diff --git a/hardware/documents/Keyboard_build.md b/hardware/documents/Keyboard_build.md
index 13bcee3..afa394b 100644
--- a/hardware/documents/Keyboard_build.md
+++ b/hardware/documents/Keyboard_build.md
@@ -11,21 +11,21 @@ The aligner PCB includes a guide for bending the stabilizer.
 
 1. Start by creating a 90 degree bend about 2 cm from the end of the rod.  This allows enough room to clip the end down to the correct length later.
 
-    <img alt="First Bend" src="build-images/rod_first_bend.jpg" height=75% width=75%>
+    <img alt="First Bend" src="build-images/rod_first_bend.jpg" height=50% width=50%>
 
 1. Insert the bent end into one guide hole, and, keeping the rod as flat to the board as possible, use the second guide hole to estimate the position of the second bend.  Your estimate should be about 1mm short to allow for a bending radius.  Once you have the pliers positioned on the rod, make your 90 degree bend.
 
-    <img alt="Insert Rod in Guide" src="build-images/rod_insert_first_arm.jpg" height=75% width=75%>
+    <img alt="Insert Rod in Guide" src="build-images/rod_insert_first_arm.jpg" height=50% width=50%>
 
 1. Look along the length of the rod to make sure that both "arms" are in line.  If necessary, align the two arms by twisting about the axis of the axis of the rod.
 
 1. Test the fit of the rod by inserting it into the guide holes.  You can see, in this example, the rod is a tad long.
 
-    <img alt="Test Fit" src="build-images/test_fit_too_long.jpg" height=75% width=75%>
+    <img alt="Test Fit" src="build-images/test_fit_too_long.jpg" height=50% width=50%>
 
 1. Clip the arms of the rod to about 11 mm.
 
-    <img alt="Clip Arms to Length" src="build-images/stabilizer_rod_timmed_arms.jpg" height=75% width=75%>
+    <img alt="Clip Arms to Length" src="build-images/stabilizer_rod_timmed_arms.jpg" height=50% width=50%>
 
 
 1. Install the Cherry MX stabilizers to the board.
@@ -39,9 +39,11 @@ See the Cherry MX section above for notes on installing the Cherry MX stabilizer
 ##### Longer Stabilizer posts for Futaba
 The Futaba aligner PCB includes two stabilizer posts, allowing the futaba keys to be used with the Cherry MX PCB-mount stabilizers.
 
+    <img alt="Futaba stabilizer adapter posts" src="pre-breakaway.jpg" height=50% width=50%>
+
 1. Remove both posts from the PCB.  Newer revisions of the aligner board include perforations for easier break-away of the posts.
 
-    <img alt="Break away posts from aligner" src="build-images/cutting_post.jpg" height=75% width=75%>
+    <img alt="Break away posts from aligner" src="build-images/cutting_post.jpg" height=50% width=50%>
 
 1. Be sure to file away any excess material from the breakaway tab.
 
@@ -49,27 +51,25 @@ The Futaba aligner PCB includes two stabilizer posts, allowing the futaba keys t
 
 1. File away the area marked "File to 1.5mm".  The aligner includes a thickness gauge to test fitting, but it turns out that manufacturing tolerances are not adequate, and the gauge is not reliable.  Use a spare key to test the thickness.  The post should require some pressure to inert into the keycap base.
 
-<img alt="" src="" height=75% width=75%>
+<img alt="" src="" height=50% width=50%>
 
 1. The post should be just under 4mm wide.  The post in this example is an early revision that was specified at 4mm, and ended being a sliver too wide to fit the keycap base.  It required a alittle extra filing along one side to fit properly.
 
-<img alt="" src="" height=75% width=75%>
+   <img alt="Posts before and after filing" src="build-images/futaba_posts_before_and_after.jpg" height=50% width=50%>
 
-1. Here is an example of posts before and after filing.  You may notice the small bump along the left side of the upper left post.  That got filed off after the photo was taken.
-
-   <img alt="" src="" height=75% width=75%>
+    <img alt="Posts ready to install" src="build-images/filed_futaba_posts.jpg" height=50% width=50%>
 
 1. The posts should be just tight enough to require a pair of pliers to insert.  Use pliers to insert both posts fully.  Use a ruler or caliper to ensure the prodruding portions of both posts are the same length.
 
-<img alt="" src="" height=75% width=75%>
+<img alt="" src="" height=50% width=50%>
 
 1. Install the spacebar center mount on the spacebar key, aligning the posts so that they slide into the PCB-mounted stabilizers.
 
-<img alt="" src="" height=75% width=75%>
+<img alt="" src="" height=50% width=50%>
 
 1. Holding down the spacebar, align the arms stabilizer rod with the holes in the posts, and then snap the rod into place at the front of the stabilizer mounts.
 
-<img alt="Stabilizer installed" src="build-images/stabilizer_installed_futaba.jpg" height=75% width=75%>
+<img alt="Stabilizer installed" src="build-images/stabilizer_installed_futaba.jpg" height=50% width=50%>
 
 
 
diff --git a/hardware/documents/build-images/cutting_post.jpg b/hardware/documents/build-images/cutting_post.jpg
index 8024563..fa92015 100644
Binary files a/hardware/documents/build-images/cutting_post.jpg and b/hardware/documents/build-images/cutting_post.jpg differ