mirror of
https://github.com/oliverschmidt/contiki.git
synced 2024-08-27 16:28:56 +00:00
96 lines
3.2 KiB
Plaintext
96 lines
3.2 KiB
Plaintext
This directory contains the compiled code for the Contiki energy
|
|
estimation demonstration for ACM SenSys 2007. More information is
|
|
available in the handouts/ directory and at the Contiki website:
|
|
|
|
http://www.sics.se/contiki/
|
|
|
|
* INSTALLATION INSTRUCTIONS
|
|
|
|
Cygwin and Java (JRE) needs to be installed. The demo has been tested
|
|
on Microsoft Windows, but probably works under Linux too.
|
|
|
|
You need between two and eight Tmote Sky boards to run the demo: one
|
|
sink and between one and seven nodes. The nodes are numbered from 42
|
|
to 48, and 41 is the sink node.
|
|
|
|
Step 1: Unpack the zip file
|
|
|
|
unzip contiki-energest-demo.zip
|
|
|
|
Step 2: Change directory to the demo directory
|
|
|
|
cd contiki-energest-demo
|
|
|
|
Step 3: Connect the sink node to the PC. Remove all other Tmote Sky
|
|
nodes from the PC.
|
|
|
|
Step 4: Upload Contiki to the sink:
|
|
|
|
make upload-sink
|
|
|
|
Step 5: Remove the sink node from the PC.
|
|
|
|
Step 6: Connect one of the non-sink nodes to the PC
|
|
|
|
Step 7: Upload Contiki to the node:
|
|
|
|
make upload-node-42
|
|
|
|
This takes some time. The red LED should be lit when the
|
|
uploading is finished. We have found that in some cases brand
|
|
new Tmote Sky boards seem to cause a problem with Contiki and
|
|
the red LED does not light up. If so, try to wait a few
|
|
minutes (~10 minutes) with the Tmote Sky either inserted in
|
|
the PC, or powered with batteries. If the red LED goes on
|
|
after these minutes, repeat the "make upload-node-XX" to
|
|
upload Contiki again.
|
|
|
|
Step 8: Remove the Tmote Sky from the PC.
|
|
|
|
Step 9: Insert batteries into the Tmote Sky. The red LED should light
|
|
up.
|
|
|
|
Step 10: Repeat step 6 to step 9 for all non-sink nodes. Replace "make
|
|
upload-node-42" with "make upload-node-43", "make
|
|
upload-node-44", and so on.
|
|
|
|
Step 11: Insert the sink node to the PC again.
|
|
|
|
Step 12: Run the Java program:
|
|
|
|
make rundemo
|
|
|
|
NOTE: this uses the first Tmote Sky it finds as a
|
|
sink. Therefore, make sure that only one Tmote Sky (the sink) is
|
|
inserted.
|
|
|
|
Step 13: Push the "user" button on the Tmote Skys and watch their
|
|
power consumption go up and down.
|
|
|
|
|
|
* DEMO DESCRIPTION
|
|
|
|
Contiki continuously estimates the energy consumption of the
|
|
system. In this demonstration, seven Tmote Sky nodes, running Contiki,
|
|
estimates their energy consumption and send their power to a sink
|
|
node. The sink node is connected to the PC, and reports the nodes'
|
|
power to a Java program. The Java program shows the nodes' power
|
|
consumption for the last second.
|
|
|
|
When pushing the button on the nodes, they cycle through seven states
|
|
as below. This is reflected by their power consumption, as shown in
|
|
the Java program. The different states are:
|
|
|
|
* Red LED: sending one packet per second
|
|
* Green LED: radio listen 1% duty cycle
|
|
* Green, red LEDs: radio listen 10% duty cycle
|
|
* Blue LED: radio listen 100%
|
|
* Blue, red LEDs: radio listen 10%, CPU low-power mode disabled
|
|
* Blue, green LEDs: sending data 1.2 kilobytes/second
|
|
* Blue, green, red LEDs: sending data 12 kilobytes/second
|
|
|
|
When sending data, the radio is turned on for a while before the
|
|
transmission to check if it is possible to send the packet. This is
|
|
the reason why energy is spent on radio listening even when the nodes
|
|
are only sending data.
|