mirror of
https://github.com/oliverschmidt/contiki.git
synced 2024-12-21 19:29:18 +00:00
Refactor with settings manager and better usb enumeration for debug prints
This commit is contained in:
dak664
parent
a9cbbb4570
commit
fcb41fa5c2
@ -42,9 +42,9 @@
|
||||
|
||||
#define DEBUG 0
|
||||
#if DEBUG
|
||||
#define PRINTF(FORMAT,args...) printf_P(PSTR(FORMAT),##args)
|
||||
#define PRINTD(FORMAT,args...) printf_P(PSTR(FORMAT),##args)
|
||||
#else
|
||||
#define PRINTF(...)
|
||||
#define PRINTD(...)
|
||||
#endif
|
||||
|
||||
#include <avr/pgmspace.h>
|
||||
@ -67,6 +67,13 @@
|
||||
/* Set ANNOUNCE to send boot messages to USB or RS232 serial port */
|
||||
#define ANNOUNCE 1
|
||||
|
||||
/* But only if a serial port exists */
|
||||
#if USB_CONF_SERIAL||USB_CONF_RS232
|
||||
#define PRINTA(FORMAT,args...) printf_P(PSTR(FORMAT),##args)
|
||||
#else
|
||||
#define PRINTA(...)
|
||||
#endif
|
||||
|
||||
#include "usb_task.h"
|
||||
#if USB_CONF_SERIAL
|
||||
#include "cdc_task.h"
|
||||
@ -101,11 +108,13 @@ rimeaddr_t macLongAddr;
|
||||
#include "ieee-15-4-manager.h"
|
||||
#endif /* RF230BB */
|
||||
|
||||
/* Test rtimers, also useful for pings and time stamps in simulator */
|
||||
/* Test rtimers, also useful for pings, time stamps, routes, stack monitor */
|
||||
#define TESTRTIMER 0
|
||||
#if TESTRTIMER
|
||||
#define PINGS 0
|
||||
#define STAMPS 30
|
||||
#define STAMPS 60
|
||||
#define ROUTES 120
|
||||
#define STACKMONITOR 600
|
||||
uint8_t rtimerflag=1;
|
||||
uint16_t rtime;
|
||||
struct rtimer rt;
|
||||
@ -116,6 +125,7 @@ void rtimercycle(void) {rtimerflag=1;}
|
||||
/*---------------------------------------------------------------------------*/
|
||||
/*--------------------------------- RPL ----------------------------------*/
|
||||
/*---------------------------------------------------------------------------*/
|
||||
/* TODO: Put rpl code into another file, once it stabilizes */
|
||||
/* Set up fallback interface links to direct stack tcpip output to ethernet */
|
||||
static void
|
||||
init(void)
|
||||
@ -126,12 +136,11 @@ static void
|
||||
output(void)
|
||||
{
|
||||
// if(uip_ipaddr_cmp(&last_sender, &UIP_IP_BUF->srcipaddr)) {
|
||||
/* Do not bounce packets back over SLIP if the packet was received
|
||||
over SLIP */
|
||||
// PRINTF("slip-bridge: Destination off-link but no route\n");
|
||||
/* Do not bounce packets back over USB if the packet was received from USB */
|
||||
// PRINTA("JACKDAW router: Destination off-link but no route\n");
|
||||
// } else {
|
||||
PRINTF("SUT: %u\n", uip_len);
|
||||
mac_LowpanToEthernet();
|
||||
PRINTD("SUT: %u\n", uip_len);
|
||||
mac_LowpanToEthernet(); //bounceback trap is done in lowpanToEthernet
|
||||
// }
|
||||
}
|
||||
const struct uip_fallback_interface rpl_interface = {
|
||||
@ -157,11 +166,12 @@ PROCESS_THREAD(border_router_process, ev, data)
|
||||
memcpy_P(buf,dag_id,sizeof(dag_id));
|
||||
dag = rpl_set_root((uip_ip6addr_t *)buf);
|
||||
|
||||
/* Assign bbbb::200 to the uip stack, and bbbb::1 to the host network interface, e.g. $ip -6 address add bbbb::1/64 dev usb0 */
|
||||
/* Note the jackdaw uip stack will get packets intended for usb if they have the same address! */
|
||||
/* Assign separate addresses to the jackdaw uip stack and the host network interface, but with the same prefix */
|
||||
/* E.g. bbbb::200 to the jackdaw and bbbb::1 to the host network interface with $ip -6 address add bbbb::1/64 dev usb0 */
|
||||
/* Otherwise the host will trap packets intended for the jackdaw, just as the jackdaw will trap RF packets intended for the host */
|
||||
/* $ifconfig usb0 -arp on Ubuntu to skip the neighbor solicitations. Add explicit neighbors on other OSs */
|
||||
if(dag != NULL) {
|
||||
PRINTF("created a new RPL dag\n");
|
||||
PRINTD("created a new RPL dag\n");
|
||||
|
||||
#if UIP_CONF_ROUTER_RECEIVE_RA
|
||||
//Contiki stack will shut down until assigned an address from the interface RA
|
||||
@ -181,6 +191,7 @@ PROCESS_THREAD(border_router_process, ev, data)
|
||||
|
||||
while(1) {
|
||||
PROCESS_YIELD();
|
||||
/* Local and global dag repair can be done from the jackdaw menu */
|
||||
// rpl_set_prefix(rpl_get_dag(RPL_ANY_INSTANCE), &ipaddr, 64);
|
||||
// rpl_repair_dag(rpl_get_dag(RPL_ANY_INSTANCE));
|
||||
|
||||
@ -194,74 +205,47 @@ PROCESS_THREAD(border_router_process, ev, data)
|
||||
|
||||
/*-------------------------------------------------------------------------*/
|
||||
/*----------------------Configuration of the .elf file---------------------*/
|
||||
typedef struct {unsigned char B2;unsigned char B1;unsigned char B0;} __signature_t;
|
||||
#if 1
|
||||
/* The proper way to set the signature is */
|
||||
#include <avr/signature.h>
|
||||
#else
|
||||
/* Older avr-gcc's may not define the needed SIGNATURE bytes. Do it manually if you get an error */
|
||||
typedef struct {const unsigned char B2;const unsigned char B1;const unsigned char B0;} __signature_t;
|
||||
#define SIGNATURE __signature_t __signature __attribute__((section (".signature")))
|
||||
SIGNATURE = {
|
||||
/* Older AVR-GCCs may not define the SIGNATURE_n bytes so use explicit values */
|
||||
.B2 = 0x82,//SIGNATURE_2, //AT90USB128x
|
||||
.B1 = 0x97,//SIGNATURE_1, //128KB flash
|
||||
.B0 = 0x1E,//SIGNATURE_0, //Atmel
|
||||
};
|
||||
#endif
|
||||
|
||||
FUSES ={.low = 0xde, .high = 0x99, .extended = 0xff,};
|
||||
|
||||
/* Put default MAC address in EEPROM */
|
||||
#if !JACKDAW_CONF_USE_SETTINGS
|
||||
uint8_t mac_address[8] EEMEM = {0x02, 0x12, 0x13, 0xff, 0xfe, 0x14, 0x15, 0x16};
|
||||
#endif
|
||||
|
||||
static uint8_t get_channel_from_eeprom() {
|
||||
#if JACKDAW_CONF_USE_SETTINGS
|
||||
uint8_t chan = settings_get_uint8(SETTINGS_KEY_CHANNEL, 0);
|
||||
if(!chan)
|
||||
chan = RF_CHANNEL;
|
||||
return chan;
|
||||
#else
|
||||
uint8_t eeprom_channel;
|
||||
uint8_t eeprom_check;
|
||||
|
||||
eeprom_channel = eeprom_read_byte((uint8_t *)9);
|
||||
eeprom_check = eeprom_read_byte((uint8_t *)10);
|
||||
|
||||
if(eeprom_channel==~eeprom_check)
|
||||
return eeprom_channel;
|
||||
|
||||
/* Save the default settings into program flash memory */
|
||||
uint8_t default_mac_address[8] PROGMEM = {0x02, 0x12, 0x13, 0xff, 0xfe, 0x14, 0x15, 0x16};
|
||||
#ifdef CHANNEL_802_15_4
|
||||
return(CHANNEL_802_15_4);
|
||||
uint8_t default_channel PROGMEM = CHANNEL_802_15_4;
|
||||
#else
|
||||
return 26;
|
||||
#endif
|
||||
|
||||
uint8_t default_channel PROGMEM = 26;
|
||||
#endif
|
||||
|
||||
}
|
||||
|
||||
static bool
|
||||
get_eui64_from_eeprom(uint8_t macptr[8]) {
|
||||
#if JACKDAW_CONF_USE_SETTINGS
|
||||
size_t size = 8;
|
||||
|
||||
if(settings_get(SETTINGS_KEY_EUI64, 0, (unsigned char*)macptr, &size)==SETTINGS_STATUS_OK)
|
||||
return true;
|
||||
|
||||
// Fallback to reading the traditional mac address
|
||||
eeprom_read_block ((void *)macptr, 0, 8);
|
||||
#ifdef IEEE802154_PANID
|
||||
uint16_t default_panid PROGMEM = IEEE802154_PANID;
|
||||
#else
|
||||
eeprom_read_block ((void *)macptr, &mac_address, 8);
|
||||
uint16_t default_panid PROGMEM = 0xABCD;
|
||||
#endif
|
||||
#ifdef IEEE802154_PANADDR
|
||||
uint16_t default_panaddr PROGMEM = IEEE802154_PANID;
|
||||
#else
|
||||
uint16_t default_panaddr PROGMEM = 0;
|
||||
#endif
|
||||
#ifdef RF230_MAX_TX_POWER
|
||||
uint8_t default_txpower PROGMEM = RF230_MAX_TX_POWER;
|
||||
#else
|
||||
uint8_t default_txpower PROGMEM = 0;
|
||||
#endif
|
||||
return macptr[0]!=0xFF;
|
||||
}
|
||||
|
||||
#if JACKDAW_CONF_RANDOM_MAC
|
||||
static bool
|
||||
set_eui64_to_eeprom(const uint8_t macptr[8]) {
|
||||
#if JACKDAW_CONF_USE_SETTINGS
|
||||
return settings_set(SETTINGS_KEY_EUI64, macptr, 8)==SETTINGS_STATUS_OK;
|
||||
#else
|
||||
eeprom_write_block((void *)macptr, &mac_address, 8);
|
||||
return true;
|
||||
#endif
|
||||
}
|
||||
|
||||
#include "rng.h"
|
||||
static void
|
||||
generate_new_eui64(uint8_t eui64[8]) {
|
||||
eui64[0] = 0x02;
|
||||
@ -275,33 +259,141 @@ generate_new_eui64(uint8_t eui64[8]) {
|
||||
}
|
||||
#endif /* JACKDAW_CONF_RANDOM_MAC */
|
||||
|
||||
static uint16_t
|
||||
get_panid_from_eeprom(void) {
|
||||
#if JACKDAW_CONF_USE_SETTINGS
|
||||
uint16_t x = settings_get_uint16(SETTINGS_KEY_PAN_ID, 0);
|
||||
if(!x)
|
||||
x = IEEE802154_PANID;
|
||||
#if !JACKDAW_CONF_USE_SETTINGS
|
||||
/****************************No settings manager*****************************/
|
||||
/* If not using the settings manager, put the default values into EEMEM
|
||||
* These can be manually changed and kept over program reflash.
|
||||
* The channel and bit complement are used to check EEMEM integrity,
|
||||
* If corrupt all values will be rewritten with the default flash values.
|
||||
* To make this work, get the channel before anything else.
|
||||
*/
|
||||
|
||||
uint8_t eemem_mac_address[8] EEMEM = {0x02, 0x12, 0x13, 0xff, 0xfe, 0x14, 0x15, 0x16};
|
||||
#ifdef CHANNEL_802_15_4
|
||||
uint8_t eemem_channel[2] EEMEM = {CHANNEL_802_15_4, ~CHANNEL_802_15_4};
|
||||
#else
|
||||
uint8_t eemem_channel[2] EMEM = {26, ~26};
|
||||
#endif
|
||||
#ifdef IEEE802154_PANID
|
||||
uint16_t eemem_panid EEMEM = IEEE802154_PANID;
|
||||
#else
|
||||
uint16_t eemem_panid EEMEM = 0xABCD;
|
||||
#endif
|
||||
#ifdef IEEE802154_PANADDR
|
||||
uint16_t eemem_panaddr EEMEM = IEEE802154_PANID;
|
||||
#else
|
||||
uint16_t eemem_panaddr EEMEM = 0;
|
||||
#endif
|
||||
#ifdef RF230_MAX_TX_POWER
|
||||
uint8_t eemem_txpower EEMEM = RF230_MAX_TX_POWER;
|
||||
#else
|
||||
uint8_t eemem_txpower EEMEM = 0;
|
||||
#endif
|
||||
static uint8_t get_channel_from_eeprom() {
|
||||
uint8_t x[2];
|
||||
*(uint16_t *)x = eeprom_read_word ((uint16_t *)&eemem_channel);
|
||||
if((uint8_t)x[0]!=(uint8_t)~x[1]) {//~x[1] can promote comparison to 16 bit
|
||||
/* Verification fails, rewrite everything */
|
||||
uint8_t mac[8];
|
||||
#if JACKDAW_CONF_RANDOM_MAC
|
||||
PRINTA("Generating random MAC address.\n");
|
||||
generate_new_eui64(&mac);
|
||||
#else
|
||||
{uint8_t i; for (i=0;i<8;i++) mac[i] = pgm_read_byte_near(default_mac_address+i);}
|
||||
#endif
|
||||
eeprom_write_block(&mac, &eemem_mac_address, 8);
|
||||
eeprom_write_word(&eemem_panid , pgm_read_word_near(&default_panid));
|
||||
eeprom_write_word(&eemem_panaddr, pgm_read_word_near(&default_panaddr));
|
||||
eeprom_write_byte(&eemem_txpower, pgm_read_byte_near(&default_txpower));
|
||||
x[0] = pgm_read_byte_near(&default_channel);
|
||||
x[1]= ~x[0];
|
||||
eeprom_write_word((uint16_t *)&eemem_channel, *(uint16_t *)x);
|
||||
}
|
||||
return x[0];
|
||||
}
|
||||
static bool get_eui64_from_eeprom(uint8_t macptr[8]) {
|
||||
eeprom_read_block ((void *)macptr, &eemem_mac_address, 8);
|
||||
return macptr[0]!=0xFF;
|
||||
}
|
||||
static uint16_t get_panid_from_eeprom(void) {
|
||||
return eeprom_read_word(&eemem_panid);
|
||||
}
|
||||
static uint16_t get_panaddr_from_eeprom(void) {
|
||||
return eeprom_read_word (&eemem_panaddr);
|
||||
}
|
||||
static uint8_t get_txpower_from_eeprom(void)
|
||||
{
|
||||
return eeprom_read_byte(&eemem_txpower);
|
||||
}
|
||||
|
||||
#else /* !JACKDAW_CONF_USE_SETTINGS */
|
||||
/******************************Settings manager******************************/
|
||||
static uint8_t get_channel_from_eeprom() {
|
||||
uint8_t x = settings_get_uint8(SETTINGS_KEY_CHANNEL, 0);
|
||||
if(!x) x = pgm_read_byte_near(&default_channel);
|
||||
return x;
|
||||
#else
|
||||
// TODO: Writeme!
|
||||
return IEEE802154_PANID;
|
||||
#endif
|
||||
}
|
||||
|
||||
static uint16_t
|
||||
get_panaddr_from_eeprom(void) {
|
||||
#if JACKDAW_CONF_USE_SETTINGS
|
||||
return settings_get_uint16(SETTINGS_KEY_PAN_ADDR, 0);
|
||||
static bool get_eui64_from_eeprom(uint8_t macptr[8]) {
|
||||
size_t size = 8;
|
||||
if(settings_get(SETTINGS_KEY_EUI64, 0, (unsigned char*)macptr, &size)==SETTINGS_STATUS_OK) {
|
||||
PRINTD("<=Get EEPROM MAC address.\n");
|
||||
return true;
|
||||
}
|
||||
#if JACKDAW_CONF_RANDOM_MAC
|
||||
PRINTA("--Generating random MAC address.\n");
|
||||
generate_new_eui64(macptr);
|
||||
#else
|
||||
// TODO: Writeme!
|
||||
return 0;
|
||||
{uint8_t i;for (i=0;i<8;i++) macptr[i] = pgm_read_byte_near(default_mac_address+i);}
|
||||
#endif
|
||||
settings_add(SETTINGS_KEY_EUI64,(unsigned char*)macptr,8);
|
||||
PRINTA("->Set EEPROM MAC address.\n");
|
||||
return true;
|
||||
}
|
||||
|
||||
static uint16_t get_panid_from_eeprom(void) {
|
||||
uint16_t x;
|
||||
if (settings_check(SETTINGS_KEY_PAN_ID,0)) {
|
||||
x = settings_get_uint16(SETTINGS_KEY_PAN_ID,0);
|
||||
PRINTD("<-Get EEPROM PAN ID of %04x.\n",x);
|
||||
} else {
|
||||
x=pgm_read_word_near(&default_panid);
|
||||
if (settings_add_uint16(SETTINGS_KEY_PAN_ID,x)==SETTINGS_STATUS_OK) {
|
||||
PRINTA("->Set EEPROM PAN ID to %04x.\n",x);
|
||||
}
|
||||
}
|
||||
return x;
|
||||
}
|
||||
static uint16_t get_panaddr_from_eeprom(void) {
|
||||
uint16_t x;
|
||||
if (settings_check(SETTINGS_KEY_PAN_ADDR,0)) {
|
||||
x = settings_get_uint16(SETTINGS_KEY_PAN_ADDR,0);
|
||||
PRINTD("<-Get EEPROM PAN address of %04x.\n",x);
|
||||
} else {
|
||||
x=pgm_read_word_near(&default_panaddr);
|
||||
if (settings_add_uint16(SETTINGS_KEY_PAN_ADDR,x)==SETTINGS_STATUS_OK) {
|
||||
PRINTA("->Set EEPROM PAN address to %04x.\n",x);
|
||||
}
|
||||
}
|
||||
return x;
|
||||
}
|
||||
static uint8_t get_txpower_from_eeprom(void) {
|
||||
uint8_t x;
|
||||
if (settings_check(SETTINGS_KEY_TXPOWER,0)) {
|
||||
x = settings_get_uint8(SETTINGS_KEY_TXPOWER,0);
|
||||
PRINTD("<-Get EEPROM tx power of %d. (0=max)\n",x);
|
||||
} else {
|
||||
x=pgm_read_byte_near(&default_txpower);
|
||||
if (settings_add_uint8(SETTINGS_KEY_TXPOWER,x)==SETTINGS_STATUS_OK) {
|
||||
PRINTA("->Set EEPROM tx power of %d. (0=max)\n",x);
|
||||
}
|
||||
}
|
||||
return x;
|
||||
}
|
||||
#endif /* !JACKDAW_CONF_USE_SETTINGS */
|
||||
|
||||
/*-------------------------------------------------------------------------*/
|
||||
/*-----------------------------Low level initialization--------------------*/
|
||||
static void initialize(void) {
|
||||
|
||||
watchdog_init();
|
||||
watchdog_start();
|
||||
|
||||
@ -315,7 +407,7 @@ uint16_t p=(uint16_t)&__bss_end;
|
||||
do {
|
||||
*(uint16_t *)p = 0x4242;
|
||||
p+=100;
|
||||
} while (p<RAMEND-100);
|
||||
} while (p<SP-100); //don't overwrite our own stack
|
||||
}
|
||||
#endif
|
||||
|
||||
@ -326,28 +418,64 @@ uint16_t p=(uint16_t)&__bss_end;
|
||||
/* Clock */
|
||||
clock_init();
|
||||
|
||||
/* Leds are referred to by number to prevent any possible confusion :) */
|
||||
/* Led0 Blue Led1 Red Led2 Green Led3 Yellow */
|
||||
Leds_init();
|
||||
Led1_on();
|
||||
|
||||
#if USB_CONF_RS232
|
||||
/* Use rs232 port for serial out (tx, rx, gnd are the three pads behind jackdaw leds */
|
||||
rs232_init(RS232_PORT_0, USART_BAUD_57600,USART_PARITY_NONE | USART_STOP_BITS_1 | USART_DATA_BITS_8);
|
||||
/* Redirect stdout to second port */
|
||||
rs232_redirect_stdout(RS232_PORT_0);
|
||||
#if ANNOUNCE
|
||||
printf_P(PSTR("\n\n\n********BOOTING CONTIKI*********\n"));
|
||||
PRINTA("\n\n*******Booting %s*******\n",CONTIKI_VERSION_STRING);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
Leds_init();
|
||||
|
||||
/* rtimer init needed for low power protocols */
|
||||
rtimer_init();
|
||||
|
||||
/* Process subsystem. */
|
||||
process_init();
|
||||
|
||||
/* etimer process must be started before ctimer init */
|
||||
/* etimer process must be started before USB or ctimer init */
|
||||
process_start(&etimer_process, NULL);
|
||||
|
||||
Led2_on();
|
||||
/* Now we can start USB enumeration */
|
||||
process_start(&usb_process, NULL);
|
||||
|
||||
/* Start CDC enumeration, bearing in mind that it may fail */
|
||||
/* Hopefully we'll get a stdout for startup messages, if we don't already */
|
||||
#if USB_CONF_SERIAL
|
||||
process_start(&cdc_process, NULL);
|
||||
{unsigned short i;
|
||||
for (i=0;i<65535;i++) {
|
||||
process_run();
|
||||
watchdog_periodic();
|
||||
if (stdout) break;
|
||||
}
|
||||
#if !USB_CONF_RS232
|
||||
PRINTA("\n\n*******Booting %s*******\n",CONTIKI_VERSION_STRING);
|
||||
#endif
|
||||
}
|
||||
#endif
|
||||
if (!stdout) Led3_on();
|
||||
|
||||
#if RF230BB
|
||||
#if JACKDAW_CONF_USE_SETTINGS
|
||||
PRINTA("Settings manager will be used.\n");
|
||||
#else
|
||||
{uint8_t x[2];
|
||||
*(uint16_t *)x = eeprom_read_word((uint16_t *)&eemem_channel);
|
||||
if((uint8_t)x[0]!=(uint8_t)~x[1]) {
|
||||
PRINTA("Invalid EEPROM settings detected. Rewriting with default values.\n");
|
||||
get_channel_from_eeprom();
|
||||
}
|
||||
}
|
||||
#endif
|
||||
|
||||
ctimer_init();
|
||||
/* Start radio and radio receive process */
|
||||
/* Note this starts RF230 process, so must be done after process_init */
|
||||
@ -356,36 +484,9 @@ uint16_t p=(uint16_t)&__bss_end;
|
||||
/* Set addresses BEFORE starting tcpip process */
|
||||
|
||||
memset(&tmp_addr, 0, sizeof(rimeaddr_t));
|
||||
if(!get_eui64_from_eeprom(tmp_addr.u8)) {
|
||||
#if JACKDAW_CONF_RANDOM_MAC
|
||||
// It doesn't look like we have a valid EUI-64 address
|
||||
// so let's try to make a new one from scratch.
|
||||
Leds_off();
|
||||
Led2_on();
|
||||
generate_new_eui64(tmp_addr.u8);
|
||||
if(!set_eui64_to_eeprom(tmp_addr.u8)) {
|
||||
watchdog_periodic();
|
||||
int i;
|
||||
for(i=0;i<20;i++) {
|
||||
Led1_toggle();
|
||||
_delay_ms(100);
|
||||
}
|
||||
Led1_off();
|
||||
}
|
||||
Led2_off();
|
||||
#else
|
||||
tmp_addr.u8[0]=0x02;
|
||||
tmp_addr.u8[1]=0x12;
|
||||
tmp_addr.u8[2]=0x13;
|
||||
tmp_addr.u8[3]=0xff;
|
||||
tmp_addr.u8[4]=0xfe;
|
||||
tmp_addr.u8[5]=0x14;
|
||||
tmp_addr.u8[6]=0x15;
|
||||
tmp_addr.u8[7]=0x16;
|
||||
#endif /* JACKDAW_CONF_RANDOM_MAC */
|
||||
}
|
||||
|
||||
|
||||
if(get_eui64_from_eeprom(tmp_addr.u8));
|
||||
|
||||
//Fix MAC address
|
||||
init_net();
|
||||
|
||||
@ -399,12 +500,8 @@ uint16_t p=(uint16_t)&__bss_end;
|
||||
(uint8_t *)&tmp_addr.u8
|
||||
);
|
||||
|
||||
#if JACKDAW_CONF_USE_SETTINGS
|
||||
/* Allow radio code to overrite power for testing miniature Raven mesh */
|
||||
#ifndef RF230_MAX_TX_POWER
|
||||
rf230_set_txpower(settings_get_uint8(SETTINGS_KEY_TXPOWER,0));
|
||||
#endif
|
||||
#endif
|
||||
rf230_set_channel(get_channel_from_eeprom());
|
||||
rf230_set_txpower(get_txpower_from_eeprom());
|
||||
|
||||
rimeaddr_set_node_addr(&tmp_addr);
|
||||
|
||||
@ -414,33 +511,31 @@ uint16_t p=(uint16_t)&__bss_end;
|
||||
NETSTACK_MAC.init();
|
||||
NETSTACK_NETWORK.init();
|
||||
|
||||
rf230_set_channel(get_channel_from_eeprom());
|
||||
|
||||
#if ANNOUNCE && USB_CONF_RS232
|
||||
printf_P(PSTR("MAC address %x:%x:%x:%x:%x:%x:%x:%x\n\r"),tmp_addr.u8[0],tmp_addr.u8[1],tmp_addr.u8[2],tmp_addr.u8[3],tmp_addr.u8[4],tmp_addr.u8[5],tmp_addr.u8[6],tmp_addr.u8[7]);
|
||||
printf_P(PSTR("%s %s, channel %u"),NETSTACK_MAC.name, NETSTACK_RDC.name,rf230_get_channel());
|
||||
#if ANNOUNCE
|
||||
PRINTA("MAC address %x:%x:%x:%x:%x:%x:%x:%x\n\r",tmp_addr.u8[0],tmp_addr.u8[1],tmp_addr.u8[2],tmp_addr.u8[3],tmp_addr.u8[4],tmp_addr.u8[5],tmp_addr.u8[6],tmp_addr.u8[7]);
|
||||
PRINTA("%s %s, channel %u",NETSTACK_MAC.name, NETSTACK_RDC.name,rf230_get_channel());
|
||||
if (NETSTACK_RDC.channel_check_interval) {
|
||||
unsigned short tmp;
|
||||
tmp=CLOCK_SECOND / (NETSTACK_RDC.channel_check_interval == 0 ? 1:\
|
||||
NETSTACK_RDC.channel_check_interval());
|
||||
if (tmp<65535) printf_P(PSTR(", check rate %u Hz"),tmp);
|
||||
if (tmp<65535) PRINTA(", check rate %u Hz",tmp);
|
||||
}
|
||||
printf_P(PSTR("\n"));
|
||||
PRINTA("\n");
|
||||
#endif
|
||||
|
||||
#if UIP_CONF_IPV6_RPL
|
||||
#if RPL_BORDER_ROUTER
|
||||
process_start(&tcpip_process, NULL);
|
||||
process_start(&border_router_process, NULL);
|
||||
PRINTF ("RPL Border Router Started\n");
|
||||
PRINTD ("RPL Border Router Started\n");
|
||||
#else
|
||||
process_start(&tcpip_process, NULL);
|
||||
PRINTF ("RPL Started\n");
|
||||
PRINTD ("RPL Started\n");
|
||||
#endif
|
||||
#if RPL_HTTPD_SERVER
|
||||
extern struct process httpd_process;
|
||||
process_start(&httpd_process, NULL);
|
||||
PRINTF ("Webserver Started\n");
|
||||
PRINTD ("Webserver Started\n");
|
||||
#endif
|
||||
#endif /* UIP_CONF_IPV6_RPL */
|
||||
|
||||
@ -450,40 +545,21 @@ uint16_t p=(uint16_t)&__bss_end;
|
||||
process_start(&tcpip_process, NULL);
|
||||
#endif /* RF230BB */
|
||||
|
||||
/* Setup USB */
|
||||
process_start(&usb_process, NULL);
|
||||
#if USB_CONF_SERIAL
|
||||
process_start(&cdc_process, NULL);
|
||||
#endif
|
||||
/* Start ethernet network and storage process */
|
||||
process_start(&usb_eth_process, NULL);
|
||||
#if USB_CONF_STORAGE
|
||||
process_start(&storage_process, NULL);
|
||||
#endif
|
||||
|
||||
|
||||
#if ANNOUNCE
|
||||
#if USB_CONF_SERIAL&&!USB_CONF_RS232
|
||||
{unsigned short i;
|
||||
printf_P(PSTR("\n\n\n********BOOTING CONTIKI*********\n\r"));
|
||||
/* Allow USB CDC to keep up with printfs */
|
||||
for (i=0;i<8000;i++) process_run();
|
||||
#if RF230BB
|
||||
printf_P(PSTR("MAC address %x:%x:%x:%x:%x:%x:%x:%x\n\r"),tmp_addr.u8[0],tmp_addr.u8[1],tmp_addr.u8[2],tmp_addr.u8[3],tmp_addr.u8[4],tmp_addr.u8[5],tmp_addr.u8[6],tmp_addr.u8[7]);
|
||||
for (i=0;i<8000;i++) process_run();
|
||||
printf_P(PSTR("%s %s, channel %u"),NETSTACK_MAC.name, NETSTACK_RDC.name,rf230_get_channel());
|
||||
if (NETSTACK_RDC.channel_check_interval) {
|
||||
i=CLOCK_SECOND / (NETSTACK_RDC.channel_check_interval == 0 ? 1:\
|
||||
NETSTACK_RDC.channel_check_interval());
|
||||
if (i<65535) printf_P(PSTR(", check rate %u Hz"),i);
|
||||
}
|
||||
printf_P(PSTR("\n\r"));
|
||||
for (i=0;i<8000;i++) process_run();
|
||||
#endif /* RF230BB */
|
||||
printf_P(PSTR("System online.\n\r"));
|
||||
}
|
||||
#elif USB_CONF_RS232
|
||||
printf_P(PSTR("System online.\n"));
|
||||
#if USB_CONF_RS232
|
||||
PRINTA("Online.\n");
|
||||
#else
|
||||
PRINTA("Online. Type ? for Jackdaw menu.\n");
|
||||
#endif
|
||||
#endif /* ANNOUNCE */
|
||||
#endif
|
||||
|
||||
Leds_off();
|
||||
}
|
||||
|
||||
/*-------------------------------------------------------------------------*/
|
||||
@ -496,13 +572,15 @@ main(void)
|
||||
|
||||
/* Initialize in a subroutine to maximize stack space */
|
||||
initialize();
|
||||
|
||||
#if DEBUG
|
||||
{struct process *p;
|
||||
for(p = PROCESS_LIST();p != NULL; p = ((struct process *)p->next)) {
|
||||
printf_P(PSTR("Process=%p Thread=%p Name=\"%s\" \n"),p,p->thread,p->name);
|
||||
PRINTA("Process=%p Thread=%p Name=\"%s\" \n",p,p->thread,PROCESS_NAME_STRING(p));
|
||||
}
|
||||
}
|
||||
#endif
|
||||
|
||||
while(1) {
|
||||
process_run();
|
||||
|
||||
@ -512,57 +590,118 @@ main(void)
|
||||
#ifdef RF230_MIN_RX_POWER
|
||||
uint8_t lastprint;
|
||||
if (rf230_last_rssi != lastprint) { //can be set in halbb.c interrupt routine
|
||||
printf_P(PSTR("%u "),rf230_last_rssi);
|
||||
PRINTA("%u ",rf230_last_rssi);
|
||||
lastprint=rf230_last_rssi;
|
||||
}
|
||||
#endif
|
||||
|
||||
#if 0
|
||||
/* Clock.c can trigger a periodic PLL calibration in the RF230BB driver.
|
||||
* This can show when that happens.
|
||||
*/
|
||||
extern uint8_t rf230_calibrated;
|
||||
if (rf230_calibrated) {
|
||||
PRINTA("\nRF230 calibrated!\n");
|
||||
rf230_calibrated=0;
|
||||
}
|
||||
#endif
|
||||
|
||||
#if TESTRTIMER
|
||||
if (rtimerflag) { //8 seconds is maximum interval, my jackdaw 4% slow
|
||||
/* Timeout can be increased up to 8 seconds maximum.
|
||||
* A one second cycle is convenient for triggering the various debug printouts.
|
||||
* The triggers are staggered to avoid printing everything at once.
|
||||
* My Jackdaw is 4% slow.
|
||||
*/
|
||||
if (rtimerflag) {
|
||||
rtimer_set(&rt, RTIMER_NOW()+ RTIMER_ARCH_SECOND*1UL, 1,(void *) rtimercycle, NULL);
|
||||
rtimerflag=0;
|
||||
|
||||
#if STAMPS
|
||||
if ((rtime%STAMPS)==0) {
|
||||
printf("%us ",rtime);
|
||||
}
|
||||
if ((rtime%STAMPS)==0) {
|
||||
PRINTA("%us ",rtime);
|
||||
if (rtime%STAMPS*10) PRINTA("\n");
|
||||
}
|
||||
#endif
|
||||
rtime+=1;
|
||||
#if PINGS
|
||||
if ((rtime%PINGS)==0) {
|
||||
PRINTF("**Ping\n");
|
||||
pingsomebody();
|
||||
}
|
||||
|
||||
#if PINGS && UIP_CONF_IPV6_RPL
|
||||
extern void raven_ping6(void);
|
||||
if ((rtime%PINGS)==1) {
|
||||
PRINTA("**Ping\n");
|
||||
raven_ping6();
|
||||
}
|
||||
#endif
|
||||
|
||||
#if ROUTES && UIP_CONF_IPV6_RPL
|
||||
if ((rtime%ROUTES)==2) {
|
||||
|
||||
extern uip_ds6_nbr_t uip_ds6_nbr_cache[];
|
||||
extern uip_ds6_route_t uip_ds6_routing_table[];
|
||||
extern uip_ds6_netif_t uip_ds6_if;
|
||||
|
||||
uint8_t i,j;
|
||||
PRINTA("\nAddresses [%u max]\n",UIP_DS6_ADDR_NB);
|
||||
for (i=0;i<UIP_DS6_ADDR_NB;i++) {
|
||||
if (uip_ds6_if.addr_list[i].isused) {
|
||||
uip_debug_ipaddr_print(&uip_ds6_if.addr_list[i].ipaddr);
|
||||
PRINTA("\n");
|
||||
}
|
||||
}
|
||||
PRINTA("\nNeighbors [%u max]\n",UIP_DS6_NBR_NB);
|
||||
for(i = 0,j=1; i < UIP_DS6_NBR_NB; i++) {
|
||||
if(uip_ds6_nbr_cache[i].isused) {
|
||||
uip_debug_ipaddr_print(&uip_ds6_nbr_cache[i].ipaddr);
|
||||
PRINTA("\n");
|
||||
j=0;
|
||||
}
|
||||
}
|
||||
if (j) PRINTA(" <none>");
|
||||
PRINTA("\nRoutes [%u max]\n",UIP_DS6_ROUTE_NB);
|
||||
for(i = 0,j=1; i < UIP_DS6_ROUTE_NB; i++) {
|
||||
if(uip_ds6_routing_table[i].isused) {
|
||||
uip_debug_ipaddr_print(&uip_ds6_routing_table[i].ipaddr);
|
||||
PRINTA("/%u (via ", uip_ds6_routing_table[i].length);
|
||||
uip_debug_ipaddr_print(&uip_ds6_routing_table[i].nexthop);
|
||||
// if(uip_ds6_routing_table[i].state.lifetime < 600) {
|
||||
PRINTA(") %lus\n", uip_ds6_routing_table[i].state.lifetime);
|
||||
// } else {
|
||||
// PRINTA(")\n");
|
||||
// }
|
||||
j=0;
|
||||
}
|
||||
}
|
||||
if (j) PRINTA(" <none>");
|
||||
PRINTA("\n---------\n");
|
||||
}
|
||||
#endif
|
||||
|
||||
#if STACKMONITOR && CONFIG_STACK_MONITOR
|
||||
if ((rtime%STACKMONITOR)==3) {
|
||||
extern uint16_t __bss_end;
|
||||
uint16_t p=(uint16_t)&__bss_end;
|
||||
do {
|
||||
if (*(uint16_t *)p != 0x4242) {
|
||||
PRINTA("Never-used stack > %d bytes\n",p-(uint16_t)&__bss_end);
|
||||
break;
|
||||
}
|
||||
p+=100;
|
||||
} while (p<RAMEND-10);
|
||||
}
|
||||
#endif
|
||||
|
||||
}
|
||||
#endif /* TESTRTIMER */
|
||||
|
||||
/* Use with rf230bb.c DEBUGFLOW to show the sequence of driver calls from the uip stack */
|
||||
//Use with RF230BB DEBUGFLOW to show path through driver
|
||||
#if RF230BB&&0
|
||||
extern uint8_t debugflowsize,debugflow[];
|
||||
extern uint8_t debugflowsize,debugflow[]; //in rf230bb.c
|
||||
if (debugflowsize) {
|
||||
debugflow[debugflowsize]=0;
|
||||
printf("%s",debugflow);
|
||||
PRINTA("%s",debugflow);
|
||||
debugflowsize=0;
|
||||
}
|
||||
#endif
|
||||
|
||||
/* Use for low level interrupt debugging */
|
||||
#if RF230BB&&0
|
||||
extern uint8_t rf230interruptflag; //in halbb.c
|
||||
extern uint8_t rf230processflag; //in rf230bb.c
|
||||
if (rf230processflag) {
|
||||
printf("**RF230 process flag %u\n\r",rf230processflag);
|
||||
rf230processflag=0;
|
||||
}
|
||||
if (rf230interruptflag) {
|
||||
// if (rf230interruptflag!=11) {
|
||||
printf("**RF230 Interrupt %u\n\r",rf230interruptflag);
|
||||
// }
|
||||
rf230interruptflag=0;
|
||||
}
|
||||
#endif
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user