18542000Y-7076440D02*
+X18542000Y-7956550D01*
+X17945100Y-10236200D02*
+G75*
+G03*
+X18072100Y-10109200I0J127000D01*
+G01*
+X12636500Y-4699000D02*
+G75*
+G03*
+X12509500Y-4826000I0J-127000D01*
+G01*
+X18656300Y-5740400D02*
+X18656300Y-7045960D01*
+X18542000Y-7076440D02*
+X18656300Y-7045960D01*
+X18072100Y-4826000D02*
+G75*
+G03*
+X17945100Y-4699000I-127000J0D01*
+G01*
+X18656300Y-7994650D02*
+X18542000Y-7956550D01*
+D11*
+D12*
+X18377600Y-5964500D02*
+X18467600Y-6054500D01*
+X18467600Y-5964500D02*
+X18377600Y-6054500D01*
+X18377600Y-6264500D02*
+X18467600Y-6354500D01*
+X18467600Y-6264500D02*
+X18377600Y-6354500D01*
+D11*
+X12764619Y-10549176D02*
+X12764619Y-10349176D01*
+X12812238Y-10349176D01*
+X12840809Y-10358700D01*
+X12859857Y-10377748D01*
+X12869381Y-10396795D01*
+X12878905Y-10434890D01*
+X12878905Y-10463462D01*
+X12869381Y-10501557D01*
+X12859857Y-10520605D01*
+X12840809Y-10539652D01*
+X12812238Y-10549176D01*
+X12764619Y-10549176D01*
+X12964619Y-10549176D02*
+X12964619Y-10415843D01*
+X12964619Y-10453938D02*
+X12974143Y-10434890D01*
+X12983667Y-10425367D01*
+X13002714Y-10415843D01*
+X13021762Y-10415843D01*
+X13088428Y-10549176D02*
+X13088428Y-10415843D01*
+X13088428Y-10349176D02*
+X13078905Y-10358700D01*
+X13088428Y-10368224D01*
+X13097952Y-10358700D01*
+X13088428Y-10349176D01*
+X13088428Y-10368224D01*
+X13212238Y-10549176D02*
+X13193190Y-10539652D01*
+X13183667Y-10520605D01*
+X13183667Y-10349176D01*
+X13317000Y-10549176D02*
+X13297952Y-10539652D01*
+X13288428Y-10520605D01*
+X13288428Y-10349176D01*
+X13545571Y-10549176D02*
+X13545571Y-10349176D01*
+X13612238Y-10492033D01*
+X13678905Y-10349176D01*
+X13678905Y-10549176D01*
+X13859857Y-10549176D02*
+X13859857Y-10444414D01*
+X13850333Y-10425367D01*
+X13831286Y-10415843D01*
+X13793190Y-10415843D01*
+X13774143Y-10425367D01*
+X13859857Y-10539652D02*
+X13840809Y-10549176D01*
+X13793190Y-10549176D01*
+X13774143Y-10539652D01*
+X13764619Y-10520605D01*
+X13764619Y-10501557D01*
+X13774143Y-10482510D01*
+X13793190Y-10472986D01*
+X13840809Y-10472986D01*
+X13859857Y-10463462D01*
+X13955095Y-10415843D02*
+X13955095Y-10615843D01*
+X13955095Y-10425367D02*
+X13974143Y-10415843D01*
+X14012238Y-10415843D01*
+X14031286Y-10425367D01*
+X14040809Y-10434890D01*
+X14050333Y-10453938D01*
+X14050333Y-10511081D01*
+X14040809Y-10530129D01*
+X14031286Y-10539652D01*
+X14012238Y-10549176D01*
+X13974143Y-10549176D01*
+X13955095Y-10539652D01*
+X14136048Y-10530129D02*
+X14145571Y-10539652D01*
+X14136048Y-10549176D01*
+X14126524Y-10539652D01*
+X14136048Y-10530129D01*
+X14136048Y-10549176D01*
+X14136048Y-10425367D02*
+X14145571Y-10434890D01*
+X14136048Y-10444414D01*
+X14126524Y-10434890D01*
+X14136048Y-10425367D01*
+X14136048Y-10444414D01*
+D12*
+X12417000Y-10833700D02*
+X12507000Y-10923700D01*
+X12507000Y-10833700D02*
+X12417000Y-10923700D01*
+D11*
+X12802714Y-10769176D02*
+X12821762Y-10769176D01*
+X12840809Y-10778700D01*
+X12850333Y-10788224D01*
+X12859857Y-10807271D01*
+X12869381Y-10845367D01*
+X12869381Y-10892986D01*
+X12859857Y-10931081D01*
+X12850333Y-10950129D01*
+X12840809Y-10959652D01*
+X12821762Y-10969176D01*
+X12802714Y-10969176D01*
+X12783667Y-10959652D01*
+X12774143Y-10950129D01*
+X12764619Y-10931081D01*
+X12755095Y-10892986D01*
+X12755095Y-10845367D01*
+X12764619Y-10807271D01*
+X12774143Y-10788224D01*
+X12783667Y-10778700D01*
+X12802714Y-10769176D01*
+X12955095Y-10950129D02*
+X12964619Y-10959652D01*
+X12955095Y-10969176D01*
+X12945571Y-10959652D01*
+X12955095Y-10950129D01*
+X12955095Y-10969176D01*
+X13059857Y-10969176D02*
+X13097952Y-10969176D01*
+X13117000Y-10959652D01*
+X13126524Y-10950129D01*
+X13145571Y-10921557D01*
+X13155095Y-10883462D01*
+X13155095Y-10807271D01*
+X13145571Y-10788224D01*
+X13136048Y-10778700D01*
+X13117000Y-10769176D01*
+X13078905Y-10769176D01*
+X13059857Y-10778700D01*
+X13050333Y-10788224D01*
+X13040809Y-10807271D01*
+X13040809Y-10854890D01*
+X13050333Y-10873938D01*
+X13059857Y-10883462D01*
+X13078905Y-10892986D01*
+X13117000Y-10892986D01*
+X13136048Y-10883462D01*
+X13145571Y-10873938D01*
+X13155095Y-10854890D01*
+X13278905Y-10769176D02*
+X13297952Y-10769176D01*
+X13317000Y-10778700D01*
+X13326524Y-10788224D01*
+X13336048Y-10807271D01*
+X13345571Y-10845367D01*
+X13345571Y-10892986D01*
+X13336048Y-10931081D01*
+X13326524Y-10950129D01*
+X13317000Y-10959652D01*
+X13297952Y-10969176D01*
+X13278905Y-10969176D01*
+X13259857Y-10959652D01*
+X13250333Y-10950129D01*
+X13240809Y-10931081D01*
+X13231286Y-10892986D01*
+X13231286Y-10845367D01*
+X13240809Y-10807271D01*
+X13250333Y-10788224D01*
+X13259857Y-10778700D01*
+X13278905Y-10769176D01*
+X13469381Y-10769176D02*
+X13488428Y-10769176D01*
+X13507476Y-10778700D01*
+X13517000Y-10788224D01*
+X13526524Y-10807271D01*
+X13536048Y-10845367D01*
+X13536048Y-10892986D01*
+X13526524Y-10931081D01*
+X13517000Y-10950129D01*
+X13507476Y-10959652D01*
+X13488428Y-10969176D01*
+X13469381Y-10969176D01*
+X13450333Y-10959652D01*
+X13440809Y-10950129D01*
+X13431286Y-10931081D01*
+X13421762Y-10892986D01*
+X13421762Y-10845367D01*
+X13431286Y-10807271D01*
+X13440809Y-10788224D01*
+X13450333Y-10778700D01*
+X13469381Y-10769176D01*
+X13621762Y-10969176D02*
+X13621762Y-10835843D01*
+X13621762Y-10854890D02*
+X13631286Y-10845367D01*
+X13650333Y-10835843D01*
+X13678905Y-10835843D01*
+X13697952Y-10845367D01*
+X13707476Y-10864414D01*
+X13707476Y-10969176D01*
+X13707476Y-10864414D02*
+X13717000Y-10845367D01*
+X13736048Y-10835843D01*
+X13764619Y-10835843D01*
+X13783667Y-10845367D01*
+X13793190Y-10864414D01*
+X13793190Y-10969176D01*
+X13888428Y-10969176D02*
+X13888428Y-10835843D01*
+X13888428Y-10854890D02*
+X13897952Y-10845367D01*
+X13917000Y-10835843D01*
+X13945571Y-10835843D01*
+X13964619Y-10845367D01*
+X13974143Y-10864414D01*
+X13974143Y-10969176D01*
+X13974143Y-10864414D02*
+X13983667Y-10845367D01*
+X14002714Y-10835843D01*
+X14031286Y-10835843D01*
+X14050333Y-10845367D01*
+X14059857Y-10864414D01*
+X14059857Y-10969176D01*
+X14450333Y-10759652D02*
+X14278905Y-11016795D01*
+X14707476Y-10769176D02*
+X14726524Y-10769176D01*
+X14745571Y-10778700D01*
+X14755095Y-10788224D01*
+X14764619Y-10807271D01*
+X14774143Y-10845367D01*
+X14774143Y-10892986D01*
+X14764619Y-10931081D01*
+X14755095Y-10950129D01*
+X14745571Y-10959652D01*
+X14726524Y-10969176D01*
+X14707476Y-10969176D01*
+X14688428Y-10959652D01*
+X14678905Y-10950129D01*
+X14669381Y-10931081D01*
+X14659857Y-10892986D01*
+X14659857Y-10845367D01*
+X14669381Y-10807271D01*
+X14678905Y-10788224D01*
+X14688428Y-10778700D01*
+X14707476Y-10769176D01*
+X14859857Y-10950129D02*
+X14869381Y-10959652D01*
+X14859857Y-10969176D01*
+X14850333Y-10959652D01*
+X14859857Y-10950129D01*
+X14859857Y-10969176D01*
+X14993190Y-10769176D02*
+X15012238Y-10769176D01*
+X15031286Y-10778700D01*
+X15040809Y-10788224D01*
+X15050333Y-10807271D01*
+X15059857Y-10845367D01*
+X15059857Y-10892986D01*
+X15050333Y-10931081D01*
+X15040809Y-10950129D01*
+X15031286Y-10959652D01*
+X15012238Y-10969176D01*
+X14993190Y-10969176D01*
+X14974143Y-10959652D01*
+X14964619Y-10950129D01*
+X14955095Y-10931081D01*
+X14945571Y-10892986D01*
+X14945571Y-10845367D01*
+X14955095Y-10807271D01*
+X14964619Y-10788224D01*
+X14974143Y-10778700D01*
+X14993190Y-10769176D01*
+X15126524Y-10769176D02*
+X15250333Y-10769176D01*
+X15183667Y-10845367D01*
+X15212238Y-10845367D01*
+X15231286Y-10854890D01*
+X15240809Y-10864414D01*
+X15250333Y-10883462D01*
+X15250333Y-10931081D01*
+X15240809Y-10950129D01*
+X15231286Y-10959652D01*
+X15212238Y-10969176D01*
+X15155095Y-10969176D01*
+X15136048Y-10959652D01*
+X15126524Y-10950129D01*
+X15431286Y-10769176D02*
+X15336048Y-10769176D01*
+X15326524Y-10864414D01*
+X15336048Y-10854890D01*
+X15355095Y-10845367D01*
+X15402714Y-10845367D01*
+X15421762Y-10854890D01*
+X15431286Y-10864414D01*
+X15440809Y-10883462D01*
+X15440809Y-10931081D01*
+X15431286Y-10950129D01*
+X15421762Y-10959652D01*
+X15402714Y-10969176D01*
+X15355095Y-10969176D01*
+X15336048Y-10959652D01*
+X15326524Y-10950129D01*
+X15612238Y-10835843D02*
+X15612238Y-10969176D01*
+X15564619Y-10759652D02*
+X15517000Y-10902510D01*
+X15640809Y-10902510D01*
+X15707476Y-10769176D02*
+X15707476Y-10807271D01*
+X15783667Y-10769176D02*
+X15783667Y-10807271D01*
+X16078905Y-11045367D02*
+X16069381Y-11035843D01*
+X16050333Y-11007271D01*
+X16040809Y-10988224D01*
+X16031286Y-10959652D01*
+X16021762Y-10912033D01*
+X16021762Y-10873938D01*
+X16031286Y-10826319D01*
+X16040809Y-10797748D01*
+X16050333Y-10778700D01*
+X16069381Y-10750129D01*
+X16078905Y-10740605D01*
+X16145571Y-10788224D02*
+X16155095Y-10778700D01*
+X16174143Y-10769176D01*
+X16221762Y-10769176D01*
+X16240809Y-10778700D01*
+X16250333Y-10788224D01*
+X16259857Y-10807271D01*
+X16259857Y-10826319D01*
+X16250333Y-10854890D01*
+X16136048Y-10969176D01*
+X16259857Y-10969176D01*
+X16497952Y-10969176D02*
+X16497952Y-10769176D01*
+X16583667Y-10969176D02*
+X16583667Y-10864414D01*
+X16574143Y-10845367D01*
+X16555095Y-10835843D01*
+X16526524Y-10835843D01*
+X16507476Y-10845367D01*
+X16497952Y-10854890D01*
+X16707476Y-10969176D02*
+X16688428Y-10959652D01*
+X16678905Y-10950129D01*
+X16669381Y-10931081D01*
+X16669381Y-10873938D01*
+X16678905Y-10854890D01*
+X16688428Y-10845367D01*
+X16707476Y-10835843D01*
+X16736048Y-10835843D01*
+X16755095Y-10845367D01*
+X16764619Y-10854890D01*
+X16774143Y-10873938D01*
+X16774143Y-10931081D01*
+X16764619Y-10950129D01*
+X16755095Y-10959652D01*
+X16736048Y-10969176D01*
+X16707476Y-10969176D01*
+X16888429Y-10969176D02*
+X16869381Y-10959652D01*
+X16859857Y-10940605D01*
+X16859857Y-10769176D01*
+X17040810Y-10959652D02*
+X17021762Y-10969176D01*
+X16983667Y-10969176D01*
+X16964619Y-10959652D01*
+X16955095Y-10940605D01*
+X16955095Y-10864414D01*
+X16964619Y-10845367D01*
+X16983667Y-10835843D01*
+X17021762Y-10835843D01*
+X17040810Y-10845367D01*
+X17050333Y-10864414D01*
+X17050333Y-10883462D01*
+X16955095Y-10902510D01*
+X17126524Y-10959652D02*
+X17145571Y-10969176D01*
+X17183667Y-10969176D01*
+X17202714Y-10959652D01*
+X17212238Y-10940605D01*
+X17212238Y-10931081D01*
+X17202714Y-10912033D01*
+X17183667Y-10902510D01*
+X17155095Y-10902510D01*
+X17136048Y-10892986D01*
+X17126524Y-10873938D01*
+X17126524Y-10864414D01*
+X17136048Y-10845367D01*
+X17155095Y-10835843D01*
+X17183667Y-10835843D01*
+X17202714Y-10845367D01*
+X17278905Y-11045367D02*
+X17288429Y-11035843D01*
+X17307476Y-11007271D01*
+X17317000Y-10988224D01*
+X17326524Y-10959652D01*
+X17336048Y-10912033D01*
+X17336048Y-10873938D01*
+X17326524Y-10826319D01*
+X17317000Y-10797748D01*
+X17307476Y-10778700D01*
+X17288429Y-10750129D01*
+X17278905Y-10740605D01*
+X17640810Y-11045367D02*
+X17631286Y-11035843D01*
+X17612238Y-11007271D01*
+X17602714Y-10988224D01*
+X17593190Y-10959652D01*
+X17583667Y-10912033D01*
+X17583667Y-10873938D01*
+X17593190Y-10826319D01*
+X17602714Y-10797748D01*
+X17612238Y-10778700D01*
+X17631286Y-10750129D01*
+X17640810Y-10740605D01*
+X17717000Y-10835843D02*
+X17717000Y-10969176D01*
+X17717000Y-10854890D02*
+X17726524Y-10845367D01*
+X17745571Y-10835843D01*
+X17774143Y-10835843D01*
+X17793190Y-10845367D01*
+X17802714Y-10864414D01*
+X17802714Y-10969176D01*
+X17926524Y-10969176D02*
+X17907476Y-10959652D01*
+X17897952Y-10950129D01*
+X17888429Y-10931081D01*
+X17888429Y-10873938D01*
+X17897952Y-10854890D01*
+X17907476Y-10845367D01*
+X17926524Y-10835843D01*
+X17955095Y-10835843D01*
+X17974143Y-10845367D01*
+X17983667Y-10854890D01*
+X17993190Y-10873938D01*
+X17993190Y-10931081D01*
+X17983667Y-10950129D01*
+X17974143Y-10959652D01*
+X17955095Y-10969176D01*
+X17926524Y-10969176D01*
+X18050333Y-10835843D02*
+X18126524Y-10835843D01*
+X18078905Y-10769176D02*
+X18078905Y-10940605D01*
+X18088429Y-10959652D01*
+X18107476Y-10969176D01*
+X18126524Y-10969176D01*
+X18345571Y-10835843D02*
+X18345571Y-11035843D01*
+X18345571Y-10845367D02*
+X18364619Y-10835843D01*
+X18402714Y-10835843D01*
+X18421762Y-10845367D01*
+X18431286Y-10854890D01*
+X18440810Y-10873938D01*
+X18440810Y-10931081D01*
+X18431286Y-10950129D01*
+X18421762Y-10959652D01*
+X18402714Y-10969176D01*
+X18364619Y-10969176D01*
+X18345571Y-10959652D01*
+X18555095Y-10969176D02*
+X18536048Y-10959652D01*
+X18526524Y-10940605D01*
+X18526524Y-10769176D01*
+X18717000Y-10969176D02*
+X18717000Y-10864414D01*
+X18707476Y-10845367D01*
+X18688429Y-10835843D01*
+X18650333Y-10835843D01*
+X18631286Y-10845367D01*
+X18717000Y-10959652D02*
+X18697952Y-10969176D01*
+X18650333Y-10969176D01*
+X18631286Y-10959652D01*
+X18621762Y-10940605D01*
+X18621762Y-10921557D01*
+X18631286Y-10902510D01*
+X18650333Y-10892986D01*
+X18697952Y-10892986D01*
+X18717000Y-10883462D01*
+X18783667Y-10835843D02*
+X18859857Y-10835843D01*
+X18812238Y-10769176D02*
+X18812238Y-10940605D01*
+X18821762Y-10959652D01*
+X18840810Y-10969176D01*
+X18859857Y-10969176D01*
+X19002714Y-10959652D02*
+X18983667Y-10969176D01*
+X18945571Y-10969176D01*
+X18926524Y-10959652D01*
+X18917000Y-10940605D01*
+X18917000Y-10864414D01*
+X18926524Y-10845367D01*
+X18945571Y-10835843D01*
+X18983667Y-10835843D01*
+X19002714Y-10845367D01*
+X19012238Y-10864414D01*
+X19012238Y-10883462D01*
+X18917000Y-10902510D01*
+X19183667Y-10969176D02*
+X19183667Y-10769176D01*
+X19183667Y-10959652D02*
+X19164619Y-10969176D01*
+X19126524Y-10969176D01*
+X19107476Y-10959652D01*
+X19097952Y-10950129D01*
+X19088429Y-10931081D01*
+X19088429Y-10873938D01*
+X19097952Y-10854890D01*
+X19107476Y-10845367D01*
+X19126524Y-10835843D01*
+X19164619Y-10835843D01*
+X19183667Y-10845367D01*
+X19259857Y-11045367D02*
+X19269381Y-11035843D01*
+X19288429Y-11007271D01*
+X19297952Y-10988224D01*
+X19307476Y-10959652D01*
+X19317000Y-10912033D01*
+X19317000Y-10873938D01*
+X19307476Y-10826319D01*
+X19297952Y-10797748D01*
+X19288429Y-10778700D01*
+X19269381Y-10750129D01*
+X19259857Y-10740605D01*
+M02*

gerber/v1.4/bluescsi_iigs_internal-NPTH.drl

@@ -0,0 +1,18 @@
+M48
+; DRILL file {KiCad (6.0.4-0)} date Thursday, January 26, 2023 at 09:36:55 AM
+; FORMAT={-:-/ absolute / metric / decimal}
+; #@! TF.CreationDate,2023-01-26T09:36:55-07:00
+; #@! TF.GenerationSoftware,Kicad,Pcbnew,(6.0.4-0)
+; #@! TF.FileFunction,NonPlated,1,2,NPTH
+FMAT,2
+METRIC
+; #@! TA.AperFunction,NonPlated,NPTH,ComponentDrill
+T1C0.900
+%
+G90
+G05
+T1
+X184.226Y-60.095
+X184.226Y-63.095
+T0
+M30

gerber/v1.4/bluescsi_iigs_internal-PTH.drl

@@ -0,0 +1,150 @@
+M48
+; DRILL file {KiCad (6.0.4-0)} date Thursday, January 26, 2023 at 09:36:55 AM
+; FORMAT={-:-/ absolute / metric / decimal}
+; #@! TF.CreationDate,2023-01-26T09:36:55-07:00
+; #@! TF.GenerationSoftware,Kicad,Pcbnew,(6.0.4-0)
+; #@! TF.FileFunction,Plated,1,2,PTH
+FMAT,2
+METRIC
+; #@! TA.AperFunction,Plated,PTH,ViaDrill
+T1C0.400
+; #@! TA.AperFunction,Plated,PTH,ComponentDrill
+T2C1.000
+; #@! TA.AperFunction,Plated,PTH,ComponentDrill
+T3C1.700
+%
+G90
+G05
+T1
+X138.938Y-94.234
+X139.065Y-51.435
+X144.018Y-97.79
+X146.812Y-66.802
+X147.066Y-93.472
+X147.828Y-52.324
+X148.717Y-69.85
+X155.575Y-60.96
+X155.702Y-86.36
+X156.845Y-52.705
+X159.004Y-91.948
+X159.025Y-62.234
+X160.909Y-64.135
+X163.068Y-67.056
+X164.338Y-60.96
+X164.338Y-86.36
+X169.799Y-64.77
+X170.307Y-85.979
+X170.688Y-58.928
+X170.815Y-66.675
+X170.815Y-61.722
+X171.45Y-83.947
+X172.72Y-83.82
+X179.07Y-74.676
+T2
+X127.889Y-90.424
+X127.889Y-92.964
+X128.905Y-97.536
+X128.905Y-100.076
+X132.08Y-54.61
+X132.08Y-57.15
+X132.08Y-59.69
+X132.08Y-62.23
+X132.08Y-64.77
+X132.08Y-67.31
+X132.08Y-69.85
+X132.08Y-72.39
+X132.08Y-74.93
+X132.08Y-77.47
+X132.08Y-80.01
+X132.08Y-82.55
+X132.08Y-85.09
+X134.62Y-54.61
+X134.62Y-57.15
+X134.62Y-59.69
+X134.62Y-62.23
+X134.62Y-64.77
+X134.62Y-67.31
+X134.62Y-69.85
+X134.62Y-72.39
+X134.62Y-74.93
+X134.62Y-77.47
+X134.62Y-80.01
+X134.62Y-82.55
+X134.62Y-85.09
+X142.24Y-54.61
+X142.24Y-57.15
+X142.24Y-59.69
+X142.24Y-62.23
+X142.24Y-64.77
+X142.24Y-67.31
+X142.24Y-69.85
+X142.24Y-72.39
+X142.24Y-74.93
+X142.24Y-77.47
+X142.24Y-80.01
+X142.24Y-82.55
+X142.24Y-85.09
+X144.78Y-54.61
+X144.78Y-57.15
+X144.78Y-59.69
+X144.78Y-62.23
+X144.78Y-64.77
+X144.78Y-67.31
+X144.78Y-69.85
+X144.78Y-72.39
+X144.78Y-74.93
+X144.78Y-77.47
+X144.78Y-80.01
+X144.78Y-82.55
+X144.78Y-85.09
+X152.4Y-50.8
+X152.4Y-53.34
+X152.4Y-55.88
+X152.4Y-58.42
+X152.4Y-60.96
+X152.4Y-63.5
+X152.4Y-66.04
+X152.4Y-68.58
+X152.4Y-71.12
+X152.4Y-73.66
+X152.4Y-76.2
+X152.4Y-78.74
+X152.4Y-81.28
+X152.4Y-83.82
+X152.4Y-86.36
+X152.4Y-88.9
+X152.4Y-91.44
+X152.4Y-93.98
+X152.4Y-96.52
+X152.4Y-99.06
+X167.64Y-50.8
+X167.64Y-53.34
+X167.64Y-55.88
+X167.64Y-58.42
+X167.64Y-60.96
+X167.64Y-63.5
+X167.64Y-66.04
+X167.64Y-68.58
+X167.64Y-71.12
+X167.64Y-73.66
+X167.64Y-76.2
+X167.64Y-78.74
+X167.64Y-81.28
+X167.64Y-83.82
+X167.64Y-86.36
+X167.64Y-88.9
+X167.64Y-91.44
+X167.64Y-93.98
+X167.64Y-96.52
+X167.64Y-99.06
+T3
+X172.511Y-48.791
+X172.511Y-53.871
+X172.511Y-95.481
+X172.511Y-100.561
+X177.591Y-48.791
+X177.591Y-53.871
+X177.591Y-95.481
+X177.591Y-100.561
+T0
+M30

gerber/v1.4/bluescsi_iigs_internal-User_Eco1.gbr

@@ -0,0 +1,14 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2023-01-26T09:36:58-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Other,ECO1*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2023-01-26 09:36:58*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 APERTURE END LIST*
+M02*

gerber/v1.4/bluescsi_iigs_internal-User_Eco2.gbr

@@ -0,0 +1,14 @@
+%TF.GenerationSoftware,KiCad,Pcbnew,(6.0.4-0)*%
+%TF.CreationDate,2023-01-26T09:36:59-07:00*%
+%TF.ProjectId,bluescsi_iigs_internal,626c7565-7363-4736-995f-696967735f69,rev?*%
+%TF.SameCoordinates,Original*%
+%TF.FileFunction,Other,ECO2*%
+%FSLAX46Y46*%
+G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
+G04 Created by KiCad (PCBNEW (6.0.4-0)) date 2023-01-26 09:36:59*
+%MOMM*%
+%LPD*%
+G01*
+G04 APERTURE LIST*
+G04 APERTURE END LIST*
+M02*

installation/README.md

@@ -0,0 +1,120 @@
+# BlueGS Installation Guide
+
+<!-- TOC -->
+
+- [BlueGS Installation Guide](#bluegs-installation-guide)
+- [Introduction](#introduction)
+- [Steps](#steps)
+- [Open computer case](#open-computer-case)
+- [Remove rear slot cover](#remove-rear-slot-cover)
+- [Unscrew DB-25 Connector](#unscrew-db-25-connector)
+- [Remove SCSI card](#remove-scsi-card)
+- [Move DB-25 connector](#move-db-25-connector)
+- [Attach ribbon cable](#attach-ribbon-cable)
+- [Install BlueGS in rear slot](#install-bluegs-in-rear-slot)
+- [Reinstall DB-25 connector in rear slot](#reinstall-db-25-connector-in-rear-slot)
+- [Reinstall SCSI card and close computer case](#reinstall-scsi-card-and-close-computer-case)
+- [Insert MicroSD card, check termination](#insert-microsd-card-check-termination)
+- [Power on and enjoy!](#power-on-and-enjoy)
+
+<!-- /TOC -->
+# Introduction
+
+Before continuing, please ensure you have all the required parts ready:
+
+* Assembled BlueGS board, including "Blue Pill" module (See [assembly guide](../assembly/) for more info)
+* Rear slot cover
+* 2x screws for rear slot cover ("US Machine Screw" size: #4-40, length: > 0.75in/15mm)
+* 26-pin ribbon cable
+
+# Open computer case
+
+Turn off the computer power switch and unplug the power connector.
+
+Open the top cover of the computer case.
+
+![Opening IIgs cover](images/opening_iigs.jpg)
+
+Before continuing, it is recommended that your remove any static electricity from you body by "grounding" yourself. To do this, touch the metal part of any electrical appliance that uses a grounded/earthed electrical plug (the outside of a metal surge protector, for example).
+
+# Remove rear slot cover
+
+Find an unused DB-25 slot cover. The DB-25 slots are the longest, and a usable slot will be the same length as the slot already used for the external connector of your SCSI card.
+
+To remove the cover, grasp the metal tab on the inside of the slot and turn counter-clockwise for 1/4 of a turn. Remove the metal tab, and the plastic slot cover should fall away.
+
+Keep both the metal tab and the plastic cover for later re-use as these parts are very hard to replace.
+
+![IIgs slot cover tabs](images/slot_cover_tab_iigs.jpg)
+![IIgs slot cover tab removal](images/slot_cover_tab_turn_iigs.jpg)
+
+# Unscrew DB-25 Connector
+
+Find the existing connector for the SCSI card on the rear of the computer. It may look similar to connector for a serial card, so make sure you find the correct connector. Using a small socket or needle-nose pliers, loosen the two screw mounts on either end of the connector and remove them. The DB-25 connector should now be freed.
+
+![IIgs DB-25 Connector Removal](images/unscrew_db25_iigs.jpg)
+
+# Remove SCSI card
+
+Find your SCSI card (typically in slot #7) and remove it by pulling it firmly upward.
+
+IMPORTANT: While removing the card, ensure the cable for the DB-25 connector (see previous step) is kept away from the metal tabs on the rear of the computer case. These tabs can be **sharp** and can damage the cable.
+
+![IIgs SCSI Card Removal](images/remove_scsi_card_iigs.jpg)
+# Move DB-25 connector
+
+With the SCSI card out of the machine, look at the long rectangular connection where the DB-25 cable connects to the SCSI card (known as an "IDC connector"). Note where "Pin 1" is oriented. Pin 1 is usually marked by a red stripe.
+
+Next, remove the DB-25 connector from the SCSI card. Do this by grasping the IDC connector on the SCSI card and gently pulling away from the board.
+
+Next, take the IDC connector on the DB-25 cable and connect it the BlueGS board. It can connect to *either* connector J1 or J2.
+
+When connecting the cable, make sure that **Pin 1** is correctly aligned. On the cable, Pin 1 is usually marked by a red stripe. On BlueGS, Pin 1 for connectors J1 and J2 are those closest to the top-left corner and the pins are marked with a "1" on the board next to them.
+
+IMPORTANT: Again, *make sure* pin 1 is correctly aligned.
+
+![DB-25 connected to BlueGS](images/db25_connected_to_bluegs.jpg)
+
+# Attach ribbon cable
+
+Take the included ribbon cable and attach one end to BlueGS. Use either J1 or J2, whichever connector is not used by the DB-25 connector in the previous step. As before, ensure that Pin 1 is correctly aligned.
+
+Then, connect the other end of the ribbon cable to the SCSI card. Plug it in so that Pin 1 of the ribbon cable is in the same place where Pin 1 of the DB-25 cable was previously.
+
+![DB-25 and ribbon cable connected to BlueGS](images/both_cables_connected_to_bluegs.jpg)
+
+# Install BlueGS in rear slot
+
+Place BlueGS so the edge with the MicroSD slot, LEDs, and switch is inside one of the open slots on the rear of the computer. It is recommended to orient BlueGS so that the USB port is pointed upwards.
+
+Place the included slot cover on the *outside* of the case over the appropriate slot and thread the included screws through the two screw holes and in to the brackets on BlueGS.
+
+Once the screws are correctly threaded, gently tighten them down with a screwdriver until BlueGS is firmly attached to the slot.
+
+![BlueGS in IIgs rear slot](images/bluegs_slot_cover_installation_iigs.jpg)
+
+# Reinstall DB-25 connector in rear slot
+
+In the remaining open slot, reinstall the DB-25 connector.
+
+![Reinstall DB-25 connector in IIgs rear slot](images/reinstall_db25_iigs.jpg)
+
+# Reinstall SCSI card and close computer case
+
+Reinstall the SCSI card in the correct slot and replace the cover on the computer.
+
+![Closing IIgs case](images/closing_iigs.jpg)
+
+# Insert MicroSD card, check termination
+
+Take a MicroSD card that has been previously prepared (instruction [here](https://github.com/erichelgeson/BlueSCSI/wiki/Usage)) and insert it in to the slot on the rear.
+
+If you have no other SCSI devices connected to your computer, the "Termination" switch should be set to "On".
+
+# Power on and enjoy!
+
+Reconnect all necessary cables, turn on the power and enjoy.
+
+The "Power" LED should light the moment the computer turns on, and the "ACT" LED should light whenever the emulated SCSI drive is being read or written.
+
+![Show Power and Activity LEDs on BlueGS installed in IIgs](images/bluegs_lights_iigs.jpg)

kicad/bluescsi_iigs_internal-cache.lib

@@ -55,6 +55,125 @@ X Pin_2 2 200 -100 150 L 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
+# Connector_Conn_01x05_Male
+#
+DEF Connector_Conn_01x05_Male J 0 40 Y N 1 F N
+F0 "J" 0 300 50 H V C CNN
+F1 "Connector_Conn_01x05_Male" 0 -300 50 H V C CNN
+F2 "" 0 0 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+$FPLIST
+ Connector*:*_1x??_*
+$ENDFPLIST
+DRAW
+S 34 -195 0 -205 1 1 6 F
+S 34 -95 0 -105 1 1 6 F
+S 34 5 0 -5 1 1 6 F
+S 34 105 0 95 1 1 6 F
+S 34 205 0 195 1 1 6 F
+P 2 1 1 6 50 -200 34 -200 N
+P 2 1 1 6 50 -100 34 -100 N
+P 2 1 1 6 50 0 34 0 N
+P 2 1 1 6 50 100 34 100 N
+P 2 1 1 6 50 200 34 200 N
+X Pin_1 1 200 200 150 L 50 50 1 1 P
+X Pin_2 2 200 100 150 L 50 50 1 1 P
+X Pin_3 3 200 0 150 L 50 50 1 1 P
+X Pin_4 4 200 -100 150 L 50 50 1 1 P
+X Pin_5 5 200 -200 150 L 50 50 1 1 P
+ENDDRAW
+ENDDEF
+#
+# Connector_DB25_Male
+#
+DEF Connector_DB25_Male J 0 40 Y N 1 F N
+F0 "J" 0 1350 50 H V C CNN
+F1 "Connector_DB25_Male" 0 -1375 50 H V C CNN
+F2 "" 0 0 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+$FPLIST
+ DSUB*Male*
+$ENDFPLIST
+DRAW
+C -70 -1200 30 0 1 0 F
+C -70 -1000 30 0 1 0 F
+C -70 -800 30 0 1 0 F
+C -70 -600 30 0 1 0 F
+C -70 -400 30 0 1 0 F
+C -70 -200 30 0 1 0 F
+C -70 0 30 0 1 0 F
+C -70 200 30 0 1 0 F
+C -70 400 30 0 1 0 F
+C -70 600 30 0 1 0 F
+C -70 800 30 0 1 0 F
+C -70 1000 30 0 1 0 F
+C -70 1200 30 0 1 0 F
+C 50 -1100 30 0 1 0 F
+C 50 -900 30 0 1 0 F
+C 50 -700 30 0 1 0 F
+C 50 -500 30 0 1 0 F
+C 50 -300 30 0 1 0 F
+C 50 -100 30 0 1 0 F
+C 50 100 30 0 1 0 F
+C 50 300 30 0 1 0 F
+C 50 500 30 0 1 0 F
+C 50 700 30 0 1 0 F
+C 50 900 30 0 1 0 F
+C 50 1100 30 0 1 0 F
+P 2 0 1 0 -150 -1200 -100 -1200 N
+P 2 0 1 0 -150 -1100 20 -1100 N
+P 2 0 1 0 -150 -1000 -100 -1000 N
+P 2 0 1 0 -150 -900 20 -900 N
+P 2 0 1 0 -150 -800 -100 -800 N
+P 2 0 1 0 -150 -700 20 -700 N
+P 2 0 1 0 -150 -600 -100 -600 N
+P 2 0 1 0 -150 -500 20 -500 N
+P 2 0 1 0 -150 -400 -100 -400 N
+P 2 0 1 0 -150 -300 20 -300 N
+P 2 0 1 0 -150 -200 -100 -200 N
+P 2 0 1 0 -150 -100 20 -100 N
+P 2 0 1 0 -150 0 -100 0 N
+P 2 0 1 0 -150 100 20 100 N
+P 2 0 1 0 -150 200 -100 200 N
+P 2 0 1 0 -150 300 20 300 N
+P 2 0 1 0 -150 400 -100 400 N
+P 2 0 1 0 -150 500 20 500 N
+P 2 0 1 0 -150 600 -100 600 N
+P 2 0 1 0 -150 700 20 700 N
+P 2 0 1 0 -150 800 -100 800 N
+P 2 0 1 0 -150 900 20 900 N
+P 2 0 1 0 -150 1000 -100 1000 N
+P 2 0 1 0 -150 1100 20 1100 N
+P 2 0 1 0 -150 1200 -100 1200 N
+P 5 0 1 10 -150 -1325 150 -1175 150 1175 -150 1325 -150 -1325 f
+X 1 1 -300 -1200 150 R 50 50 1 1 P
+X 10 10 -300 600 150 R 50 50 1 1 P
+X 11 11 -300 800 150 R 50 50 1 1 P
+X 12 12 -300 1000 150 R 50 50 1 1 P
+X 13 13 -300 1200 150 R 50 50 1 1 P
+X P14 14 -300 -1100 150 R 50 50 1 1 P
+X P15 15 -300 -900 150 R 50 50 1 1 P
+X P16 16 -300 -700 150 R 50 50 1 1 P
+X P17 17 -300 -500 150 R 50 50 1 1 P
+X P18 18 -300 -300 150 R 50 50 1 1 P
+X P19 19 -300 -100 150 R 50 50 1 1 P
+X 2 2 -300 -1000 150 R 50 50 1 1 P
+X P20 20 -300 100 150 R 50 50 1 1 P
+X P21 21 -300 300 150 R 50 50 1 1 P
+X P22 22 -300 500 150 R 50 50 1 1 P
+X P23 23 -300 700 150 R 50 50 1 1 P
+X P24 24 -300 900 150 R 50 50 1 1 P
+X P25 25 -300 1100 150 R 50 50 1 1 P
+X 3 3 -300 -800 150 R 50 50 1 1 P
+X 4 4 -300 -600 150 R 50 50 1 1 P
+X 5 5 -300 -400 150 R 50 50 1 1 P
+X 6 6 -300 -200 150 R 50 50 1 1 P
+X 7 7 -300 0 150 R 50 50 1 1 P
+X 8 8 -300 200 150 R 50 50 1 1 P
+X 9 9 -300 400 150 R 50 50 1 1 P
+ENDDRAW
+ENDDEF
+#
 # Connector_Generic_Conn_02x08_Counter_Clockwise
 #
 DEF Connector_Generic_Conn_02x08_Counter_Clockwise J 0 40 Y N 1 F N
@@ -169,6 +288,25 @@ X Pin_9 9 -200 200 150 R 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
+# Connector_Screw_Terminal_01x01
+#
+DEF Connector_Screw_Terminal_01x01 J 0 40 Y N 1 F N
+F0 "J" 0 100 50 H V C CNN
+F1 "Connector_Screw_Terminal_01x01" 0 -100 50 H V C CNN
+F2 "" 0 0 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+$FPLIST
+ TerminalBlock*:*
+$ENDFPLIST
+DRAW
+C 0 0 25 1 1 6 N
+S -50 50 50 -50 1 1 10 f
+P 2 1 1 6 -21 13 13 -20 N
+P 2 1 1 6 -14 20 20 -13 N
+X Pin_1 1 -200 0 150 R 50 50 1 1 P
+ENDDRAW
+ENDDEF
+#
 # Device_C
 #
 DEF Device_C C 0 10 N Y 1 F N
@@ -207,25 +345,21 @@ X ~ 2 0 -150 110 U 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
-# Device_D_Schottky
+# Device_Fuse
 #
-DEF Device_D_Schottky D 0 40 N N 1 F N
-F0 "D" 0 100 50 H V C CNN
-F1 "Device_D_Schottky" 0 -100 50 H V C CNN
-F2 "" 0 0 50 H I C CNN
+DEF Device_Fuse F 0 0 N Y 1 F N
+F0 "F" 80 0 50 V V C CNN
+F1 "Device_Fuse" -75 0 50 V V C CNN
+F2 "" -70 0 50 V I C CNN
 F3 "" 0 0 50 H I C CNN
 $FPLIST
- TO-???*
- *_Diode_*
- *SingleDiode*
- D_*
+ *Fuse*
 $ENDFPLIST
 DRAW
-P 2 0 1 0 50 0 -50 0 N
-P 4 0 1 10 50 50 50 -50 -50 0 50 50 N
-P 6 0 1 10 -75 25 -75 50 -50 50 -50 -50 -25 -50 -25 -25 N
-X K 1 -150 0 100 R 50 50 1 1 P
-X A 2 150 0 100 L 50 50 1 1 P
+S -30 -100 30 100 0 1 10 N
+P 2 0 1 0 0 100 0 -100 N
+X ~ 1 0 150 50 D 50 50 1 1 P
+X ~ 2 0 -150 50 U 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
@@ -269,6 +403,26 @@ X ~ 2 0 -150 50 U 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
+# Diode_1N4001
+#
+DEF Diode_1N4001 D 0 40 N N 1 F N
+F0 "D" 0 100 50 H V C CNN
+F1 "Diode_1N4001" 0 -100 50 H V C CNN
+F2 "Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal" 0 -175 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+ALIAS 1N4002 1N4003 1N4004 1N4005 1N4006 1N4007 BA157 BA158 BA159
+$FPLIST
+ D*DO?41*
+$ENDFPLIST
+DRAW
+P 2 0 1 10 -50 50 -50 -50 N
+P 2 0 1 0 50 0 -50 0 N
+P 4 0 1 10 50 50 50 -50 -50 0 50 50 N
+X K 1 -150 0 100 R 50 50 1 1 P
+X A 2 150 0 100 L 50 50 1 1 P
+ENDDRAW
+ENDDEF
+#
 # Jumper_Jumper_3_Open
 #
 DEF Jumper_Jumper_3_Open JP 0 0 Y N 1 F N
@@ -418,37 +572,24 @@ X PA12 9 -800 0 200 R 50 50 1 1 B
 ENDDRAW
 ENDDEF
 #
-# Mechanical_MountingHole
+# Regulator_Linear_L7805
 #
-DEF Mechanical_MountingHole H 0 40 Y Y 1 F N
-F0 "H" 0 200 50 H V C CNN
-F1 "Mechanical_MountingHole" 0 125 50 H V C CNN
-F2 "" 0 0 50 H I C CNN
-F3 "" 0 0 50 H I C CNN
-$FPLIST
- MountingHole*
-$ENDFPLIST
-DRAW
-C 0 0 50 0 1 50 N
-ENDDRAW
-ENDDEF
-#
-# Regulator_Linear_AMS1117-5.0
-#
-DEF Regulator_Linear_AMS1117-5.0 U 0 10 Y Y 1 F N
+DEF Regulator_Linear_L7805 U 0 10 Y Y 1 F N
 F0 "U" -150 125 50 H V C CNN
-F1 "Regulator_Linear_AMS1117-5.0" 0 125 50 H V L CNN
-F2 "Package_TO_SOT_SMD:SOT-223-3_TabPin2" 0 200 50 H I C CNN
-F3 "" 100 -250 50 H I C CNN
-ALIAS AP1117-18 AP1117-25 AP1117-33 AP1117-50 LD1117S33TR_SOT223 LD1117S12TR_SOT223 LD1117S18TR_SOT223 LD1117S25TR_SOT223 LD1117S50TR_SOT223 NCP1117-12_SOT223 NCP1117-1.5_SOT223 NCP1117-1.8_SOT223 NCP1117-2.0_SOT223 NCP1117-2.5_SOT223 NCP1117-2.85_SOT223 NCP1117-3.3_SOT223 NCP1117-5.0_SOT223 AMS1117-1.5 AMS1117-1.8 AMS1117-2.5 AMS1117-2.85 AMS1117-3.3 AMS1117-5.0
+F1 "Regulator_Linear_L7805" 0 125 50 H V L CNN
+F2 "" 25 -150 50 H I L CIN
+F3 "" 0 -50 50 H I C CNN
+ALIAS L7806 L7808 L7885 L7809 L7812 L7815 L7818 L7824
 $FPLIST
- SOT?223*TabPin2*
+ TO?252*
+ TO?263*
+ TO?220*
 $ENDFPLIST
 DRAW
-S -200 -200 200 75 0 1 10 f
-X GND 1 0 -300 100 U 50 50 1 1 W
-X VO 2 300 0 100 L 50 50 1 1 w
-X VI 3 -300 0 100 R 50 50 1 1 W
+S -200 75 200 -200 0 1 10 f
+X IN 1 -300 0 100 R 50 50 1 1 W
+X GND 2 0 -300 100 U 50 50 1 1 W
+X OUT 3 300 0 100 L 50 50 1 1 w
 ENDDRAW
 ENDDEF
 #

kicad/bluescsi_iigs_internal-rescue.dcm

@@ -0,0 +1,3 @@
+EESchema-DOCLIB  Version 2.0
+#
+#End Doc Library

kicad/bluescsi_iigs_internal-rescue.lib

@@ -0,0 +1,173 @@
+EESchema-LIBRARY Version 2.4
+#encoding utf-8
+#
+# CP-Device
+#
+DEF CP-Device C 0 10 N Y 1 F N
+F0 "C" 25 100 50 H V L CNN
+F1 "CP-Device" 25 -100 50 H V L CNN
+F2 "" 38 -150 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+$FPLIST
+ CP_*
+$ENDFPLIST
+DRAW
+S -90 20 90 40 0 1 0 N
+P 2 0 1 0 -70 90 -30 90 N
+P 2 0 1 0 -50 110 -50 70 N
+S 90 -20 -90 -40 0 1 0 F
+X ~ 1 0 150 110 D 50 50 1 1 P
+X ~ 2 0 -150 110 U 50 50 1 1 P
+ENDDRAW
+ENDDEF
+#
+# Jumper_3_Open-Jumper
+#
+DEF Jumper_3_Open-Jumper JP 0 0 Y N 1 F N
+F0 "JP" -100 -100 50 H V C CNN
+F1 "Jumper_3_Open-Jumper" 0 110 50 H V C CNN
+F2 "" 0 0 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+$FPLIST
+ Jumper*
+ TestPoint*3Pads*
+ TestPoint*Bridge*
+$ENDFPLIST
+DRAW
+C -130 0 20 0 0 0 N
+C 0 0 20 0 0 0 N
+C 130 0 20 0 0 0 N
+A -65 -30 89 518 1282 0 1 0 N -10 40 -120 40
+P 2 0 1 0 0 -20 0 -50 N
+A 65 -30 89 518 1282 0 1 0 N 120 40 10 40
+X A 1 -250 0 100 R 50 50 1 1 P
+X C 2 0 -150 100 U 50 50 1 1 I
+X B 3 250 0 100 L 50 50 1 1 P
+ENDDRAW
+ENDDEF
+#
+# YAAJ_BluePill-MCU_ST_STM32F1
+#
+DEF YAAJ_BluePill-MCU_ST_STM32F1 U 0 40 Y Y 1 F N
+F0 "U" -550 950 50 H V C CNN
+F1 "YAAJ_BluePill-MCU_ST_STM32F1" 0 250 50 V V C CNN
+F2 "my library:YAAJ_BluePill_2" -75 950 50 V I C CNN
+F3 "" -75 950 50 V I C CNN
+DRAW
+C -620 -800 14 0 0 0 F
+C -620 -700 14 0 0 0 F
+C -620 -600 14 0 0 0 F
+C -620 -500 14 0 0 0 F
+C -620 -400 14 0 0 0 F
+C -620 -300 14 0 0 0 F
+C -620 -200 14 0 0 0 F
+C -620 -100 14 0 0 0 F
+C -620 0 14 0 0 0 F
+C -620 100 14 0 0 0 F
+C -620 200 14 0 0 0 F
+C -620 300 14 0 0 0 F
+C -620 400 14 0 0 0 F
+C -620 500 14 0 0 0 F
+C -620 600 14 0 0 0 F
+C -620 800 14 0 0 0 F
+P 18 0 0 0 200 -970 225 -930 250 -970 200 -970 225 -935 245 -970 205 -965 225 -940 240 -970 210 -960 230 -945 235 -970 215 -955 235 -950 230 -965 220 -955 230 -960 225 -950 N
+P 18 0 0 0 725 -715 750 -675 775 -715 725 -715 750 -680 770 -715 730 -710 750 -685 765 -715 735 -705 755 -690 760 -715 740 -700 760 -695 755 -710 745 -700 755 -705 750 -695 N
+P 18 0 0 0 725 -615 750 -575 775 -615 725 -615 750 -580 770 -615 730 -610 750 -585 765 -615 735 -605 755 -590 760 -615 740 -600 760 -595 755 -610 745 -600 755 -605 750 -595 N
+P 18 0 0 0 725 -515 750 -475 775 -515 725 -515 750 -480 770 -515 730 -510 750 -485 765 -515 735 -505 755 -490 760 -515 740 -500 760 -495 755 -510 745 -500 755 -505 750 -495 N
+C 225 -1230 5 0 0 0 F
+C 225 -1230 10 0 0 0 N
+C 225 -1230 14 0 0 0 N
+C 620 600 10 0 0 0 F
+C 620 600 14 0 0 0 N
+C 620 700 10 0 0 0 F
+C 620 700 14 0 0 0 N
+S -600 900 600 -900 0 1 0 f
+P 6 0 1 0 -740 -800 -740 -820 -760 -820 -760 -780 -780 -780 -780 -800 N
+P 6 0 1 0 -740 -700 -740 -720 -760 -720 -760 -680 -780 -680 -780 -700 N
+P 6 0 1 0 -740 -600 -740 -620 -760 -620 -760 -580 -780 -580 -780 -600 N
+P 6 0 1 0 -740 -500 -740 -520 -760 -520 -760 -480 -780 -480 -780 -500 N
+P 6 0 1 0 -740 200 -740 180 -760 180 -760 220 -780 220 -780 200 N
+P 6 0 1 0 -740 300 -740 280 -760 280 -760 320 -780 320 -780 300 N
+P 6 0 1 0 -740 400 -740 380 -760 380 -760 420 -780 420 -780 400 N
+P 6 0 1 0 240 -1150 240 -1170 220 -1170 220 -1130 200 -1130 200 -1150 N
+P 6 0 1 0 780 -400 780 -420 760 -420 760 -380 740 -380 740 -400 N
+P 6 0 1 0 780 -300 780 -320 760 -320 760 -280 740 -280 740 -300 N
+P 6 0 1 0 780 -200 780 -220 760 -220 760 -180 740 -180 740 -200 N
+P 6 0 1 0 780 -100 780 -120 760 -120 760 -80 740 -80 740 -100 N
+P 6 0 1 0 780 200 780 180 760 180 760 220 740 220 740 200 N
+P 6 0 1 0 780 300 780 280 760 280 760 320 740 320 740 300 N
+P 6 0 1 0 780 400 780 380 760 380 760 420 740 420 740 400 N
+P 6 0 1 0 780 500 780 480 760 480 760 520 740 520 740 500 N
+C -620 700 14 1 1 0 F
+T 0 440 -1065 39 0 0 0 "30pF 2MHz" Normal 0 C C
+T 0 440 -1230 39 0 0 0 "5V tolerant" Normal 0 C C
+T 0 305 -400 39 0 0 0 ADC0 Normal 0 C C
+T 0 305 -300 39 0 0 0 ADC1 Normal 0 C C
+T 0 305 -200 39 0 0 0 ADC2 Normal 0 C C
+T 0 305 -105 39 0 0 0 ADC3 Normal 0 C C
+T 0 305 0 39 0 0 0 ADC4 Normal 0 C C
+T 0 300 400 39 0 0 0 ADC8 Normal 0 C C
+T 0 300 500 39 0 0 0 ADC9 Normal 0 C C
+T 0 290 -695 39 0 0 0 LED Normal 0 C C
+T 0 295 200 39 0 0 0 MISO1 Normal 0 C C
+T 0 295 300 39 0 0 0 MOSI1 Normal 0 C C
+T 0 -270 -95 39 0 0 0 NSS1 Normal 0 C C
+T 0 395 -1150 39 0 0 0 "PWM pin" Normal 0 C C
+T 0 -290 195 39 0 0 0 RX1 Normal 0 C C
+T 0 150 -105 39 0 0 0 RX2 Normal 0 C C
+T 0 280 700 39 0 0 0 RX3 Normal 0 C C
+T 0 305 100 39 0 0 0 SCK1 Normal 0 C C
+T 0 -275 -495 39 0 0 0 SCL1 Normal 0 C C
+T 0 -275 -600 39 0 0 0 SDA1 Normal 0 C C
+T 0 405 -945 39 0 0 0 "sink 3mA" Normal 0 C C
+T 0 445 -1000 39 0 0 0 "source 0mA" Normal 0 C C
+T 0 -295 300 39 0 0 0 TX1 Normal 0 C C
+T 0 150 -200 39 0 0 0 TX2 Normal 0 C C
+T 0 285 600 39 0 0 0 TX3 Normal 0 C C
+T 0 -265 0 39 0 0 0 USB+ Normal 0 C C
+T 0 -265 100 39 0 0 0 USB- Normal 0 C C
+T 0 539 -872 20 0 0 0 Y@@J Normal 0 C C
+X PB12 1 -800 800 200 R 50 50 1 1 B
+X PA15 10 -800 -100 200 R 50 50 1 1 B
+X PB3 11 -800 -200 200 R 50 50 1 1 B
+X PB4 12 -800 -300 200 R 50 50 1 1 B
+X PB5 13 -800 -400 200 R 50 50 1 1 B
+X PB6 14 -800 -500 200 R 50 50 1 1 B
+X PB7 15 -800 -600 200 R 50 50 1 1 B
+X PB8 16 -800 -700 200 R 50 50 1 1 B
+X PB9 17 -800 -800 200 R 50 50 1 1 B
+X 5V 18 -100 1100 200 D 50 50 1 1 W
+X GND 19 -200 -1100 200 U 50 50 1 1 W
+X PB13 2 -800 700 200 R 50 50 1 1 B
+X 3V3 20 0 1100 200 D 50 50 1 1 W
+X VBat 21 -200 1100 200 D 50 50 1 1 W
+X PC13 22 800 -700 200 L 50 50 1 1 B
+X PC14 23 800 -600 200 L 50 50 1 1 B
+X PC15 24 800 -500 200 L 50 50 1 1 B
+X PA0 25 800 -400 200 L 50 50 1 1 B
+X PA1 26 800 -300 200 L 50 50 1 1 B
+X PA2 27 800 -200 200 L 50 50 1 1 B
+X PA3 28 800 -100 200 L 50 50 1 1 B
+X PA4 29 800 0 200 L 50 50 1 1 B
+X PB14 3 -800 600 200 R 50 50 1 1 B
+X PA5 30 800 100 200 L 50 50 1 1 B
+X PA6 31 800 200 200 L 50 50 1 1 B
+X PA7 32 800 300 200 L 50 50 1 1 B
+X PB0 33 800 400 200 L 50 50 1 1 B
+X PB1 34 800 500 200 L 50 50 1 1 B
+X PB10 35 800 600 200 L 50 50 1 1 B
+X PB11 36 800 700 200 L 50 50 1 1 B
+X RST 37 800 800 200 L 50 50 1 1 I
+X 3V3 38 100 1100 200 D 50 50 1 1 W
+X GND 39 -100 -1100 200 U 50 50 1 1 W
+X PB15 4 -800 500 200 R 50 50 1 1 B
+X GND 40 0 -1100 200 U 50 50 1 1 W
+X PA8 5 -800 400 200 R 50 50 1 1 B
+X PA9 6 -800 300 200 R 50 50 1 1 B
+X PA10 7 -800 200 200 R 50 50 1 1 B
+X PA11 8 -800 100 200 R 50 50 1 1 B
+X PA12 9 -800 0 200 R 50 50 1 1 B
+ENDDRAW
+ENDDEF
+#
+#End Library

kicad/bluescsi_iigs_internal.kicad_prl

@@ -0,0 +1,75 @@
+{
+  "board": {
+    "active_layer": 31,
+    "active_layer_preset": "All Layers",
+    "auto_track_width": true,
+    "hidden_nets": [],
+    "high_contrast_mode": 0,
+    "net_color_mode": 1,
+    "opacity": {
+      "pads": 1.0,
+      "tracks": 1.0,
+      "vias": 1.0,
+      "zones": 0.6
+    },
+    "ratsnest_display_mode": 0,
+    "selection_filter": {
+      "dimensions": true,
+      "footprints": true,
+      "graphics": true,
+      "keepouts": true,
+      "lockedItems": true,
+      "otherItems": true,
+      "pads": true,
+      "text": true,
+      "tracks": true,
+      "vias": true,
+      "zones": true
+    },
+    "visible_items": [
+      0,
+      1,
+      2,
+      3,
+      4,
+      5,
+      8,
+      9,
+      10,
+      11,
+      12,
+      13,
+      14,
+      15,
+      16,
+      17,
+      18,
+      19,
+      20,
+      21,
+      22,
+      23,
+      24,
+      25,
+      26,
+      27,
+      28,
+      29,
+      30,
+      32,
+      33,
+      34,
+      35,
+      36
+    ],
+    "visible_layers": "fffffff_ffffffff",
+    "zone_display_mode": 0
+  },
+  "meta": {
+    "filename": "bluescsi_iigs_internal.kicad_prl",
+    "version": 3
+  },
+  "project": {
+    "files": []
+  }
+}

kicad/bluescsi_iigs_internal.kicad_pro

@@ -0,0 +1,494 @@
+{
+  "board": {
+    "design_settings": {
+      "defaults": {
+        "board_outline_line_width": 0.049999999999999996,
+        "copper_line_width": 0.19999999999999998,
+        "copper_text_italic": false,
+        "copper_text_size_h": 1.5,
+        "copper_text_size_v": 1.5,
+        "copper_text_thickness": 0.3,
+        "copper_text_upright": false,
+        "courtyard_line_width": 0.049999999999999996,
+        "dimension_precision": 4,
+        "dimension_units": 3,
+        "dimensions": {
+          "arrow_length": 1270000,
+          "extension_offset": 500000,
+          "keep_text_aligned": true,
+          "suppress_zeroes": false,
+          "text_position": 0,
+          "units_format": 1
+        },
+        "fab_line_width": 0.09999999999999999,
+        "fab_text_italic": false,
+        "fab_text_size_h": 1.0,
+        "fab_text_size_v": 1.0,
+        "fab_text_thickness": 0.15,
+        "fab_text_upright": false,
+        "other_line_width": 0.09999999999999999,
+        "other_text_italic": false,
+        "other_text_size_h": 1.0,
+        "other_text_size_v": 1.0,
+        "other_text_thickness": 0.15,
+        "other_text_upright": false,
+        "pads": {
+          "drill": 0.762,
+          "height": 1.524,
+          "width": 1.524
+        },
+        "silk_line_width": 0.12,
+        "silk_text_italic": false,
+        "silk_text_size_h": 1.0,
+        "silk_text_size_v": 1.0,
+        "silk_text_thickness": 0.15,
+        "silk_text_upright": false,
+        "zones": {
+          "45_degree_only": false,
+          "min_clearance": 0.508
+        }
+      },
+      "diff_pair_dimensions": [
+        {
+          "gap": 0.0,
+          "via_gap": 0.0,
+          "width": 0.0
+        }
+      ],
+      "drc_exclusions": [],
+      "meta": {
+        "filename": "board_design_settings.json",
+        "version": 2
+      },
+      "rule_severities": {
+        "annular_width": "error",
+        "clearance": "error",
+        "copper_edge_clearance": "error",
+        "courtyards_overlap": "error",
+        "diff_pair_gap_out_of_range": "error",
+        "diff_pair_uncoupled_length_too_long": "error",
+        "drill_out_of_range": "error",
+        "duplicate_footprints": "warning",
+        "extra_footprint": "warning",
+        "footprint_type_mismatch": "error",
+        "hole_clearance": "error",
+        "hole_near_hole": "error",
+        "invalid_outline": "error",
+        "item_on_disabled_layer": "error",
+        "items_not_allowed": "error",
+        "length_out_of_range": "error",
+        "malformed_courtyard": "error",
+        "microvia_drill_out_of_range": "error",
+        "missing_courtyard": "ignore",
+        "missing_footprint": "warning",
+        "net_conflict": "warning",
+        "npth_inside_courtyard": "ignore",
+        "padstack": "error",
+        "pth_inside_courtyard": "ignore",
+        "shorting_items": "error",
+        "silk_over_copper": "warning",
+        "silk_overlap": "warning",
+        "skew_out_of_range": "error",
+        "through_hole_pad_without_hole": "error",
+        "too_many_vias": "error",
+        "track_dangling": "warning",
+        "track_width": "error",
+        "tracks_crossing": "error",
+        "unconnected_items": "error",
+        "unresolved_variable": "error",
+        "via_dangling": "warning",
+        "zone_has_empty_net": "error",
+        "zones_intersect": "error"
+      },
+      "rule_severitieslegacy_courtyards_overlap": true,
+      "rule_severitieslegacy_no_courtyard_defined": false,
+      "rules": {
+        "allow_blind_buried_vias": false,
+        "allow_microvias": false,
+        "max_error": 0.005,
+        "min_clearance": 0.19999999999999998,
+        "min_copper_edge_clearance": 0.024999999999999998,
+        "min_hole_clearance": 0.25,
+        "min_hole_to_hole": 0.25,
+        "min_microvia_diameter": 0.19999999999999998,
+        "min_microvia_drill": 0.09999999999999999,
+        "min_silk_clearance": 0.0,
+        "min_through_hole_diameter": 0.3,
+        "min_track_width": 0.19999999999999998,
+        "min_via_annular_width": 0.049999999999999996,
+        "min_via_diameter": 0.39999999999999997,
+        "use_height_for_length_calcs": true
+      },
+      "track_widths": [
+        0.0
+      ],
+      "via_dimensions": [
+        {
+          "diameter": 0.0,
+          "drill": 0.0
+        }
+      ],
+      "zones_allow_external_fillets": false,
+      "zones_use_no_outline": true
+    },
+    "layer_presets": []
+  },
+  "boards": [],
+  "cvpcb": {
+    "equivalence_files": []
+  },
+  "erc": {
+    "erc_exclusions": [],
+    "meta": {
+      "version": 0
+    },
+    "pin_map": [
+      [
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        1,
+        0,
+        0,
+        0,
+        0,
+        2
+      ],
+      [
+        0,
+        2,
+        0,
+        1,
+        0,
+        0,
+        1,
+        0,
+        2,
+        2,
+        2,
+        2
+      ],
+      [
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        1,
+        0,
+        1,
+        0,
+        1,
+        2
+      ],
+      [
+        0,
+        1,
+        0,
+        0,
+        0,
+        0,
+        1,
+        1,
+        2,
+        1,
+        1,
+        2
+      ],
+      [
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        1,
+        0,
+        0,
+        0,
+        0,
+        2
+      ],
+      [
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        0,
+        2
+      ],
+      [
+        1,
+        1,
+        1,
+        1,
+        1,
+        0,
+        1,
+        1,
+        1,
+        1,
+        1,
+        2
+      ],
+      [
+        0,
+        0,
+        0,
+        1,
+        0,
+        0,
+        1,
+        0,
+        0,
+        0,
+        0,
+        2
+      ],
+      [
+        0,
+        2,
+        1,
+        2,
+        0,
+        0,
+        1,
+        0,
+        2,
+        2,
+        2,
+        2
+      ],
+      [
+        0,
+        2,
+        0,
+        1,
+        0,
+        0,
+        1,
+        0,
+        2,
+        0,
+        0,
+        2
+      ],
+      [
+        0,
+        2,
+        1,
+        1,
+        0,
+        0,
+        1,
+        0,
+        2,
+        0,
+        0,
+        2
+      ],
+      [
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2,
+        2
+      ]
+    ],
+    "rule_severities": {
+      "bus_definition_conflict": "error",
+      "bus_entry_needed": "error",
+      "bus_label_syntax": "error",
+      "bus_to_bus_conflict": "error",
+      "bus_to_net_conflict": "error",
+      "different_unit_footprint": "error",
+      "different_unit_net": "error",
+      "duplicate_reference": "error",
+      "duplicate_sheet_names": "error",
+      "extra_units": "error",
+      "global_label_dangling": "warning",
+      "hier_label_mismatch": "error",
+      "label_dangling": "error",
+      "lib_symbol_issues": "warning",
+      "multiple_net_names": "warning",
+      "net_not_bus_member": "warning",
+      "no_connect_connected": "warning",
+      "no_connect_dangling": "warning",
+      "pin_not_connected": "error",
+      "pin_not_driven": "error",
+      "pin_to_pin": "warning",
+      "power_pin_not_driven": "error",
+      "similar_labels": "warning",
+      "unannotated": "error",
+      "unit_value_mismatch": "error",
+      "unresolved_variable": "error",
+      "wire_dangling": "error"
+    }
+  },
+  "libraries": {
+    "pinned_footprint_libs": [],
+    "pinned_symbol_libs": []
+  },
+  "meta": {
+    "filename": "bluescsi_iigs_internal.kicad_pro",
+    "version": 1
+  },
+  "net_settings": {
+    "classes": [
+      {
+        "bus_width": 12.0,
+        "clearance": 0.2,
+        "diff_pair_gap": 0.25,
+        "diff_pair_via_gap": 0.25,
+        "diff_pair_width": 0.2,
+        "line_style": 0,
+        "microvia_diameter": 0.3,
+        "microvia_drill": 0.1,
+        "name": "Default",
+        "pcb_color": "rgba(0, 0, 0, 0.000)",
+        "schematic_color": "rgba(0, 0, 0, 0.000)",
+        "track_width": 0.25,
+        "via_diameter": 0.8,
+        "via_drill": 0.4,
+        "wire_width": 6.0
+      },
+      {
+        "bus_width": 12.0,
+        "clearance": 0.2,
+        "diff_pair_gap": 0.25,
+        "diff_pair_via_gap": 0.25,
+        "diff_pair_width": 0.2,
+        "line_style": 0,
+        "microvia_diameter": 0.3,
+        "microvia_drill": 0.1,
+        "name": "12V",
+        "nets": [],
+        "pcb_color": "rgba(0, 0, 0, 0.000)",
+        "schematic_color": "rgba(0, 0, 0, 0.000)",
+        "track_width": 0.35,
+        "via_diameter": 0.8,
+        "via_drill": 0.4,
+        "wire_width": 6.0
+      },
+      {
+        "bus_width": 12.0,
+        "clearance": 0.2,
+        "diff_pair_gap": 0.25,
+        "diff_pair_via_gap": 0.25,
+        "diff_pair_width": 0.2,
+        "line_style": 0,
+        "microvia_diameter": 0.3,
+        "microvia_drill": 0.1,
+        "name": "3.3V",
+        "nets": [
+          "+3V3"
+        ],
+        "pcb_color": "rgba(0, 0, 0, 0.000)",
+        "schematic_color": "rgba(0, 0, 0, 0.000)",
+        "track_width": 0.3,
+        "via_diameter": 0.8,
+        "via_drill": 0.4,
+        "wire_width": 6.0
+      },
+      {
+        "bus_width": 12.0,
+        "clearance": 0.2,
+        "diff_pair_gap": 0.25,
+        "diff_pair_via_gap": 0.25,
+        "diff_pair_width": 0.2,
+        "line_style": 0,
+        "microvia_diameter": 0.3,
+        "microvia_drill": 0.1,
+        "name": "5V",
+        "nets": [
+          "+5V",
+          "/+5V_AUX",
+          "/SCSI_TERMPWR"
+        ],
+        "pcb_color": "rgba(0, 0, 0, 0.000)",
+        "schematic_color": "rgba(0, 0, 0, 0.000)",
+        "track_width": 0.4,
+        "via_diameter": 0.8,
+        "via_drill": 0.4,
+        "wire_width": 6.0
+      }
+    ],
+    "meta": {
+      "version": 2
+    },
+    "net_colors": null
+  },
+  "pcbnew": {
+    "last_paths": {
+      "gencad": "",
+      "idf": "",
+      "netlist": "",
+      "specctra_dsn": "",
+      "step": "",
+      "vrml": ""
+    },
+    "page_layout_descr_file": ""
+  },
+  "schematic": {
+    "annotate_start_num": 0,
+    "drawing": {
+      "default_line_thickness": 6.0,
+      "default_text_size": 50.0,
+      "field_names": [],
+      "intersheets_ref_own_page": false,
+      "intersheets_ref_prefix": "",
+      "intersheets_ref_short": false,
+      "intersheets_ref_show": false,
+      "intersheets_ref_suffix": "",
+      "junction_size_choice": 3,
+      "label_size_ratio": 0.25,
+      "pin_symbol_size": 0.0,
+      "text_offset_ratio": 0.08
+    },
+    "legacy_lib_dir": "",
+    "legacy_lib_list": [],
+    "meta": {
+      "version": 1
+    },
+    "net_format_name": "",
+    "ngspice": {
+      "fix_include_paths": true,
+      "fix_passive_vals": false,
+      "meta": {
+        "version": 0
+      },
+      "model_mode": 0,
+      "workbook_filename": ""
+    },
+    "page_layout_descr_file": "",
+    "plot_directory": "",
+    "spice_adjust_passive_values": false,
+    "spice_external_command": "spice \"%I\"",
+    "subpart_first_id": 65,
+    "subpart_id_separator": 0
+  },
+  "sheets": [
+    [
+      "e7bb7815-0d52-4bb8-b29a-8cf960bd2905",
+      ""
+    ]
+  ],
+  "text_variables": {}
+}

kicad/bluescsi_iigs_internal.pro

@@ -1,4 +1,4 @@
-update=Friday, April 30, 2021 at 05:58:20 PM
+update=Thursday, June 17, 2021 at 05:45:58 PM
 version=1
 last_client=kicad
 [general]
@@ -239,7 +239,7 @@ dPairViaGap=0.25
 [pcbnew/Netclasses/1]
 Name=POWER
 Clearance=0.2
-TrackWidth=0.3
+TrackWidth=0.31
 ViaDiameter=0.8
 ViaDrill=0.4
 uViaDiameter=0.3

kicad/fp-info-cache

@@ -1,148 +0,0 @@
-33695039091627
-Jumper
-SolderJumper-2_P1.3mm_Bridged2Bar_Pad1.0x1.5mm
-SMD Solder Jumper, 1x1.5mm Pads, 0.3mm gap, bridged with 2 copper strips
-solder jumper open
-0
-2
-2
-Jumper
-SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mm
-SMD Solder Jumper, 1x1.5mm, rounded Pads, 0.3mm gap, bridged with 2 copper strips
-solder jumper open
-0
-2
-2
-Jumper
-SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm
-SMD Solder Jumper, 1x1.5mm Pads, 0.3mm gap, bridged with 1 copper strip
-solder jumper open
-0
-2
-2
-Jumper
-SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm
-SMD Solder Jumper, 1x1.5mm, rounded Pads, 0.3mm gap, bridged with 1 copper strip
-solder jumper open
-0
-2
-2
-Jumper
-SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm
-SMD Solder Jumper, 1x1.5mm Pads, 0.3mm gap, open
-solder jumper open
-0
-2
-2
-Jumper
-SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm
-SMD Solder Jumper, 1x1.5mm, rounded Pads, 0.3mm gap, open
-solder jumper open
-0
-2
-2
-Jumper
-SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm
-SMD Solder Jumper, 1x1.5mm Triangular Pads, 0.3mm gap, open
-solder jumper open
-0
-2
-2
-Jumper
-SolderJumper-3_P1.3mm_Bridged2Bar12_Pad1.0x1.5mm
-SMD Solder 3-pad Jumper, 1x1.5mm Pads, 0.3mm gap, pads 1-2 Bridged2Bar with 2 copper strip
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Bridged2Bar12_Pad1.0x1.5mm_NumberLabels
-SMD Solder Jumper, 1x1.5mm Pads, 0.3mm gap, pads 1-2 Bridged2Bar with 2 copper strip, labeled with numbers
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Bridged2Bar12_RoundedPad1.0x1.5mm
-SMD Solder 3-pad Jumper, 1x1.5mm rounded Pads, 0.3mm gap, pads 1-2 Bridged2Bar with 2 copper strip
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Bridged2Bar12_RoundedPad1.0x1.5mm_NumberLabels
-SMD Solder 3-pad Jumper, 1x1.5mm rounded Pads, 0.3mm gap, pads 1-2 Bridged2Bar with 2 copper strip, labeled with numbers
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm
-SMD Solder 3-pad Jumper, 1x1.5mm Pads, 0.3mm gap, pads 1-2 bridged with 1 copper strip
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm_NumberLabels
-SMD Solder Jumper, 1x1.5mm Pads, 0.3mm gap, pads 1-2 bridged with 1 copper strip, labeled with numbers
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm
-SMD Solder 3-pad Jumper, 1x1.5mm rounded Pads, 0.3mm gap, pads 1-2 bridged with 1 copper strip
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels
-SMD Solder 3-pad Jumper, 1x1.5mm rounded Pads, 0.3mm gap, pads 1-2 bridged with 1 copper strip, labeled with numbers
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mm
-SMD Solder 3-pad Jumper, 1x1.5mm Pads, 0.3mm gap, open
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mm_NumberLabels
-SMD Solder Jumper, 1x1.5mm Pads, 0.3mm gap, open, labeled with numbers
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm
-SMD Solder 3-pad Jumper, 1x1.5mm rounded Pads, 0.3mm gap, open
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabels
-SMD Solder 3-pad Jumper, 1x1.5mm rounded Pads, 0.3mm gap, open, labeled with numbers
-solder jumper open
-0
-3
-3
-Jumper
-SolderJumper-3_P2.0mm_Open_TrianglePad1.0x1.5mm
-SMD Solder Jumper, 1x1.5mm Triangular Pads, 0.3mm gap, open
-solder jumper open
-0
-5
-3
-Jumper
-SolderJumper-3_P2.0mm_Open_TrianglePad1.0x1.5mm_NumberLabels
-SMD Solder Jumper, 1x1.5mm Triangular Pads, 0.3mm gap, open, labeled with numbers
-solder jumper open
-0
-5
-3

kicad/sym-lib-table

@@ -1,3 +1,5 @@
 (sym_lib_table
-  (lib (name 105162-0001)(type Legacy)(uri "${KIPRJMOD}/footprints/Molex 105162-0001/105162-0001.lib")(options "")(descr ""))
+  (lib (name "105162-0001")(type "Legacy")(uri "${KIPRJMOD}/footprints/Molex 105162-0001/105162-0001.lib")(options "")(descr ""))
+  (lib (name "bluescsi_iigs_internal-rescue")(type "Legacy")(uri "${KIPRJMOD}/bluescsi_iigs_internal-rescue.lib")(options "")(descr ""))
+  (lib (name "ucc3916")(type "KiCad")(uri "${KIPRJMOD}/ucc3916.kicad_sym")(options "")(descr ""))
 )

kicad/ucc3916.kicad_sym

@@ -0,0 +1,56 @@
+(kicad_symbol_lib (version 20211014) (generator kicad_symbol_editor)
+  (symbol "UCC3916" (in_bom yes) (on_board yes)
+    (property "Reference" "U" (id 0) (at 0 2.54 0)
+      (effects (font (size 1.27 1.27)))
+    )
+    (property "Value" "UCC3916" (id 1) (at 0 5.08 0)
+      (effects (font (size 1.27 1.27)))
+    )
+    (property "Footprint" "" (id 2) (at 0 0 0)
+      (effects (font (size 1.27 1.27)) hide)
+    )
+    (property "Datasheet" "" (id 3) (at 0 0 0)
+      (effects (font (size 1.27 1.27)) hide)
+    )
+    (symbol "UCC3916_0_1"
+      (rectangle (start -7.62 1.27) (end 7.62 -11.43)
+        (stroke (width 0) (type default) (color 0 0 0 0))
+        (fill (type none))
+      )
+    )
+    (symbol "UCC3916_1_1"
+      (pin input line (at -10.16 -1.27 0) (length 2.54)
+        (name "VIN" (effects (font (size 1.27 1.27))))
+        (number "1" (effects (font (size 1.27 1.27))))
+      )
+      (pin output line (at -10.16 -3.81 0) (length 2.54)
+        (name "GND" (effects (font (size 1.27 1.27))))
+        (number "2" (effects (font (size 1.27 1.27))))
+      )
+      (pin output line (at -10.16 -6.35 0) (length 2.54)
+        (name "GND" (effects (font (size 1.27 1.27))))
+        (number "3" (effects (font (size 1.27 1.27))))
+      )
+      (pin bidirectional line (at -10.16 -8.89 0) (length 2.54)
+        (name "CT" (effects (font (size 1.27 1.27))))
+        (number "4" (effects (font (size 1.27 1.27))))
+      )
+      (pin input line (at 10.16 -8.89 180) (length 2.54)
+        (name "/SHTDWN" (effects (font (size 1.27 1.27))))
+        (number "5" (effects (font (size 1.27 1.27))))
+      )
+      (pin output line (at 10.16 -6.35 180) (length 2.54)
+        (name "GND" (effects (font (size 1.27 1.27))))
+        (number "6" (effects (font (size 1.27 1.27))))
+      )
+      (pin output line (at 10.16 -3.81 180) (length 2.54)
+        (name "GND" (effects (font (size 1.27 1.27))))
+        (number "7" (effects (font (size 1.27 1.27))))
+      )
+      (pin output line (at 10.16 -1.27 180) (length 2.54)
+        (name "OUTPUT" (effects (font (size 1.27 1.27))))
+        (number "8" (effects (font (size 1.27 1.27))))
+      )
+    )
+  )
+)