blink blue but with the timer.

Makefile

@@ -74,7 +74,7 @@ tests/rftest-tx.obj: src/maca.o src/nvm.o
 		$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
 
 %.dis:		%.obj
-		$(OBJDUMP) -D $< > $@
+		$(OBJDUMP) -SD $< > $@
 
 %.obj:		$(LDSCRIPT) %.o
 		$(LD) $(LDFLAGS) $(AOBJS) \

tests/tmr.c

@@ -0,0 +1,92 @@
+/* Timer registers are all 16-bit wide with 16-bit access only */
+#define TMR_OFFSET      (0x20)
+#define TMR_BASE        (0x80007000)
+#define TMR0_BASE       (TMR_BASE)
+#define TMR1_BASE       (TMR_BASE + TMR_OFFSET*1)
+#define TMR2_BASE       (TMR_BASE + TMR_OFFSET*2)
+#define TMR3_BASE       (TMR_BASE + TMR_OFFSET*3)
+
+#define TMR_REGOFF_COMP1    (0x0)
+#define TMR_REGOFF_COMP2    (0x2)
+#define TMR_REGOFF_CAPT     (0x4)
+#define TMR_REGOFF_LOAD     (0x6)
+#define TMR_REGOFF_HOLD     (0x8)
+#define TMR_REGOFF_CNTR     (0xa)
+#define TMR_REGOFF_CTRL     (0xc)
+#define TMR_REGOFF_SCTRL    (0xe)
+#define TMR_REGOFF_CMPLD1   (0x10)
+#define TMR_REGOFF_CMPLD2   (0x12)
+#define TMR_REGOFF_CSCTRL   (0x14)
+#define TMR_REGOFF_ENBL     (0x1e)
+
+/* Timer 0 registers */
+#define TMR0_COMP1   (TMR0_BASE + TMR_REGOFF_COMP1)
+#define TMR0_COMP_UP TMR0_COMP1
+#define TMR0_COMP2   (TMR0_BASE + TMR_REGOFF_COMP2)
+#define TMR0_COMP_DOWN TMR0_COMP2
+#define TMR0_CAPT    (TMR0_BASE + TMR_REGOFF_CAPT)
+#define TMR0_LOAD    (TMR0_BASE + TMR_REGOFF_LOAD)
+#define TMR0_HOLD    (TMR0_BASE + TMR_REGOFF_HOLD)
+#define TMR0_CNTR    (TMR0_BASE + TMR_REGOFF_CTRL)
+#define TMR0_CTRL    (TMR0_BASE + TMR_REGOFF_CTRL)
+#define TMR0_SCTRL   (TMR0_BASE + TMR_REGOFF_SCTRL)
+#define TMR0_CMPLD1  (TMR0_BASE + TMR_REGOFF_CMPLD1)
+#define TMR0_CMPLD2  (TMR0_BASE + TMR_REGOFF_CMPLD2)
+#define TMR0_CSCTRL  (TMR0_BASE + TMR_REGOFF_CSCTRL)
+
+/* one enable register to rule them all */
+#define TMR_ENBL    TMR0_BASE + TMR_REGOFF_ENBL
+
+#define MBAR_GPIO       0x80000000
+#define GPIO_PAD_DIR0   0x80000000
+#define GPIO_DATA0      0x80000008
+#define UART1_DATA      0x80005008
+#define DELAY 400000
+
+#define reg32(x) (*(volatile uint32_t *)(x))
+#define reg16(x) (*(volatile uint16_t *)(x))
+
+#include "embedded_types.h"
+
+__attribute__ ((section ("startup")))
+void main(void) {
+
+	/* pin direction */
+	reg32(GPIO_PAD_DIR0) = 0x00000400;
+
+	/* timer setup */
+	/* CTRL */
+#define COUNT_MODE 1      /* use rising edge of primary source */
+#define PRIME_SRC  0xf    /* Perip. clock with 128 prescale (for 24Mhz = 187500Hz)*/
+#define SEC_SRC    0      /* don't need this */
+#define ONCE       0      /* keep counting */
+#define LEN        1      /* count until compare then reload with value in LOAD */
+#define DIR        0      /* count up */
+#define CO_INIT    0      /* other counters cannot force a re-initialization of this counter */
+#define OUT_MODE   0      /* OFLAG is asserted while counter is active */
+
+	reg16(TMR_ENBL) = 0;                     /* tmrs reset to enabled */
+	reg16(TMR0_SCTRL) = 0;
+	reg16(TMR0_LOAD) = 0;                    /* reload to zero */
+	reg16(TMR0_COMP_UP) = 18750;             /* trigger a reload at the end */
+	reg16(TMR0_CMPLD1) = 18750;              /* compare 1 triggered reload level, 10HZ maybe? */
+	reg16(TMR0_CNTR) = 0;                    /* reset count register */
+	reg16(TMR0_CTRL) = (COUNT_MODE<<13) | (PRIME_SRC<<9) | (SEC_SRC<<7) | (ONCE<<6) | (LEN<<5) | (DIR<<4) | (CO_INIT<<3) | (OUT_MODE);
+	reg16(TMR_ENBL) = 0xf;                   /* enable all the timers --- why not? */
+
+	while(1) {
+
+		/* blink on */
+		reg32(GPIO_DATA0) = 0x00000400;
+		
+		while((reg16(TMR0_SCTRL)>>15) == 0) { continue; }
+		reg16(TMR0_SCTRL) = 0; /*clear bit 15, and all the others --- should be ok, but clearly not "the right thing to do" */
+
+		/* blink off */
+		reg32(GPIO_DATA0) = 0x00000000;
+
+		while((reg16(TMR0_SCTRL)>>15) == 0) { continue; }
+		reg16(TMR0_SCTRL) = 0; /*clear bit 15, and all the others --- should be ok, but clearly not "the right thing to do" */
+
+	};
+}